arm64: dts: add support for C3 based Amlogic AW409

Amlogic C3 is an advanced edge AI processor designed for smart IP camera
applications.

Add basic support for the C3 based Amlogic AW409 board, which describes
the following components: CPU, GIC, IRQ, Timer, UART. It's capable of
booting up into the serial console.
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
Link: https://lore.kernel.org/r/20230515093237.2203171-1-xianwei.zhao@amlogic.comSigned-off-by: Neil Armstrong <neil.armstrong@linaro.org>

arch/arm64/boot/dts/amlogic/Makefile

 # SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_MESON) += amlogic-c3-c302x-aw409.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-a1-ad401.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-axg-jethome-jethub-j100.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-axg-jethome-jethub-j110-rev-2.dtb

arch/arm64/boot/dts/amlogic/amlogic-c3-c302x-aw409.dts

+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Amlogic, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "amlogic-c3.dtsi"
+
+/ {
+	model = "Amlogic C302 aw409 Development Board";
+	compatible = "amlogic,aw409", "amlogic,c3";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	aliases {
+		serial0 = &uart_b;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x10000000>;
+	};
+};
+
+&uart_b {
+	status = "okay";
+};

arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi

+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Amlogic, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a35";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a35";
+			reg = <0x0 0x1>;
+			enable-method = "psci";
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	xtal: xtal-clk {
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		clock-output-names = "xtal";
+		#clock-cells = <0>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		gic: interrupt-controller@fff01000 {
+			compatible = "arm,gic-400";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0x0 0xfff01000 0 0x1000>,
+			      <0x0 0xfff02000 0 0x2000>,
+			      <0x0 0xfff04000 0 0x2000>,
+			      <0x0 0xfff06000 0 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
+		apb4: bus@fe000000 {
+			compatible = "simple-bus";
+			reg = <0x0 0xfe000000 0x0 0x480000>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges = <0x0 0x0 0x0 0xfe000000 0x0 0x480000>;
+
+			uart_b: serial@7a000 {
+				compatible = "amlogic,meson-s4-uart",
+					   "amlogic,meson-ao-uart";
+				reg = <0x0 0x7a000 0x0 0x18>;
+				interrupts = <GIC_SPI 169 IRQ_TYPE_EDGE_RISING>;
+				status = "disabled";
+				clocks = <&xtal>, <&xtal>, <&xtal>;
+				clock-names = "xtal", "pclk", "baud";
+			};
+
+		};
+	};
+};