Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  powerpc: Fix system calls on Cell entered with XER.SO=1
  powerpc/cell: Fix GDB watchpoints, again
  powerpc/mpic: Don't reset affinity for secondary MPIC on boot
  powerpc/cell/axon-msi: Retry on missing interrupt
  powerpc: Fix boot freeze on machine with empty memory node
  powerpc: Fix IRQ assignment for some PCIe devices
  powerpc/spufs: Fix spinning in spufs_ps_fault on signal
  powerpc/mpc832x_rdb: fix swapped ethernet ids
  powerpc: Use generic PHY driver for Marvell 88E1111 PHY on GE Fanuc SBC610
  powerpc/85xx: L2 cache size wrong in 8572DS dts
  powerpc/virtex: Update defconfigs
  powerpc/52xx: update defconfigs
  xsysace: Fix driver to use resource_size_t instead of unsigned long
  powerpc/virtex: fix various format/casting printk mismatches
  powerpc/mpc5200: fix bestcomm Kconfig dependencies
  powerpc/44x: Fix 460EX/460GT machine check handling
  powerpc/40x: Limit allocable DRAM during early mapping

arch/powerpc/boot/dts/mpc832x_rdb.dts

@@ -18,8 +18,8 @@ / {
 	#size-cells = <1>;
 
 	aliases {
-		ethernet0 = &enet0;
-		ethernet1 = &enet1;
+		ethernet0 = &enet1;
+		ethernet1 = &enet0;
 		serial0 = &serial0;
 		serial1 = &serial1;
 		pci0 = &pci0;

arch/powerpc/boot/dts/mpc8572ds.dts

@@ -90,7 +90,7 @@ L2: l2-cache-controller@20000 {
 			compatible = "fsl,mpc8572-l2-cache-controller";
 			reg = <0x20000 0x1000>;
 			cache-line-size = <32>;	// 32 bytes
-			cache-size = <0x80000>;	// L2, 512K
+			cache-size = <0x100000>; // L2, 1M
 			interrupt-parent = <&mpic>;
 			interrupts = <16 2>;
 		};

arch/powerpc/configs/86xx/gef_sbc610_defconfig

@@ -838,7 +838,7 @@ CONFIG_PHYLIB=y
 #
 # MII PHY device drivers
 #
-CONFIG_MARVELL_PHY=y
+# CONFIG_MARVELL_PHY is not set
 # CONFIG_DAVICOM_PHY is not set
 # CONFIG_QSEMI_PHY is not set
 # CONFIG_LXT_PHY is not set

arch/powerpc/configs/ppc40x_defconfig

 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.28-rc2
-# Tue Oct 28 08:56:44 2008
+# Linux kernel version: 2.6.28-rc4
+# Fri Nov 14 09:54:44 2008
 #
 # CONFIG_PPC64 is not set
 
@@ -500,15 +500,17 @@ CONFIG_BLK_DEV_RAM_SIZE=35000
 # CONFIG_BLK_DEV_XIP is not set
 # CONFIG_CDROM_PKTCDVD is not set
 # CONFIG_ATA_OVER_ETH is not set
-# CONFIG_XILINX_SYSACE is not set
+CONFIG_XILINX_SYSACE=m
 # CONFIG_BLK_DEV_HD is not set
 CONFIG_MISC_DEVICES=y
 # CONFIG_PHANTOM is not set
 # CONFIG_EEPROM_93CX6 is not set
 # CONFIG_SGI_IOC4 is not set
 # CONFIG_TIFM_CORE is not set
+# CONFIG_ICS932S401 is not set
 # CONFIG_ENCLOSURE_SERVICES is not set
 # CONFIG_HP_ILO is not set
+# CONFIG_C2PORT is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -632,7 +634,13 @@ CONFIG_NETDEV_10000=y
 #
 # Hardware I/O ports
 #
-# CONFIG_SERIO is not set
+CONFIG_SERIO=m
+# CONFIG_SERIO_I8042 is not set
+# CONFIG_SERIO_SERPORT is not set
+# CONFIG_SERIO_PCIPS2 is not set
+# CONFIG_SERIO_LIBPS2 is not set
+# CONFIG_SERIO_RAW is not set
+CONFIG_SERIO_XILINX_XPS_PS2=m
 # CONFIG_GAMEPORT is not set
 
 #
@@ -660,7 +668,8 @@ CONFIG_SERIAL_8250_SHARE_IRQ=y
 #
 # Non-8250 serial port support
 #
-# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_UARTLITE=y
+CONFIG_SERIAL_UARTLITE_CONSOLE=y
 CONFIG_SERIAL_CORE=y
 CONFIG_SERIAL_CORE_CONSOLE=y
 # CONFIG_SERIAL_JSM is not set
@@ -756,6 +765,11 @@ CONFIG_GPIOLIB=y
 # CONFIG_DEBUG_GPIO is not set
 # CONFIG_GPIO_SYSFS is not set
 
+#
+# Memory mapped GPIO expanders:
+#
+CONFIG_GPIO_XILINX=y
+
 #
 # I2C GPIO expanders:
 #
@@ -776,11 +790,11 @@ CONFIG_GPIOLIB=y
 # CONFIG_HWMON is not set
 CONFIG_THERMAL=y
 # CONFIG_WATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
 
 #
 # Sonics Silicon Backplane
 #
-CONFIG_SSB_POSSIBLE=y
 # CONFIG_SSB is not set
 
 #
@@ -792,6 +806,7 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_TMIO is not set
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_REGULATOR is not set
 
 #
 # Multimedia devices
@@ -816,13 +831,65 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_DRM is not set
 # CONFIG_VGASTATE is not set
 CONFIG_VIDEO_OUTPUT_CONTROL=m
-# CONFIG_FB is not set
+CONFIG_FB=m
+# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_FB_DDC is not set
+# CONFIG_FB_BOOT_VESA_SUPPORT is not set
+CONFIG_FB_CFB_FILLRECT=m
+CONFIG_FB_CFB_COPYAREA=m
+CONFIG_FB_CFB_IMAGEBLIT=m
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+# CONFIG_FB_MODE_HELPERS is not set
+# CONFIG_FB_TILEBLITTING is not set
+
+#
+# Frame buffer hardware drivers
+#
+# CONFIG_FB_CIRRUS is not set
+# CONFIG_FB_PM2 is not set
+# CONFIG_FB_CYBER2000 is not set
+# CONFIG_FB_VGA16 is not set
+# CONFIG_FB_UVESA is not set
+# CONFIG_FB_S1D13XXX is not set
+# CONFIG_FB_NVIDIA is not set
+# CONFIG_FB_RIVA is not set
+# CONFIG_FB_MATROX is not set
+# CONFIG_FB_RADEON is not set
+# CONFIG_FB_ATY128 is not set
+# CONFIG_FB_ATY is not set
+# CONFIG_FB_S3 is not set
+# CONFIG_FB_SAVAGE is not set
+# CONFIG_FB_SIS is not set
+# CONFIG_FB_VIA is not set
+# CONFIG_FB_NEOMAGIC is not set
+# CONFIG_FB_KYRO is not set
+# CONFIG_FB_3DFX is not set
+# CONFIG_FB_VOODOO1 is not set
+# CONFIG_FB_VT8623 is not set
+# CONFIG_FB_TRIDENT is not set
+# CONFIG_FB_ARK is not set
+# CONFIG_FB_PM3 is not set
+# CONFIG_FB_CARMINE is not set
+# CONFIG_FB_IBM_GXT4500 is not set
+CONFIG_FB_XILINX=m
+# CONFIG_FB_VIRTUAL is not set
+# CONFIG_FB_METRONOME is not set
+# CONFIG_FB_MB862XX is not set
 # CONFIG_BACKLIGHT_LCD_SUPPORT is not set
 
 #
 # Display device support
 #
 # CONFIG_DISPLAY_SUPPORT is not set
+# CONFIG_LOGO is not set
 # CONFIG_SOUND is not set
 CONFIG_USB_SUPPORT=y
 CONFIG_USB_ARCH_HAS_HCD=y
@@ -851,6 +918,7 @@ CONFIG_USB_ARCH_HAS_EHCI=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_UIO is not set
 # CONFIG_STAGING is not set
+CONFIG_STAGING_EXCLUDE_BUILD=y
 
 #
 # File systems
@@ -1077,10 +1145,12 @@ CONFIG_DEBUG_BUGVERBOSE=y
 # CONFIG_FAULT_INJECTION is not set
 # CONFIG_LATENCYTOP is not set
 CONFIG_SYSCTL_SYSCALL_CHECK=y
-CONFIG_NOP_TRACER=y
-CONFIG_HAVE_FTRACE=y
-CONFIG_HAVE_DYNAMIC_FTRACE=y
-# CONFIG_FTRACE is not set
+CONFIG_HAVE_FUNCTION_TRACER=y
+
+#
+# Tracers
+#
+# CONFIG_FUNCTION_TRACER is not set
 # CONFIG_SCHED_TRACER is not set
 # CONFIG_CONTEXT_SWITCH_TRACER is not set
 # CONFIG_BOOT_TRACER is not set

arch/powerpc/configs/ppc44x_defconfig

 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.28-rc2
-# Tue Oct 28 09:28:58 2008
+# Linux kernel version: 2.6.28-rc4
+# Fri Nov 14 10:06:19 2008
 #
 # CONFIG_PPC64 is not set
 
@@ -506,15 +506,17 @@ CONFIG_BLK_DEV_RAM_SIZE=35000
 # CONFIG_BLK_DEV_XIP is not set
 # CONFIG_CDROM_PKTCDVD is not set
 # CONFIG_ATA_OVER_ETH is not set
-# CONFIG_XILINX_SYSACE is not set
+CONFIG_XILINX_SYSACE=m
 # CONFIG_BLK_DEV_HD is not set
 CONFIG_MISC_DEVICES=y
 # CONFIG_PHANTOM is not set
 # CONFIG_EEPROM_93CX6 is not set
 # CONFIG_SGI_IOC4 is not set
 # CONFIG_TIFM_CORE is not set
+# CONFIG_ICS932S401 is not set
 # CONFIG_ENCLOSURE_SERVICES is not set
 # CONFIG_HP_ILO is not set
+# CONFIG_C2PORT is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -680,7 +682,13 @@ CONFIG_NETDEV_10000=y
 #
 # Hardware I/O ports
 #
-# CONFIG_SERIO is not set
+CONFIG_SERIO=m
+# CONFIG_SERIO_I8042 is not set
+# CONFIG_SERIO_SERPORT is not set
+# CONFIG_SERIO_PCIPS2 is not set
+# CONFIG_SERIO_LIBPS2 is not set
+# CONFIG_SERIO_RAW is not set
+CONFIG_SERIO_XILINX_XPS_PS2=m
 # CONFIG_GAMEPORT is not set
 
 #
@@ -708,7 +716,8 @@ CONFIG_SERIAL_8250_SHARE_IRQ=y
 #
 # Non-8250 serial port support
 #
-# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_UARTLITE=y
+CONFIG_SERIAL_UARTLITE_CONSOLE=y
 CONFIG_SERIAL_CORE=y
 CONFIG_SERIAL_CORE_CONSOLE=y
 # CONFIG_SERIAL_JSM is not set
@@ -805,6 +814,11 @@ CONFIG_GPIOLIB=y
 # CONFIG_DEBUG_GPIO is not set
 # CONFIG_GPIO_SYSFS is not set
 
+#
+# Memory mapped GPIO expanders:
+#
+CONFIG_GPIO_XILINX=y
+
 #
 # I2C GPIO expanders:
 #
@@ -826,11 +840,11 @@ CONFIG_GPIOLIB=y
 # CONFIG_THERMAL is not set
 # CONFIG_THERMAL_HWMON is not set
 # CONFIG_WATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
 
 #
 # Sonics Silicon Backplane
 #
-CONFIG_SSB_POSSIBLE=y
 # CONFIG_SSB is not set
 
 #
@@ -842,6 +856,7 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_TMIO is not set
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_REGULATOR is not set
 
 #
 # Multimedia devices
@@ -866,13 +881,65 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_DRM is not set
 # CONFIG_VGASTATE is not set
 # CONFIG_VIDEO_OUTPUT_CONTROL is not set
-# CONFIG_FB is not set
+CONFIG_FB=m
+# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_FB_DDC is not set
+# CONFIG_FB_BOOT_VESA_SUPPORT is not set
+CONFIG_FB_CFB_FILLRECT=m
+CONFIG_FB_CFB_COPYAREA=m
+CONFIG_FB_CFB_IMAGEBLIT=m
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+# CONFIG_FB_MODE_HELPERS is not set
+# CONFIG_FB_TILEBLITTING is not set
+
+#
+# Frame buffer hardware drivers
+#
+# CONFIG_FB_CIRRUS is not set
+# CONFIG_FB_PM2 is not set
+# CONFIG_FB_CYBER2000 is not set
+# CONFIG_FB_VGA16 is not set
+# CONFIG_FB_UVESA is not set
+# CONFIG_FB_S1D13XXX is not set
+# CONFIG_FB_NVIDIA is not set
+# CONFIG_FB_RIVA is not set
+# CONFIG_FB_MATROX is not set
+# CONFIG_FB_RADEON is not set
+# CONFIG_FB_ATY128 is not set
+# CONFIG_FB_ATY is not set
+# CONFIG_FB_S3 is not set
+# CONFIG_FB_SAVAGE is not set
+# CONFIG_FB_SIS is not set
+# CONFIG_FB_VIA is not set
+# CONFIG_FB_NEOMAGIC is not set
+# CONFIG_FB_KYRO is not set
+# CONFIG_FB_3DFX is not set
+# CONFIG_FB_VOODOO1 is not set
+# CONFIG_FB_VT8623 is not set
+# CONFIG_FB_TRIDENT is not set
+# CONFIG_FB_ARK is not set
+# CONFIG_FB_PM3 is not set
+# CONFIG_FB_CARMINE is not set
+# CONFIG_FB_IBM_GXT4500 is not set
+CONFIG_FB_XILINX=m
+# CONFIG_FB_VIRTUAL is not set
+# CONFIG_FB_METRONOME is not set
+# CONFIG_FB_MB862XX is not set
 # CONFIG_BACKLIGHT_LCD_SUPPORT is not set
 
 #
 # Display device support
 #
 # CONFIG_DISPLAY_SUPPORT is not set
+# CONFIG_LOGO is not set
 # CONFIG_SOUND is not set
 CONFIG_USB_SUPPORT=y
 CONFIG_USB_ARCH_HAS_HCD=y
@@ -1002,6 +1069,7 @@ CONFIG_USB_STORAGE=m
 # CONFIG_DMADEVICES is not set
 # CONFIG_UIO is not set
 # CONFIG_STAGING is not set
+CONFIG_STAGING_EXCLUDE_BUILD=y
 
 #
 # File systems
@@ -1227,10 +1295,12 @@ CONFIG_DEBUG_BUGVERBOSE=y
 # CONFIG_FAULT_INJECTION is not set
 # CONFIG_LATENCYTOP is not set
 CONFIG_SYSCTL_SYSCALL_CHECK=y
-CONFIG_NOP_TRACER=y
-CONFIG_HAVE_FTRACE=y
-CONFIG_HAVE_DYNAMIC_FTRACE=y
-# CONFIG_FTRACE is not set
+CONFIG_HAVE_FUNCTION_TRACER=y
+
+#
+# Tracers
+#
+# CONFIG_FUNCTION_TRACER is not set
 # CONFIG_SCHED_TRACER is not set
 # CONFIG_CONTEXT_SWITCH_TRACER is not set
 # CONFIG_BOOT_TRACER is not set

arch/powerpc/kernel/cpu_setup_44x.S

@@ -34,7 +34,12 @@ _GLOBAL(__setup_cpu_440grx)
 	blr
 _GLOBAL(__setup_cpu_460ex)
 _GLOBAL(__setup_cpu_460gt)
-	b	__init_fpu_44x
+	mflr	r4
+	bl	__init_fpu_44x
+	bl	__fixup_440A_mcheck
+	mtlr	r4
+	blr
+
 _GLOBAL(__setup_cpu_440gx)
 _GLOBAL(__setup_cpu_440spe)
 	b	__fixup_440A_mcheck

arch/powerpc/kernel/entry_64.S

@@ -57,12 +57,18 @@ system_call_common:
 	beq-	1f
 	ld	r1,PACAKSAVE(r13)
 1:	std	r10,0(r1)
-	crclr	so
 	std	r11,_NIP(r1)
 	std	r12,_MSR(r1)
 	std	r0,GPR0(r1)
 	std	r10,GPR1(r1)
 	ACCOUNT_CPU_USER_ENTRY(r10, r11)
+	/*
+	 * This "crclr so" clears CR0.SO, which is the error indication on
+	 * return from this system call.  There must be no cmp instruction
+	 * between it and the "mfcr r9" below, otherwise if XER.SO is set,
+	 * CR0.SO will get set, causing all system calls to appear to fail.
+	 */
+	crclr	so
 	std	r2,GPR2(r1)
 	std	r3,GPR3(r1)
 	std	r4,GPR4(r1)

arch/powerpc/kernel/prom_parse.c

@@ -250,8 +250,11 @@ int of_irq_map_pci(struct pci_dev *pdev, struct of_irq *out_irq)
 	 * parsing
 	 */
 	dn = pci_device_to_OF_node(pdev);
-	if (dn)
-		return of_irq_map_one(dn, 0, out_irq);
+	if (dn) {
+		rc = of_irq_map_one(dn, 0, out_irq);
+		if (!rc)
+			return rc;
+	}
 
 	/* Ok, we don't, time to have fun. Let's start by building up an
 	 * interrupt spec.  we assume #interrupt-cells is 1, which is standard

arch/powerpc/mm/40x_mmu.c

@@ -93,7 +93,7 @@ void __init MMU_init_hw(void)
 
 unsigned long __init mmu_mapin_ram(void)
 {
-	unsigned long v, s;
+	unsigned long v, s, mapped;
 	phys_addr_t p;
 
 	v = KERNELBASE;
@@ -130,5 +130,17 @@ unsigned long __init mmu_mapin_ram(void)
 		s -= LARGE_PAGE_SIZE_4M;
 	}
 
-	return total_lowmem - s;
+	mapped = total_lowmem - s;
+
+	/* If the size of RAM is not an exact power of two, we may not
+	 * have covered RAM in its entirety with 16 and 4 MiB
+	 * pages. Consequently, restrict the top end of RAM currently
+	 * allocable so that calls to the LMB to allocate PTEs for "tail"
+	 * coverage with normal-sized pages (or other reasons) do not
+	 * attempt to allocate outside the allowed range.
+	 */
+
+	__initial_memory_limit_addr = memstart_addr + mapped;
+
+	return mapped;
 }

arch/powerpc/platforms/cell/smp.c

@@ -129,10 +129,15 @@ static int __init smp_iic_probe(void)
 	return cpus_weight(cpu_possible_map);
 }
 
-static void __devinit smp_iic_setup_cpu(int cpu)
+static void __devinit smp_cell_setup_cpu(int cpu)
 {
 	if (cpu != boot_cpuid)
 		iic_setup_cpu();
+
+	/*
+	 * change default DABRX to allow user watchpoints
+	 */
+	mtspr(SPRN_DABRX, DABRX_KERNEL | DABRX_USER);
 }
 
 static DEFINE_SPINLOCK(timebase_lock);
@@ -192,7 +197,7 @@ static struct smp_ops_t bpa_iic_smp_ops = {
 	.message_pass	= smp_iic_message_pass,
 	.probe		= smp_iic_probe,
 	.kick_cpu	= smp_cell_kick_cpu,
-	.setup_cpu	= smp_iic_setup_cpu,
+	.setup_cpu	= smp_cell_setup_cpu,
 	.cpu_bootable	= smp_cell_cpu_bootable,
 };
 

arch/powerpc/platforms/cell/spufs/file.c

@@ -390,6 +390,9 @@ static int spufs_ps_fault(struct vm_area_struct *vma,
 	if (offset >= ps_size)
 		return VM_FAULT_SIGBUS;
 
+	if (fatal_signal_pending(current))
+		return VM_FAULT_SIGBUS;
+
 	/*
 	 * Because we release the mmap_sem, the context may be destroyed while
 	 * we're in spu_wait. Grab an extra reference so it isn't destroyed

arch/powerpc/sysdev/xilinx_intc.c

@@ -107,8 +107,8 @@ xilinx_intc_init(struct device_node *np)
 	}
 	regs = ioremap(res.start, 32);
 
-	printk(KERN_INFO "Xilinx intc at 0x%08LX mapped to 0x%p\n",
-		res.start, regs);
+	printk(KERN_INFO "Xilinx intc at 0x%08llx mapped to 0x%p\n",
+		(unsigned long long) res.start, regs);
 
 	/* Setup interrupt controller */
 	out_be32(regs + XINTC_IER, 0); /* disable all irqs */