Doing suspend/resume on imx6q and imx53 boards with no SATA disk
attached will trigger the following warning.

------------[ cut here ]------------
WARNING: CPU: 0 PID: 661 at drivers/ata/libahci.c:224 ahci_enable_ahci+0x74/0x8)
Modules linked in:
CPU: 0 PID: 661 Comm: sh Tainted: G        W     3.15.0-rc5-next-20140521-000027
Backtrace:
[<80011c90>] (dump_backtrace) from [<80011e2c>] (show_stack+0x18/0x1c)
 r6:803a22f4 r5:00000000 r4:00000000 r3:00000000
[<80011e14>] (show_stack) from [<80661e60>] (dump_stack+0x88/0xa4)
[<80661dd8>] (dump_stack) from [<80028fdc>] (warn_slowpath_common+0x70/0x94)
 r5:00000009 r4:00000000
[<80028f6c>] (warn_slowpath_common) from [<80029024>] (warn_slowpath_null+0x24/)
 r8:808f68c4 r7:00000000 r6:00000000 r5:00000000 r4:e0810004
[<80029000>] (warn_slowpath_null) from [<803a22f4>] (ahci_enable_ahci+0x74/0x80)
[<803a2280>] (ahci_enable_ahci) from [<803a2324>] (ahci_reset_controller+0x24/0)
 r8:ddcd9410 r7:80351178 r6:ddcd9444 r5:dde8b850 r4:e0810000 r3:ddf35e90
[<803a2300>] (ahci_reset_controller) from [<803a2c68>] (ahci_platform_resume_ho)
 r7:80351178 r6:ddcd9444 r5:dde8b850 r4:ddcd9410
[<803a2c30>] (ahci_platform_resume_host) from [<803a38f0>] (imx_ahci_resume+0x2)
 r5:00000000 r4:ddcd9410
[<803a38c4>] (imx_ahci_resume) from [<803511ac>] (platform_pm_resume+0x34/0x54)
....

The reason is that the SATA controller has no working clock at this
point, and thus ahci_enable_ahci() fails to enable the controller.  In
case that there is no SATA disk attached, the imx_sata_disable() gets
called in ahci_imx_error_handler(), and both sata_clk and sata_ref_clk
will be disabled there.  Because all the imx_sata_enable() calls
afterward will return immediately due to imxpriv->no_device check, the
SATA controller working clock sata_clk will never get any chance to be
enabled again.

This is a regression caused by commit 90870d79 (ahci-imx: Port to
library-ised ahci_platform).  Before the commit, only sata_ref_clk is
managed by the driver in enable/disable function.  But after the commit,
all the clocks are enabled/disabled in a row by ahci platform helpers
ahci_platform_enable[disable]_clks.  Since ahb_clk is a bus clock which
does not have gate at all, and i.MX low-power hardware module already
manages sata_clk across suspend/resume cycle, the only clock that needs
to be managed by software is sata_ref_clk.

So instead of using ahci_platform_enable[disable]_clks to manage all
the clocks in a row from imx_sata_enable[disable], we should manage
only sata_ref_clk in there.
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Fixes: 90870d79 (ahci-imx: Port to library-ised ahci_platform)
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>