-
Nguyen Anh Quynh authored
I have another Argosy USB storage device, which has the same problem with the Argosy USB storage device already fixed in 2.6.27.7. But this device has another product ID (840:84), so this patch adds a new entry into unusual_devs to fix the mount problem. I enclose here two patches: one against 2.6.27.8, and another against the latest linus-git tree. The information about the Argosy device is like below: #lsusb -v -d 840:84 Bus 005 Device 005: ID 0840:0084 Argosy Research, Inc. Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x0840 Argosy Research, Inc. idProduct 0x0084 bcdDevice 0.01 iManufacturer 1 Generic iProduct 2 USB 2.0 Storage Device iSerial 3 8400000000002549 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 32 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xc0 Self Powered MaxPower 2mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 8 Mass Storage bInterfaceSubClass 6 SCSI bInterfaceProtocol 80 Bulk (Zip) iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0000 (Bus Powered) Before the patch, dmesg returns a lot of information like below (my dmesg is overflown): .... [ 138.833390] sd 7:0:0:0: [sdb] Add. Sense: No additional sense information [ 138.877631] sd 7:0:0:0: [sdb] Sense Key : No Sense [current] [ 138.877643] sd 7:0:0:0: [sdb] Add. Sense: No additional sense information [ 138.921906] sd 7:0:0:0: [sdb] Sense Key : No Sense [current] [ 138.921923] sd 7:0:0:0: [sdb] Add. Sense: No additional sense information .... After the fix, dmesg returns below information: .... usb 5-1: new high speed USB device using ehci_hcd and address 5 usb 5-1: configuration #1 chosen from 1 choice scsi7 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 5 usb-storage: waiting for device to settle before scanning usb-storage: device scan complete scsi 7:0:0:0: Direct-Access HTS54808 0M9AT00 MG4O PQ: 0 ANSI: 0 sd 7:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB) sd 7:0:0:0: [sdb] Write Protect is off sd 7:0:0:0: [sdb] Mode Sense: 03 00 00 00 sd 7:0:0:0: [sdb] Assuming drive cache: write through sd 7:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB) sd 7:0:0:0: [sdb] Write Protect is off sd 7:0:0:0: [sdb] Mode Sense: 03 00 00 00 sd 7:0:0:0: [sdb] Assuming drive cache: write through sdb: sdb1 sd 7:0:0:0: [sdb] Attached SCSI disk sd 7:0:0:0: Attached scsi generic sg1 type 0 kjournald starting. Commit interval 5 seconds EXT3 FS on sdb1, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. Cc: Kuniyasu Suzaki <k.suzaki@aist.go.jp> Signed-off-by: Nguyen Anh Quynh <aquynh@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
e2673b28