staging:iio:adc:lpc32xx Move out of staging.

There are a few more little cleanups that could be done on this driver, but
I don't think any are sufficient to justify not moving it out of staging.

It's a very simple driver (presumably for a simple part) so not much that can
go wrong.  I think it was only ever in staging because that's where IIO was
as a whole at the time and then we forgot about it!
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Roland Stigge <stigge@antcom.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

drivers/iio/adc/Kconfig

@@ -305,6 +305,18 @@ config LPC18XX_ADC
 	  To compile this driver as a module, choose M here: the module will be
 	  called lpc18xx_adc.
 
+config LPC32XX_ADC
+	tristate "NXP LPC32XX ADC"
+	depends on ARCH_LPC32XX || COMPILE_TEST
+	depends on HAS_IOMEM
+	help
+	  Say yes here to build support for the integrated ADC inside the
+	  LPC32XX SoC. Note that this feature uses the same hardware as the
+	  touchscreen driver, so you should either select only one of the two
+	  drivers (lpc32xx_adc or lpc32xx_ts) or, in the OpenFirmware case,
+	  activate only one via device tree selection.  Provides direct access
+	  via sysfs.
+
 config LTC2485
 	tristate "Linear Technology LTC2485 ADC driver"
 	depends on I2C

drivers/iio/adc/Makefile

@@ -30,6 +30,7 @@ obj-$(CONFIG_IMX7D_ADC) += imx7d_adc.o
 obj-$(CONFIG_INA2XX_ADC) += ina2xx-adc.o
 obj-$(CONFIG_LP8788_ADC) += lp8788_adc.o
 obj-$(CONFIG_LPC18XX_ADC) += lpc18xx_adc.o
+obj-$(CONFIG_LPC32XX_ADC) += lpc32xx_adc.o
 obj-$(CONFIG_LTC2485) += ltc2485.o
 obj-$(CONFIG_MAX1027) += max1027.o
 obj-$(CONFIG_MAX11100) += max11100.o

drivers/staging/iio/adc/Kconfig

@@ -80,16 +80,4 @@ config AD7280
 	  To compile this driver as a module, choose M here: the
 	  module will be called ad7280a
 
-config LPC32XX_ADC
-	tristate "NXP LPC32XX ADC"
-	depends on ARCH_LPC32XX || COMPILE_TEST
-	depends on HAS_IOMEM
-	help
-	  Say yes here to build support for the integrated ADC inside the
-	  LPC32XX SoC. Note that this feature uses the same hardware as the
-	  touchscreen driver, so you should either select only one of the two
-	  drivers (lpc32xx_adc or lpc32xx_ts) or, in the OpenFirmware case,
-	  activate only one via device tree selection.  Provides direct access
-	  via sysfs.
-
 endmenu

drivers/staging/iio/adc/Makefile

@@ -10,4 +10,3 @@ obj-$(CONFIG_AD7780) += ad7780.o
 obj-$(CONFIG_AD7816) += ad7816.o
 obj-$(CONFIG_AD7192) += ad7192.o
 obj-$(CONFIG_AD7280) += ad7280a.o
-obj-$(CONFIG_LPC32XX_ADC) += lpc32xx_adc.o