Commit 089651ef authored by Uwe Kleine-König's avatar Uwe Kleine-König Committed by Greg Kroah-Hartman

spi: imx: mx51-ecspi: Move some initialisation to prepare_message hook.

The relevant difference between prepare_message and config is that the
former is run before the CS signal is asserted. So the polarity of the
CLK line must be configured in prepare_message as an edge generated by
config might already result in a latch of the MOSI line.
Signed-off-by: default avatarUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: default avatarMark Brown <broonie@kernel.org>
[ukleinek: backport to v4.14.x]
Signed-off-by: default avatarUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: default avatarSasha Levin <sashal@kernel.org>
parent 0cc6feb5
......@@ -443,14 +443,9 @@ static void mx51_ecspi_trigger(struct spi_imx_data *spi_imx)
static int mx51_ecspi_prepare_message(struct spi_imx_data *spi_imx,
struct spi_message *msg)
{
return 0;
}
static int mx51_ecspi_config(struct spi_device *spi)
{
struct spi_imx_data *spi_imx = spi_master_get_devdata(spi->master);
struct spi_device *spi = msg->spi;
u32 ctrl = MX51_ECSPI_CTRL_ENABLE;
u32 clk = spi_imx->speed_hz, delay, reg;
u32 testreg;
u32 cfg = readl(spi_imx->base + MX51_ECSPI_CONFIG);
/*
......@@ -468,14 +463,21 @@ static int mx51_ecspi_config(struct spi_device *spi)
if (spi->mode & SPI_READY)
ctrl |= MX51_ECSPI_CTRL_DRCTL(spi_imx->spi_drctl);
/* set clock speed */
ctrl |= mx51_ecspi_clkdiv(spi_imx, spi_imx->speed_hz, &clk);
spi_imx->spi_bus_clk = clk;
/* set chip select to use */
ctrl |= MX51_ECSPI_CTRL_CS(spi->chip_select);
ctrl |= (spi_imx->bits_per_word - 1) << MX51_ECSPI_CTRL_BL_OFFSET;
/*
* The ctrl register must be written first, with the EN bit set other
* registers must not be written to.
*/
writel(ctrl, spi_imx->base + MX51_ECSPI_CTRL);
testreg = readl(spi_imx->base + MX51_ECSPI_TESTREG);
if (spi->mode & SPI_LOOP)
testreg |= MX51_ECSPI_TESTREG_LBC;
else
testreg &= ~MX51_ECSPI_TESTREG_LBC;
writel(testreg, spi_imx->base + MX51_ECSPI_TESTREG);
cfg |= MX51_ECSPI_CONFIG_SBBCTRL(spi->chip_select);
......@@ -491,26 +493,38 @@ static int mx51_ecspi_config(struct spi_device *spi)
cfg &= ~MX51_ECSPI_CONFIG_SCLKPOL(spi->chip_select);
cfg &= ~MX51_ECSPI_CONFIG_SCLKCTL(spi->chip_select);
}
if (spi->mode & SPI_CS_HIGH)
cfg |= MX51_ECSPI_CONFIG_SSBPOL(spi->chip_select);
else
cfg &= ~MX51_ECSPI_CONFIG_SSBPOL(spi->chip_select);
writel(cfg, spi_imx->base + MX51_ECSPI_CONFIG);
return 0;
}
static int mx51_ecspi_config(struct spi_device *spi)
{
struct spi_imx_data *spi_imx = spi_master_get_devdata(spi->master);
u32 ctrl = readl(spi_imx->base + MX51_ECSPI_CTRL);
u32 clk = spi_imx->speed_hz, delay;
/* Clear BL field and set the right value */
ctrl &= ~MX51_ECSPI_CTRL_BL_MASK;
ctrl |= (spi_imx->bits_per_word - 1) << MX51_ECSPI_CTRL_BL_OFFSET;
/* set clock speed */
ctrl &= ~(0xf << MX51_ECSPI_CTRL_POSTDIV_OFFSET |
0xf << MX51_ECSPI_CTRL_PREDIV_OFFSET);
ctrl |= mx51_ecspi_clkdiv(spi_imx, spi_imx->speed_hz, &clk);
spi_imx->spi_bus_clk = clk;
if (spi_imx->usedma)
ctrl |= MX51_ECSPI_CTRL_SMC;
/* CTRL register always go first to bring out controller from reset */
writel(ctrl, spi_imx->base + MX51_ECSPI_CTRL);
reg = readl(spi_imx->base + MX51_ECSPI_TESTREG);
if (spi->mode & SPI_LOOP)
reg |= MX51_ECSPI_TESTREG_LBC;
else
reg &= ~MX51_ECSPI_TESTREG_LBC;
writel(reg, spi_imx->base + MX51_ECSPI_TESTREG);
writel(cfg, spi_imx->base + MX51_ECSPI_CONFIG);
/*
* Wait until the changes in the configuration register CONFIGREG
* propagate into the hardware. It takes exactly one tick of the
......@@ -532,7 +546,6 @@ static int mx51_ecspi_config(struct spi_device *spi)
* Configure the DMA register: setup the watermark
* and enable DMA request.
*/
writel(MX51_ECSPI_DMA_RX_WML(spi_imx->wml) |
MX51_ECSPI_DMA_TX_WML(spi_imx->wml) |
MX51_ECSPI_DMA_RXT_WML(spi_imx->wml) |
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment