Commit 0518469d authored by Thomas Gleixner's avatar Thomas Gleixner

Merge branch 'fortglx/3.3/tip/timers/core' of...

Merge branch 'fortglx/3.3/tip/timers/core' of git://git.linaro.org/people/jstultz/linux into timers/core
parents 28a00184 f5a54dd7
......@@ -47,14 +47,12 @@ static struct clocksource cont_rotime = {
.rating = 300,
.read = read_cont_rotime,
.mask = CLOCKSOURCE_MASK(32),
.shift = 10,
.flags = CLOCK_SOURCE_IS_CONTINUOUS,
};
static int __init etrax_init_cont_rotime(void)
{
cont_rotime.mult = clocksource_khz2mult(100000, cont_rotime.shift);
clocksource_register(&cont_rotime);
clocksource_register_khz(&cont_rotime, 100000);
return 0;
}
arch_initcall(etrax_init_cont_rotime);
......
......@@ -93,7 +93,6 @@ static struct clocksource m68328_clk = {
.name = "timer",
.rating = 250,
.read = m68328_read_clk,
.shift = 20,
.mask = CLOCKSOURCE_MASK(32),
.flags = CLOCK_SOURCE_IS_CONTINUOUS,
};
......@@ -115,8 +114,7 @@ void hw_timer_init(void)
/* Enable timer 1 */
TCTL |= TCTL_TEN;
m68328_clk.mult = clocksource_hz2mult(TICKS_PER_JIFFY*HZ, m68328_clk.shift);
clocksource_register(&m68328_clk);
clocksource_register_hz(&m68328_clk, TICKS_PER_JIFFY*HZ);
}
/***************************************************************************/
......
......@@ -44,7 +44,6 @@ static struct clocksource clocksource_cf_dt = {
.rating = 200,
.read = cf_dt_get_cycles,
.mask = CLOCKSOURCE_MASK(32),
.shift = 20,
.flags = CLOCK_SOURCE_IS_CONTINUOUS,
};
......@@ -60,9 +59,7 @@ static int __init init_cf_dt_clocksource(void)
__raw_writeb(0x00, DTER0);
__raw_writel(0x00000000, DTRR0);
__raw_writew(DMA_DTMR_CLK_DIV_16 | DMA_DTMR_ENABLE, DTMR0);
clocksource_cf_dt.mult = clocksource_hz2mult(DMA_FREQ,
clocksource_cf_dt.shift);
return clocksource_register(&clocksource_cf_dt);
return clocksource_register_hz(&clocksource_cf_dt, DMA_FREQ);
}
arch_initcall(init_cf_dt_clocksource);
......
......@@ -144,7 +144,6 @@ static struct clocksource pit_clk = {
.name = "pit",
.rating = 100,
.read = pit_read_clk,
.shift = 20,
.mask = CLOCKSOURCE_MASK(32),
};
......@@ -162,8 +161,7 @@ void hw_timer_init(void)
setup_irq(MCFINT_VECBASE + MCFINT_PIT1, &pit_irq);
pit_clk.mult = clocksource_hz2mult(FREQ, pit_clk.shift);
clocksource_register(&pit_clk);
clocksource_register_hz(&pit_clk, FREQ);
}
/***************************************************************************/
......@@ -114,7 +114,6 @@ static struct clocksource mcfslt_clk = {
.name = "slt",
.rating = 250,
.read = mcfslt_read_clk,
.shift = 20,
.mask = CLOCKSOURCE_MASK(32),
.flags = CLOCK_SOURCE_IS_CONTINUOUS,
};
......@@ -136,8 +135,7 @@ void hw_timer_init(void)
setup_irq(MCF_IRQ_TIMER, &mcfslt_timer_irq);
mcfslt_clk.mult = clocksource_hz2mult(MCF_BUSCLK, mcfslt_clk.shift);
clocksource_register(&mcfslt_clk);
clocksource_register_hz(&mcfslt_clk, MCF_BUSCLK);
#ifdef CONFIG_HIGHPROFILE
mcfslt_profile_init();
......
......@@ -88,7 +88,6 @@ static struct clocksource mcftmr_clk = {
.name = "tmr",
.rating = 250,
.read = mcftmr_read_clk,
.shift = 20,
.mask = CLOCKSOURCE_MASK(32),
.flags = CLOCK_SOURCE_IS_CONTINUOUS,
};
......@@ -109,8 +108,7 @@ void hw_timer_init(void)
__raw_writew(MCFTIMER_TMR_ENORI | MCFTIMER_TMR_CLK16 |
MCFTIMER_TMR_RESTART | MCFTIMER_TMR_ENABLE, TA(MCFTIMER_TMR));
mcftmr_clk.mult = clocksource_hz2mult(FREQ, mcftmr_clk.shift);
clocksource_register(&mcftmr_clk);
clocksource_register_hz(&mcftmr_clk, FREQ);
setup_irq(MCF_IRQ_TIMER, &mcftmr_timer_irq);
......
......@@ -198,8 +198,6 @@ static struct clocksource clocksource_cr16 = {
.rating = 300,
.read = read_cr16,
.mask = CLOCKSOURCE_MASK(BITS_PER_LONG),
.mult = 0, /* to be set */
.shift = 22,
.flags = CLOCK_SOURCE_IS_CONTINUOUS,
};
......@@ -270,7 +268,5 @@ void __init time_init(void)
/* register at clocksource framework */
current_cr16_khz = PAGE0->mem_10msec/10; /* kHz */
clocksource_cr16.mult = clocksource_khz2mult(current_cr16_khz,
clocksource_cr16.shift);
clocksource_register(&clocksource_cr16);
clocksource_register_khz(&clocksource_cr16, current_cr16_khz);
}
......@@ -75,8 +75,6 @@ static struct clocksource itimer_clocksource = {
.rating = 300,
.read = itimer_read,
.mask = CLOCKSOURCE_MASK(64),
.mult = 1000,
.shift = 0,
.flags = CLOCK_SOURCE_IS_CONTINUOUS,
};
......@@ -94,9 +92,9 @@ static void __init setup_itimer(void)
clockevent_delta2ns(60 * HZ, &itimer_clockevent);
itimer_clockevent.min_delta_ns =
clockevent_delta2ns(1, &itimer_clockevent);
err = clocksource_register(&itimer_clocksource);
err = clocksource_register_hz(&itimer_clocksource, USEC_PER_SEC);
if (err) {
printk(KERN_ERR "clocksource_register returned %d\n", err);
printk(KERN_ERR "clocksource_register_hz returned %d\n", err);
return;
}
clockevents_register_device(&itimer_clockevent);
......
......@@ -15,7 +15,7 @@
#define CALIBRATE_TIME_MSEC 30 /* 30 msecs */
#define CALIBRATE_LATCH \
((CLOCK_TICK_RATE * CALIBRATE_TIME_MSEC + 1000/2)/1000)
((PIT_TICK_RATE * CALIBRATE_TIME_MSEC + 1000/2)/1000)
static inline void mach_prepare_counter(void)
{
......
......@@ -178,11 +178,11 @@ static unsigned long calc_pmtimer_ref(u64 deltatsc, u64 pm1, u64 pm2)
}
#define CAL_MS 10
#define CAL_LATCH (CLOCK_TICK_RATE / (1000 / CAL_MS))
#define CAL_LATCH (PIT_TICK_RATE / (1000 / CAL_MS))
#define CAL_PIT_LOOPS 1000
#define CAL2_MS 50
#define CAL2_LATCH (CLOCK_TICK_RATE / (1000 / CAL2_MS))
#define CAL2_LATCH (PIT_TICK_RATE / (1000 / CAL2_MS))
#define CAL2_PIT_LOOPS 5000
......
......@@ -41,14 +41,6 @@ static struct clocksource ccount_clocksource = {
.rating = 200,
.read = ccount_read,
.mask = CLOCKSOURCE_MASK(32),
/*
* With a shift of 22 the lower limit of the cpu clock is
* 1MHz, where NSEC_PER_CCOUNT is 1000 or a bit less than
* 2^10: Since we have 32 bits and the multiplicator can
* already take up as much as 10 bits, this leaves us with
* remaining upper 22 bits.
*/
.shift = 22,
};
static irqreturn_t timer_interrupt(int irq, void *dev_id);
......@@ -66,10 +58,7 @@ void __init time_init(void)
printk("%d.%02d MHz\n", (int)ccount_per_jiffy/(1000000/HZ),
(int)(ccount_per_jiffy/(10000/HZ))%100);
#endif
ccount_clocksource.mult =
clocksource_hz2mult(CCOUNT_PER_JIFFY * HZ,
ccount_clocksource.shift);
clocksource_register(&ccount_clocksource);
clocksource_register_hz(&ccount_clocksource, CCOUNT_PER_JIFFY * HZ);
/* Initialize the linux timer interrupt. */
......
......@@ -143,7 +143,7 @@ DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_LE,
#ifndef CONFIG_X86_64
#include <asm/mach_timer.h>
#define PMTMR_EXPECTED_RATE \
((CALIBRATE_LATCH * (PMTMR_TICKS_PER_SEC >> 10)) / (CLOCK_TICK_RATE>>10))
((CALIBRATE_LATCH * (PMTMR_TICKS_PER_SEC >> 10)) / (PIT_TICK_RATE>>10))
/*
* Some boards have the PMTMR running way too fast. We check
* the PMTMR rate against PIT channel 2 to catch these cases.
......
......@@ -53,7 +53,7 @@ static cycle_t i8253_read(struct clocksource *cs)
count |= inb_p(PIT_CH0) << 8;
/* VIA686a test code... reset the latch if count > max + 1 */
if (count > LATCH) {
if (count > PIT_LATCH) {
outb_p(0x34, PIT_MODE);
outb_p(PIT_LATCH & 0xff, PIT_CH0);
outb_p(PIT_LATCH >> 8, PIT_CH0);
......@@ -114,8 +114,8 @@ static void init_pit_timer(enum clock_event_mode mode,
case CLOCK_EVT_MODE_PERIODIC:
/* binary, mode 2, LSB/MSB, ch 0 */
outb_p(0x34, PIT_MODE);
outb_p(LATCH & 0xff , PIT_CH0); /* LSB */
outb_p(LATCH >> 8 , PIT_CH0); /* MSB */
outb_p(PIT_LATCH & 0xff , PIT_CH0); /* LSB */
outb_p(PIT_LATCH >> 8 , PIT_CH0); /* MSB */
break;
case CLOCK_EVT_MODE_SHUTDOWN:
......
......@@ -59,7 +59,6 @@ static struct clocksource clksrc = {
.rating = 200,
.read = tc_get_cycles,
.mask = CLOCKSOURCE_MASK(32),
.shift = 18,
.flags = CLOCK_SOURCE_IS_CONTINUOUS,
};
......@@ -256,7 +255,6 @@ static int __init tcb_clksrc_init(void)
best_divisor_idx = i;
}
clksrc.mult = clocksource_hz2mult(divided_rate, clksrc.shift);
printk(bootinfo, clksrc.name, CONFIG_ATMEL_TCB_CLKSRC_BLOCK,
divided_rate / 1000000,
......@@ -292,7 +290,7 @@ static int __init tcb_clksrc_init(void)
__raw_writel(ATMEL_TC_SYNC, tcaddr + ATMEL_TC_BCR);
/* and away we go! */
clocksource_register(&clksrc);
clocksource_register_hz(&clksrc, divided_rate);
/* channel 2: periodic and oneshot timer support */
setup_clkevents(tc, clk32k_divisor_idx);
......
......@@ -131,7 +131,7 @@ static inline s64 timekeeping_get_ns_raw(void)
/* calculate the delta since the last update_wall_time: */
cycle_delta = (cycle_now - clock->cycle_last) & clock->mask;
/* return delta convert to nanoseconds using ntp adjusted mult. */
/* return delta convert to nanoseconds. */
return clocksource_cyc2ns(cycle_delta, clock->mult, clock->shift);
}
......@@ -813,11 +813,11 @@ static void timekeeping_adjust(s64 offset)
* First we shift it down from NTP_SHIFT to clocksource->shifted nsecs.
*
* Note we subtract one in the shift, so that error is really error*2.
* This "saves" dividing(shifting) intererval twice, but keeps the
* (error > interval) comparision as still measuring if error is
* This "saves" dividing(shifting) interval twice, but keeps the
* (error > interval) comparison as still measuring if error is
* larger then half an interval.
*
* Note: It does not "save" on aggrivation when reading the code.
* Note: It does not "save" on aggravation when reading the code.
*/
error = timekeeper.ntp_error >> (timekeeper.ntp_error_shift - 1);
if (error > interval) {
......@@ -833,7 +833,7 @@ static void timekeeping_adjust(s64 offset)
* nanosecond, and store the amount rounded up into
* the error. This causes the likely below to be unlikely.
*
* The properfix is to avoid rounding up by using
* The proper fix is to avoid rounding up by using
* the high precision timekeeper.xtime_nsec instead of
* xtime.tv_nsec everywhere. Fixing this will take some
* time.
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment