Merge bk://linux.bkbits.net/linux-2.5

into hostme.bitkeeper.com:/ua/repos/l/linux-bt/bt-2.5

Documentation/networking/ewrk3.txt

@@ -24,6 +24,7 @@ sequences). To utilise this ability, you have to do 8 things:
     kernel with the ewrk3 configuration turned off and reboot.
     5) insmod ewrk3.o
           [Alan Cox: Changed this so you can insmod ewrk3.o irq=x io=y]
+          [Adam Kropelin: Multiple cards now supported by irq=x1,x2 io=y1,y2]
     6) run the net startup bits for your new eth?? interface manually 
     (usually /etc/rc.inet[12] at boot time). 
     7) enjoy!

drivers/char/keyboard.c

@@ -264,23 +264,34 @@ void kd_mksound(unsigned int hz, unsigned int ticks)
 /*
  * Setting the keyboard rate.
  */
+static inline unsigned int ms_to_jiffies(unsigned int ms) {
+	unsigned int j;
+
+	j = (ms * HZ + 500) / 1000;
+	return (j > 0) ? j : 1;
+}
+
 int kbd_rate(struct kbd_repeat *rep)
 {
-	struct list_head * node;
-
-	if (rep->rate < 0 || rep->delay < 0)
-		return -EINVAL;
+	struct list_head *node;
+	unsigned int d = 0;
+	unsigned int p = 0;
 
 	list_for_each(node,&kbd_handler.h_list) {
 		struct input_handle *handle = to_handle_h(node);
-		if (test_bit(EV_REP, handle->dev->evbit)) {
-			if (rep->rate > HZ) rep->rate = HZ;
-			handle->dev->rep[REP_PERIOD] = rep->rate ? (HZ / rep->rate) : 0;
-			handle->dev->rep[REP_DELAY] = rep->delay * HZ / 1000;
-			if (handle->dev->rep[REP_DELAY] < handle->dev->rep[REP_PERIOD])
-				handle->dev->rep[REP_DELAY] = handle->dev->rep[REP_PERIOD];
+		struct input_dev *dev = handle->dev;
+
+		if (test_bit(EV_REP, dev->evbit)) {
+			if (rep->delay > 0)
+				dev->rep[REP_DELAY] = ms_to_jiffies(rep->delay);
+			if (rep->period > 0)
+				dev->rep[REP_PERIOD] = ms_to_jiffies(rep->period);
+			d = dev->rep[REP_DELAY]  * 1000 / HZ;
+			p = dev->rep[REP_PERIOD] * 1000 / HZ;
 		}
 	}
+	rep->delay  = d;
+	rep->period = p;
 	return 0;
 }
 

drivers/char/vt_ioctl.c

@@ -430,6 +430,7 @@ int vt_ioctl(struct tty_struct *tty, struct file * file,
 	case KDKBDREP:
 	{
 		struct kbd_repeat kbrep;
+		int err;
 		
 		if (!capable(CAP_SYS_TTY_CONFIG))
 			return -EPERM;
@@ -437,8 +438,9 @@ int vt_ioctl(struct tty_struct *tty, struct file * file,
 		if (copy_from_user(&kbrep, (void *)arg,
 				   sizeof(struct kbd_repeat)))
 			return -EFAULT;
-		if ((i = kbd_rate( &kbrep )))
-			return i;
+		err = kbd_rate(&kbrep);
+		if (err)
+			return err;
 		if (copy_to_user((void *)arg, &kbrep,
 				 sizeof(struct kbd_repeat)))
 			return -EFAULT;

drivers/input/keyboard/atkbd.c

@@ -244,8 +244,9 @@ static int atkbd_command(struct atkbd *atkbd, unsigned char *param, int command)
 
 	while (atkbd->cmdcnt && timeout--) udelay(10);
 
-	for (i = 0; i < receive; i++)
-		param[i] = atkbd->cmdbuf[(receive - 1) - i];
+	if (param)
+		for (i = 0; i < receive; i++)
+			param[i] = atkbd->cmdbuf[(receive - 1) - i];
 
 	if (atkbd->cmdcnt) 
 		return (atkbd->cmdcnt = 0) - 1;

drivers/input/misc/uinput.c

@@ -49,7 +49,7 @@ static int uinput_dev_event(struct input_dev *dev, unsigned int type, unsigned i
 
 	udev = (struct uinput_device *)dev->private;
 
-	udev->head = (udev->head + 1) & 0xF;
+	udev->head = (udev->head + 1) % UINPUT_BUFFER_SIZE;
 	udev->buff[udev->head].type = type;
 	udev->buff[udev->head].code = code;
 	udev->buff[udev->head].value = value;
@@ -87,14 +87,14 @@ static int uinput_create_device(struct uinput_device *udev)
 
 	input_register_device(udev->dev);
 
-	udev->state |= UIST_CREATED;
+	set_bit(UIST_CREATED, &(udev->state));
 
 	return 0;
 }
 
 static int uinput_destroy_device(struct uinput_device *udev)
 {
-	if (!(udev->state & UIST_CREATED)) {
+	if (!test_bit(UIST_CREATED, &(udev->state))) {
 		printk(KERN_WARNING "%s: create the device first\n", UINPUT_NAME);
 		return -EINVAL;
 	}
@@ -135,6 +135,39 @@ static int uinput_open(struct inode *inode, struct file *file)
 	return -ENOMEM;
 }
 
+static int uinput_validate_absbits(struct input_dev *dev)
+{
+	unsigned int cnt;
+	int retval = 0;
+	
+	for (cnt = 0; cnt < ABS_MAX; cnt++) {
+		if (!test_bit(cnt, dev->absbit)) 
+			continue;
+		
+		if (/*!dev->absmin[cnt] || !dev->absmax[cnt] || */
+		    (dev->absmax[cnt] <= dev->absmin[cnt])) {
+			printk(KERN_DEBUG 
+				"%s: invalid abs[%02x] min:%d max:%d\n",
+				UINPUT_NAME, cnt, 
+				dev->absmin[cnt], dev->absmax[cnt]);
+			retval = -EINVAL;
+			break;
+		}
+
+		if ((dev->absflat[cnt] < dev->absmin[cnt]) ||
+		    (dev->absflat[cnt] > dev->absmax[cnt])) {
+			printk(KERN_DEBUG 
+				"%s: absflat[%02x] out of range: %d "
+				"(min:%d/max:%d)\n",
+				UINPUT_NAME, cnt, dev->absflat[cnt],
+				dev->absmin[cnt], dev->absmax[cnt]);
+			retval = -EINVAL;
+			break;
+		}
+	}
+	return retval;
+}
+
 static int uinput_alloc_device(struct file *file, const char *buffer, size_t count)
 {
 	struct uinput_user_dev	user_dev;
@@ -145,14 +178,17 @@ static int uinput_alloc_device(struct file *file, const char *buffer, size_t cou
 
 	retval = count;
 
+	udev = (struct uinput_device *)file->private_data;
+	dev = udev->dev;
+
 	if (copy_from_user(&user_dev, buffer, sizeof(struct uinput_user_dev))) {
 		retval = -EFAULT;
 		goto exit;
 	}
 
-	udev = (struct uinput_device *)file->private_data;
-	dev = udev->dev;
-
+	if (NULL != dev->name) 
+		kfree(dev->name);
+		
 	size = strnlen(user_dev.name, UINPUT_MAX_NAME_SIZE);
 	dev->name = kmalloc(size + 1, GFP_KERNEL);
 	if (!dev->name) {
@@ -168,7 +204,7 @@ static int uinput_alloc_device(struct file *file, const char *buffer, size_t cou
 	dev->id.version	= user_dev.id.version;
 	dev->ff_effects_max = user_dev.ff_effects_max;
 
-	size = sizeof(unsigned long) * NBITS(ABS_MAX + 1);
+	size = sizeof(int) * (ABS_MAX + 1);
 	memcpy(dev->absmax, user_dev.absmax, size);
 	memcpy(dev->absmin, user_dev.absmin, size);
 	memcpy(dev->absfuzz, user_dev.absfuzz, size);
@@ -177,33 +213,20 @@ static int uinput_alloc_device(struct file *file, const char *buffer, size_t cou
 	/* check if absmin/absmax/absfuzz/absflat are filled as
 	 * told in Documentation/input/input-programming.txt */
 	if (test_bit(EV_ABS, dev->evbit)) {
-		unsigned int cnt;
-		for (cnt = 1; cnt < ABS_MAX; cnt++)
-			if (test_bit(cnt, dev->absbit) &&
-					(!dev->absmin[cnt] ||
-					 !dev->absmax[cnt] ||
-					 !dev->absfuzz[cnt] ||
-					 !dev->absflat[cnt])) {
-				printk(KERN_DEBUG "%s: set abs fields "
-					"first\n", UINPUT_NAME);
-				retval = -EINVAL;
-				goto free_name;
-			}
+		retval = uinput_validate_absbits(dev);
+		if (retval < 0)
+			kfree(dev->name);
 	}
 
 exit:
 	return retval;
-free_name:
-	kfree(dev->name);
-	goto exit;
 }
 
 static int uinput_write(struct file *file, const char *buffer, size_t count, loff_t *ppos)
 {
 	struct uinput_device	*udev = file->private_data;
 	
-
-	if (udev->state & UIST_CREATED) {
+	if (test_bit(UIST_CREATED, &(udev->state))) {
 		struct input_event	ev;
 
 		if (copy_from_user(&ev, buffer, sizeof(struct input_event)))
@@ -220,23 +243,28 @@ static ssize_t uinput_read(struct file *file, char *buffer, size_t count, loff_t
 {
 	struct uinput_device *udev = file->private_data;
 	int retval = 0;
+	
+	if (!test_bit(UIST_CREATED, &(udev->state)))
+		return -ENODEV;
 
-	if (udev->head == udev->tail && (udev->state & UIST_CREATED) && (file->f_flags & O_NONBLOCK))
+	if ((udev->head == udev->tail) && (file->f_flags & O_NONBLOCK))
 		return -EAGAIN;
 
 	retval = wait_event_interruptible(udev->waitq,
-		udev->head != udev->tail && (udev->state & UIST_CREATED));
-
+			(udev->head != udev->tail) || 
+			!test_bit(UIST_CREATED, &(udev->state)));
+	
 	if (retval)
 		return retval;
 
-	if (!(udev->state & UIST_CREATED))
+	if (!test_bit(UIST_CREATED, &(udev->state)))
 		return -ENODEV;
 
-	while (udev->head != udev->tail && retval + sizeof(struct uinput_device) <= count) {
+	while ((udev->head != udev->tail) && 
+	    (retval + sizeof(struct uinput_device) <= count)) {
 		if (copy_to_user(buffer + retval, &(udev->buff[udev->tail]),
 		    sizeof(struct input_event))) return -EFAULT;
-		udev->tail = (udev->tail + 1) % (UINPUT_BUFFER_SIZE - 1);
+		udev->tail = (udev->tail + 1) % UINPUT_BUFFER_SIZE;
 		retval += sizeof(struct input_event);
 	}
 
@@ -245,7 +273,7 @@ static ssize_t uinput_read(struct file *file, char *buffer, size_t count, loff_t
 
 static unsigned int uinput_poll(struct file *file, poll_table *wait)
 {
-        struct uinput_device *udev = file->private_data;
+	struct uinput_device *udev = file->private_data;
 
 	poll_wait(file, &udev->waitq, wait);
 
@@ -257,7 +285,7 @@ static unsigned int uinput_poll(struct file *file, poll_table *wait)
 
 static int uinput_burn_device(struct uinput_device *udev)
 {
-	if (udev->state & UIST_CREATED)
+	if (test_bit(UIST_CREATED, &(udev->state)))
 		uinput_destroy_device(udev);
 
 	kfree(udev->dev);
@@ -282,50 +310,52 @@ static int uinput_ioctl(struct inode *inode, struct file *file, unsigned int cmd
 
 	udev = (struct uinput_device *)file->private_data;
 
-	if (cmd >= UI_SET_EVBIT && (udev->state & UIST_CREATED))
+	/* device attributes can not be changed after the device is created */
+	if (cmd >= UI_SET_EVBIT && test_bit(UIST_CREATED, &(udev->state)))
 		return -EINVAL;
 
 	switch (cmd) {
 		case UI_DEV_CREATE:
 			retval = uinput_create_device(udev);
-
 			break;
+			
 		case UI_DEV_DESTROY:
 			retval = uinput_destroy_device(udev);
-
 			break;
+
+
 		case UI_SET_EVBIT:
 			set_bit(arg, udev->dev->evbit);
-
-		break;
+			break;
+			
 		case UI_SET_KEYBIT:
 			set_bit(arg, udev->dev->keybit);
-
-		break;
+			break;
+			
 		case UI_SET_RELBIT:
 			set_bit(arg, udev->dev->relbit);
-
-		break;
+			break;
+			
 		case UI_SET_ABSBIT:
 			set_bit(arg, udev->dev->absbit);
-
-		break;
+			break;
+			
 		case UI_SET_MSCBIT:
 			set_bit(arg, udev->dev->mscbit);
-
-		break;
+			break;
+			
 		case UI_SET_LEDBIT:
 			set_bit(arg, udev->dev->ledbit);
-
-		break;
+			break;
+			
 		case UI_SET_SNDBIT:
 			set_bit(arg, udev->dev->sndbit);
-
-		break;
+			break;
+			
 		case UI_SET_FFBIT:
 			set_bit(arg, udev->dev->ffbit);
-
-		break;
+			break;
+			
 		default:
 			retval = -EFAULT;
 	}

drivers/input/serio/i8042.c

@@ -26,14 +26,16 @@ MODULE_DESCRIPTION("i8042 keyboard and mouse controller driver");
 MODULE_LICENSE("GPL");
 
 MODULE_PARM(i8042_noaux, "1i");
+MODULE_PARM(i8042_nomux, "1i");
 MODULE_PARM(i8042_unlock, "1i");
 MODULE_PARM(i8042_reset, "1i");
 MODULE_PARM(i8042_direct, "1i");
 MODULE_PARM(i8042_dumbkbd, "1i");
 
+static int i8042_reset;
 static int i8042_noaux;
+static int i8042_nomux;
 static int i8042_unlock;
-static int i8042_reset;
 static int i8042_direct;
 static int i8042_dumbkbd;
 
@@ -220,7 +222,6 @@ static int i8042_aux_write(struct serio *port, unsigned char c)
 	return retval;
 }
 
-
 /*
  * i8042_open() is called when a port is open by the higher layer.
  * It allocates the interrupt and enables in in the chip.
@@ -323,8 +324,8 @@ static struct serio i8042_aux_port =
 
 static struct i8042_values i8042_mux_values[4];
 static struct serio i8042_mux_port[4];
-static char i8042_mux_names[4][16];
-static char i8042_mux_short[4][8];
+static char i8042_mux_names[4][32];
+static char i8042_mux_short[4][16];
 static char i8042_mux_phys[4][32];
 
 /*
@@ -364,15 +365,15 @@ static void i8042_interrupt(int irq, void *dev_id, struct pt_regs *regs)
 		dfl = ((str & I8042_STR_PARITY) ? SERIO_PARITY : 0) |
 		      ((str & I8042_STR_TIMEOUT) ? SERIO_TIMEOUT : 0);
 
-		if (i8042_mux_values[0].exists && (buffer[i].str & I8042_STR_AUXDATA)) {
+		if (i8042_mux_values[0].exists && (str & I8042_STR_AUXDATA)) {
 
-			if (buffer[i].str & I8042_STR_MUXERR) {
-				switch (buffer[i].data) {
+			if (str & I8042_STR_MUXERR) {
+				switch (data) {
 					case 0xfd:
 					case 0xfe: dfl = SERIO_TIMEOUT; break;
 					case 0xff: dfl = SERIO_PARITY; break;
 				}
-				buffer[i].data = 0xfe;
+				data = 0xfe;
 			} else dfl = 0;
 
 			dbg("%02x <- i8042 (interrupt, aux%d, %d%s%s)",
@@ -380,8 +381,7 @@ static void i8042_interrupt(int irq, void *dev_id, struct pt_regs *regs)
 				dfl & SERIO_PARITY ? ", bad parity" : "",
 				dfl & SERIO_TIMEOUT ? ", timeout" : "");
 
-			if (i8042_mux_values[(str >> 6)].exists)
-				serio_interrupt(i8042_mux_port + (str >> 6), buffer[i].data, dfl);
+			serio_interrupt(i8042_mux_port + ((str >> 6) & 3), data, dfl);
 			continue;
 		}
 
@@ -390,8 +390,8 @@ static void i8042_interrupt(int irq, void *dev_id, struct pt_regs *regs)
 			dfl & SERIO_PARITY ? ", bad parity" : "",
 			dfl & SERIO_TIMEOUT ? ", timeout" : "");
 
-		if (i8042_aux_values.exists && (buffer[i].str & I8042_STR_AUXDATA)) {
-			serio_interrupt(&i8042_aux_port, buffer[i].data, dfl);
+		if (i8042_aux_values.exists && (str & I8042_STR_AUXDATA)) {
+			serio_interrupt(&i8042_aux_port, data, dfl);
 			continue;
 		}
 
@@ -602,8 +602,14 @@ static int __init i8042_check_mux(struct i8042_values *values)
 	if (i8042_command(&param, I8042_CMD_AUX_LOOP) || param == 0x5b)
 		return -1;
 
-	printk(KERN_INFO "i8042.c: Detected active multiplexing controller, rev%d.%d.\n",
-		~param >> 4, ~param & 0xf);
+	printk(KERN_INFO "i8042.c: Detected active multiplexing controller, rev %d.%d.\n",
+		(~param >> 4) & 0xf, ~param & 0xf);
+
+/*
+ * In MUX mode the keyboard translation seems to be always off.
+ */
+ 
+	i8042_direct = 1;
 
 /*
  * Disable all muxed ports by disabling AUX.
@@ -742,6 +748,12 @@ static int __init i8042_setup_reset(char *str)
 static int __init i8042_setup_noaux(char *str)
 {
 	i8042_noaux = 1;
+	i8042_nomux = 1;
+	return 1;
+}
+static int __init i8042_setup_nomux(char *str)
+{
+	i8042_nomux = 1;
 	return 1;
 }
 static int __init i8042_setup_unlock(char *str)
@@ -762,6 +774,7 @@ static int __init i8042_setup_dumbkbd(char *str)
 
 __setup("i8042_reset", i8042_setup_reset);
 __setup("i8042_noaux", i8042_setup_noaux);
+__setup("i8042_nomux", i8042_setup_nomux);
 __setup("i8042_unlock", i8042_setup_unlock);
 __setup("i8042_direct", i8042_setup_direct);
 __setup("i8042_dumbkbd", i8042_setup_dumbkbd);
@@ -796,6 +809,7 @@ static void __init i8042_init_mux_values(struct i8042_values *values, struct ser
 	sprintf(i8042_mux_short[index], "AUX%d", index);
 	port->name = i8042_mux_names[index];
 	port->phys = i8042_mux_phys[index];
+	port->driver = values;
 	values->name = i8042_mux_short[index];
 	values->mux = index;
 }
@@ -809,8 +823,8 @@ int __init i8042_init(void)
 	if (i8042_platform_init())
 		return -EBUSY;
 
-	i8042_aux_values.irq =	I8042_AUX_IRQ;
-	i8042_kbd_values.irq =	I8042_KBD_IRQ;
+	i8042_aux_values.irq = I8042_AUX_IRQ;
+	i8042_kbd_values.irq = I8042_KBD_IRQ;
 
 	if (i8042_controller_init())
 		return -ENODEV;
@@ -821,7 +835,7 @@ int __init i8042_init(void)
 	for (i = 0; i < 4; i++)
 		i8042_init_mux_values(i8042_mux_values + i, i8042_mux_port + i, i);
 
-	if (!i8042_noaux && !i8042_check_mux(&i8042_aux_values))
+	if (!i8042_nomux && !i8042_check_mux(&i8042_aux_values))
 		for (i = 0; i < 4; i++)
 			i8042_port_register(i8042_mux_values + i, i8042_mux_port + i);
 	else 

drivers/net/3c509.c

@@ -49,11 +49,13 @@
 			- Power Management support
 		v1.18c 1Mar2002 David Ruggiero <jdr@farfalle.com>
 			- Full duplex support
+		v1.19  16Oct2002 Zwane Mwaikambo <zwane@linuxpower.ca>
+			- Additional ethtool features
 */
 
 #define DRV_NAME	"3c509"
-#define DRV_VERSION	"1.18c"
-#define DRV_RELDATE	"1Mar2002"
+#define DRV_VERSION	"1.19"
+#define DRV_RELDATE	"16Oct2002"
 
 /* A few values that may be tweaked. */
 
@@ -140,9 +142,11 @@ enum RxFilter {
 #define TX_STATUS 	0x0B
 #define TX_FREE		0x0C		/* Remaining free bytes in Tx buffer. */
 
+#define WN0_CONF_CTRL	0x04		/* Window 0: Configuration control register */
+#define WN0_ADDR_CONF	0x06		/* Window 0: Address configuration register */
 #define WN0_IRQ		0x08		/* Window 0: Set IRQ line in bits 12-15. */
 #define WN4_MEDIA	0x0A		/* Window 4: Various transcvr/media bits. */
-#define  MEDIA_TP	0x00C0		/* Enable link beat and jabber for 10baseT. */
+#define	MEDIA_TP	0x00C0		/* Enable link beat and jabber for 10baseT. */
 #define WN4_NETDIAG	0x06		/* Window 4: Net diagnostic */
 #define FD_ENABLE	0x8000		/* Enable full-duplex ("external loopback") */  
 
@@ -981,6 +985,119 @@ el3_close(struct net_device *dev)
 	return 0;
 }
 
+static int 
+el3_link_ok(struct net_device *dev)
+{
+	int ioaddr = dev->base_addr;
+	u16 tmp;
+
+	EL3WINDOW(4);
+	tmp = inw(ioaddr + WN4_MEDIA);
+	EL3WINDOW(1);
+	return tmp & (1<<11);
+}
+
+static int
+el3_netdev_get_ecmd(struct net_device *dev, struct ethtool_cmd *ecmd)
+{
+	u16 tmp;
+	int ioaddr = dev->base_addr;
+	
+	EL3WINDOW(0);
+	/* obtain current tranceiver via WN4_MEDIA? */	
+	tmp = inw(ioaddr + WN0_ADDR_CONF);
+	ecmd->transceiver = XCVR_INTERNAL;
+	switch (tmp >> 14) {
+	case 0:
+		ecmd->port = PORT_TP;
+		break;
+	case 1:
+		ecmd->port = PORT_AUI;
+		ecmd->transceiver = XCVR_EXTERNAL;
+		break;
+	case 3:
+		ecmd->port = PORT_BNC;
+	default:
+		break;
+	}
+
+	ecmd->duplex = DUPLEX_HALF;
+	ecmd->supported = 0;
+	tmp = inw(ioaddr + WN0_CONF_CTRL);
+	if (tmp & (1<<13))
+		ecmd->supported |= SUPPORTED_AUI;
+	if (tmp & (1<<12))
+		ecmd->supported |= SUPPORTED_BNC;
+	if (tmp & (1<<9)) {
+		ecmd->supported |= SUPPORTED_TP | SUPPORTED_10baseT_Half |
+				SUPPORTED_10baseT_Full;	/* hmm... */
+		EL3WINDOW(4);
+		tmp = inw(ioaddr + WN4_NETDIAG);
+		if (tmp & FD_ENABLE)
+			ecmd->duplex = DUPLEX_FULL;
+	}
+
+	ecmd->speed = SPEED_10;
+	EL3WINDOW(1);
+	return 0;
+}
+
+static int
+el3_netdev_set_ecmd(struct net_device *dev, struct ethtool_cmd *ecmd)
+{
+	u16 tmp;
+	int ioaddr = dev->base_addr;
+
+	if (ecmd->speed != SPEED_10)
+		return -EINVAL;
+	if ((ecmd->duplex != DUPLEX_HALF) && (ecmd->duplex != DUPLEX_FULL))
+		return -EINVAL;
+	if ((ecmd->transceiver != XCVR_INTERNAL) && (ecmd->transceiver != XCVR_EXTERNAL))
+		return -EINVAL;
+
+	/* change XCVR type */
+	EL3WINDOW(0);
+	tmp = inw(ioaddr + WN0_ADDR_CONF);
+	switch (ecmd->port) {
+	case PORT_TP:
+		tmp &= ~(3<<14);
+		dev->if_port = 0;
+		break;
+	case PORT_AUI:
+		tmp |= (1<<14);
+		dev->if_port = 1;
+		break;
+	case PORT_BNC:
+		tmp |= (3<<14);
+		dev->if_port = 3;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	outw(tmp, ioaddr + WN0_ADDR_CONF);
+	if (dev->if_port == 3) {
+		/* fire up the DC-DC convertor if BNC gets enabled */
+		tmp = inw(ioaddr + WN0_ADDR_CONF);
+		if (tmp & (3 << 14)) {
+			outw(StartCoax, ioaddr + EL3_CMD);
+			udelay(800);
+		} else
+			return -EIO;
+	}
+
+	EL3WINDOW(4);
+	tmp = inw(ioaddr + WN4_NETDIAG);
+	if (ecmd->duplex == DUPLEX_FULL)
+		tmp |= FD_ENABLE;
+	else
+		tmp &= ~FD_ENABLE;
+	outw(tmp, ioaddr + WN4_NETDIAG);
+	EL3WINDOW(1);
+
+	return 0;
+}
+
 /**
  * netdev_ethtool_ioctl: Handle network interface SIOCETHTOOL ioctls
  * @dev: network interface on which out-of-band action is to be performed
@@ -989,9 +1106,11 @@ el3_close(struct net_device *dev)
  * Process the various commands of the SIOCETHTOOL interface.
  */
 
-static int netdev_ethtool_ioctl (struct net_device *dev, void *useraddr)
+static int
+netdev_ethtool_ioctl (struct net_device *dev, void *useraddr)
 {
 	u32 ethcmd;
+	struct el3_private *lp = dev->priv;
 
 	/* dev_ioctl() in ../../net/core/dev.c has already checked
 	   capable(CAP_NET_ADMIN), so don't bother with that here.  */
@@ -1010,6 +1129,41 @@ static int netdev_ethtool_ioctl (struct net_device *dev, void *useraddr)
 		return 0;
 	}
 
+	/* get settings */
+	case ETHTOOL_GSET: {
+		int ret;
+		struct ethtool_cmd ecmd = { ETHTOOL_GSET };
+		spin_lock_irq(&lp->lock);
+		ret = el3_netdev_get_ecmd(dev, &ecmd);
+		spin_unlock_irq(&lp->lock);
+		if (copy_to_user(useraddr, &ecmd, sizeof(ecmd)))
+			return -EFAULT;
+		return ret;
+	}
+
+	/* set settings */
+	case ETHTOOL_SSET: {
+		int ret;
+		struct ethtool_cmd ecmd;
+		if (copy_from_user(&ecmd, useraddr, sizeof(ecmd)))
+			return -EFAULT;
+		spin_lock_irq(&lp->lock);
+		ret = el3_netdev_set_ecmd(dev, &ecmd);
+		spin_unlock_irq(&lp->lock);
+		return ret;
+	}
+
+	/* get link status */
+	case ETHTOOL_GLINK: {
+		struct ethtool_value edata = { ETHTOOL_GLINK };
+		spin_lock_irq(&lp->lock);
+		edata.data = el3_link_ok(dev);
+		spin_unlock_irq(&lp->lock);
+		if (copy_to_user(useraddr, &edata, sizeof(edata)))
+			return -EFAULT;
+		return 0;
+	}
+
 	/* get message-level */
 	case ETHTOOL_GMSGLVL: {
 		struct ethtool_value edata = {ETHTOOL_GMSGLVL};
@@ -1043,7 +1197,8 @@ static int netdev_ethtool_ioctl (struct net_device *dev, void *useraddr)
  * Process the various out-of-band ioctls passed to this driver.
  */
 
-static int netdev_ioctl (struct net_device *dev, struct ifreq *rq, int cmd)
+static int
+netdev_ioctl (struct net_device *dev, struct ifreq *rq, int cmd)
 {
 	int rc = 0;
 
@@ -1060,7 +1215,8 @@ static int netdev_ioctl (struct net_device *dev, struct ifreq *rq, int cmd)
 	return rc;
 }
 
-static void el3_down(struct net_device *dev)
+static void
+el3_down(struct net_device *dev)
 {
 	int ioaddr = dev->base_addr;
 
@@ -1077,7 +1233,7 @@ static void el3_down(struct net_device *dev)
 		/* Turn off thinnet power.  Green! */
 		outw(StopCoax, ioaddr + EL3_CMD);
 	else if (dev->if_port == 0) {
-		/* Disable link beat and jabber, if_port may change ere next open(). */
+		/* Disable link beat and jabber, if_port may change here next open(). */
 		EL3WINDOW(4);
 		outw(inw(ioaddr + WN4_MEDIA) & ~MEDIA_TP, ioaddr + WN4_MEDIA);
 	}
@@ -1087,7 +1243,8 @@ static void el3_down(struct net_device *dev)
 	update_stats(dev);
 }
 
-static void el3_up(struct net_device *dev)
+static void
+el3_up(struct net_device *dev)
 {
 	int i, sw_info, net_diag;
 	int ioaddr = dev->base_addr;
@@ -1176,7 +1333,8 @@ static void el3_up(struct net_device *dev)
 /* Power Management support functions */
 #ifdef CONFIG_PM
 
-static int el3_suspend(struct pm_dev *pdev)
+static int
+el3_suspend(struct pm_dev *pdev)
 {
 	unsigned long flags;
 	struct net_device *dev;
@@ -1202,7 +1360,8 @@ static int el3_suspend(struct pm_dev *pdev)
 	return 0;
 }
 
-static int el3_resume(struct pm_dev *pdev)
+static int
+el3_resume(struct pm_dev *pdev)
 {
 	unsigned long flags;
 	struct net_device *dev;
@@ -1228,7 +1387,8 @@ static int el3_resume(struct pm_dev *pdev)
 	return 0;
 }
 
-static int el3_pm_callback(struct pm_dev *pdev, pm_request_t rqst, void *data)
+static int
+el3_pm_callback(struct pm_dev *pdev, pm_request_t rqst, void *data)
 {
 	switch (rqst) {
 		case PM_SUSPEND:

drivers/net/bonding.c

@@ -186,6 +186,11 @@
  *       also added text to distinguish type of load balancing (rr or xor)
  *     - change arp_ip_target module param from "1-12s" (array of 12 ptrs)
  *       to "s" (a single ptr)
+ *
+ * 2002/09/18 - Jay Vosburgh <fubar at us dot ibm dot com>
+ *     - Fixed up bond_check_dev_link() (and callers): removed some magic
+ *	 numbers, banished local MII_ defines, wrapped ioctl calls to
+ *	 prevent EFAULT errors
  */
 
 #include <linux/config.h>
@@ -228,15 +233,6 @@
 #define BOND_LINK_MON_INTERV	0
 #endif
 
-#undef  MII_LINK_UP
-#define MII_LINK_UP	0x04
-
-#undef  MII_ENDOF_NWAY
-#define MII_ENDOF_NWAY	0x20
-
-#undef  MII_LINK_READY
-#define MII_LINK_READY	(MII_LINK_UP)
-
 #ifndef BOND_LINK_ARP_INTERV
 #define BOND_LINK_ARP_INTERV	0
 #endif
@@ -386,13 +382,25 @@ static slave_t *bond_detach_slave(bonding_t *bond, slave_t *slave)
 	return slave;
 }
 
+/*
+ * Less bad way to call ioctl from within the kernel; this needs to be
+ * done some other way to get the call out of interrupt context.
+ * Needs "ioctl" variable to be supplied by calling context.
+ */
+#define IOCTL(dev, arg, cmd) ({		\
+	int ret;			\
+	mm_segment_t fs = get_fs();	\
+	set_fs(get_ds());		\
+	ret = ioctl(dev, arg, cmd);	\
+	set_fs(fs);			\
+	ret; })
+
 /* 
- * if <dev> supports MII link status reporting, check its link
- * and report it as a bit field in a short int :
- *   - 0x04 means link is up,
- *   - 0x20 means end of autonegociation
- * If the device doesn't support MII, then we only report 0x24,
- * meaning that the link is up and running since we can't check it.
+ * if <dev> supports MII link status reporting, check its link status.
+ *
+ * Return either BMSR_LSTATUS, meaning that the link is up (or we
+ * can't tell and just pretend it is), or 0, meaning that the link is
+ * down.
  */
 static u16 bond_check_dev_link(struct net_device *dev)
 {
@@ -401,7 +409,8 @@ static u16 bond_check_dev_link(struct net_device *dev)
 	struct mii_ioctl_data *mii;
 	struct ethtool_value etool;
 
-	if ((ioctl = dev->do_ioctl) != NULL)  { /* ioctl to access MII */
+	ioctl = dev->do_ioctl;
+	if (ioctl) {
 		/* TODO: set pointer to correct ioctl on a per team member */
 		/*       bases to make this more efficient. that is, once  */
 		/*       we determine the correct ioctl, we will always    */
@@ -415,9 +424,9 @@ static u16 bond_check_dev_link(struct net_device *dev)
 		/* effect...                                               */
 	        etool.cmd = ETHTOOL_GLINK;
 	        ifr.ifr_data = (char*)&etool;
-		if (ioctl(dev, &ifr, SIOCETHTOOL) == 0) {
+		if (IOCTL(dev, &ifr, SIOCETHTOOL) == 0) {
 			if (etool.data == 1) {
-				return(MII_LINK_READY);
+				return BMSR_LSTATUS;
 			} 
 			else { 
 				return(0);
@@ -431,21 +440,17 @@ static u16 bond_check_dev_link(struct net_device *dev)
 
 		/* Yes, the mii is overlaid on the ifreq.ifr_ifru */
 		mii = (struct mii_ioctl_data *)&ifr.ifr_data;
-		if (ioctl(dev, &ifr, SIOCGMIIPHY) != 0) {
-			return MII_LINK_READY;	 /* can't tell */
+		if (IOCTL(dev, &ifr, SIOCGMIIPHY) != 0) {
+			return BMSR_LSTATUS;	 /* can't tell */
 		}
 
-		mii->reg_num = 1;
-		if (ioctl(dev, &ifr, SIOCGMIIREG) == 0) {
-			/*
-			 * mii->val_out contains MII reg 1, BMSR
-			 * 0x0004 means link established
-			 */
-			return mii->val_out;
+		mii->reg_num = MII_BMSR;
+		if (IOCTL(dev, &ifr, SIOCGMIIREG) == 0) {
+			return mii->val_out & BMSR_LSTATUS;
 		}
 
 	}
-	return MII_LINK_READY;  /* spoof link up ( we can't check it) */
+	return BMSR_LSTATUS;  /* spoof link up ( we can't check it) */
 }
 
 static u16 bond_check_mii_link(bonding_t *bond)
@@ -459,7 +464,7 @@ static u16 bond_check_mii_link(bonding_t *bond)
 	read_unlock(&bond->ptrlock);
 	read_unlock_irqrestore(&bond->lock, flags);
 
-	return (has_active_interface ? MII_LINK_READY : 0);
+	return (has_active_interface ? BMSR_LSTATUS : 0);
 }
 
 static int bond_open(struct net_device *dev)
@@ -797,8 +802,8 @@ static int bond_enslave(struct net_device *master_dev,
 	new_slave->link_failure_count = 0;
 
 	/* check for initial state */
-	if ((miimon <= 0) || ((bond_check_dev_link(slave_dev) & MII_LINK_READY)
-		 == MII_LINK_READY)) {
+	if ((miimon <= 0) ||
+	    (bond_check_dev_link(slave_dev) == BMSR_LSTATUS)) {
 #ifdef BONDING_DEBUG
 		printk(KERN_CRIT "Initial state of slave_dev is BOND_LINK_UP\n");
 #endif
@@ -1220,7 +1225,7 @@ static void bond_mii_monitor(struct net_device *master)
 
 		switch (slave->link) {
 		case BOND_LINK_UP:	/* the link was up */
-			if ((link_state & MII_LINK_UP) == MII_LINK_UP) {
+			if (link_state == BMSR_LSTATUS) {
 				/* link stays up, tell that this one
 				   is immediately available */
 				if (IS_UP(dev) && (mindelay > -2)) {
@@ -1256,7 +1261,7 @@ static void bond_mii_monitor(struct net_device *master)
 			   ensure proper action to be taken
 			*/
 		case BOND_LINK_FAIL:	/* the link has just gone down */
-			if ((link_state & MII_LINK_UP) == 0) {
+			if (link_state != BMSR_LSTATUS) {
 				/* link stays down */
 				if (slave->delay <= 0) {
 					/* link down for too long time */
@@ -1285,7 +1290,7 @@ static void bond_mii_monitor(struct net_device *master)
 				} else {
 					slave->delay--;
 				}
-			} else if ((link_state & MII_LINK_READY) == MII_LINK_READY) {
+			} else {
 				/* link up again */
 				slave->link  = BOND_LINK_UP;
 				printk(KERN_INFO
@@ -1304,7 +1309,7 @@ static void bond_mii_monitor(struct net_device *master)
 			}
 			break;
 		case BOND_LINK_DOWN:	/* the link was down */
-			if ((link_state & MII_LINK_READY) != MII_LINK_READY) {
+			if (link_state != BMSR_LSTATUS) {
 				/* the link stays down, nothing more to do */
 				break;
 			} else {	/* link going up */
@@ -1326,7 +1331,7 @@ static void bond_mii_monitor(struct net_device *master)
 			   case there's something to do.
 			*/
 		case BOND_LINK_BACK:	/* the link has just come back */
-			if ((link_state & MII_LINK_UP) == 0) {
+			if (link_state != BMSR_LSTATUS) {
 				/* link down again */
 				slave->link  = BOND_LINK_DOWN;
 				printk(KERN_INFO
@@ -1335,8 +1340,7 @@ static void bond_mii_monitor(struct net_device *master)
 					master->name,
 					(updelay - slave->delay) * miimon,
 					dev->name);
-			}
-			else if ((link_state & MII_LINK_READY) == MII_LINK_READY) {
+			} else {
 				/* link stays up */
 				if (slave->delay == 0) {
 					/* now the link has been up for long time enough */
@@ -2110,7 +2114,7 @@ static int bond_get_info(char *buf, char **start, off_t offset, int length)
 
 		len += sprintf(buf + len, "MII Status: ");
 		len += sprintf(buf + len, 
-				link == MII_LINK_READY ? "up\n" : "down\n");
+				link == BMSR_LSTATUS ? "up\n" : "down\n");
 		len += sprintf(buf + len, "MII Polling Interval (ms): %d\n", 
 				miimon);
 		len += sprintf(buf + len, "Up Delay (ms): %d\n", updelay);

drivers/net/e1000/e1000_main.c

@@ -135,7 +135,7 @@ static int e1000_init_module(void);
 static void e1000_exit_module(void);
 static int e1000_probe(struct pci_dev *pdev, const struct pci_device_id *ent);
 static void e1000_remove(struct pci_dev *pdev);
-static void e1000_sw_init(struct e1000_adapter *adapter);
+static int e1000_sw_init(struct e1000_adapter *adapter);
 static int e1000_open(struct net_device *netdev);
 static int e1000_close(struct net_device *netdev);
 static int e1000_setup_tx_resources(struct e1000_adapter *adapter);
@@ -415,7 +415,8 @@ e1000_probe(struct pci_dev *pdev,
 
 	/* setup the private structure */
 
-	e1000_sw_init(adapter);
+	if(e1000_sw_init(adapter))
+		goto err_sw_init;
 
 	if(adapter->hw.mac_type >= e1000_82543) {
 		netdev->features = NETIF_F_SG |
@@ -500,6 +501,7 @@ e1000_probe(struct pci_dev *pdev,
 	cards_found++;
 	return 0;
 
+err_sw_init:
 err_eeprom:
 	iounmap(adapter->hw.hw_addr);
 err_ioremap:
@@ -555,7 +557,7 @@ e1000_remove(struct pci_dev *pdev)
  * OS network device settings (MTU size).
  **/
 
-static void __devinit
+static int __devinit
 e1000_sw_init(struct e1000_adapter *adapter)
 {
 	struct e1000_hw *hw = &adapter->hw;
@@ -564,11 +566,11 @@ e1000_sw_init(struct e1000_adapter *adapter)
 
 	/* PCI config space info */
 
-	pci_read_config_word(pdev, PCI_VENDOR_ID, &hw->vendor_id);
-	pci_read_config_word(pdev, PCI_DEVICE_ID, &hw->device_id);
-	pci_read_config_word(pdev, PCI_SUBSYSTEM_VENDOR_ID, 
-	                     &hw->subsystem_vendor_id);
-	pci_read_config_word(pdev, PCI_SUBSYSTEM_ID, &hw->subsystem_id);
+	hw->vendor_id = pdev->vendor;
+	hw->device_id = pdev->device;
+	hw->subsystem_vendor_id = pdev->subsystem_vendor;
+	hw->subsystem_id = pdev->subsystem_device;
+
 	pci_read_config_byte(pdev, PCI_REVISION_ID, &hw->revision_id);
 	pci_read_config_word(pdev, PCI_COMMAND, &hw->pci_cmd_word);
 
@@ -581,7 +583,7 @@ e1000_sw_init(struct e1000_adapter *adapter)
 
 	if (e1000_set_mac_type(hw)) {
 		E1000_ERR("Unknown MAC Type\n");
-		BUG();
+		return -1;
 	}
 
 	/* flow control settings */
@@ -622,6 +624,8 @@ e1000_sw_init(struct e1000_adapter *adapter)
 
 	atomic_set(&adapter->irq_sem, 1);
 	spin_lock_init(&adapter->stats_lock);
+
+	return 0;
 }
 
 /**

drivers/net/ewrk3.c

@@ -76,6 +76,7 @@
    kernel with the ewrk3 configuration turned off and reboot.
    5) insmod ewrk3.o
    [Alan Cox: Changed this so you can insmod ewrk3.o irq=x io=y]
+   [Adam Kropelin: now accepts irq=x1,x2 io=y1,y2 for multiple cards]
    6) run the net startup bits for your new eth?? interface manually
    (usually /etc/rc.inet[12] at boot time).
    7) enjoy!
@@ -130,10 +131,12 @@
    Add new multicasting code.
    0.41    20-Jan-96   Fix IRQ set up problem reported by
    <kenneth@bbs.sas.ntu.ac.sg>.
-   0.42    22-Apr-96      Fix alloc_device() bug <jari@markkus2.fimr.fi>
-   0.43    16-Aug-96      Update alloc_device() to conform to de4x5.c
-   0.44    08-Nov-01      use library crc32 functions <Matt_Domsch@dell.com>
-   0.45	   19-Jul-02	  fix unaligned access on alpha <martin@bruli.net>
+   0.42    22-Apr-96   Fix alloc_device() bug <jari@markkus2.fimr.fi>
+   0.43    16-Aug-96   Update alloc_device() to conform to de4x5.c
+   0.44    08-Nov-01   use library crc32 functions <Matt_Domsch@dell.com>
+   0.45    19-Jul-02   fix unaligned access on alpha <martin@bruli.net>
+   0.46    10-Oct-02   cli/sti removal <VDA@port.imtp.ilyichevsk.odessa.ua>
+   Multiple NIC support when module <akropel1@rochester.rr.com>
 
    =========================================================================
  */
@@ -167,7 +170,7 @@
 #include "ewrk3.h"
 
 static char version[] __initdata =
-"ewrk3.c:v0.43a 2001/02/04 davies@maniac.ultranet.com\n";
+"ewrk3.c:v0.46 2002/10/09 davies@maniac.ultranet.com\n";
 
 #ifdef EWRK3_DEBUG
 static int ewrk3_debug = EWRK3_DEBUG;
@@ -196,6 +199,7 @@ static int ewrk3_debug = 1;
 #define EWRK3_IOP_INC 0x20	/* I/O address increment */
 #define EWRK3_TOTAL_SIZE 0x20	/* required I/O address length */
 
+/* If you change this, remember to also change MODULE_PARM array limits */
 #ifndef MAX_NUM_EWRK3S
 #define MAX_NUM_EWRK3S 21
 #endif
@@ -1716,6 +1720,11 @@ static int ewrk3_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
 		break;
 	case EWRK3_SET_MCA:	/* Set a multicast address */
 		if (capable(CAP_NET_ADMIN)) {
+			if (ioc->len > 1024)
+			{
+				status = -EINVAL;
+				break;
+			}
 			if (copy_from_user(tmp->addr, ioc->data, ETH_ALEN * ioc->len)) {
 				status = -EFAULT;
 				break;
@@ -1843,35 +1852,62 @@ static int ewrk3_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
 }
 
 #ifdef MODULE
-static struct net_device thisEthwrk;
-static int io = 0x300;		/* <--- EDIT THESE LINES FOR YOUR CONFIGURATION */
-static int irq = 5;		/* or use the insmod io= irq= options           */
+static struct net_device *ewrk3_devs[MAX_NUM_EWRK3S];
+static int ndevs;
+static int io[MAX_NUM_EWRK3S+1] = { 0x300, 0, };		/* <--- EDIT THESE LINES FOR YOUR CONFIGURATION */
+static int irq[MAX_NUM_EWRK3S+1] = { 5, 0, };		/* or use the insmod io= irq= options           */
 
-MODULE_PARM(io, "i");
-MODULE_PARM(irq, "i");
-MODULE_PARM_DESC(io, "EtherWORKS 3 I/O base address");
-MODULE_PARM_DESC(irq, "EtherWORKS 3 IRQ number");
+/* '21' below should really be 'MAX_NUM_EWRK3S' */
+MODULE_PARM(io, "0-21i");
+MODULE_PARM(irq, "0-21i");
+MODULE_PARM_DESC(io, "EtherWORKS 3 I/O base address(es)");
+MODULE_PARM_DESC(irq, "EtherWORKS 3 IRQ number(s)");
 
 int init_module(void)
 {
-	thisEthwrk.base_addr = io;
-	thisEthwrk.irq = irq;
-	thisEthwrk.init = ewrk3_probe;
-	if (register_netdev(&thisEthwrk) != 0)
-		return -EIO;
-	return 0;
+	int i=0;
+
+	while( io[i] && irq[i] ) {
+		ewrk3_devs[ndevs] = kmalloc(sizeof(struct net_device), GFP_KERNEL);
+		if (!ewrk3_devs[ndevs])
+			goto error; 
+		memset(ewrk3_devs[ndevs], 0, sizeof(struct net_device));
+		ewrk3_devs[ndevs]->base_addr = io[i];
+		ewrk3_devs[ndevs]->irq = irq[i];
+		ewrk3_devs[ndevs]->init = ewrk3_probe;
+
+		if (register_netdev(ewrk3_devs[ndevs]) == 0)
+			ndevs++;
+		else
+			kfree(ewrk3_devs[ndevs]);
+
+		i++;
+	}
+
+	return ndevs ? 0 : -EIO;
+
+error:
+	cleanup_module();
+	return -ENOMEM;
 }
 
 void cleanup_module(void)
 {
-	unregister_netdev(&thisEthwrk);
-	if (thisEthwrk.priv) {
-		kfree(thisEthwrk.priv);
-		thisEthwrk.priv = NULL;
-	}
-	thisEthwrk.irq = 0;
+	int i;
+
+	for( i=0; i<ndevs; i++ )
+	{
+		unregister_netdev(ewrk3_devs[i]);
+		if (ewrk3_devs[i]->priv) {
+			kfree(ewrk3_devs[i]->priv);
+			ewrk3_devs[i]->priv = NULL;
+		}
+		ewrk3_devs[i]->irq = 0;
 
-	release_region(thisEthwrk.base_addr, EWRK3_TOTAL_SIZE);
+		release_region(ewrk3_devs[i]->base_addr, EWRK3_TOTAL_SIZE);
+		kfree(ewrk3_devs[i]);
+		ewrk3_devs[i] = NULL;
+	}
 }
 #endif				/* MODULE */
 MODULE_LICENSE("GPL");

drivers/net/irda/Config.help

@@ -55,12 +55,22 @@ CONFIG_NSC_FIR
   <file:Documentation/modules.txt>.  The module will be called
   nsc-ircc.o.
 
-CONFIG_TOSHIBA_FIR
+CONFIG_TOSHIBA_OLD
   Say Y here if you want to build support for the Toshiba Type-O IR
   chipset.  This chipset is used by the Toshiba Libretto 100CT, and
-  many more laptops.  If you want to compile it as a module, say M
-  here and read <file:Documentation/modules.txt>.  The module will be
-  called toshoboe.o.
+  many more laptops. This driver is obsolete, will no more be
+  maintained and will be removed in favor of the new driver.
+  If you want to compile it as a module, say M here and read
+  <file:Documentation/modules.txt>.
+  The module will be called toshoboe.o.
+
+CONFIG_TOSHIBA_FIR
+  Say Y here if you want to build support for the Toshiba Type-O IR
+  and Donau oboe chipsets. These chipsets are used by the Toshiba
+  Libretto 100/110CT, Tecra 8100, Portege 7020 and many more laptops.
+  If you want to compile it as a module, say M here and read
+  <file:Documentation/modules.txt>.
+  The module will be called donauboe.o.
 
 CONFIG_SMC_IRCC_FIR
   Say Y here if you want to build support for the SMC Infrared
@@ -165,3 +175,18 @@ CONFIG_ACT200L_DONGLE
   the normal 9-pin serial port connector, and can currently only be
   used by IrTTY. To activate support for ACTiSYS IR-200L dongles
   you will have to start irattach like this: "irattach -d act200l".
+
+Mobile Action MA600 dongle (Experimental)
+CONFIG_MA600_DONGLE
+  Say Y here if you want to build support for the Mobile Action MA600
+  dongle.  If you want to compile it as a module, say M here and read
+  <file:Documentation/modules.txt>.  The MA600 dongle attaches to
+  the normal 9-pin serial port connector, and can currently only be
+  tested on IrCOMM.  To activate support for MA600 dongles you will
+  have to insert "irattach -d ma600" in the /etc/irda/drivers script.
+  Note: irutils 0.9.15 requires no modification. irutils 0.9.9 needs
+  modification. For more information, download the following tar gzip
+  file.
+
+  There is a pre-compiled module on
+  <http://engsvr.ust.hk/~eetwl95/download/ma600-2.4.x.tar.gz>

drivers/net/irda/Config.in

@@ -28,6 +28,7 @@ comment 'FIR device drivers'
 dep_tristate 'IrDA USB dongles (EXPERIMENTAL)' CONFIG_USB_IRDA $CONFIG_IRDA $CONFIG_USB $CONFIG_EXPERIMENTAL
 dep_tristate 'NSC PC87108/PC87338' CONFIG_NSC_FIR  $CONFIG_IRDA
 dep_tristate 'Winbond W83977AF (IR)' CONFIG_WINBOND_FIR $CONFIG_IRDA
+dep_tristate 'Toshiba Type-O IR Port (old driver)' CONFIG_TOSHIBA_OLD $CONFIG_IRDA
 dep_tristate 'Toshiba Type-O IR Port' CONFIG_TOSHIBA_FIR $CONFIG_IRDA
 if [ "$CONFIG_EXPERIMENTAL" != "n" ]; then
 dep_tristate 'SMC IrCC (EXPERIMENTAL)' CONFIG_SMC_IRCC_FIR $CONFIG_IRDA

drivers/net/irda/Makefile

@@ -13,7 +13,8 @@ obj-$(CONFIG_USB_IRDA)		+= irda-usb.o
 obj-$(CONFIG_NSC_FIR)		+= nsc-ircc.o
 obj-$(CONFIG_WINBOND_FIR)	+= w83977af_ir.o
 obj-$(CONFIG_SA1100_FIR)	+= sa1100_ir.o
-obj-$(CONFIG_TOSHIBA_FIR)	+= toshoboe.o
+obj-$(CONFIG_TOSHIBA_OLD)	+= toshoboe.o
+obj-$(CONFIG_TOSHIBA_FIR)	+= donauboe.o
 obj-$(CONFIG_SMC_IRCC_FIR)	+= smc-ircc.o	irport.o
 obj-$(CONFIG_ALI_FIR)		+= ali-ircc.o
 obj-$(CONFIG_VLSI_FIR)		+= vlsi_ir.o

drivers/net/mii.c

@@ -243,7 +243,7 @@ unsigned int mii_check_media (struct mii_if_info *mii,
 
 	/* figure out media and duplex from advertise and LPA values */
 	media = mii_nway_result(lpa & advertise);
-	duplex = (media & (ADVERTISE_100FULL | ADVERTISE_10FULL)) ? 1 : 0;
+	duplex = (media & ADVERTISE_FULL) ? 1 : 0;
 
 	if (ok_to_print)
 		printk(KERN_INFO "%s: link up, %sMbps, %s-duplex, lpa 0x%04X\n",

drivers/net/tokenring/tmspci.c

@@ -253,7 +253,7 @@ static int __init tms_pci_init (void)
 	return 0;
 }
 
-static void __devexit tms_pci_rmmod (void)
+static void __exit tms_pci_rmmod (void)
 {
 	pci_unregister_driver (&tms_pci_driver);
 }

drivers/sbus/char/uctrl.c

@@ -107,7 +107,7 @@ struct uctrl_status {
 	u8 speaker_volume; /* 0x23 */
 	u8 control_tft_brightness; /* 0x24 */
 	u8 control_kbd_repeat_delay; /* 0x28 */
-	u8 control_kbd_repeat_rate; /* 0x29 */
+	u8 control_kbd_repeat_period; /* 0x29 */
 	u8 control_screen_contrast; /* 0x2F */
 };
 

drivers/scsi/Config.in

@@ -57,11 +57,6 @@ fi
 source drivers/scsi/aic7xxx/Config.in
 if [ "$CONFIG_SCSI_AIC7XXX" != "y" ]; then
    dep_tristate 'Old Adaptec AIC7xxx support' CONFIG_SCSI_AIC7XXX_OLD $CONFIG_SCSI
-   if [ "$CONFIG_SCSI_AIC7XXX_OLD" != "n" ]; then
-      bool '  Enable Tagged Command Queueing (TCQ) by default' CONFIG_AIC7XXX_OLD_TCQ_ON_BY_DEFAULT
-      int  '  Maximum number of TCQ commands per device' CONFIG_AIC7XXX_OLD_CMDS_PER_DEVICE 8
-      bool '  Collect statistics to report in /proc' CONFIG_AIC7XXX_OLD_PROC_STATS
-   fi
 fi
 # All the I2O code and drivers do not seem to be 64bit safe.
 if [ "$CONFIG_X86_64" != "y" ]; then

drivers/scsi/NCR53C9x.h

@@ -283,6 +283,17 @@ enum esp_rev {
   espunknown = 0x09
 };
 
+/* We allocate one of these for each scsi device and attach it to
+ * SDptr->hostdata for use in the driver
+ */
+struct esp_device {
+  unsigned char sync_min_period;
+  unsigned char sync_max_offset;
+  unsigned sync:1;
+  unsigned wide:1;
+  unsigned disconnect:1;
+};
+
 /* We get one of these for each ESP probed. */
 struct NCR_ESP {
   struct NCR_ESP *next;                   /* Next ESP on probed or NULL */

drivers/scsi/aic7xxx_old/aic7xxx.h

@@ -46,7 +46,6 @@
 	eh_host_reset_handler: NULL,				\
 	abort: aic7xxx_abort,					\
 	reset: aic7xxx_reset,					\
-	select_queue_depths: NULL,				\
 	slave_attach: aic7xxx_slave_attach,			\
 	slave_detach: aic7xxx_slave_detach,			\
 	bios_param: aic7xxx_biosparam,				\

drivers/scsi/aic7xxx_old/aic7xxx_proc.c

@@ -33,7 +33,7 @@
 
 #define	BLS	(&aic7xxx_buffer[size])
 #define HDRB \
-"             < 2K      2K+     4K+     8K+    16K+    32K+    64K+   128K+"
+"             0 - 4K     4 - 16K    16 - 64K   64 - 256K   256K - 1M    1M+"
 
 #ifdef PROC_DEBUG
 extern int vsprintf(char *, const char *, va_list);
@@ -85,10 +85,12 @@ aic7xxx_proc_info ( char *buffer, char **start, off_t offset, int length,
 {
   struct Scsi_Host *HBAptr;
   struct aic7xxx_host *p;
+  struct aic_dev_data *aic_dev;
+  struct scsi_device *sdptr;
   int    size = 0;
   unsigned char i;
-  struct aic7xxx_xferstats *sp;
-  unsigned char target;
+  unsigned char tindex;
+  struct list_head *list_item;
 
   HBAptr = NULL;
 
@@ -130,14 +132,9 @@ aic7xxx_proc_info ( char *buffer, char **start, off_t offset, int length,
    */
 
   size = 4096;
-  for (target = 0; target < MAX_TARGETS; target++)
+  list_for_each(list_item, &p->aic_devs)
   {
-    if (p->dev_flags[target] & DEVICE_PRESENT)
-#ifdef AIC7XXX_PROC_STATS
-      size += 512;
-#else
-      size += 256;
-#endif
+    size += 512;
   }
   if (aic7xxx_buffer_size != size)
   {
@@ -166,11 +163,6 @@ aic7xxx_proc_info ( char *buffer, char **start, off_t offset, int length,
   size += sprintf(BLS, "  TCQ Enabled By Default : Enabled\n");
 #else
   size += sprintf(BLS, "  TCQ Enabled By Default : Disabled\n");
-#endif
-#ifdef AIC7XXX_PROC_STATS
-  size += sprintf(BLS, "  AIC7XXX_PROC_STATS     : Enabled\n");
-#else
-  size += sprintf(BLS, "  AIC7XXX_PROC_STATS     : Disabled\n");
 #endif
   size += sprintf(BLS, "\n");
   size += sprintf(BLS, "Adapter Configuration:\n");
@@ -271,8 +263,6 @@ aic7xxx_proc_info ( char *buffer, char **start, off_t offset, int length,
   {
     size += sprintf(BLS, "     Ultra Enable Flags: 0x%04x\n", p->ultraenb);
   }
-  size += sprintf(BLS, " Tag Queue Enable Flags: 0x%04x\n", p->tagenable);
-  size += sprintf(BLS, "Ordered Queue Tag Flags: 0x%04x\n", p->orderedtag);
   size += sprintf(BLS, "Default Tag Queue Depth: %d\n", AIC7XXX_CMDS_PER_DEVICE);
   size += sprintf(BLS, "    Tagged Queue By Device array for aic7xxx host "
                        "instance %d:\n", p->instance);
@@ -280,43 +270,27 @@ aic7xxx_proc_info ( char *buffer, char **start, off_t offset, int length,
   for(i=0; i < (MAX_TARGETS - 1); i++)
     size += sprintf(BLS, "%d,",aic7xxx_tag_info[p->instance].tag_commands[i]);
   size += sprintf(BLS, "%d}\n",aic7xxx_tag_info[p->instance].tag_commands[i]);
-  size += sprintf(BLS, "    Actual queue depth per device for aic7xxx host "
-                       "instance %d:\n", p->instance);
-  size += sprintf(BLS, "      {");
-  for(i=0; i < (MAX_TARGETS - 1); i++)
-    size += sprintf(BLS, "%d,", p->dev_max_queue_depth[i]);
-  size += sprintf(BLS, "%d}\n", p->dev_max_queue_depth[i]);
 
   size += sprintf(BLS, "\n");
   size += sprintf(BLS, "Statistics:\n\n");
-  for (target = 0; target < MAX_TARGETS; target++)
+  list_for_each(list_item, &p->aic_devs)
   {
-    sp = &p->stats[target];
-    if ((p->dev_flags[target] & DEVICE_PRESENT) == 0)
-    {
-      continue;
-    }
-    if (p->features & AHC_TWIN)
-    {
-      size += sprintf(BLS, "(scsi%d:%d:%d:%d)\n",
-          p->host_no, (target >> 3), (target & 0x7), 0);
-    }
-    else
-    {
-      size += sprintf(BLS, "(scsi%d:%d:%d:%d)\n",
-          p->host_no, 0, target, 0);
-    }
+    aic_dev = list_entry(list_item, struct aic_dev_data, list);
+    sdptr = aic_dev->SDptr;
+    tindex = sdptr->channel << 3 | sdptr->id;
+    size += sprintf(BLS, "(scsi%d:%d:%d:%d)\n",
+        p->host_no, sdptr->channel, sdptr->id, sdptr->lun);
     size += sprintf(BLS, "  Device using %s/%s",
-          (p->transinfo[target].cur_width == MSG_EXT_WDTR_BUS_16_BIT) ?
+          (aic_dev->cur.width == MSG_EXT_WDTR_BUS_16_BIT) ?
           "Wide" : "Narrow",
-          (p->transinfo[target].cur_offset != 0) ?
+          (aic_dev->cur.offset != 0) ?
           "Sync transfers at " : "Async transfers.\n" );
-    if (p->transinfo[target].cur_offset != 0)
+    if (aic_dev->cur.offset != 0)
     {
       struct aic7xxx_syncrate *sync_rate;
-      unsigned char options = p->transinfo[target].cur_options;
-      int period = p->transinfo[target].cur_period;
-      int rate = (p->transinfo[target].cur_width ==
+      unsigned char options = aic_dev->cur.options;
+      int period = aic_dev->cur.period;
+      int rate = (aic_dev->cur.width ==
                   MSG_EXT_WDTR_BUS_16_BIT) ? 1 : 0;
 
       sync_rate = aic7xxx_find_syncrate(p, &period, 0, &options);
@@ -324,50 +298,45 @@ aic7xxx_proc_info ( char *buffer, char **start, off_t offset, int length,
       {
         size += sprintf(BLS, "%s MByte/sec, offset %d\n",
                         sync_rate->rate[rate],
-                        p->transinfo[target].cur_offset );
+                        aic_dev->cur.offset );
       }
       else
       {
         size += sprintf(BLS, "3.3 MByte/sec, offset %d\n",
-                        p->transinfo[target].cur_offset );
+                        aic_dev->cur.offset );
       }
     }
     size += sprintf(BLS, "  Transinfo settings: ");
     size += sprintf(BLS, "current(%d/%d/%d/%d), ",
-                    p->transinfo[target].cur_period,
-                    p->transinfo[target].cur_offset,
-                    p->transinfo[target].cur_width,
-                    p->transinfo[target].cur_options);
+                    aic_dev->cur.period,
+                    aic_dev->cur.offset,
+                    aic_dev->cur.width,
+                    aic_dev->cur.options);
     size += sprintf(BLS, "goal(%d/%d/%d/%d), ",
-                    p->transinfo[target].goal_period,
-                    p->transinfo[target].goal_offset,
-                    p->transinfo[target].goal_width,
-                    p->transinfo[target].goal_options);
+                    aic_dev->goal.period,
+                    aic_dev->goal.offset,
+                    aic_dev->goal.width,
+                    aic_dev->goal.options);
     size += sprintf(BLS, "user(%d/%d/%d/%d)\n",
-                    p->transinfo[target].user_period,
-                    p->transinfo[target].user_offset,
-                    p->transinfo[target].user_width,
-                    p->transinfo[target].user_options);
-#ifdef AIC7XXX_PROC_STATS
+                    p->user[tindex].period,
+                    p->user[tindex].offset,
+                    p->user[tindex].width,
+                    p->user[tindex].options);
     size += sprintf(BLS, "  Total transfers %ld (%ld reads and %ld writes)\n",
-        sp->r_total + sp->w_total, sp->r_total, sp->w_total);
+      aic_dev->r_total + aic_dev->w_total, aic_dev->r_total, aic_dev->w_total);
     size += sprintf(BLS, "%s\n", HDRB);
     size += sprintf(BLS, "   Reads:");
-    for (i = 0; i < NUMBER(sp->r_bins); i++)
+    for (i = 0; i < NUMBER(aic_dev->r_bins); i++)
     {
-      size += sprintf(BLS, " %7ld", sp->r_bins[i]);
+      size += sprintf(BLS, " %7ld", aic_dev->r_bins[i]);
     }
     size += sprintf(BLS, "\n");
     size += sprintf(BLS, "  Writes:");
-    for (i = 0; i < NUMBER(sp->w_bins); i++)
+    for (i = 0; i < NUMBER(aic_dev->w_bins); i++)
     {
-      size += sprintf(BLS, " %7ld", sp->w_bins[i]);
+      size += sprintf(BLS, " %7ld", aic_dev->w_bins[i]);
     }
     size += sprintf(BLS, "\n");
-#else
-    size += sprintf(BLS, "  Total transfers %ld (%ld reads and %ld writes)\n",
-        sp->r_total + sp->w_total, sp->r_total, sp->w_total);
-#endif /* AIC7XXX_PROC_STATS */
     size += sprintf(BLS, "\n\n");
   }
 

drivers/scsi/esp.h

@@ -64,6 +64,17 @@ enum esp_rev {
 	espunknown = 0x07
 };
 
+/* We allocate one of these for each scsi device and attach it to
+ * SDptr->hostdata for use in the driver
+ */
+struct esp_device {
+  unsigned char sync_min_period;
+  unsigned char sync_max_offset;
+  unsigned sync:1;
+  unsigned wide:1;
+  unsigned disconnect:1;
+};
+
 /* We get one of these for each ESP probed. */
 struct esp {
 	unsigned long		eregs;		/* ESP controller registers */
@@ -399,7 +410,7 @@ extern int esp_abort(Scsi_Cmnd *);
 extern int esp_reset(Scsi_Cmnd *, unsigned int);
 extern int esp_proc_info(char *buffer, char **start, off_t offset, int length,
 			 int hostno, int inout);
-extern int esp_revoke(Scsi_Device* SDptr);
+extern void esp_slave_detach(Scsi_Device* SDptr);
 
 #ifdef CONFIG_SPARC64
 #define SCSI_SPARC_ESP {                                        \
@@ -407,7 +418,7 @@ extern int esp_revoke(Scsi_Device* SDptr);
 		proc_info:      &esp_proc_info,			\
 		name:           "Sun ESP 100/100a/200",		\
 		detect:         esp_detect,			\
-		revoke:		esp_revoke,			\
+		slave_detach:	esp_slave_detach,		\
 		info:           esp_info,			\
 		command:        esp_command,			\
 		queuecommand:   esp_queue,			\
@@ -427,7 +438,7 @@ extern int esp_revoke(Scsi_Device* SDptr);
 		proc_info:      &esp_proc_info,			\
 		name:           "Sun ESP 100/100a/200",		\
 		detect:         esp_detect,			\
-		revoke:		esp_revoke,			\
+		slave_detach:	esp_slave_detach,		\
 		info:           esp_info,			\
 		command:        esp_command,			\
 		queuecommand:   esp_queue,			\

drivers/scsi/ips.c

@@ -433,6 +433,7 @@ int ips_eh_abort(Scsi_Cmnd *);
 int ips_eh_reset(Scsi_Cmnd *);
 int ips_queue(Scsi_Cmnd *, void (*) (Scsi_Cmnd *));
 int ips_biosparam(Disk *, struct block_device *, int *);
+int ips_slave_attach(Scsi_Device *);
 const char * ips_info(struct Scsi_Host *);
 void do_ipsintr(int, void *, struct pt_regs *);
 static int ips_hainit(ips_ha_t *);
@@ -481,7 +482,7 @@ static int ips_flash_firmware(ips_ha_t *, ips_passthru_t *, ips_scb_t *);
 static void ips_free_flash_copperhead(ips_ha_t *ha);
 static void ips_get_bios_version(ips_ha_t *, int);
 static void ips_identify_controller(ips_ha_t *);
-static void ips_select_queue_depth(struct Scsi_Host *, Scsi_Device *);
+//static void ips_select_queue_depth(struct Scsi_Host *, Scsi_Device *);
 static void ips_chkstatus(ips_ha_t *, IPS_STATUS *);
 static void ips_enable_int_copperhead(ips_ha_t *);
 static void ips_enable_int_copperhead_memio(ips_ha_t *);
@@ -1087,7 +1088,7 @@ ips_detect(Scsi_Host_Template *SHT) {
          sh->n_io_port = io_addr ? 255 : 0;
          sh->unique_id = (io_addr) ? io_addr : mem_addr;
          sh->irq = irq;
-         sh->select_queue_depths = ips_select_queue_depth;
+         //sh->select_queue_depths = ips_select_queue_depth;
          sh->sg_tablesize = sh->hostt->sg_tablesize;
          sh->can_queue = sh->hostt->can_queue;
          sh->cmd_per_lun = sh->hostt->cmd_per_lun;
@@ -1827,7 +1828,7 @@ ips_biosparam(Disk *disk, struct block_device *dev, int geom[]) {
 /*   Select queue depths for the devices on the contoller                   */
 /*                                                                          */
 /****************************************************************************/
-static void
+/*static void
 ips_select_queue_depth(struct Scsi_Host *host, Scsi_Device *scsi_devs) {
    Scsi_Device *device;
    ips_ha_t    *ha;
@@ -1860,6 +1861,30 @@ ips_select_queue_depth(struct Scsi_Host *host, Scsi_Device *scsi_devs) {
       }
    }
 }
+*/
+
+/****************************************************************************/
+/*                                                                          */
+/* Routine Name: ips_slave_attach                                           */
+/*                                                                          */
+/* Routine Description:                                                     */
+/*                                                                          */
+/*   Set queue depths on devices once scan is complete                      */
+/*                                                                          */
+/****************************************************************************/
+int
+ips_slave_attach(Scsi_Device *SDptr)
+{
+   ips_ha_t    *ha;
+   int          min;
+
+   ha = IPS_HA(SDptr->host);
+   min = ha->max_cmds / 4;
+   if (min < 8)
+      min = ha->max_cmds - 1;
+   scsi_adjust_queue_depth(SDptr, MSG_ORDERED_TAG, min);
+   return 0;
+}
 
 /****************************************************************************/
 /*                                                                          */
@@ -7407,7 +7432,7 @@ static int ips_init_phase1( struct pci_dev *pci_dev, int *indexPtr )
     sh->n_io_port = io_addr ? 255 : 0;
     sh->unique_id = (io_addr) ? io_addr : mem_addr;
     sh->irq = irq;
-    sh->select_queue_depths = ips_select_queue_depth;
+    //sh->select_queue_depths = ips_select_queue_depth;
     sh->sg_tablesize = sh->hostt->sg_tablesize;
     sh->can_queue = sh->hostt->can_queue;
     sh->cmd_per_lun = sh->hostt->cmd_per_lun;

drivers/scsi/ips.h

@@ -60,6 +60,7 @@
    extern int ips_eh_reset(Scsi_Cmnd *);
    extern int ips_queue(Scsi_Cmnd *, void (*) (Scsi_Cmnd *));
    extern int ips_biosparam(Disk *, struct block_device *, int *);
+   extern int ips_slave_attach(Scsi_Device *);
    extern const char * ips_info(struct Scsi_Host *);
    extern void do_ips(int, void *, struct pt_regs *);
 
@@ -481,7 +482,8 @@
     eh_host_reset_handler : ips_eh_reset, \
     abort : NULL,                         \
     reset : NULL,                         \
-    slave_attach : NULL,                  \
+    slave_attach : ips_slave_attach,      \
+    slave_detach : NULL,                  \
     bios_param : ips_biosparam,           \
     can_queue : 0,                        \
     this_id: -1,                          \

drivers/scsi/scsi_ioctl.c

@@ -424,6 +424,14 @@ int scsi_ioctl(Scsi_Device * dev, int cmd, void *arg)
 		return 0;
 	case SCSI_IOCTL_GET_BUS_NUMBER:
 		return put_user(dev->host->host_no, (int *) arg);
+	/*
+	 * The next two ioctls either need to go or need to be changed to
+	 * pass tagged queueing changes through the low level drivers.
+	 * Simply enabling or disabling tagged queueing without the knowledge
+	 * of the low level driver is a *BAD* thing.
+	 *
+	 * Oct. 10, 2002 - Doug Ledford <dledford@redhat.com>
+	 */
 	case SCSI_IOCTL_TAGGED_ENABLE:
 		if (!capable(CAP_SYS_ADMIN))
 			return -EACCES;

drivers/usb/input/hid-input.c

@@ -348,7 +348,7 @@ static void hidinput_configure_usage(struct hid_device *device, struct hid_field
 	set_bit(usage->type, input->evbit);
 
 	while (usage->code <= max && test_and_set_bit(usage->code, bit)) {
-		usage->code = find_next_zero_bit(bit, max + 1, usage->code);
+		usage->code = find_next_zero_bit(bit, usage->code, max + 1);
 	}
 
 	if (usage->code > max) return;