Commit 038a9c3d authored by Maxim Sloyko's avatar Maxim Sloyko Committed by Guenter Roeck

hwmon: (pmbus/isl68137) Add driver for Intersil ISL68137 PWM Controller

Intersil ISL68137 is a digital output 7-phase configurable PWM
controller with an AVSBus interface.
Signed-off-by: default avatarMaxim Sloyko <maxims@google.com>
Signed-off-by: default avatarRobert Lippert <rlippert@google.com>
Signed-off-by: default avatarPatrick Venture <venture@google.com>
Signed-off-by: default avatarGuenter Roeck <linux@roeck-us.net>
parent 991d6799
Kernel driver isl68137
======================
Supported chips:
* Intersil ISL68137
Prefix: 'isl68137'
Addresses scanned: -
Datasheet: Publicly available at the Intersil website
https://www.intersil.com/content/dam/Intersil/documents/isl6/isl68137.pdf
Authors:
Maxim Sloyko <maxims@google.com>
Robert Lippert <rlippert@google.com>
Patrick Venture <venture@google.com>
Description
-----------
Intersil ISL68137 is a digital output 7-phase configurable PWM
controller with an AVSBus interface.
Usage Notes
-----------
This driver does not probe for PMBus devices. You will have to instantiate
devices explicitly.
The ISL68137 AVS operation mode must be enabled/disabled at runtime.
Beyond the normal sysfs pmbus attributes, the driver exposes a control attribute.
Additional Sysfs attributes
---------------------------
avs(0|1)_enable Controls the AVS state of each rail.
curr1_label "iin"
curr1_input Measured input current
curr1_crit Critical maximum current
curr1_crit_alarm Current critical high alarm
curr[2-3]_label "iout[1-2]"
curr[2-3]_input Measured output current
curr[2-3]_crit Critical maximum current
curr[2-3]_crit_alarm Current critical high alarm
in1_label "vin"
in1_input Measured input voltage
in1_lcrit Critical minimum input voltage
in1_lcrit_alarm Input voltage critical low alarm
in1_crit Critical maximum input voltage
in1_crit_alarm Input voltage critical high alarm
in[2-3]_label "vout[1-2]"
in[2-3]_input Measured output voltage
in[2-3]_lcrit Critical minimum output voltage
in[2-3]_lcrit_alarm Output voltage critical low alarm
in[2-3]_crit Critical maximum output voltage
in[2-3]_crit_alarm Output voltage critical high alarm
power1_label "pin"
power1_input Measured input power
power1_alarm Input power high alarm
power[2-3]_label "pout[1-2]"
power[2-3]_input Measured output power
temp[1-3]_input Measured temperature
temp[1-3]_crit Critical high temperature
temp[1-3]_crit_alarm Chip temperature critical high alarm
temp[1-3]_max Maximum temperature
temp[1-3]_max_alarm Chip temperature high alarm
...@@ -63,6 +63,15 @@ config SENSORS_IR38064 ...@@ -63,6 +63,15 @@ config SENSORS_IR38064
This driver can also be built as a module. If so, the module will This driver can also be built as a module. If so, the module will
be called ir38064. be called ir38064.
config SENSORS_ISL68137
tristate "Intersil ISL68137"
help
If you say yes here you get hardware monitoring support for Intersil
ISL68137.
This driver can also be built as a module. If so, the module will
be called isl68137.
config SENSORS_LM25066 config SENSORS_LM25066
tristate "National Semiconductor LM25066 and compatibles" tristate "National Semiconductor LM25066 and compatibles"
help help
......
...@@ -9,6 +9,7 @@ obj-$(CONFIG_SENSORS_ADM1275) += adm1275.o ...@@ -9,6 +9,7 @@ obj-$(CONFIG_SENSORS_ADM1275) += adm1275.o
obj-$(CONFIG_SENSORS_IBM_CFFPS) += ibm-cffps.o obj-$(CONFIG_SENSORS_IBM_CFFPS) += ibm-cffps.o
obj-$(CONFIG_SENSORS_IR35221) += ir35221.o obj-$(CONFIG_SENSORS_IR35221) += ir35221.o
obj-$(CONFIG_SENSORS_IR38064) += ir38064.o obj-$(CONFIG_SENSORS_IR38064) += ir38064.o
obj-$(CONFIG_SENSORS_ISL68137) += isl68137.o
obj-$(CONFIG_SENSORS_LM25066) += lm25066.o obj-$(CONFIG_SENSORS_LM25066) += lm25066.o
obj-$(CONFIG_SENSORS_LTC2978) += ltc2978.o obj-$(CONFIG_SENSORS_LTC2978) += ltc2978.o
obj-$(CONFIG_SENSORS_LTC3815) += ltc3815.o obj-$(CONFIG_SENSORS_LTC3815) += ltc3815.o
......
// SPDX-License-Identifier: GPL-2.0+
/*
* Hardware monitoring driver for Intersil ISL68137
*
* Copyright (c) 2017 Google Inc
*
*/
#include <linux/err.h>
#include <linux/hwmon-sysfs.h>
#include <linux/i2c.h>
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/string.h>
#include <linux/sysfs.h>
#include "pmbus.h"
#define ISL68137_VOUT_AVS 0x30
static ssize_t isl68137_avs_enable_show_page(struct i2c_client *client,
int page,
char *buf)
{
int val = pmbus_read_byte_data(client, page, PMBUS_OPERATION);
return sprintf(buf, "%d\n",
(val & ISL68137_VOUT_AVS) == ISL68137_VOUT_AVS ? 1 : 0);
}
static ssize_t isl68137_avs_enable_store_page(struct i2c_client *client,
int page,
const char *buf, size_t count)
{
int rc, op_val;
bool result;
rc = kstrtobool(buf, &result);
if (rc)
return rc;
op_val = result ? ISL68137_VOUT_AVS : 0;
/*
* Writes to VOUT setpoint over AVSBus will persist after the VRM is
* switched to PMBus control. Switching back to AVSBus control
* restores this persisted setpoint rather than re-initializing to
* PMBus VOUT_COMMAND. Writing VOUT_COMMAND first over PMBus before
* enabling AVS control is the workaround.
*/
if (op_val == ISL68137_VOUT_AVS) {
rc = pmbus_read_word_data(client, page, PMBUS_VOUT_COMMAND);
if (rc < 0)
return rc;
rc = pmbus_write_word_data(client, page, PMBUS_VOUT_COMMAND,
rc);
if (rc < 0)
return rc;
}
rc = pmbus_update_byte_data(client, page, PMBUS_OPERATION,
ISL68137_VOUT_AVS, op_val);
return (rc < 0) ? rc : count;
}
static ssize_t isl68137_avs_enable_show(struct device *dev,
struct device_attribute *devattr,
char *buf)
{
struct i2c_client *client = to_i2c_client(dev->parent);
struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
return isl68137_avs_enable_show_page(client, attr->index, buf);
}
static ssize_t isl68137_avs_enable_store(struct device *dev,
struct device_attribute *devattr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev->parent);
struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
return isl68137_avs_enable_store_page(client, attr->index, buf, count);
}
static SENSOR_DEVICE_ATTR_RW(avs0_enable, isl68137_avs_enable, 0);
static SENSOR_DEVICE_ATTR_RW(avs1_enable, isl68137_avs_enable, 1);
static struct attribute *enable_attrs[] = {
&sensor_dev_attr_avs0_enable.dev_attr.attr,
&sensor_dev_attr_avs1_enable.dev_attr.attr,
NULL,
};
static const struct attribute_group enable_group = {
.attrs = enable_attrs,
};
static const struct attribute_group *attribute_groups[] = {
&enable_group,
NULL,
};
static struct pmbus_driver_info isl68137_info = {
.pages = 2,
.format[PSC_VOLTAGE_IN] = direct,
.format[PSC_VOLTAGE_OUT] = direct,
.format[PSC_CURRENT_IN] = direct,
.format[PSC_CURRENT_OUT] = direct,
.format[PSC_POWER] = direct,
.format[PSC_TEMPERATURE] = direct,
.m[PSC_VOLTAGE_IN] = 1,
.b[PSC_VOLTAGE_IN] = 0,
.R[PSC_VOLTAGE_IN] = 3,
.m[PSC_VOLTAGE_OUT] = 1,
.b[PSC_VOLTAGE_OUT] = 0,
.R[PSC_VOLTAGE_OUT] = 3,
.m[PSC_CURRENT_IN] = 1,
.b[PSC_CURRENT_IN] = 0,
.R[PSC_CURRENT_IN] = 2,
.m[PSC_CURRENT_OUT] = 1,
.b[PSC_CURRENT_OUT] = 0,
.R[PSC_CURRENT_OUT] = 1,
.m[PSC_POWER] = 1,
.b[PSC_POWER] = 0,
.R[PSC_POWER] = 0,
.m[PSC_TEMPERATURE] = 1,
.b[PSC_TEMPERATURE] = 0,
.R[PSC_TEMPERATURE] = 0,
.func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_IIN | PMBUS_HAVE_PIN
| PMBUS_HAVE_STATUS_INPUT | PMBUS_HAVE_TEMP | PMBUS_HAVE_TEMP2
| PMBUS_HAVE_TEMP3 | PMBUS_HAVE_STATUS_TEMP
| PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT
| PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT | PMBUS_HAVE_POUT,
.func[1] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT
| PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT | PMBUS_HAVE_POUT,
.groups = attribute_groups,
};
static int isl68137_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
return pmbus_do_probe(client, id, &isl68137_info);
}
static const struct i2c_device_id isl68137_id[] = {
{"isl68137", 0},
{}
};
MODULE_DEVICE_TABLE(i2c, isl68137_id);
/* This is the driver that will be inserted */
static struct i2c_driver isl68137_driver = {
.driver = {
.name = "isl68137",
},
.probe = isl68137_probe,
.remove = pmbus_do_remove,
.id_table = isl68137_id,
};
module_i2c_driver(isl68137_driver);
MODULE_AUTHOR("Maxim Sloyko <maxims@google.com>");
MODULE_DESCRIPTION("PMBus driver for Intersil ISL68137");
MODULE_LICENSE("GPL");
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment