Commit 06281d46 authored by John Youn's avatar John Youn Committed by Felipe Balbi

usb: dwc3: Add ENDXFER command polling

ENDXFER polling is available on version 3.10a and later of the
DWC_usb3 (USB 3.0) controller. With this feature, the software can poll
the CMDACT bit in the DEPCMD register after issuing an ENDXFER command.
This feature is enabled by writing GUCTL2[14].

This feature is NOT available on the DWC_usb31 (USB 3.1) IP.
Signed-off-by: default avatarJohn Youn <johnyoun@synopsys.com>
Signed-off-by: default avatarFelipe Balbi <felipe.balbi@linux.intel.com>
parent da605f5f
......@@ -704,6 +704,17 @@ static int dwc3_core_init(struct dwc3 *dwc)
break;
}
/*
* ENDXFER polling is available on version 3.10a and later of
* the DWC_usb3 controller. It is NOT available in the
* DWC_usb31 controller.
*/
if (!dwc3_is_usb31(dwc) && dwc->revision >= DWC3_REVISION_310A) {
reg = dwc3_readl(dwc->regs, DWC3_GUCTL2);
reg |= DWC3_GUCTL2_RST_ACTBITLATER;
dwc3_writel(dwc->regs, DWC3_GUCTL2, reg);
}
return 0;
err4:
......
......@@ -109,6 +109,7 @@
#define DWC3_GPRTBIMAP_HS1 0xc184
#define DWC3_GPRTBIMAP_FS0 0xc188
#define DWC3_GPRTBIMAP_FS1 0xc18c
#define DWC3_GUCTL2 0xc19c
#define DWC3_VER_NUMBER 0xc1a0
#define DWC3_VER_TYPE 0xc1a4
......@@ -288,6 +289,9 @@
#define DWC3_GFLADJ_30MHZ_SDBND_SEL (1 << 7)
#define DWC3_GFLADJ_30MHZ_MASK 0x3f
/* Global User Control Register 2 */
#define DWC3_GUCTL2_RST_ACTBITLATER (1 << 14)
/* Device Configuration Register */
#define DWC3_DCFG_DEVADDR(addr) ((addr) << 3)
#define DWC3_DCFG_DEVADDR_MASK DWC3_DCFG_DEVADDR(0x7f)
......
......@@ -2228,6 +2228,18 @@ static void dwc3_stop_active_transfer(struct dwc3 *dwc, u32 epnum, bool force)
*
* - Issue EndTransfer WITH CMDIOC bit set
* - Wait 100us
*
* As of IP version 3.10a of the DWC_usb3 IP, the controller
* supports a mode to work around the above limitation. The
* software can poll the CMDACT bit in the DEPCMD register
* after issuing a EndTransfer command. This mode is enabled
* by writing GUCTL2[14]. This polling is already done in the
* dwc3_send_gadget_ep_cmd() function so if the mode is
* enabled, the EndTransfer command will have completed upon
* returning from this function and we don't need to delay for
* 100us.
*
* This mode is NOT available on the DWC_usb31 IP.
*/
cmd = DWC3_DEPCMD_ENDTRANSFER;
......@@ -2239,7 +2251,9 @@ static void dwc3_stop_active_transfer(struct dwc3 *dwc, u32 epnum, bool force)
WARN_ON_ONCE(ret);
dep->resource_index = 0;
dep->flags &= ~DWC3_EP_BUSY;
udelay(100);
if (dwc3_is_usb31(dwc) || dwc->revision < DWC3_REVISION_310A)
udelay(100);
}
static void dwc3_stop_active_transfers(struct dwc3 *dwc)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment