Skip to content

L
linux
Commit 09c0998e authored by Mark Brown's avatar Mark Brown
Browse files
Options

Merge tag 'spi-v3.15' into spi-linus 

spi: Updates for v3.15

A busy release for both cleanups and new drivers this time along with
further factoring out of replicated code into the core:

 - Provide support in the core for DMA mapping transfers - essentially
   all drivers weren't implementing this properly, now there's no
   excuse.
 - Dual and quad mode support for spidev.
 - Fix handling of cs_change in the generic implementation.
 - Remove the S3C_DMA code from the s3c64xx driver now that all the
   platforms using it have been converted to dmaengine.
 - Lots of improvements to the Renesas SPI controllers.
 - Drivers for Allwinner A10 and A31, Qualcomm QUP and Xylinx xtfpga.
 - Removal of the bitrotted ti-ssp driver.

# gpg: Signature made Mon 31 Mar 2014 12:03:09 BST using RSA key ID 7EA229BD
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg:                 aka "Mark Brown <broonie@debian.org>"
# gpg:                 aka "Mark Brown <broonie@kernel.org>"
# gpg:                 aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg:                 aka "Mark Brown <broonie@linaro.org>"
# gpg:                 aka "Mark Brown <Mark.Brown@linaro.org>"
parents 455c6fdb 45b15d98
Expand all Hide whitespace changes
Inline Side-by-side
Showing with 4129 additions and 2298 deletions
Documentation/devicetree/bindings/spi/efm32-spi.txt
View file @ 09c0998e
......@@ -3,24 +3,24 @@
Required properties:
- #address-cells: see spi-bus.txt
- #size-cells: see spi-bus.txt
- compatible: should be "efm32,spi"
- compatible: should be "energymicro,efm32-spi"
- reg: Offset and length of the register set for the controller
- interrupts: pair specifying rx and tx irq
- clocks: phandle to the spi clock
- cs-gpios: see spi-bus.txt
- location: Value to write to the ROUTE register's LOCATION bitfield to configure the pinmux for the device, see datasheet for values.
- efm32,location: Value to write to the ROUTE register's LOCATION bitfield to configure the pinmux for the device, see datasheet for values.
Example:
spi1: spi@0x4000c400 { /* USART1 */
#address-cells = <1>;
#size-cells = <0>;
compatible = "efm32,spi";
compatible = "energymicro,efm32-spi";
reg = <0x4000c400 0x400>;
interrupts = <15 16>;
clocks = <&cmu 20>;
cs-gpios = <&gpio 51 1>; // D3
location = <1>;
efm32,location = <1>;
status = "ok";
ks8851@0 {
......
Documentation/devicetree/bindings/spi/qcom,spi-qup.txt 0 → 100644
View file @ 09c0998e
Qualcomm Universal Peripheral (QUP) Serial Peripheral Interface (SPI)
The QUP core is an AHB slave that provides a common data path (an output FIFO
and an input FIFO) for serial peripheral interface (SPI) mini-core.
SPI in master mode supports up to 50MHz, up to four chip selects, programmable
data path from 4 bits to 32 bits and numerous protocol variants.
Required properties:
- compatible: Should contain "qcom,spi-qup-v2.1.1" or "qcom,spi-qup-v2.2.1"
- reg: Should contain base register location and length
- interrupts: Interrupt number used by this controller
- clocks: Should contain the core clock and the AHB clock.
- clock-names: Should be "core" for the core clock and "iface" for the
AHB clock.
- #address-cells: Number of cells required to define a chip select
address on the SPI bus. Should be set to 1.
- #size-cells: Should be zero.
Optional properties:
- spi-max-frequency: Specifies maximum SPI clock frequency,
Units - Hz. Definition as per
Documentation/devicetree/bindings/spi/spi-bus.txt
SPI slave nodes must be children of the SPI master node and can contain
properties described in Documentation/devicetree/bindings/spi/spi-bus.txt
Example:
spi_8: spi@f9964000 { /* BLSP2 QUP2 */
compatible = "qcom,spi-qup-v2";
#address-cells = <1>;
#size-cells = <0>;
reg = <0xf9964000 0x1000>;
interrupts = <0 102 0>;
spi-max-frequency = <19200000>;
clocks = <&gcc GCC_BLSP2_QUP2_SPI_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
clock-names = "core", "iface";
pinctrl-names = "default";
pinctrl-0 = <&spi8_default>;
device@0 {
compatible = "arm,pl022-dummy";
#address-cells = <1>;
#size-cells = <1>;
reg = <0>; /* Chip select 0 */
spi-max-frequency = <19200000>;
spi-cpol;
};
device@1 {
compatible = "arm,pl022-dummy";
#address-cells = <1>;
#size-cells = <1>;
reg = <1>; /* Chip select 1 */
spi-max-frequency = <9600000>;
spi-cpha;
};
device@2 {
compatible = "arm,pl022-dummy";
#address-cells = <1>;
#size-cells = <1>;
reg = <2>; /* Chip select 2 */
spi-max-frequency = <19200000>;
spi-cpol;
spi-cpha;
};
device@3 {
compatible = "arm,pl022-dummy";
#address-cells = <1>;
#size-cells = <1>;
reg = <3>; /* Chip select 3 */
spi-max-frequency = <19200000>;
spi-cpol;
spi-cpha;
spi-cs-high;
};
};
Documentation/devicetree/bindings/spi/sh-hspi.txt
View file @ 09c0998e
Renesas HSPI.
Required properties:
- compatible : "renesas,hspi"
- reg : Offset and length of the register set for the device
- interrupts : interrupt line used by HSPI
- compatible : "renesas,hspi-<soctype>", "renesas,hspi" as fallback.
Examples with soctypes are:
- "renesas,hspi-r8a7778" (R-Car M1)
- "renesas,hspi-r8a7779" (R-Car H1)
- reg : Offset and length of the register set for the device
- interrupt-parent : The phandle for the interrupt controller that
services interrupts for this device
- interrupts : Interrupt specifier
- #address-cells : Must be <1>
- #size-cells : Must be <0>
Pinctrl properties might be needed, too. See
Documentation/devicetree/bindings/pinctrl/renesas,*.
Example:
hspi0: spi@fffc7000 {
compatible = "renesas,hspi-r8a7778", "renesas,hspi";
reg = <0xfffc7000 0x18>;
interrupt-parent = <&gic>;
interrupts = <0 63 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
Documentation/devicetree/bindings/spi/sh-msiof.txt
View file @ 09c0998e
Renesas MSIOF spi controller
Required properties:
- compatible : "renesas,sh-msiof" for SuperH or
"renesas,sh-mobile-msiof" for SH Mobile series
- reg : Offset and length of the register set for the device
- interrupts : interrupt line used by MSIOF
- compatible : "renesas,msiof-<soctype>" for SoCs,
"renesas,sh-msiof" for SuperH, or
"renesas,sh-mobile-msiof" for SH Mobile series.
Examples with soctypes are:
"renesas,msiof-r8a7790" (R-Car H2)
"renesas,msiof-r8a7791" (R-Car M2)
- reg : Offset and length of the register set for the device
- interrupt-parent : The phandle for the interrupt controller that
services interrupts for this device
- interrupts : Interrupt specifier
- #address-cells : Must be <1>
- #size-cells : Must be <0>
Optional properties:
- num-cs : total number of chip-selects
- renesas,tx-fifo-size : Overrides the default tx fifo size given in words
- renesas,rx-fifo-size : Overrides the default rx fifo size given in words
- clocks : Must contain a reference to the functional clock.
- num-cs : Total number of chip-selects (default is 1)
Optional properties, deprecated for soctype-specific bindings:
- renesas,tx-fifo-size : Overrides the default tx fifo size given in words
(default is 64)
- renesas,rx-fifo-size : Overrides the default rx fifo size given in words
(default is 64, or 256 on R-Car H2 and M2)
Pinctrl properties might be needed, too. See
Documentation/devicetree/bindings/pinctrl/renesas,*.
Example:
msiof0: spi@e6e20000 {
compatible = "renesas,msiof-r8a7791";
reg = <0 0xe6e20000 0 0x0064>;
interrupts = <0 156 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp0_clks R8A7791_CLK_MSIOF0>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt
View file @ 09c0998e
......@@ -10,6 +10,7 @@ Required properties:
- pinctrl-names: must contain a "default" entry.
- spi-num-chipselects : the number of the chipselect signals.
- bus-num : the slave chip chipselect signal number.
- big-endian : if DSPI modudle is big endian, the bool will be set in node.
Example:
dspi0@4002c000 {
......@@ -24,6 +25,7 @@ dspi0@4002c000 {
bus-num = <0>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_dspi0_1>;
big-endian;
status = "okay";
sflash: at26df081a@0 {
......
Documentation/devicetree/bindings/spi/spi-rspi.txt 0 → 100644
View file @ 09c0998e
Device tree configuration for Renesas RSPI/QSPI driver
Required properties:
- compatible : For Renesas Serial Peripheral Interface on legacy SH:
"renesas,rspi-<soctype>", "renesas,rspi" as fallback.
For Renesas Serial Peripheral Interface on RZ/A1H:
"renesas,rspi-<soctype>", "renesas,rspi-rz" as fallback.
For Quad Serial Peripheral Interface on R-Car Gen2:
"renesas,qspi-<soctype>", "renesas,qspi" as fallback.
Examples with soctypes are:
- "renesas,rspi-sh7757" (SH)
- "renesas,rspi-r7s72100" (RZ/A1H)
- "renesas,qspi-r8a7790" (R-Car H2)
- "renesas,qspi-r8a7791" (R-Car M2)
- reg : Address start and address range size of the device
- interrupts : A list of interrupt-specifiers, one for each entry in
interrupt-names.
If interrupt-names is not present, an interrupt specifier
for a single muxed interrupt.
- interrupt-names : A list of interrupt names. Should contain (if present):
- "error" for SPEI,
- "rx" for SPRI,
- "tx" to SPTI,
- "mux" for a single muxed interrupt.
- interrupt-parent : The phandle for the interrupt controller that
services interrupts for this device.
- num-cs : Number of chip selects. Some RSPI cores have more than 1.
- #address-cells : Must be <1>
- #size-cells : Must be <0>
Optional properties:
- clocks : Must contain a reference to the functional clock.
Pinctrl properties might be needed, too. See
Documentation/devicetree/bindings/pinctrl/renesas,*.
Examples:
spi0: spi@e800c800 {
compatible = "renesas,rspi-r7s72100", "renesas,rspi-rz";
reg = <0xe800c800 0x24>;
interrupts = <0 238 IRQ_TYPE_LEVEL_HIGH>,
<0 239 IRQ_TYPE_LEVEL_HIGH>,
<0 240 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "error", "rx", "tx";
interrupt-parent = <&gic>;
num-cs = <1>;
#address-cells = <1>;
#size-cells = <0>;
};
spi: spi@e6b10000 {
compatible = "renesas,qspi-r8a7791", "renesas,qspi";
reg = <0 0xe6b10000 0 0x2c>;
interrupt-parent = <&gic>;
interrupts = <0 184 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7791_CLK_QSPI_MOD>;
num-cs = <1>;
#address-cells = <1>;
#size-cells = <0>;
};
Documentation/devicetree/bindings/spi/spi-sun4i.txt 0 → 100644
View file @ 09c0998e
Allwinner A10 SPI controller
Required properties:
- compatible: Should be "allwinner,sun4-a10-spi".
- reg: Should contain register location and length.
- interrupts: Should contain interrupt.
- clocks: phandle to the clocks feeding the SPI controller. Two are
needed:
- "ahb": the gated AHB parent clock
- "mod": the parent module clock
- clock-names: Must contain the clock names described just above
Example:
spi1: spi@01c06000 {
compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c06000 0x1000>;
interrupts = <11>;
clocks = <&ahb_gates 21>, <&spi1_clk>;
clock-names = "ahb", "mod";
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
Documentation/devicetree/bindings/spi/spi-sun6i.txt 0 → 100644
View file @ 09c0998e
Allwinner A31 SPI controller
Required properties:
- compatible: Should be "allwinner,sun6i-a31-spi".
- reg: Should contain register location and length.
- interrupts: Should contain interrupt.
- clocks: phandle to the clocks feeding the SPI controller. Two are
needed:
- "ahb": the gated AHB parent clock
- "mod": the parent module clock
- clock-names: Must contain the clock names described just above
- resets: phandle to the reset controller asserting this device in
reset
Example:
spi1: spi@01c69000 {
compatible = "allwinner,sun6i-a31-spi";
reg = <0x01c69000 0x1000>;
interrupts = <0 66 4>;
clocks = <&ahb1_gates 21>, <&spi1_clk>;
clock-names = "ahb", "mod";
resets = <&ahb1_rst 21>;
};
Documentation/devicetree/bindings/spi/spi-xtensa-xtfpga.txt 0 → 100644
View file @ 09c0998e
Cadence Xtensa XTFPGA platform SPI controller.
This simple SPI master controller is built into xtfpga bitstreams and is used
to control daughterboard audio codec.
Required properties:
- compatible: should be "cdns,xtfpga-spi".
- reg: physical base address of the controller and length of memory mapped
region.
Documentation/spi/spidev
View file @ 09c0998e
......@@ -85,6 +85,12 @@ settings for data transfer parameters:
SPI_MODE_0..SPI_MODE_3; or if you prefer you can combine SPI_CPOL
(clock polarity, idle high iff this is set) or SPI_CPHA (clock phase,
sample on trailing edge iff this is set) flags.
Note that this request is limited to SPI mode flags that fit in a
single byte.
SPI_IOC_RD_MODE32, SPI_IOC_WR_MODE32 ... pass a pointer to a uin32_t
which will return (RD) or assign (WR) the full SPI transfer mode,
not limited to the bits that fit in one byte.
SPI_IOC_RD_LSB_FIRST, SPI_IOC_WR_LSB_FIRST ... pass a pointer to a byte
which will return (RD) or assign (WR) the bit justification used to
......
Documentation/spi/spidev_fdx.c
View file @ 09c0998e
......@@ -78,10 +78,10 @@ static void do_msg(int fd, int len)
static void dumpstat(const char *name, int fd)
{
__u8 mode, lsb, bits;
__u32 speed;
__u8 lsb, bits;
__u32 mode, speed;
if (ioctl(fd, SPI_IOC_RD_MODE, &mode) < 0) {
if (ioctl(fd, SPI_IOC_RD_MODE32, &mode) < 0) {
perror("SPI rd_mode");
return;
}
......@@ -98,7 +98,7 @@ static void dumpstat(const char *name, int fd)
return;
}
printf("%s: spi mode %d, %d bits %sper word, %d Hz max\n",
printf("%s: spi mode 0x%x, %d bits %sper word, %d Hz max\n",
name, mode, bits, lsb ? "(lsb first) " : "", speed);
}
......
Documentation/spi/spidev_test.c
View file @ 09c0998e
......@@ -30,7 +30,7 @@ static void pabort(const char *s)
}
static const char *device = "/dev/spidev1.1";
static uint8_t mode;
static uint32_t mode;
static uint8_t bits = 8;
static uint32_t speed = 500000;
static uint16_t delay;
......@@ -57,6 +57,21 @@ static void transfer(int fd)
.bits_per_word = bits,
};
if (mode & SPI_TX_QUAD)
tr.tx_nbits = 4;
else if (mode & SPI_TX_DUAL)
tr.tx_nbits = 2;
if (mode & SPI_RX_QUAD)
tr.rx_nbits = 4;
else if (mode & SPI_RX_DUAL)
tr.rx_nbits = 2;
if (!(mode & SPI_LOOP)) {
if (mode & (SPI_TX_QUAD | SPI_TX_DUAL))
tr.rx_buf = 0;
else if (mode & (SPI_RX_QUAD | SPI_RX_DUAL))
tr.tx_buf = 0;
}
ret = ioctl(fd, SPI_IOC_MESSAGE(1), &tr);
if (ret < 1)
pabort("can't send spi message");
......@@ -81,7 +96,11 @@ static void print_usage(const char *prog)
" -O --cpol clock polarity\n"
" -L --lsb least significant bit first\n"
" -C --cs-high chip select active high\n"
" -3 --3wire SI/SO signals shared\n");
" -3 --3wire SI/SO signals shared\n"
" -N --no-cs no chip select\n"
" -R --ready slave pulls low to pause\n"
" -2 --dual dual transfer\n"
" -4 --quad quad transfer\n");
exit(1);
}
......@@ -101,11 +120,13 @@ static void parse_opts(int argc, char *argv[])
{ "3wire", 0, 0, '3' },
{ "no-cs", 0, 0, 'N' },
{ "ready", 0, 0, 'R' },
{ "dual", 0, 0, '2' },
{ "quad", 0, 0, '4' },
{ NULL, 0, 0, 0 },
};
int c;
c = getopt_long(argc, argv, "D:s:d:b:lHOLC3NR", lopts, NULL);
c = getopt_long(argc, argv, "D:s:d:b:lHOLC3NR24", lopts, NULL);
if (c == -1)
break;
......@@ -147,11 +168,23 @@ static void parse_opts(int argc, char *argv[])
case 'R':
mode |= SPI_READY;
break;
case '2':
mode |= SPI_TX_DUAL;
break;
case '4':
mode |= SPI_TX_QUAD;
break;
default:
print_usage(argv[0]);
break;
}
}
if (mode & SPI_LOOP) {
if (mode & SPI_TX_DUAL)
mode |= SPI_RX_DUAL;
if (mode & SPI_TX_QUAD)
mode |= SPI_RX_QUAD;
}
}
int main(int argc, char *argv[])
......@@ -168,11 +201,11 @@ int main(int argc, char *argv[])
/*
* spi mode
*/
ret = ioctl(fd, SPI_IOC_WR_MODE, &mode);
ret = ioctl(fd, SPI_IOC_WR_MODE32, &mode);
if (ret == -1)
pabort("can't set spi mode");
ret = ioctl(fd, SPI_IOC_RD_MODE, &mode);
ret = ioctl(fd, SPI_IOC_RD_MODE32, &mode);
if (ret == -1)
pabort("can't get spi mode");
......@@ -198,7 +231,7 @@ int main(int argc, char *argv[])
if (ret == -1)
pabort("can't get max speed hz");
printf("spi mode: %d\n", mode);
printf("spi mode: 0x%x\n", mode);
printf("bits per word: %d\n", bits);
printf("max speed: %d Hz (%d KHz)\n", speed, speed/1000);
......
MAINTAINERS
View file @ 09c0998e
......@@ -9783,6 +9783,12 @@ L: linux-serial@vger.kernel.org
S: Maintained
F: drivers/tty/serial/uartlite.c
XTENSA XTFPGA PLATFORM SUPPORT
M: Max Filippov <jcmvbkbc@gmail.com>
L: linux-xtensa@linux-xtensa.org
S: Maintained
F: drivers/spi/spi-xtensa-xtfpga.c
YAM DRIVER FOR AX.25
M: Jean-Paul Roubelat <jpr@f6fbb.org>
L: linux-hams@vger.kernel.org
......
drivers/base/power/Makefile
View file @ 09c0998e
obj-$(CONFIG_PM) += sysfs.o generic_ops.o common.o qos.o
obj-$(CONFIG_PM) += sysfs.o generic_ops.o common.o qos.o runtime.o
obj-$(CONFIG_PM_SLEEP) += main.o wakeup.o
obj-$(CONFIG_PM_RUNTIME) += runtime.o
obj-$(CONFIG_PM_TRACE_RTC) += trace.o
obj-$(CONFIG_PM_OPP) += opp.o
obj-$(CONFIG_PM_GENERIC_DOMAINS) += domain.o domain_governor.o
......
drivers/base/power/runtime.c
View file @ 09c0998e
......@@ -13,6 +13,43 @@
#include <trace/events/rpm.h>
#include "power.h"
#define RPM_GET_CALLBACK(dev, cb) \
({ \
int (*__rpm_cb)(struct device *__d); \
\
if (dev->pm_domain) \
__rpm_cb = dev->pm_domain->ops.cb; \
else if (dev->type && dev->type->pm) \
__rpm_cb = dev->type->pm->cb; \
else if (dev->class && dev->class->pm) \
__rpm_cb = dev->class->pm->cb; \
else if (dev->bus && dev->bus->pm) \
__rpm_cb = dev->bus->pm->cb; \
else \
__rpm_cb = NULL; \
\
if (!__rpm_cb && dev->driver && dev->driver->pm) \
__rpm_cb = dev->driver->pm->cb; \
\
__rpm_cb; \
})
static int (*rpm_get_suspend_cb(struct device *dev))(struct device *)
{
return RPM_GET_CALLBACK(dev, runtime_suspend);
}
static int (*rpm_get_resume_cb(struct device *dev))(struct device *)
{
return RPM_GET_CALLBACK(dev, runtime_resume);
}
#ifdef CONFIG_PM_RUNTIME
static int (*rpm_get_idle_cb(struct device *dev))(struct device *)
{
return RPM_GET_CALLBACK(dev, runtime_idle);
}
static int rpm_resume(struct device *dev, int rpmflags);
static int rpm_suspend(struct device *dev, int rpmflags);
......@@ -310,19 +347,7 @@ static int rpm_idle(struct device *dev, int rpmflags)
dev->power.idle_notification = true;
if (dev->pm_domain)
callback = dev->pm_domain->ops.runtime_idle;
else if (dev->type && dev->type->pm)
callback = dev->type->pm->runtime_idle;
else if (dev->class && dev->class->pm)
callback = dev->class->pm->runtime_idle;
else if (dev->bus && dev->bus->pm)
callback = dev->bus->pm->runtime_idle;
else
callback = NULL;
if (!callback && dev->driver && dev->driver->pm)
callback = dev->driver->pm->runtime_idle;
callback = rpm_get_idle_cb(dev);
if (callback)
retval = __rpm_callback(callback, dev);
......@@ -492,19 +517,7 @@ static int rpm_suspend(struct device *dev, int rpmflags)
__update_runtime_status(dev, RPM_SUSPENDING);
if (dev->pm_domain)
callback = dev->pm_domain->ops.runtime_suspend;
else if (dev->type && dev->type->pm)
callback = dev->type->pm->runtime_suspend;
else if (dev->class && dev->class->pm)
callback = dev->class->pm->runtime_suspend;
else if (dev->bus && dev->bus->pm)
callback = dev->bus->pm->runtime_suspend;
else
callback = NULL;
if (!callback && dev->driver && dev->driver->pm)
callback = dev->driver->pm->runtime_suspend;
callback = rpm_get_suspend_cb(dev);
retval = rpm_callback(callback, dev);
if (retval)
......@@ -724,19 +737,7 @@ static int rpm_resume(struct device *dev, int rpmflags)
__update_runtime_status(dev, RPM_RESUMING);
if (dev->pm_domain)
callback = dev->pm_domain->ops.runtime_resume;
else if (dev->type && dev->type->pm)
callback = dev->type->pm->runtime_resume;
else if (dev->class && dev->class->pm)
callback = dev->class->pm->runtime_resume;
else if (dev->bus && dev->bus->pm)
callback = dev->bus->pm->runtime_resume;
else
callback = NULL;
if (!callback && dev->driver && dev->driver->pm)
callback = dev->driver->pm->runtime_resume;
callback = rpm_get_resume_cb(dev);
retval = rpm_callback(callback, dev);
if (retval) {
......@@ -1401,3 +1402,86 @@ void pm_runtime_remove(struct device *dev)
if (dev->power.irq_safe && dev->parent)
pm_runtime_put(dev->parent);
}
#endif
/**
* pm_runtime_force_suspend - Force a device into suspend state if needed.
* @dev: Device to suspend.
*
* Disable runtime PM so we safely can check the device's runtime PM status and
* if it is active, invoke it's .runtime_suspend callback to bring it into
* suspend state. Keep runtime PM disabled to preserve the state unless we
* encounter errors.
*
* Typically this function may be invoked from a system suspend callback to make
* sure the device is put into low power state.
*/
int pm_runtime_force_suspend(struct device *dev)
{
int (*callback)(struct device *);
int ret = 0;
pm_runtime_disable(dev);
/*
* Note that pm_runtime_status_suspended() returns false while
* !CONFIG_PM_RUNTIME, which means the device will be put into low
* power state.
*/
if (pm_runtime_status_suspended(dev))
return 0;
callback = rpm_get_suspend_cb(dev);
if (!callback) {
ret = -ENOSYS;
goto err;
}
ret = callback(dev);
if (ret)
goto err;
pm_runtime_set_suspended(dev);
return 0;
err:
pm_runtime_enable(dev);
return ret;
}
EXPORT_SYMBOL_GPL(pm_runtime_force_suspend);
/**
* pm_runtime_force_resume - Force a device into resume state.
* @dev: Device to resume.
*
* Prior invoking this function we expect the user to have brought the device
* into low power state by a call to pm_runtime_force_suspend(). Here we reverse
* those actions and brings the device into full power. We update the runtime PM
* status and re-enables runtime PM.
*
* Typically this function may be invoked from a system resume callback to make
* sure the device is put into full power state.
*/
int pm_runtime_force_resume(struct device *dev)
{
int (*callback)(struct device *);
int ret = 0;
callback = rpm_get_resume_cb(dev);
if (!callback) {
ret = -ENOSYS;
goto out;
}
ret = callback(dev);
if (ret)
goto out;
pm_runtime_set_active(dev);
pm_runtime_mark_last_busy(dev);
out:
pm_runtime_enable(dev);
return ret;
}
EXPORT_SYMBOL_GPL(pm_runtime_force_resume);
drivers/spi/Kconfig
View file @ 09c0998e
......@@ -150,7 +150,7 @@ config SPI_BUTTERFLY
config SPI_CLPS711X
tristate "CLPS711X host SPI controller"
depends on ARCH_CLPS711X
depends on ARCH_CLPS711X || COMPILE_TEST
help
This enables dedicated general purpose SPI/Microwire1-compatible
master mode interface (SSI1) for CLPS711X-based CPUs.
......@@ -212,7 +212,6 @@ config SPI_IMX
tristate "Freescale i.MX SPI controllers"
depends on ARCH_MXC || COMPILE_TEST
select SPI_BITBANG
default m if IMX_HAVE_PLATFORM_SPI_IMX
help
This enables using the Freescale i.MX SPI controllers in master
mode.
......@@ -270,6 +269,7 @@ config SPI_FSL_SPI
config SPI_FSL_DSPI
tristate "Freescale DSPI controller"
select SPI_BITBANG
select REGMAP_MMIO
depends on SOC_VF610 || COMPILE_TEST
help
This enables support for the Freescale DSPI controller in master
......@@ -307,7 +307,7 @@ config SPI_OMAP_UWIRE
config SPI_OMAP24XX
tristate "McSPI driver for OMAP"
depends on ARM || ARM64 || AVR32 || HEXAGON || MIPS || SH
depends on ARM || ARM64 || AVR32 || HEXAGON || MIPS || SUPERH
depends on ARCH_OMAP2PLUS || COMPILE_TEST
help
SPI master controller for OMAP24XX and later Multichannel SPI
......@@ -381,6 +381,19 @@ config SPI_RSPI
help
SPI driver for Renesas RSPI and QSPI blocks.
config SPI_QUP
tristate "Qualcomm SPI controller with QUP interface"
depends on ARCH_MSM_DT || (ARM && COMPILE_TEST)
help
Qualcomm Universal Peripheral (QUP) core is an AHB slave that
provides a common data path (an output FIFO and an input FIFO)
for serial peripheral interface (SPI) mini-core. SPI in master
mode supports up to 50MHz, up to four chip selects, programmable
data path from 4 bits to 32 bits and numerous protocol variants.
This driver can also be built as a module. If so, the module
will be called spi_qup.
config SPI_S3C24XX
tristate "Samsung S3C24XX series SPI"
depends on ARCH_S3C24XX
......@@ -416,7 +429,6 @@ config SPI_SH_MSIOF
tristate "SuperH MSIOF SPI controller"
depends on HAVE_CLK
depends on SUPERH || ARCH_SHMOBILE || COMPILE_TEST
select SPI_BITBANG
help
SPI driver for SuperH and SH Mobile MSIOF blocks.
......@@ -446,6 +458,19 @@ config SPI_SIRF
help
SPI driver for CSR SiRFprimaII SoCs
config SPI_SUN4I
tristate "Allwinner A10 SoCs SPI controller"
depends on ARCH_SUNXI || COMPILE_TEST
help
SPI driver for Allwinner sun4i, sun5i and sun7i SoCs
config SPI_SUN6I
tristate "Allwinner A31 SPI controller"
depends on ARCH_SUNXI || COMPILE_TEST
depends on RESET_CONTROLLER
help
This enables using the SPI controller on the Allwinner A31 SoCs.
config SPI_MXS
tristate "Freescale MXS SPI controller"
depends on ARCH_MXS
......@@ -478,13 +503,6 @@ config SPI_TEGRA20_SLINK
help
SPI driver for Nvidia Tegra20/Tegra30 SLINK Controller interface.
config SPI_TI_SSP
tristate "TI Sequencer Serial Port - SPI Support"
depends on MFD_TI_SSP
help
This selects an SPI master implementation using a TI sequencer
serial port.
config SPI_TOPCLIFF_PCH
tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) SPI"
depends on PCI
......@@ -520,6 +538,19 @@ config SPI_XILINX
Or for the DS570, see "XPS Serial Peripheral Interface (SPI) (v2.00b)"
config SPI_XTENSA_XTFPGA
tristate "Xtensa SPI controller for xtfpga"
depends on (XTENSA && XTENSA_PLATFORM_XTFPGA) || COMPILE_TEST
select SPI_BITBANG
help
SPI driver for xtfpga SPI master controller.
This simple SPI master controller is built into xtfpga bitstreams
and is used to control daughterboard audio codec. It always transfers
16 bit words in SPI mode 0, automatically asserting CS on transfer
start and deasserting on end.
config SPI_NUC900
tristate "Nuvoton NUC900 series SPI"
depends on ARCH_W90X900
......@@ -546,7 +577,7 @@ config SPI_DW_MID_DMA
config SPI_DW_MMIO
tristate "Memory-mapped io interface driver for DW SPI core"
depends on SPI_DESIGNWARE && HAVE_CLK
depends on SPI_DESIGNWARE
#
# There are lots of SPI device types, with sensors and memory
......
drivers/spi/Makefile
View file @ 09c0998e
......@@ -59,6 +59,7 @@ spi-pxa2xx-platform-$(CONFIG_SPI_PXA2XX_PXADMA) += spi-pxa2xx-pxadma.o
spi-pxa2xx-platform-$(CONFIG_SPI_PXA2XX_DMA) += spi-pxa2xx-dma.o
obj-$(CONFIG_SPI_PXA2XX) += spi-pxa2xx-platform.o
obj-$(CONFIG_SPI_PXA2XX_PCI) += spi-pxa2xx-pci.o
obj-$(CONFIG_SPI_QUP) += spi-qup.o
obj-$(CONFIG_SPI_RSPI) += spi-rspi.o
obj-$(CONFIG_SPI_S3C24XX) += spi-s3c24xx-hw.o
spi-s3c24xx-hw-y := spi-s3c24xx.o
......@@ -70,12 +71,14 @@ obj-$(CONFIG_SPI_SH_HSPI) += spi-sh-hspi.o
obj-$(CONFIG_SPI_SH_MSIOF) += spi-sh-msiof.o
obj-$(CONFIG_SPI_SH_SCI) += spi-sh-sci.o
obj-$(CONFIG_SPI_SIRF) += spi-sirf.o
obj-$(CONFIG_SPI_SUN4I) += spi-sun4i.o
obj-$(CONFIG_SPI_SUN6I) += spi-sun6i.o
obj-$(CONFIG_SPI_TEGRA114) += spi-tegra114.o
obj-$(CONFIG_SPI_TEGRA20_SFLASH) += spi-tegra20-sflash.o
obj-$(CONFIG_SPI_TEGRA20_SLINK) += spi-tegra20-slink.o
obj-$(CONFIG_SPI_TI_SSP) += spi-ti-ssp.o
obj-$(CONFIG_SPI_TLE62X0) += spi-tle62x0.o
obj-$(CONFIG_SPI_TOPCLIFF_PCH) += spi-topcliff-pch.o
obj-$(CONFIG_SPI_TXX9) += spi-txx9.o
obj-$(CONFIG_SPI_XCOMM) += spi-xcomm.o
obj-$(CONFIG_SPI_XILINX) += spi-xilinx.o
obj-$(CONFIG_SPI_XTENSA_XTFPGA) += spi-xtensa-xtfpga.o
drivers/spi/spi-altera.c
View file @ 09c0998e
......@@ -13,7 +13,6 @@
* published by the Free Software Foundation.
*/
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/errno.h>
#include <linux/module.h>
......@@ -200,7 +199,6 @@ static irqreturn_t altera_spi_irq(int irq, void *dev)
static int altera_spi_probe(struct platform_device *pdev)
{
struct altera_spi_platform_data *platp = dev_get_platdata(&pdev->dev);
struct altera_spi *hw;
struct spi_master *master;
struct resource *res;
......@@ -214,6 +212,8 @@ static int altera_spi_probe(struct platform_device *pdev)
master->bus_num = pdev->id;
master->num_chipselect = 16;
master->mode_bits = SPI_CS_HIGH;
master->bits_per_word_mask = SPI_BPW_RANGE_MASK(1, 16);
master->dev.of_node = pdev->dev.of_node;
hw = spi_master_get_devdata(master);
platform_set_drvdata(pdev, hw);
......@@ -245,9 +245,6 @@ static int altera_spi_probe(struct platform_device *pdev)
if (err)
goto exit;
}
/* find platform data */
if (!platp)
hw->bitbang.master->dev.of_node = pdev->dev.of_node;
/* register our spi controller */
err = spi_bitbang_start(&hw->bitbang);
......
drivers/spi/spi-ath79.c
View file @ 09c0998e
......@@ -14,7 +14,6 @@
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/spinlock.h>
#include <linux/workqueue.h>
......
drivers/spi/spi-atmel.c
View file @ 09c0998e
......@@ -9,7 +9,6 @@
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/clk.h>
#include <linux/module.h>
#include <linux/platform_device.h>
......@@ -26,6 +25,7 @@
#include <linux/io.h>
#include <linux/gpio.h>
#include <linux/pinctrl/consumer.h>
/* SPI register offsets */
#define SPI_CR 0x0000
......@@ -993,13 +993,6 @@ static int atmel_spi_setup(struct spi_device *spi)
as = spi_master_get_devdata(spi->master);
if (spi->chip_select > spi->master->num_chipselect) {
dev_dbg(&spi->dev,
"setup: invalid chipselect %u (%u defined)\n",
spi->chip_select, spi->master->num_chipselect);
return -EINVAL;
}
/* see notes above re chipselect */
if (!atmel_spi_is_v2(as)
&& spi->chip_select == 0
......@@ -1087,14 +1080,6 @@ static int atmel_spi_one_transfer(struct spi_master *master,
}
}
if (xfer->bits_per_word > 8) {
if (xfer->len % 2) {
dev_dbg(&spi->dev,
"buffer len should be 16 bits aligned\n");
return -EINVAL;
}
}
/*
* DMA map early, for performance (empties dcache ASAP) and
* better fault reporting.
......@@ -1221,9 +1206,6 @@ static int atmel_spi_transfer_one_message(struct spi_master *master,
dev_dbg(&spi->dev, "new message %p submitted for %s\n",
msg, dev_name(&spi->dev));
if (unlikely(list_empty(&msg->transfers)))
return -EINVAL;
atmel_spi_lock(as);
cs_activate(as, spi);
......@@ -1244,10 +1226,10 @@ static int atmel_spi_transfer_one_message(struct spi_master *master,
list_for_each_entry(xfer, &msg->transfers, transfer_list) {
dev_dbg(&spi->dev,
" xfer %p: len %u tx %p/%08x rx %p/%08x\n",
" xfer %p: len %u tx %p/%pad rx %p/%pad\n",
xfer, xfer->len,
xfer->tx_buf, xfer->tx_dma,
xfer->rx_buf, xfer->rx_dma);
xfer->tx_buf, &xfer->tx_dma,
xfer->rx_buf, &xfer->rx_dma);
}
msg_done:
......@@ -1303,6 +1285,9 @@ static int atmel_spi_probe(struct platform_device *pdev)
struct spi_master *master;
struct atmel_spi *as;
/* Select default pin state */
pinctrl_pm_select_default_state(&pdev->dev);
regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!regs)
return -ENXIO;
......@@ -1465,6 +1450,9 @@ static int atmel_spi_suspend(struct device *dev)
}
clk_disable_unprepare(as->clk);
pinctrl_pm_select_sleep_state(dev);
return 0;
}
......@@ -1474,6 +1462,8 @@ static int atmel_spi_resume(struct device *dev)
struct atmel_spi *as = spi_master_get_devdata(master);
int ret;
pinctrl_pm_select_default_state(dev);
clk_prepare_enable(as->clk);
/* Start the queue running */
......
drivers/spi/spi-au1550.c
View file @ 09c0998e
......@@ -55,8 +55,6 @@ struct au1550_spi {
volatile psc_spi_t __iomem *regs;
int irq;
unsigned freq_max;
unsigned freq_min;
unsigned len;
unsigned tx_count;
......@@ -248,11 +246,8 @@ static int au1550_spi_setupxfer(struct spi_device *spi, struct spi_transfer *t)
hz = t->speed_hz;
}
if (hz > spi->max_speed_hz || hz > hw->freq_max || hz < hw->freq_min) {
dev_err(&spi->dev, "setupxfer: clock rate=%d out of range\n",
hz);
if (!hz)
return -EINVAL;
}
au1550_spi_bits_handlers_set(hw, spi->bits_per_word);
......@@ -287,23 +282,6 @@ static int au1550_spi_setupxfer(struct spi_device *spi, struct spi_transfer *t)
return 0;
}
static int au1550_spi_setup(struct spi_device *spi)
{
struct au1550_spi *hw = spi_master_get_devdata(spi->master);
if (spi->max_speed_hz == 0)
spi->max_speed_hz = hw->freq_max;
if (spi->max_speed_hz > hw->freq_max
|| spi->max_speed_hz < hw->freq_min)
return -EINVAL;
/*
* NOTE: cannot change speed and other hw settings immediately,
* otherwise sharing of spi bus is not possible,
* so do not call setupxfer(spi, NULL) here
*/
return 0;
}
/*
* for dma spi transfers, we have to setup rx channel, otherwise there is
* no reliable way how to recognize that spi transfer is done
......@@ -838,7 +816,6 @@ static int au1550_spi_probe(struct platform_device *pdev)
hw->bitbang.master = hw->master;
hw->bitbang.setup_transfer = au1550_spi_setupxfer;
hw->bitbang.chipselect = au1550_spi_chipsel;
hw->bitbang.master->setup = au1550_spi_setup;
hw->bitbang.txrx_bufs = au1550_spi_txrx_bufs;
if (hw->usedma) {
......@@ -909,8 +886,9 @@ static int au1550_spi_probe(struct platform_device *pdev)
{
int min_div = (2 << 0) * (2 * (4 + 1));
int max_div = (2 << 3) * (2 * (63 + 1));
hw->freq_max = hw->pdata->mainclk_hz / min_div;
hw->freq_min = hw->pdata->mainclk_hz / (max_div + 1) + 1;
master->max_speed_hz = hw->pdata->mainclk_hz / min_div;
master->min_speed_hz =
hw->pdata->mainclk_hz / (max_div + 1) + 1;
}
au1550_spi_setup_psc_as_spi(hw);
......
drivers/spi/spi-bcm2835.c
View file @ 09c0998e
......@@ -315,7 +315,6 @@ static int bcm2835_spi_probe(struct platform_device *pdev)
master->mode_bits = BCM2835_SPI_MODE_BITS;
master->bits_per_word_mask = SPI_BPW_MASK(8);
master->bus_num = -1;
master->num_chipselect = 3;
master->transfer_one_message = bcm2835_spi_transfer_one;
master->dev.of_node = pdev->dev.of_node;
......
drivers/spi/spi-bcm63xx-hsspi.c
View file @ 09c0998e
......@@ -180,7 +180,7 @@ static int bcm63xx_hsspi_do_txrx(struct spi_device *spi, struct spi_transfer *t)
while (pending > 0) {
int curr_step = min_t(int, step_size, pending);
init_completion(&bs->done);
reinit_completion(&bs->done);
if (tx) {
memcpy_toio(bs->fifo + HSSPI_OPCODE_LEN, tx, curr_step);
tx += curr_step;
......@@ -369,6 +369,7 @@ static int bcm63xx_hsspi_probe(struct platform_device *pdev)
bs->fifo = (u8 __iomem *)(bs->regs + HSSPI_FIFO_REG(0));
mutex_init(&bs->bus_mutex);
init_completion(&bs->done);
master->bus_num = HSSPI_BUS_NUM;
master->num_chipselect = 8;
......@@ -453,9 +454,8 @@ static int bcm63xx_hsspi_resume(struct device *dev)
}
#endif
static const struct dev_pm_ops bcm63xx_hsspi_pm_ops = {
SET_SYSTEM_SLEEP_PM_OPS(bcm63xx_hsspi_suspend, bcm63xx_hsspi_resume)
};
static SIMPLE_DEV_PM_OPS(bcm63xx_hsspi_pm_ops, bcm63xx_hsspi_suspend,
bcm63xx_hsspi_resume);
static struct platform_driver bcm63xx_hsspi_driver = {
.driver = {
......
drivers/spi/spi-bcm63xx.c
View file @ 09c0998e
......@@ -20,7 +20,6 @@
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/clk.h>
#include <linux/io.h>
#include <linux/module.h>
......@@ -35,8 +34,6 @@
#include <bcm63xx_dev_spi.h>
#define PFX KBUILD_MODNAME
#define BCM63XX_SPI_MAX_PREPEND 15
struct bcm63xx_spi {
......@@ -169,7 +166,7 @@ static int bcm63xx_txrx_bufs(struct spi_device *spi, struct spi_transfer *first,
transfer_list);
}
init_completion(&bs->done);
reinit_completion(&bs->done);
/* Fill in the Message control register */
msg_ctl = (len << SPI_BYTE_CNT_SHIFT);
......@@ -353,6 +350,7 @@ static int bcm63xx_spi_probe(struct platform_device *pdev)
}
bs = spi_master_get_devdata(master);
init_completion(&bs->done);
platform_set_drvdata(pdev, master);
bs->pdev = pdev;
......
drivers/spi/spi-bfin-sport.c
View file @ 09c0998e
......@@ -8,7 +8,6 @@
* Licensed under the GPL-2 or later.
*/
#include <linux/init.h>
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/device.h>
......
drivers/spi/spi-bfin-v3.c
View file @ 09c0998e
......@@ -822,7 +822,8 @@ static int bfin_spi_probe(struct platform_device *pdev)
master->cleanup = bfin_spi_cleanup;
master->setup = bfin_spi_setup;
master->transfer_one_message = bfin_spi_transfer_one_message;
master->bits_per_word_mask = BIT(32 - 1) | BIT(16 - 1) | BIT(8 - 1);
master->bits_per_word_mask = SPI_BPW_MASK(32) | SPI_BPW_MASK(16) |
SPI_BPW_MASK(8);
drv_data = spi_master_get_devdata(master);
drv_data->master = master;
......
drivers/spi/spi-bfin5xx.c
View file @ 09c0998e
......@@ -350,7 +350,6 @@ static void *bfin_spi_next_transfer(struct bfin_spi_master_data *drv_data)
static void bfin_spi_giveback(struct bfin_spi_master_data *drv_data)
{
struct bfin_spi_slave_data *chip = drv_data->cur_chip;
struct spi_transfer *last_transfer;
unsigned long flags;
struct spi_message *msg;
......@@ -362,9 +361,6 @@ static void bfin_spi_giveback(struct bfin_spi_master_data *drv_data)
queue_work(drv_data->workqueue, &drv_data->pump_messages);
spin_unlock_irqrestore(&drv_data->lock, flags);
last_transfer = list_entry(msg->transfers.prev,
struct spi_transfer, transfer_list);
msg->state = NULL;
if (!drv_data->cs_change)
......@@ -1030,10 +1026,6 @@ static int bfin_spi_setup(struct spi_device *spi)
}
/* translate common spi framework into our register */
if (spi->mode & ~(SPI_CPOL | SPI_CPHA | SPI_LSB_FIRST)) {
dev_err(&spi->dev, "unsupported spi modes detected\n");
goto error;
}
if (spi->mode & SPI_CPOL)
chip->ctl_reg |= BIT_CTL_CPOL;
if (spi->mode & SPI_CPHA)
......
drivers/spi/spi-bitbang.c
View file @ 09c0998e
......@@ -16,7 +16,6 @@
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#include <linux/init.h>
#include <linux/spinlock.h>
#include <linux/workqueue.h>
#include <linux/interrupt.h>
......@@ -467,11 +466,9 @@ EXPORT_SYMBOL_GPL(spi_bitbang_start);
/**
* spi_bitbang_stop - stops the task providing spi communication
*/
int spi_bitbang_stop(struct spi_bitbang *bitbang)
void spi_bitbang_stop(struct spi_bitbang *bitbang)
{
spi_unregister_master(bitbang->master);
return 0;
}
EXPORT_SYMBOL_GPL(spi_bitbang_stop);
......
drivers/spi/spi-butterfly.c
View file @ 09c0998e
......@@ -309,7 +309,6 @@ static void butterfly_attach(struct parport *p)
static void butterfly_detach(struct parport *p)
{
struct butterfly *pp;
int status;
/* FIXME this global is ugly ... but, how to quickly get from
* the parport to the "struct butterfly" associated with it?
......@@ -321,7 +320,7 @@ static void butterfly_detach(struct parport *p)
butterfly = NULL;
/* stop() unregisters child devices too */
status = spi_bitbang_stop(&pp->bitbang);
spi_bitbang_stop(&pp->bitbang);
/* turn off VCC */
parport_write_data(pp->port, 0);
......
drivers/spi/spi-clps711x.c
View file @ 09c0998e
......@@ -11,158 +11,125 @@
#include <linux/io.h>
#include <linux/clk.h>
#include <linux/init.h>
#include <linux/gpio.h>
#include <linux/delay.h>
#include <linux/module.h>
#include <linux/interrupt.h>
#include <linux/platform_device.h>
#include <linux/regmap.h>
#include <linux/mfd/syscon.h>
#include <linux/mfd/syscon/clps711x.h>
#include <linux/spi/spi.h>
#include <linux/platform_data/spi-clps711x.h>
#include <mach/hardware.h>
#define DRIVER_NAME "spi-clps711x"
struct spi_clps711x_data {
struct completion done;
#define SYNCIO_FRMLEN(x) ((x) << 8)
#define SYNCIO_TXFRMEN (1 << 14)
struct spi_clps711x_data {
void __iomem *syncio;
struct regmap *syscon;
struct regmap *syscon1;
struct clk *spi_clk;
u32 max_speed_hz;
u8 *tx_buf;
u8 *rx_buf;
int count;
unsigned int bpw;
int len;
int chipselect[0];
};
static int spi_clps711x_setup(struct spi_device *spi)
{
struct spi_clps711x_data *hw = spi_master_get_devdata(spi->master);
/* We are expect that SPI-device is not selected */
gpio_direction_output(hw->chipselect[spi->chip_select],
!(spi->mode & SPI_CS_HIGH));
gpio_direction_output(spi->cs_gpio, !(spi->mode & SPI_CS_HIGH));
return 0;
}
static void spi_clps711x_setup_mode(struct spi_device *spi)
{
/* Setup edge for transfer */
if (spi->mode & SPI_CPHA)
clps_writew(clps_readw(SYSCON3) | SYSCON3_ADCCKNSEN, SYSCON3);
else
clps_writew(clps_readw(SYSCON3) & ~SYSCON3_ADCCKNSEN, SYSCON3);
}
static int spi_clps711x_setup_xfer(struct spi_device *spi,
struct spi_transfer *xfer)
static void spi_clps711x_setup_xfer(struct spi_device *spi,
struct spi_transfer *xfer)
{
u32 speed = xfer->speed_hz ? : spi->max_speed_hz;
u8 bpw = xfer->bits_per_word;
struct spi_clps711x_data *hw = spi_master_get_devdata(spi->master);
if (bpw != 8) {
dev_err(&spi->dev, "Unsupported master bus width %i\n", bpw);
return -EINVAL;
}
struct spi_master *master = spi->master;
struct spi_clps711x_data *hw = spi_master_get_devdata(master);
/* Setup SPI frequency divider */
if (!speed || (speed >= hw->max_speed_hz))
clps_writel((clps_readl(SYSCON1) & ~SYSCON1_ADCKSEL_MASK) |
SYSCON1_ADCKSEL(3), SYSCON1);
else if (speed >= (hw->max_speed_hz / 2))
clps_writel((clps_readl(SYSCON1) & ~SYSCON1_ADCKSEL_MASK) |
SYSCON1_ADCKSEL(2), SYSCON1);
else if (speed >= (hw->max_speed_hz / 8))
clps_writel((clps_readl(SYSCON1) & ~SYSCON1_ADCKSEL_MASK) |
SYSCON1_ADCKSEL(1), SYSCON1);
if (xfer->speed_hz >= master->max_speed_hz)
regmap_update_bits(hw->syscon1, SYSCON_OFFSET,
SYSCON1_ADCKSEL_MASK, SYSCON1_ADCKSEL(3));
else if (xfer->speed_hz >= (master->max_speed_hz / 2))
regmap_update_bits(hw->syscon1, SYSCON_OFFSET,
SYSCON1_ADCKSEL_MASK, SYSCON1_ADCKSEL(2));
else if (xfer->speed_hz >= (master->max_speed_hz / 8))
regmap_update_bits(hw->syscon1, SYSCON_OFFSET,
SYSCON1_ADCKSEL_MASK, SYSCON1_ADCKSEL(1));
else
clps_writel((clps_readl(SYSCON1) & ~SYSCON1_ADCKSEL_MASK) |
SYSCON1_ADCKSEL(0), SYSCON1);
return 0;
regmap_update_bits(hw->syscon1, SYSCON_OFFSET,
SYSCON1_ADCKSEL_MASK, SYSCON1_ADCKSEL(0));
}
static int spi_clps711x_transfer_one_message(struct spi_master *master,
struct spi_message *msg)
static int spi_clps711x_prepare_message(struct spi_master *master,
struct spi_message *msg)
{
struct spi_clps711x_data *hw = spi_master_get_devdata(master);
struct spi_transfer *xfer;
int status = 0, cs = hw->chipselect[msg->spi->chip_select];
u32 data;
spi_clps711x_setup_mode(msg->spi);
list_for_each_entry(xfer, &msg->transfers, transfer_list) {
if (spi_clps711x_setup_xfer(msg->spi, xfer)) {
status = -EINVAL;
goto out_xfr;
}
struct spi_device *spi = msg->spi;
gpio_set_value(cs, !!(msg->spi->mode & SPI_CS_HIGH));
reinit_completion(&hw->done);
hw->count = 0;
hw->len = xfer->len;
hw->tx_buf = (u8 *)xfer->tx_buf;
hw->rx_buf = (u8 *)xfer->rx_buf;
/* Initiate transfer */
data = hw->tx_buf ? hw->tx_buf[hw->count] : 0;
clps_writel(data | SYNCIO_FRMLEN(8) | SYNCIO_TXFRMEN, SYNCIO);
wait_for_completion(&hw->done);
/* Setup mode for transfer */
return regmap_update_bits(hw->syscon, SYSCON_OFFSET, SYSCON3_ADCCKNSEN,
(spi->mode & SPI_CPHA) ?
SYSCON3_ADCCKNSEN : 0);
}
if (xfer->delay_usecs)
udelay(xfer->delay_usecs);
static int spi_clps711x_transfer_one(struct spi_master *master,
struct spi_device *spi,
struct spi_transfer *xfer)
{
struct spi_clps711x_data *hw = spi_master_get_devdata(master);
u8 data;
if (xfer->cs_change ||
list_is_last(&xfer->transfer_list, &msg->transfers))
gpio_set_value(cs, !(msg->spi->mode & SPI_CS_HIGH));
spi_clps711x_setup_xfer(spi, xfer);
msg->actual_length += xfer->len;
}
hw->len = xfer->len;
hw->bpw = xfer->bits_per_word;
hw->tx_buf = (u8 *)xfer->tx_buf;
hw->rx_buf = (u8 *)xfer->rx_buf;
out_xfr:
msg->status = status;
spi_finalize_current_message(master);
/* Initiate transfer */
data = hw->tx_buf ? *hw->tx_buf++ : 0;
writel(data | SYNCIO_FRMLEN(hw->bpw) | SYNCIO_TXFRMEN, hw->syncio);
return 0;
return 1;
}
static irqreturn_t spi_clps711x_isr(int irq, void *dev_id)
{
struct spi_clps711x_data *hw = (struct spi_clps711x_data *)dev_id;
u32 data;
struct spi_master *master = dev_id;
struct spi_clps711x_data *hw = spi_master_get_devdata(master);
u8 data;
/* Handle RX */
data = clps_readb(SYNCIO);
data = readb(hw->syncio);
if (hw->rx_buf)
hw->rx_buf[hw->count] = (u8)data;
hw->count++;
*hw->rx_buf++ = data;
/* Handle TX */
if (hw->count < hw->len) {
data = hw->tx_buf ? hw->tx_buf[hw->count] : 0;
clps_writel(data | SYNCIO_FRMLEN(8) | SYNCIO_TXFRMEN, SYNCIO);
if (--hw->len > 0) {
data = hw->tx_buf ? *hw->tx_buf++ : 0;
writel(data | SYNCIO_FRMLEN(hw->bpw) | SYNCIO_TXFRMEN,
hw->syncio);
} else
complete(&hw->done);
spi_finalize_current_transfer(master);
return IRQ_HANDLED;
}
static int spi_clps711x_probe(struct platform_device *pdev)
{
int i, ret;
struct spi_master *master;
struct spi_clps711x_data *hw;
struct spi_clps711x_pdata *pdata = dev_get_platdata(&pdev->dev);
struct spi_master *master;
struct resource *res;
int i, irq, ret;
if (!pdata) {
dev_err(&pdev->dev, "No platform data supplied\n");
......@@ -174,33 +141,37 @@ static int spi_clps711x_probe(struct platform_device *pdev)
return -EINVAL;
}
master = spi_alloc_master(&pdev->dev,
sizeof(struct spi_clps711x_data) +
sizeof(int) * pdata->num_chipselect);
if (!master) {
dev_err(&pdev->dev, "SPI allocating memory error\n");
irq = platform_get_irq(pdev, 0);
if (irq < 0)
return irq;
master = spi_alloc_master(&pdev->dev, sizeof(*hw));
if (!master)
return -ENOMEM;
master->cs_gpios = devm_kzalloc(&pdev->dev, sizeof(int) *
pdata->num_chipselect, GFP_KERNEL);
if (!master->cs_gpios) {
ret = -ENOMEM;
goto err_out;
}
master->bus_num = pdev->id;
master->mode_bits = SPI_CPHA | SPI_CS_HIGH;
master->bits_per_word_mask = SPI_BPW_MASK(8);
master->bits_per_word_mask = SPI_BPW_RANGE_MASK(1, 8);
master->num_chipselect = pdata->num_chipselect;
master->setup = spi_clps711x_setup;
master->transfer_one_message = spi_clps711x_transfer_one_message;
master->prepare_message = spi_clps711x_prepare_message;
master->transfer_one = spi_clps711x_transfer_one;
hw = spi_master_get_devdata(master);
for (i = 0; i < master->num_chipselect; i++) {
hw->chipselect[i] = pdata->chipselect[i];
if (!gpio_is_valid(hw->chipselect[i])) {
dev_err(&pdev->dev, "Invalid CS GPIO %i\n", i);
ret = -EINVAL;
goto err_out;
}
if (devm_gpio_request(&pdev->dev, hw->chipselect[i], NULL)) {
master->cs_gpios[i] = pdata->chipselect[i];
ret = devm_gpio_request(&pdev->dev, master->cs_gpios[i],
DRIVER_NAME);
if (ret) {
dev_err(&pdev->dev, "Can't get CS GPIO %i\n", i);
ret = -EINVAL;
goto err_out;
}
}
......@@ -211,29 +182,45 @@ static int spi_clps711x_probe(struct platform_device *pdev)
ret = PTR_ERR(hw->spi_clk);
goto err_out;
}
hw->max_speed_hz = clk_get_rate(hw->spi_clk);
master->max_speed_hz = clk_get_rate(hw->spi_clk);
init_completion(&hw->done);
platform_set_drvdata(pdev, master);
hw->syscon = syscon_regmap_lookup_by_pdevname("syscon.3");
if (IS_ERR(hw->syscon)) {
ret = PTR_ERR(hw->syscon);
goto err_out;
}
hw->syscon1 = syscon_regmap_lookup_by_pdevname("syscon.1");
if (IS_ERR(hw->syscon1)) {
ret = PTR_ERR(hw->syscon1);
goto err_out;
}
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
hw->syncio = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(hw->syncio)) {
ret = PTR_ERR(hw->syncio);
goto err_out;
}
/* Disable extended mode due hardware problems */
clps_writew(clps_readw(SYSCON3) & ~SYSCON3_ADCCON, SYSCON3);
regmap_update_bits(hw->syscon, SYSCON_OFFSET, SYSCON3_ADCCON, 0);
/* Clear possible pending interrupt */
clps_readl(SYNCIO);
readl(hw->syncio);
ret = devm_request_irq(&pdev->dev, IRQ_SSEOTI, spi_clps711x_isr, 0,
dev_name(&pdev->dev), hw);
if (ret) {
dev_err(&pdev->dev, "Can't request IRQ\n");
ret = devm_request_irq(&pdev->dev, irq, spi_clps711x_isr, 0,
dev_name(&pdev->dev), master);
if (ret)
goto err_out;
}
ret = devm_spi_register_master(&pdev->dev, master);
if (!ret) {
dev_info(&pdev->dev,
"SPI bus driver initialized. Master clock %u Hz\n",
hw->max_speed_hz);
master->max_speed_hz);
return 0;
}
......
drivers/spi/spi-coldfire-qspi.c
View file @ 09c0998e
......@@ -77,8 +77,6 @@ struct mcfqspi {
struct mcfqspi_cs_control *cs_control;
wait_queue_head_t waitq;
struct device *dev;
};
static void mcfqspi_wr_qmr(struct mcfqspi *mcfqspi, u16 val)
......@@ -135,13 +133,13 @@ static void mcfqspi_cs_deselect(struct mcfqspi *mcfqspi, u8 chip_select,
static int mcfqspi_cs_setup(struct mcfqspi *mcfqspi)
{
return (mcfqspi->cs_control && mcfqspi->cs_control->setup) ?
return (mcfqspi->cs_control->setup) ?
mcfqspi->cs_control->setup(mcfqspi->cs_control) : 0;
}
static void mcfqspi_cs_teardown(struct mcfqspi *mcfqspi)
{
if (mcfqspi->cs_control && mcfqspi->cs_control->teardown)
if (mcfqspi->cs_control->teardown)
mcfqspi->cs_control->teardown(mcfqspi->cs_control);
}
......@@ -300,68 +298,45 @@ static void mcfqspi_transfer_msg16(struct mcfqspi *mcfqspi, unsigned count,
}
}
static int mcfqspi_transfer_one_message(struct spi_master *master,
struct spi_message *msg)
static void mcfqspi_set_cs(struct spi_device *spi, bool enable)
{
struct mcfqspi *mcfqspi = spi_master_get_devdata(master);
struct spi_device *spi = msg->spi;
struct spi_transfer *t;
int status = 0;
list_for_each_entry(t, &msg->transfers, transfer_list) {
bool cs_high = spi->mode & SPI_CS_HIGH;
u16 qmr = MCFQSPI_QMR_MSTR;
qmr |= t->bits_per_word << 10;
if (spi->mode & SPI_CPHA)
qmr |= MCFQSPI_QMR_CPHA;
if (spi->mode & SPI_CPOL)
qmr |= MCFQSPI_QMR_CPOL;
if (t->speed_hz)
qmr |= mcfqspi_qmr_baud(t->speed_hz);
else
qmr |= mcfqspi_qmr_baud(spi->max_speed_hz);
mcfqspi_wr_qmr(mcfqspi, qmr);
struct mcfqspi *mcfqspi = spi_master_get_devdata(spi->master);
bool cs_high = spi->mode & SPI_CS_HIGH;
if (enable)
mcfqspi_cs_select(mcfqspi, spi->chip_select, cs_high);
else
mcfqspi_cs_deselect(mcfqspi, spi->chip_select, cs_high);
}
mcfqspi_wr_qir(mcfqspi, MCFQSPI_QIR_SPIFE);
if (t->bits_per_word == 8)
mcfqspi_transfer_msg8(mcfqspi, t->len, t->tx_buf,
t->rx_buf);
else
mcfqspi_transfer_msg16(mcfqspi, t->len / 2, t->tx_buf,
t->rx_buf);
mcfqspi_wr_qir(mcfqspi, 0);
if (t->delay_usecs)
udelay(t->delay_usecs);
if (t->cs_change) {
if (!list_is_last(&t->transfer_list, &msg->transfers))
mcfqspi_cs_deselect(mcfqspi, spi->chip_select,
cs_high);
} else {
if (list_is_last(&t->transfer_list, &msg->transfers))
mcfqspi_cs_deselect(mcfqspi, spi->chip_select,
cs_high);
}
msg->actual_length += t->len;
}
msg->status = status;
spi_finalize_current_message(master);
return status;
static int mcfqspi_transfer_one(struct spi_master *master,
struct spi_device *spi,
struct spi_transfer *t)
{
struct mcfqspi *mcfqspi = spi_master_get_devdata(master);
u16 qmr = MCFQSPI_QMR_MSTR;
qmr |= t->bits_per_word << 10;
if (spi->mode & SPI_CPHA)
qmr |= MCFQSPI_QMR_CPHA;
if (spi->mode & SPI_CPOL)
qmr |= MCFQSPI_QMR_CPOL;
qmr |= mcfqspi_qmr_baud(t->speed_hz);
mcfqspi_wr_qmr(mcfqspi, qmr);
mcfqspi_wr_qir(mcfqspi, MCFQSPI_QIR_SPIFE);
if (t->bits_per_word == 8)
mcfqspi_transfer_msg8(mcfqspi, t->len, t->tx_buf, t->rx_buf);
else
mcfqspi_transfer_msg16(mcfqspi, t->len / 2, t->tx_buf,
t->rx_buf);
mcfqspi_wr_qir(mcfqspi, 0);
return 0;
}
static int mcfqspi_setup(struct spi_device *spi)
{
if (spi->chip_select >= spi->master->num_chipselect) {
dev_dbg(&spi->dev, "%d chip select is out of range\n",
spi->chip_select);
return -EINVAL;
}
mcfqspi_cs_deselect(spi_master_get_devdata(spi->master),
spi->chip_select, spi->mode & SPI_CS_HIGH);
......@@ -388,6 +363,11 @@ static int mcfqspi_probe(struct platform_device *pdev)
return -ENOENT;
}
if (!pdata->cs_control) {
dev_dbg(&pdev->dev, "pdata->cs_control is NULL\n");
return -EINVAL;
}
master = spi_alloc_master(&pdev->dev, sizeof(*mcfqspi));
if (master == NULL) {
dev_dbg(&pdev->dev, "spi_alloc_master failed\n");
......@@ -436,12 +416,12 @@ static int mcfqspi_probe(struct platform_device *pdev)
}
init_waitqueue_head(&mcfqspi->waitq);
mcfqspi->dev = &pdev->dev;
master->mode_bits = SPI_CS_HIGH | SPI_CPOL | SPI_CPHA;
master->bits_per_word_mask = SPI_BPW_RANGE_MASK(8, 16);
master->setup = mcfqspi_setup;
master->transfer_one_message = mcfqspi_transfer_one_message;
master->set_cs = mcfqspi_set_cs;
master->transfer_one = mcfqspi_transfer_one;
master->auto_runtime_pm = true;
platform_set_drvdata(pdev, master);
......@@ -451,7 +431,7 @@ static int mcfqspi_probe(struct platform_device *pdev)
dev_dbg(&pdev->dev, "spi_register_master failed\n");
goto fail2;
}
pm_runtime_enable(mcfqspi->dev);
pm_runtime_enable(&pdev->dev);
dev_info(&pdev->dev, "Coldfire QSPI bus driver\n");
......@@ -473,9 +453,8 @@ static int mcfqspi_remove(struct platform_device *pdev)
{
struct spi_master *master = platform_get_drvdata(pdev);
struct mcfqspi *mcfqspi = spi_master_get_devdata(master);
struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
pm_runtime_disable(mcfqspi->dev);
pm_runtime_disable(&pdev->dev);
/* disable the hardware (set the baud rate to 0) */
mcfqspi_wr_qmr(mcfqspi, MCFQSPI_QMR_MSTR);
......@@ -490,8 +469,11 @@ static int mcfqspi_suspend(struct device *dev)
{
struct spi_master *master = dev_get_drvdata(dev);
struct mcfqspi *mcfqspi = spi_master_get_devdata(master);
int ret;
spi_master_suspend(master);
ret = spi_master_suspend(master);
if (ret)
return ret;
clk_disable(mcfqspi->clk);
......@@ -503,11 +485,9 @@ static int mcfqspi_resume(struct device *dev)
struct spi_master *master = dev_get_drvdata(dev);
struct mcfqspi *mcfqspi = spi_master_get_devdata(master);
spi_master_resume(master);
clk_enable(mcfqspi->clk);
return 0;
return spi_master_resume(master);
}
#endif
......
drivers/spi/spi-davinci.c
View file @ 09c0998e
......@@ -802,8 +802,7 @@ static int spi_davinci_get_pdata(struct platform_device *pdev,
pdata = &dspi->pdata;
pdata->version = SPI_VERSION_1;
match = of_match_device(of_match_ptr(davinci_spi_of_match),
&pdev->dev);
match = of_match_device(davinci_spi_of_match, &pdev->dev);
if (!match)
return -ENODEV;
......@@ -824,7 +823,6 @@ static int spi_davinci_get_pdata(struct platform_device *pdev,
return 0;
}
#else
#define davinci_spi_of_match NULL
static struct davinci_spi_platform_data
*spi_davinci_get_pdata(struct platform_device *pdev,
struct davinci_spi *dspi)
......@@ -864,10 +862,6 @@ static int davinci_spi_probe(struct platform_device *pdev)
platform_set_drvdata(pdev, master);
dspi = spi_master_get_devdata(master);
if (dspi == NULL) {
ret = -ENOENT;
goto free_master;
}
if (dev_get_platdata(&pdev->dev)) {
pdata = dev_get_platdata(&pdev->dev);
......@@ -908,10 +902,6 @@ static int davinci_spi_probe(struct platform_device *pdev)
goto free_master;
dspi->bitbang.master = master;
if (dspi->bitbang.master == NULL) {
ret = -ENODEV;
goto free_master;
}
dspi->clk = devm_clk_get(&pdev->dev, NULL);
if (IS_ERR(dspi->clk)) {
......@@ -1040,7 +1030,7 @@ static struct platform_driver davinci_spi_driver = {
.driver = {
.name = "spi_davinci",
.owner = THIS_MODULE,
.of_match_table = davinci_spi_of_match,
.of_match_table = of_match_ptr(davinci_spi_of_match),
},
.probe = davinci_spi_probe,
.remove = davinci_spi_remove,
......
drivers/spi/spi-dw-mmio.c
View file @ 09c0998e
......@@ -66,7 +66,7 @@ static int dw_spi_mmio_probe(struct platform_device *pdev)
if (ret)
return ret;
dws->bus_num = 0;
dws->bus_num = pdev->id;
dws->num_cs = 4;
dws->max_freq = clk_get_rate(dwsmmio->clk);
......
drivers/spi/spi-dw.c
View file @ 09c0998e
......@@ -276,8 +276,7 @@ static void giveback(struct dw_spi *dws)
queue_work(dws->workqueue, &dws->pump_messages);
spin_unlock_irqrestore(&dws->lock, flags);
last_transfer = list_entry(msg->transfers.prev,
struct spi_transfer,
last_transfer = list_last_entry(&msg->transfers, struct spi_transfer,
transfer_list);
if (!last_transfer->cs_change && dws->cs_control)
......@@ -439,12 +438,6 @@ static void pump_transfers(unsigned long data)
if (transfer->speed_hz != speed) {
speed = transfer->speed_hz;
if (speed > dws->max_freq) {
printk(KERN_ERR "MRST SPI0: unsupported"
"freq: %dHz\n", speed);
message->status = -EIO;
goto early_exit;
}
/* clk_div doesn't support odd number */
clk_div = dws->max_freq / speed;
......@@ -671,12 +664,6 @@ static int dw_spi_setup(struct spi_device *spi)
return 0;
}
static void dw_spi_cleanup(struct spi_device *spi)
{
struct chip_data *chip = spi_get_ctldata(spi);
kfree(chip);
}
static int init_queue(struct dw_spi *dws)
{
INIT_LIST_HEAD(&dws->queue);
......@@ -806,9 +793,9 @@ int dw_spi_add_host(struct device *dev, struct dw_spi *dws)
master->bits_per_word_mask = SPI_BPW_MASK(8) | SPI_BPW_MASK(16);
master->bus_num = dws->bus_num;
master->num_chipselect = dws->num_cs;
master->cleanup = dw_spi_cleanup;
master->setup = dw_spi_setup;
master->transfer = dw_spi_transfer;
master->max_speed_hz = dws->max_freq;
/* Basic HW init */
spi_hw_init(dws);
......
drivers/spi/spi-efm32.c
View file @ 09c0998e
......@@ -198,7 +198,7 @@ static int efm32_spi_txrx_bufs(struct spi_device *spi, struct spi_transfer *t)
efm32_spi_filltx(ddata);
init_completion(&ddata->done);
reinit_completion(&ddata->done);
efm32_spi_write32(ddata, REG_IF_TXBL | REG_IF_RXDATAV, REG_IEN);
......@@ -287,17 +287,17 @@ static u32 efm32_spi_get_configured_location(struct efm32_spi_ddata *ddata)
return (reg & REG_ROUTE_LOCATION__MASK) >> __ffs(REG_ROUTE_LOCATION__MASK);
}
static int efm32_spi_probe_dt(struct platform_device *pdev,
static void efm32_spi_probe_dt(struct platform_device *pdev,
struct spi_master *master, struct efm32_spi_ddata *ddata)
{
struct device_node *np = pdev->dev.of_node;
u32 location;
int ret;
if (!np)
return 1;
ret = of_property_read_u32(np, "location", &location);
ret = of_property_read_u32(np, "efm32,location", &location);
if (ret)
/* fall back to old and (wrongly) generic property "location" */
ret = of_property_read_u32(np, "location", &location);
if (!ret) {
dev_dbg(&pdev->dev, "using location %u\n", location);
} else {
......@@ -308,11 +308,6 @@ static int efm32_spi_probe_dt(struct platform_device *pdev,
}
ddata->pdata.location = location;
/* spi core takes care about the bus number using an alias */
master->bus_num = -1;
return 0;
}
static int efm32_spi_probe(struct platform_device *pdev)
......@@ -322,9 +317,14 @@ static int efm32_spi_probe(struct platform_device *pdev)
int ret;
struct spi_master *master;
struct device_node *np = pdev->dev.of_node;
unsigned int num_cs, i;
int num_cs, i;
if (!np)
return -EINVAL;
num_cs = of_gpio_named_count(np, "cs-gpios");
if (num_cs < 0)
return num_cs;
master = spi_alloc_master(&pdev->dev,
sizeof(*ddata) + num_cs * sizeof(unsigned));
......@@ -349,6 +349,7 @@ static int efm32_spi_probe(struct platform_device *pdev)
ddata->bitbang.txrx_bufs = efm32_spi_txrx_bufs;
spin_lock_init(&ddata->lock);
init_completion(&ddata->done);
ddata->clk = devm_clk_get(&pdev->dev, NULL);
if (IS_ERR(ddata->clk)) {
......@@ -415,23 +416,7 @@ static int efm32_spi_probe(struct platform_device *pdev)
goto err;
}
ret = efm32_spi_probe_dt(pdev, master, ddata);
if (ret > 0) {
/* not created by device tree */
const struct efm32_spi_pdata *pdata =
dev_get_platdata(&pdev->dev);
if (pdata)
ddata->pdata = *pdata;
else
ddata->pdata.location =
efm32_spi_get_configured_location(ddata);
master->bus_num = pdev->id;
} else if (ret < 0) {
goto err_disable_clk;
}
efm32_spi_probe_dt(pdev, master, ddata);
efm32_spi_write32(ddata, 0, REG_IEN);
efm32_spi_write32(ddata, REG_ROUTE_TXPEN | REG_ROUTE_RXPEN |
......@@ -487,6 +472,9 @@ static int efm32_spi_remove(struct platform_device *pdev)
static const struct of_device_id efm32_spi_dt_ids[] = {
{
.compatible = "energymicro,efm32-spi",
}, {
/* doesn't follow the "vendor,device" scheme, don't use */
.compatible = "efm32,spi",
}, {
/* sentinel */
......
drivers/spi/spi-ep93xx.c
View file @ 09c0998e
......@@ -73,8 +73,6 @@
* @clk: clock for the controller
* @regs_base: pointer to ioremap()'d registers
* @sspdr_phys: physical address of the SSPDR register
* @min_rate: minimum clock rate (in Hz) supported by the controller
* @max_rate: maximum clock rate (in Hz) supported by the controller
* @wait: wait here until given transfer is completed
* @current_msg: message that is currently processed (or %NULL if none)
* @tx: current byte in transfer to transmit
......@@ -95,8 +93,6 @@ struct ep93xx_spi {
struct clk *clk;
void __iomem *regs_base;
unsigned long sspdr_phys;
unsigned long min_rate;
unsigned long max_rate;
struct completion wait;
struct spi_message *current_msg;
size_t tx;
......@@ -199,9 +195,9 @@ static void ep93xx_spi_disable_interrupts(const struct ep93xx_spi *espi)
* @div_scr: pointer to return the scr divider
*/
static int ep93xx_spi_calc_divisors(const struct ep93xx_spi *espi,
unsigned long rate,
u8 *div_cpsr, u8 *div_scr)
u32 rate, u8 *div_cpsr, u8 *div_scr)
{
struct spi_master *master = platform_get_drvdata(espi->pdev);
unsigned long spi_clk_rate = clk_get_rate(espi->clk);
int cpsr, scr;
......@@ -210,7 +206,7 @@ static int ep93xx_spi_calc_divisors(const struct ep93xx_spi *espi,
* controller. Note that minimum value is already checked in
* ep93xx_spi_transfer_one_message().
*/
rate = clamp(rate, espi->min_rate, espi->max_rate);
rate = clamp(rate, master->min_speed_hz, master->max_speed_hz);
/*
* Calculate divisors so that we can get speed according the
......@@ -735,13 +731,6 @@ static int ep93xx_spi_transfer_one_message(struct spi_master *master,
struct spi_message *msg)
{
struct ep93xx_spi *espi = spi_master_get_devdata(master);
struct spi_transfer *t;
/* first validate each transfer */
list_for_each_entry(t, &msg->transfers, transfer_list) {
if (t->speed_hz < espi->min_rate)
return -EINVAL;
}
msg->state = NULL;
msg->status = 0;
......@@ -917,8 +906,8 @@ static int ep93xx_spi_probe(struct platform_device *pdev)
* Calculate maximum and minimum supported clock rates
* for the controller.
*/
espi->max_rate = clk_get_rate(espi->clk) / 2;
espi->min_rate = clk_get_rate(espi->clk) / (254 * 256);
master->max_speed_hz = clk_get_rate(espi->clk) / 2;
master->min_speed_hz = clk_get_rate(espi->clk) / (254 * 256);
espi->pdev = pdev;
espi->sspdr_phys = res->start + SSPDR;
......
drivers/spi/spi-falcon.c
View file @ 09c0998e
......@@ -312,9 +312,6 @@ static int falcon_sflash_setup(struct spi_device *spi)
unsigned int i;
unsigned long flags;
if (spi->chip_select > 0)
return -ENODEV;
spin_lock_irqsave(&ebu_lock, flags);
if (spi->max_speed_hz >= CLOCK_100M) {
......@@ -422,9 +419,7 @@ static int falcon_sflash_probe(struct platform_device *pdev)
priv->master = master;
master->mode_bits = SPI_MODE_3;
master->num_chipselect = 1;
master->flags = SPI_MASTER_HALF_DUPLEX;
master->bus_num = -1;
master->setup = falcon_sflash_setup;
master->prepare_transfer_hardware = falcon_sflash_prepare_xfer;
master->transfer_one_message = falcon_sflash_xfer_one;
......
drivers/spi/spi-fsl-dspi.c
View file @ 09c0998e
......@@ -18,6 +18,7 @@
#include <linux/interrupt.h>
#include <linux/errno.h>
#include <linux/platform_device.h>
#include <linux/regmap.h>
#include <linux/sched.h>
#include <linux/delay.h>
#include <linux/io.h>
......@@ -108,11 +109,11 @@ struct fsl_dspi {
struct spi_bitbang bitbang;
struct platform_device *pdev;
void __iomem *base;
struct regmap *regmap;
int irq;
struct clk *clk;
struct clk *clk;
struct spi_transfer *cur_transfer;
struct spi_transfer *cur_transfer;
struct chip_data *cur_chip;
size_t len;
void *tx;
......@@ -123,24 +124,17 @@ struct fsl_dspi {
u8 cs;
u16 void_write_data;
wait_queue_head_t waitq;
u32 waitflags;
wait_queue_head_t waitq;
u32 waitflags;
};
static inline int is_double_byte_mode(struct fsl_dspi *dspi)
{
return ((readl(dspi->base + SPI_CTAR(dspi->cs)) & SPI_FRAME_BITS_MASK)
== SPI_FRAME_BITS(8)) ? 0 : 1;
}
unsigned int val;
static void set_bit_mode(struct fsl_dspi *dspi, unsigned char bits)
{
u32 temp;
regmap_read(dspi->regmap, SPI_CTAR(dspi->cs), &val);
temp = readl(dspi->base + SPI_CTAR(dspi->cs));
temp &= ~SPI_FRAME_BITS_MASK;
temp |= SPI_FRAME_BITS(bits);
writel(temp, dspi->base + SPI_CTAR(dspi->cs));
return ((val & SPI_FRAME_BITS_MASK) == SPI_FRAME_BITS(8)) ? 0 : 1;
}
static void hz_to_spi_baud(char *pbr, char *br, int speed_hz,
......@@ -188,7 +182,8 @@ static int dspi_transfer_write(struct fsl_dspi *dspi)
*/
if (tx_word && (dspi->len == 1)) {
dspi->dataflags |= TRAN_STATE_WORD_ODD_NUM;
set_bit_mode(dspi, 8);
regmap_update_bits(dspi->regmap, SPI_CTAR(dspi->cs),
SPI_FRAME_BITS_MASK, SPI_FRAME_BITS(8));
tx_word = 0;
}
......@@ -238,7 +233,8 @@ static int dspi_transfer_write(struct fsl_dspi *dspi)
dspi_pushr |= SPI_PUSHR_CTCNT; /* clear counter */
}
writel(dspi_pushr, dspi->base + SPI_PUSHR);
regmap_write(dspi->regmap, SPI_PUSHR, dspi_pushr);
tx_count++;
}
......@@ -253,17 +249,23 @@ static int dspi_transfer_read(struct fsl_dspi *dspi)
while ((dspi->rx < dspi->rx_end)
&& (rx_count < DSPI_FIFO_SIZE)) {
if (rx_word) {
unsigned int val;
if ((dspi->rx_end - dspi->rx) == 1)
break;
d = SPI_POPR_RXDATA(readl(dspi->base + SPI_POPR));
regmap_read(dspi->regmap, SPI_POPR, &val);
d = SPI_POPR_RXDATA(val);
if (!(dspi->dataflags & TRAN_STATE_RX_VOID))
*(u16 *)dspi->rx = d;
dspi->rx += 2;
} else {
d = SPI_POPR_RXDATA(readl(dspi->base + SPI_POPR));
unsigned int val;
regmap_read(dspi->regmap, SPI_POPR, &val);
d = SPI_POPR_RXDATA(val);
if (!(dspi->dataflags & TRAN_STATE_RX_VOID))
*(u8 *)dspi->rx = d;
dspi->rx++;
......@@ -295,13 +297,13 @@ static int dspi_txrx_transfer(struct spi_device *spi, struct spi_transfer *t)
if (!dspi->tx)
dspi->dataflags |= TRAN_STATE_TX_VOID;
writel(dspi->cur_chip->mcr_val, dspi->base + SPI_MCR);
writel(dspi->cur_chip->ctar_val, dspi->base + SPI_CTAR(dspi->cs));
writel(SPI_RSER_EOQFE, dspi->base + SPI_RSER);
regmap_write(dspi->regmap, SPI_MCR, dspi->cur_chip->mcr_val);
regmap_write(dspi->regmap, SPI_CTAR(dspi->cs), dspi->cur_chip->ctar_val);
regmap_write(dspi->regmap, SPI_RSER, SPI_RSER_EOQFE);
if (t->speed_hz)
writel(dspi->cur_chip->ctar_val,
dspi->base + SPI_CTAR(dspi->cs));
regmap_write(dspi->regmap, SPI_CTAR(dspi->cs),
dspi->cur_chip->ctar_val);
dspi_transfer_write(dspi);
......@@ -315,7 +317,9 @@ static int dspi_txrx_transfer(struct spi_device *spi, struct spi_transfer *t)
static void dspi_chipselect(struct spi_device *spi, int value)
{
struct fsl_dspi *dspi = spi_master_get_devdata(spi->master);
u32 pushr = readl(dspi->base + SPI_PUSHR);
unsigned int pushr;
regmap_read(dspi->regmap, SPI_PUSHR, &pushr);
switch (value) {
case BITBANG_CS_ACTIVE:
......@@ -326,7 +330,7 @@ static void dspi_chipselect(struct spi_device *spi, int value)
break;
}
writel(pushr, dspi->base + SPI_PUSHR);
regmap_write(dspi->regmap, SPI_PUSHR, pushr);
}
static int dspi_setup_transfer(struct spi_device *spi, struct spi_transfer *t)
......@@ -338,7 +342,8 @@ static int dspi_setup_transfer(struct spi_device *spi, struct spi_transfer *t)
/* Only alloc on first setup */
chip = spi_get_ctldata(spi);
if (chip == NULL) {
chip = kcalloc(1, sizeof(struct chip_data), GFP_KERNEL);
chip = devm_kzalloc(&spi->dev, sizeof(struct chip_data),
GFP_KERNEL);
if (!chip)
return -ENOMEM;
}
......@@ -349,7 +354,6 @@ static int dspi_setup_transfer(struct spi_device *spi, struct spi_transfer *t)
fmsz = spi->bits_per_word - 1;
} else {
pr_err("Invalid wordsize\n");
kfree(chip);
return -ENODEV;
}
......@@ -382,13 +386,15 @@ static irqreturn_t dspi_interrupt(int irq, void *dev_id)
{
struct fsl_dspi *dspi = (struct fsl_dspi *)dev_id;
writel(SPI_SR_EOQF, dspi->base + SPI_SR);
regmap_write(dspi->regmap, SPI_SR, SPI_SR_EOQF);
dspi_transfer_read(dspi);
if (!dspi->len) {
if (dspi->dataflags & TRAN_STATE_WORD_ODD_NUM)
set_bit_mode(dspi, 16);
regmap_update_bits(dspi->regmap, SPI_CTAR(dspi->cs),
SPI_FRAME_BITS_MASK, SPI_FRAME_BITS(16));
dspi->waitflags = 1;
wake_up_interruptible(&dspi->waitq);
} else {
......@@ -430,8 +436,13 @@ static int dspi_resume(struct device *dev)
}
#endif /* CONFIG_PM_SLEEP */
static const struct dev_pm_ops dspi_pm = {
SET_SYSTEM_SLEEP_PM_OPS(dspi_suspend, dspi_resume)
static SIMPLE_DEV_PM_OPS(dspi_pm, dspi_suspend, dspi_resume);
static struct regmap_config dspi_regmap_config = {
.reg_bits = 32,
.val_bits = 32,
.reg_stride = 4,
.max_register = 0x88,
};
static int dspi_probe(struct platform_device *pdev)
......@@ -440,6 +451,7 @@ static int dspi_probe(struct platform_device *pdev)
struct spi_master *master;
struct fsl_dspi *dspi;
struct resource *res;
void __iomem *base;
int ret = 0, cs_num, bus_num;
master = spi_alloc_master(&pdev->dev, sizeof(struct fsl_dspi));
......@@ -474,12 +486,24 @@ static int dspi_probe(struct platform_device *pdev)
master->bus_num = bus_num;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
dspi->base = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(dspi->base)) {
ret = PTR_ERR(dspi->base);
base = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(base)) {
ret = PTR_ERR(base);
goto out_master_put;
}
dspi_regmap_config.lock_arg = dspi;
dspi_regmap_config.val_format_endian =
of_property_read_bool(np, "big-endian")
? REGMAP_ENDIAN_BIG : REGMAP_ENDIAN_DEFAULT;
dspi->regmap = devm_regmap_init_mmio_clk(&pdev->dev, "dspi", base,
&dspi_regmap_config);
if (IS_ERR(dspi->regmap)) {
dev_err(&pdev->dev, "failed to init regmap: %ld\n",
PTR_ERR(dspi->regmap));
return PTR_ERR(dspi->regmap);
}
dspi->irq = platform_get_irq(pdev, 0);
if (dspi->irq < 0) {
dev_err(&pdev->dev, "can't get platform irq\n");
......
drivers/spi/spi-fsl-espi.c
View file @ 09c0998e
......@@ -219,13 +219,8 @@ static int fsl_espi_bufs(struct spi_device *spi, struct spi_transfer *t)
struct mpc8xxx_spi *mpc8xxx_spi = spi_master_get_devdata(spi->master);
struct fsl_espi_reg *reg_base = mpc8xxx_spi->reg_base;
unsigned int len = t->len;
u8 bits_per_word;
int ret;
bits_per_word = spi->bits_per_word;
if (t->bits_per_word)
bits_per_word = t->bits_per_word;
mpc8xxx_spi->len = t->len;
len = roundup(len, 4) / 4;
......
drivers/spi/spi-fsl-lib.c
View file @ 09c0998e
......@@ -200,7 +200,7 @@ int of_mpc8xxx_spi_probe(struct platform_device *ofdev)
const void *prop;
int ret = -ENOMEM;
pinfo = kzalloc(sizeof(*pinfo), GFP_KERNEL);
pinfo = devm_kzalloc(&ofdev->dev, sizeof(*pinfo), GFP_KERNEL);
if (!pinfo)
return -ENOMEM;
......@@ -215,15 +215,13 @@ int of_mpc8xxx_spi_probe(struct platform_device *ofdev)
pdata->sysclk = get_brgfreq();
if (pdata->sysclk == -1) {
pdata->sysclk = fsl_get_sys_freq();
if (pdata->sysclk == -1) {
ret = -ENODEV;
goto err;
}
if (pdata->sysclk == -1)
return -ENODEV;
}
#else
ret = of_property_read_u32(np, "clock-frequency", &pdata->sysclk);
if (ret)
goto err;
return ret;
#endif
prop = of_get_property(np, "mode", NULL);
......@@ -237,8 +235,4 @@ int of_mpc8xxx_spi_probe(struct platform_device *ofdev)
pdata->flags = SPI_CPM_MODE | SPI_CPM1;
return 0;
err:
kfree(pinfo);
return ret;
}
drivers/spi/spi-fsl-spi.c
View file @ 09c0998e
......@@ -239,12 +239,6 @@ static int fsl_spi_setup_transfer(struct spi_device *spi,
if (!bits_per_word)
bits_per_word = spi->bits_per_word;
/* Make sure its a bit width we support [4..16, 32] */
if ((bits_per_word < 4)
|| ((bits_per_word > 16) && (bits_per_word != 32))
|| (bits_per_word > mpc8xxx_spi->max_bits_per_word))
return -EINVAL;
if (!hz)
hz = spi->max_speed_hz;
......@@ -362,18 +356,28 @@ static int fsl_spi_bufs(struct spi_device *spi, struct spi_transfer *t,
static void fsl_spi_do_one_msg(struct spi_message *m)
{
struct spi_device *spi = m->spi;
struct spi_transfer *t;
struct spi_transfer *t, *first;
unsigned int cs_change;
const int nsecs = 50;
int status;
cs_change = 1;
status = 0;
/* Don't allow changes if CS is active */
first = list_first_entry(&m->transfers, struct spi_transfer,
transfer_list);
list_for_each_entry(t, &m->transfers, transfer_list) {
if (t->bits_per_word || t->speed_hz) {
/* Don't allow changes if CS is active */
if ((first->bits_per_word != t->bits_per_word) ||
(first->speed_hz != t->speed_hz)) {
status = -EINVAL;
dev_err(&spi->dev,
"bits_per_word/speed_hz should be same for the same SPI transfer\n");
return;
}
}
cs_change = 1;
status = -EINVAL;
list_for_each_entry(t, &m->transfers, transfer_list) {
if (t->bits_per_word || t->speed_hz) {
if (cs_change)
status = fsl_spi_setup_transfer(spi, t);
if (status < 0)
......@@ -641,6 +645,10 @@ static struct spi_master * fsl_spi_probe(struct device *dev,
if (mpc8xxx_spi->type == TYPE_GRLIB)
fsl_spi_grlib_probe(dev);
master->bits_per_word_mask =
(SPI_BPW_RANGE_MASK(4, 16) | SPI_BPW_MASK(32)) &
SPI_BPW_RANGE_MASK(1, mpc8xxx_spi->max_bits_per_word);
if (mpc8xxx_spi->flags & SPI_QE_CPU_MODE)
mpc8xxx_spi->set_shifts = fsl_spi_qe_cpu_set_shifts;
......
drivers/spi/spi-gpio.c
View file @ 09c0998e
......@@ -19,7 +19,6 @@
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>
#include <linux/of.h>
......@@ -250,7 +249,7 @@ static int spi_gpio_setup(struct spi_device *spi)
/*
* ... otherwise, take it from spi->controller_data
*/
cs = (unsigned int) spi->controller_data;
cs = (unsigned int)(uintptr_t) spi->controller_data;
}
if (!spi->controller_state) {
......@@ -503,13 +502,12 @@ static int spi_gpio_remove(struct platform_device *pdev)
{
struct spi_gpio *spi_gpio;
struct spi_gpio_platform_data *pdata;
int status;
spi_gpio = platform_get_drvdata(pdev);
pdata = dev_get_platdata(&pdev->dev);
/* stop() unregisters child devices too */
status = spi_bitbang_stop(&spi_gpio->bitbang);
spi_bitbang_stop(&spi_gpio->bitbang);
if (SPI_MISO_GPIO != SPI_GPIO_NO_MISO)
gpio_free(SPI_MISO_GPIO);
......@@ -518,7 +516,7 @@ static int spi_gpio_remove(struct platform_device *pdev)
gpio_free(SPI_SCK_GPIO);
spi_master_put(spi_gpio->bitbang.master);
return status;
return 0;
}
MODULE_ALIAS("platform:" DRIVER_NAME);
......
drivers/spi/spi-imx.c
View file @ 09c0998e
......@@ -23,7 +23,6 @@
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/irq.h>
......@@ -741,7 +740,7 @@ static int spi_imx_transfer(struct spi_device *spi,
spi_imx->count = transfer->len;
spi_imx->txfifo = 0;
init_completion(&spi_imx->xfer_done);
reinit_completion(&spi_imx->xfer_done);
spi_imx_push(spi_imx);
......@@ -880,12 +879,12 @@ static int spi_imx_probe(struct platform_device *pdev)
spi_imx->irq = platform_get_irq(pdev, 0);
if (spi_imx->irq < 0) {
ret = -EINVAL;
ret = spi_imx->irq;
goto out_master_put;
}
ret = devm_request_irq(&pdev->dev, spi_imx->irq, spi_imx_isr, 0,
DRIVER_NAME, spi_imx);
dev_name(&pdev->dev), spi_imx);
if (ret) {
dev_err(&pdev->dev, "can't get irq%d: %d\n", spi_imx->irq, ret);
goto out_master_put;
......
drivers/spi/spi-mpc512x-psc.c
View file @ 09c0998e
......@@ -16,7 +16,6 @@
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/errno.h>
#include <linux/interrupt.h>
#include <linux/of_address.h>
......@@ -466,10 +465,8 @@ static void mpc512x_spi_cs_control(struct spi_device *spi, bool onoff)
gpio_set_value(spi->cs_gpio, onoff);
}
/* bus_num is used only for the case dev->platform_data == NULL */
static int mpc512x_psc_spi_do_probe(struct device *dev, u32 regaddr,
u32 size, unsigned int irq,
s16 bus_num)
u32 size, unsigned int irq)
{
struct fsl_spi_platform_data *pdata = dev_get_platdata(dev);
struct mpc512x_psc_spi *mps;
......@@ -488,7 +485,6 @@ static int mpc512x_psc_spi_do_probe(struct device *dev, u32 regaddr,
if (pdata == NULL) {
mps->cs_control = mpc512x_spi_cs_control;
master->bus_num = bus_num;
} else {
mps->cs_control = pdata->cs_control;
master->bus_num = pdata->bus_num;
......@@ -574,7 +570,6 @@ static int mpc512x_psc_spi_of_probe(struct platform_device *op)
{
const u32 *regaddr_p;
u64 regaddr64, size64;
s16 id = -1;
regaddr_p = of_get_address(op->dev.of_node, 0, &size64, NULL);
if (!regaddr_p) {
......@@ -583,16 +578,8 @@ static int mpc512x_psc_spi_of_probe(struct platform_device *op)
}
regaddr64 = of_translate_address(op->dev.of_node, regaddr_p);
/* get PSC id (0..11, used by port_config) */
id = of_alias_get_id(op->dev.of_node, "spi");
if (id < 0) {
dev_err(&op->dev, "no alias id for %s\n",
op->dev.of_node->full_name);
return id;
}
return mpc512x_psc_spi_do_probe(&op->dev, (u32) regaddr64, (u32) size64,
irq_of_parse_and_map(op->dev.of_node, 0), id);
irq_of_parse_and_map(op->dev.of_node, 0));
}
static int mpc512x_psc_spi_of_remove(struct platform_device *op)
......
drivers/spi/spi-mpc52xx-psc.c
View file @ 09c0998e
......@@ -12,7 +12,6 @@
*/
#include <linux/module.h>
#include <linux/init.h>
#include <linux/types.h>
#include <linux/errno.h>
#include <linux/interrupt.h>
......
drivers/spi/spi-mpc52xx.c
View file @ 09c0998e
......@@ -12,7 +12,6 @@
*/
#include <linux/module.h>
#include <linux/init.h>
#include <linux/errno.h>
#include <linux/of_platform.h>
#include <linux/interrupt.h>
......@@ -357,20 +356,6 @@ static void mpc52xx_spi_wq(struct work_struct *work)
* spi_master ops
*/
static int mpc52xx_spi_setup(struct spi_device *spi)
{
if (spi->bits_per_word % 8)
return -EINVAL;
if (spi->mode & ~(SPI_CPOL | SPI_CPHA | SPI_LSB_FIRST))
return -EINVAL;
if (spi->chip_select >= spi->master->num_chipselect)
return -EINVAL;
return 0;
}
static int mpc52xx_spi_transfer(struct spi_device *spi, struct spi_message *m)
{
struct mpc52xx_spi *ms = spi_master_get_devdata(spi->master);
......@@ -433,9 +418,9 @@ static int mpc52xx_spi_probe(struct platform_device *op)
goto err_alloc;
}
master->setup = mpc52xx_spi_setup;
master->transfer = mpc52xx_spi_transfer;
master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_LSB_FIRST;
master->bits_per_word_mask = SPI_BPW_MASK(8);
master->dev.of_node = op->dev.of_node;
platform_set_drvdata(op, master);
......
drivers/spi/spi-mxs.c
View file @ 09c0998e
......@@ -29,7 +29,6 @@
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/ioport.h>
#include <linux/of.h>
#include <linux/of_device.h>
......@@ -371,7 +370,7 @@ static int mxs_spi_transfer_one(struct spi_master *master,
{
struct mxs_spi *spi = spi_master_get_devdata(master);
struct mxs_ssp *ssp = &spi->ssp;
struct spi_transfer *t, *tmp_t;
struct spi_transfer *t;
unsigned int flag;
int status = 0;
......@@ -381,7 +380,7 @@ static int mxs_spi_transfer_one(struct spi_master *master,
writel(mxs_spi_cs_to_reg(m->spi->chip_select),
ssp->base + HW_SSP_CTRL0 + STMP_OFFSET_REG_SET);
list_for_each_entry_safe(t, tmp_t, &m->transfers, transfer_list) {
list_for_each_entry(t, &m->transfers, transfer_list) {
status = mxs_spi_setup_transfer(m->spi, t);
if (status)
......@@ -473,7 +472,7 @@ static int mxs_spi_probe(struct platform_device *pdev)
iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
irq_err = platform_get_irq(pdev, 0);
if (irq_err < 0)
return -EINVAL;
return irq_err;
base = devm_ioremap_resource(&pdev->dev, iores);
if (IS_ERR(base))
......
drivers/spi/spi-nuc900.c
View file @ 09c0998e
......@@ -9,7 +9,6 @@
*/
#include <linux/module.h>
#include <linux/init.h>
#include <linux/spinlock.h>
#include <linux/workqueue.h>
#include <linux/interrupt.h>
......@@ -38,7 +37,9 @@
/* usi register bit */
#define ENINT (0x01 << 17)
#define ENFLG (0x01 << 16)
#define SLEEP (0x0f << 12)
#define TXNUM (0x03 << 8)
#define TXBITLEN (0x1f << 3)
#define TXNEG (0x01 << 2)
#define RXNEG (0x01 << 1)
#define LSB (0x01 << 10)
......@@ -58,11 +59,8 @@ struct nuc900_spi {
unsigned char *rx;
struct clk *clk;
struct spi_master *master;
struct spi_device *curdev;
struct device *dev;
struct nuc900_spi_info *pdata;
spinlock_t lock;
struct resource *res;
};
static inline struct nuc900_spi *to_hw(struct spi_device *sdev)
......@@ -119,19 +117,16 @@ static void nuc900_spi_chipsel(struct spi_device *spi, int value)
}
}
static void nuc900_spi_setup_txnum(struct nuc900_spi *hw,
unsigned int txnum)
static void nuc900_spi_setup_txnum(struct nuc900_spi *hw, unsigned int txnum)
{
unsigned int val;
unsigned long flags;
spin_lock_irqsave(&hw->lock, flags);
val = __raw_readl(hw->regs + USI_CNT);
val = __raw_readl(hw->regs + USI_CNT) & ~TXNUM;
if (!txnum)
val &= ~TXNUM;
else
if (txnum)
val |= txnum << 0x08;
__raw_writel(val, hw->regs + USI_CNT);
......@@ -148,7 +143,7 @@ static void nuc900_spi_setup_txbitlen(struct nuc900_spi *hw,
spin_lock_irqsave(&hw->lock, flags);
val = __raw_readl(hw->regs + USI_CNT);
val = __raw_readl(hw->regs + USI_CNT) & ~TXBITLEN;
val |= (txbitlen << 0x03);
......@@ -287,12 +282,11 @@ static void nuc900_set_sleep(struct nuc900_spi *hw, unsigned int sleep)
spin_lock_irqsave(&hw->lock, flags);
val = __raw_readl(hw->regs + USI_CNT);
val = __raw_readl(hw->regs + USI_CNT) & ~SLEEP;
if (sleep)
val |= (sleep << 12);
else
val &= ~(0x0f << 12);
__raw_writel(val, hw->regs + USI_CNT);
spin_unlock_irqrestore(&hw->lock, flags);
......@@ -338,6 +332,7 @@ static int nuc900_spi_probe(struct platform_device *pdev)
{
struct nuc900_spi *hw;
struct spi_master *master;
struct resource *res;
int err = 0;
master = spi_alloc_master(&pdev->dev, sizeof(struct nuc900_spi));
......@@ -349,7 +344,6 @@ static int nuc900_spi_probe(struct platform_device *pdev)
hw = spi_master_get_devdata(master);
hw->master = master;
hw->pdata = dev_get_platdata(&pdev->dev);
hw->dev = &pdev->dev;
if (hw->pdata == NULL) {
dev_err(&pdev->dev, "No platform data supplied\n");
......@@ -369,8 +363,8 @@ static int nuc900_spi_probe(struct platform_device *pdev)
hw->bitbang.chipselect = nuc900_spi_chipsel;
hw->bitbang.txrx_bufs = nuc900_spi_txrx;
hw->res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
hw->regs = devm_ioremap_resource(&pdev->dev, hw->res);
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
hw->regs = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(hw->regs)) {
err = PTR_ERR(hw->regs);
goto err_pdata;
......
drivers/spi/spi-oc-tiny.c
View file @ 09c0998e
......@@ -15,7 +15,6 @@
* published by the Free Software Foundation.
*/
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/errno.h>
#include <linux/module.h>
......@@ -267,8 +266,6 @@ static int tiny_spi_probe(struct platform_device *pdev)
/* setup the state for the bitbang driver */
hw->bitbang.master = master;
if (!hw->bitbang.master)
return err;
hw->bitbang.setup_transfer = tiny_spi_setup_transfer;
hw->bitbang.chipselect = tiny_spi_chipselect;
hw->bitbang.txrx_bufs = tiny_spi_txrx_bufs;
......
drivers/spi/spi-octeon.c
View file @ 09c0998e
......@@ -11,7 +11,6 @@
#include <linux/spi/spi.h>
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/init.h>
#include <linux/io.h>
#include <linux/of.h>
......@@ -33,13 +32,6 @@ struct octeon_spi {
u64 cs_enax;
};
struct octeon_spi_setup {
u32 max_speed_hz;
u8 chip_select;
u8 mode;
u8 bits_per_word;
};
static void octeon_spi_wait_ready(struct octeon_spi *p)
{
union cvmx_mpi_sts mpi_sts;
......@@ -57,6 +49,7 @@ static int octeon_spi_do_transfer(struct octeon_spi *p,
struct spi_transfer *xfer,
bool last_xfer)
{
struct spi_device *spi = msg->spi;
union cvmx_mpi_cfg mpi_cfg;
union cvmx_mpi_tx mpi_tx;
unsigned int clkdiv;
......@@ -68,18 +61,11 @@ static int octeon_spi_do_transfer(struct octeon_spi *p,
int len;
int i;
struct octeon_spi_setup *msg_setup = spi_get_ctldata(msg->spi);
speed_hz = msg_setup->max_speed_hz;
mode = msg_setup->mode;
mode = spi->mode;
cpha = mode & SPI_CPHA;
cpol = mode & SPI_CPOL;
if (xfer->speed_hz)
speed_hz = xfer->speed_hz;
if (speed_hz > OCTEON_SPI_MAX_CLOCK_HZ)
speed_hz = OCTEON_SPI_MAX_CLOCK_HZ;
speed_hz = xfer->speed_hz ? : spi->max_speed_hz;
clkdiv = octeon_get_io_clock_rate() / (2 * speed_hz);
......@@ -93,8 +79,8 @@ static int octeon_spi_do_transfer(struct octeon_spi *p,
mpi_cfg.s.cslate = cpha ? 1 : 0;
mpi_cfg.s.enable = 1;
if (msg_setup->chip_select < 4)
p->cs_enax |= 1ull << (12 + msg_setup->chip_select);
if (spi->chip_select < 4)
p->cs_enax |= 1ull << (12 + spi->chip_select);
mpi_cfg.u64 |= p->cs_enax;
if (mpi_cfg.u64 != p->last_cfg) {
......@@ -114,7 +100,7 @@ static int octeon_spi_do_transfer(struct octeon_spi *p,
cvmx_write_csr(p->register_base + OCTEON_SPI_DAT0 + (8 * i), d);
}
mpi_tx.u64 = 0;
mpi_tx.s.csid = msg_setup->chip_select;
mpi_tx.s.csid = spi->chip_select;
mpi_tx.s.leavecs = 1;
mpi_tx.s.txnum = tx_buf ? OCTEON_SPI_MAX_BYTES : 0;
mpi_tx.s.totnum = OCTEON_SPI_MAX_BYTES;
......@@ -139,7 +125,7 @@ static int octeon_spi_do_transfer(struct octeon_spi *p,
}
mpi_tx.u64 = 0;
mpi_tx.s.csid = msg_setup->chip_select;
mpi_tx.s.csid = spi->chip_select;
if (last_xfer)
mpi_tx.s.leavecs = xfer->cs_change;
else
......@@ -169,17 +155,9 @@ static int octeon_spi_transfer_one_message(struct spi_master *master,
int status = 0;
struct spi_transfer *xfer;
/*
* We better have set the configuration via a call to .setup
* before we get here.
*/
if (spi_get_ctldata(msg->spi) == NULL) {
status = -EINVAL;
goto err;
}
list_for_each_entry(xfer, &msg->transfers, transfer_list) {
bool last_xfer = &xfer->transfer_list == msg->transfers.prev;
bool last_xfer = list_is_last(&xfer->transfer_list,
&msg->transfers);
int r = octeon_spi_do_transfer(p, msg, xfer, last_xfer);
if (r < 0) {
status = r;
......@@ -194,41 +172,6 @@ static int octeon_spi_transfer_one_message(struct spi_master *master,
return status;
}
static struct octeon_spi_setup *octeon_spi_new_setup(struct spi_device *spi)
{
struct octeon_spi_setup *setup = kzalloc(sizeof(*setup), GFP_KERNEL);
if (!setup)
return NULL;
setup->max_speed_hz = spi->max_speed_hz;
setup->chip_select = spi->chip_select;
setup->mode = spi->mode;
setup->bits_per_word = spi->bits_per_word;
return setup;
}
static int octeon_spi_setup(struct spi_device *spi)
{
struct octeon_spi_setup *new_setup;
struct octeon_spi_setup *old_setup = spi_get_ctldata(spi);
new_setup = octeon_spi_new_setup(spi);
if (!new_setup)
return -ENOMEM;
spi_set_ctldata(spi, new_setup);
kfree(old_setup);
return 0;
}
static void octeon_spi_cleanup(struct spi_device *spi)
{
struct octeon_spi_setup *old_setup = spi_get_ctldata(spi);
spi_set_ctldata(spi, NULL);
kfree(old_setup);
}
static int octeon_spi_probe(struct platform_device *pdev)
{
struct resource *res_mem;
......@@ -257,8 +200,6 @@ static int octeon_spi_probe(struct platform_device *pdev)
p->register_base = (u64)devm_ioremap(&pdev->dev, res_mem->start,
resource_size(res_mem));
/* Dynamic bus numbering */
master->bus_num = -1;
master->num_chipselect = 4;
master->mode_bits = SPI_CPHA |
SPI_CPOL |
......@@ -266,10 +207,9 @@ static int octeon_spi_probe(struct platform_device *pdev)
SPI_LSB_FIRST |
SPI_3WIRE;
master->setup = octeon_spi_setup;
master->cleanup = octeon_spi_cleanup;
master->transfer_one_message = octeon_spi_transfer_one_message;
master->bits_per_word_mask = SPI_BPW_MASK(8);
master->max_speed_hz = OCTEON_SPI_MAX_CLOCK_HZ;
master->dev.of_node = pdev->dev.of_node;
err = devm_spi_register_master(&pdev->dev, master);
......
drivers/spi/spi-omap-100k.c
View file @ 09c0998e
......@@ -83,15 +83,11 @@
#define SPI_SHUTDOWN 1
struct omap1_spi100k {
struct spi_master *master;
struct clk *ick;
struct clk *fck;
/* Virtual base address of the controller */
void __iomem *base;
/* State of the SPI */
unsigned int state;
};
struct omap1_spi100k_cs {
......@@ -99,13 +95,6 @@ struct omap1_spi100k_cs {
int word_len;
};
#define MOD_REG_BIT(val, mask, set) do { \
if (set) \
val |= mask; \
else \
val &= ~mask; \
} while (0)
static void spi100k_enable_clock(struct spi_master *master)
{
unsigned int val;
......@@ -139,7 +128,7 @@ static void spi100k_write_data(struct spi_master *master, int len, int data)
}
spi100k_enable_clock(master);
writew( data , spi100k->base + SPI_TX_MSB);
writew(data , spi100k->base + SPI_TX_MSB);
writew(SPI_CTRL_SEN(0) |
SPI_CTRL_WORD_SIZE(len) |
......@@ -147,7 +136,8 @@ static void spi100k_write_data(struct spi_master *master, int len, int data)
spi100k->base + SPI_CTRL);
/* Wait for bit ack send change */
while((readw(spi100k->base + SPI_STATUS) & SPI_STATUS_WE) != SPI_STATUS_WE);
while ((readw(spi100k->base + SPI_STATUS) & SPI_STATUS_WE) != SPI_STATUS_WE)
;
udelay(1000);
spi100k_disable_clock(master);
......@@ -155,7 +145,7 @@ static void spi100k_write_data(struct spi_master *master, int len, int data)
static int spi100k_read_data(struct spi_master *master, int len)
{
int dataH,dataL;
int dataH, dataL;
struct omap1_spi100k *spi100k = spi_master_get_devdata(master);
/* Always do at least 16 bits */
......@@ -168,7 +158,8 @@ static int spi100k_read_data(struct spi_master *master, int len)
SPI_CTRL_RD,
spi100k->base + SPI_CTRL);
while((readw(spi100k->base + SPI_STATUS) & SPI_STATUS_RD) != SPI_STATUS_RD);
while ((readw(spi100k->base + SPI_STATUS) & SPI_STATUS_RD) != SPI_STATUS_RD)
;
udelay(1000);
dataL = readw(spi100k->base + SPI_RX_LSB);
......@@ -204,12 +195,10 @@ static void omap1_spi100k_force_cs(struct omap1_spi100k *spi100k, int enable)
static unsigned
omap1_spi100k_txrx_pio(struct spi_device *spi, struct spi_transfer *xfer)
{
struct omap1_spi100k *spi100k;
struct omap1_spi100k_cs *cs = spi->controller_state;
unsigned int count, c;
int word_len;
spi100k = spi_master_get_devdata(spi->master);
count = xfer->len;
c = count;
word_len = cs->word_len;
......@@ -221,12 +210,12 @@ omap1_spi100k_txrx_pio(struct spi_device *spi, struct spi_transfer *xfer)
rx = xfer->rx_buf;
tx = xfer->tx_buf;
do {
c-=1;
c -= 1;
if (xfer->tx_buf != NULL)
spi100k_write_data(spi->master, word_len, *tx++);
if (xfer->rx_buf != NULL)
*rx++ = spi100k_read_data(spi->master, word_len);
} while(c);
} while (c);
} else if (word_len <= 16) {
u16 *rx;
const u16 *tx;
......@@ -234,12 +223,12 @@ omap1_spi100k_txrx_pio(struct spi_device *spi, struct spi_transfer *xfer)
rx = xfer->rx_buf;
tx = xfer->tx_buf;
do {
c-=2;
c -= 2;
if (xfer->tx_buf != NULL)
spi100k_write_data(spi->master,word_len, *tx++);
spi100k_write_data(spi->master, word_len, *tx++);
if (xfer->rx_buf != NULL)
*rx++ = spi100k_read_data(spi->master,word_len);
} while(c);
*rx++ = spi100k_read_data(spi->master, word_len);
} while (c);
} else if (word_len <= 32) {
u32 *rx;
const u32 *tx;
......@@ -247,12 +236,12 @@ omap1_spi100k_txrx_pio(struct spi_device *spi, struct spi_transfer *xfer)
rx = xfer->rx_buf;
tx = xfer->tx_buf;
do {
c-=4;
c -= 4;
if (xfer->tx_buf != NULL)
spi100k_write_data(spi->master,word_len, *tx);
spi100k_write_data(spi->master, word_len, *tx);
if (xfer->rx_buf != NULL)
*rx = spi100k_read_data(spi->master,word_len);
} while(c);
*rx = spi100k_read_data(spi->master, word_len);
} while (c);
}
return count - c;
}
......@@ -294,7 +283,7 @@ static int omap1_spi100k_setup(struct spi_device *spi)
spi100k = spi_master_get_devdata(spi->master);
if (!cs) {
cs = kzalloc(sizeof *cs, GFP_KERNEL);
cs = devm_kzalloc(&spi->dev, sizeof(*cs), GFP_KERNEL);
if (!cs)
return -ENOMEM;
cs->base = spi100k->base + spi->chip_select * 0x14;
......@@ -411,14 +400,14 @@ static int omap1_spi100k_probe(struct platform_device *pdev)
if (!pdev->id)
return -EINVAL;
master = spi_alloc_master(&pdev->dev, sizeof *spi100k);
master = spi_alloc_master(&pdev->dev, sizeof(*spi100k));
if (master == NULL) {
dev_dbg(&pdev->dev, "master allocation failed\n");
return -ENOMEM;
}
if (pdev->id != -1)
master->bus_num = pdev->id;
master->bus_num = pdev->id;
master->setup = omap1_spi100k_setup;
master->transfer_one_message = omap1_spi100k_transfer_one_message;
......@@ -434,7 +423,6 @@ static int omap1_spi100k_probe(struct platform_device *pdev)
platform_set_drvdata(pdev, master);
spi100k = spi_master_get_devdata(master);
spi100k->master = master;
/*
* The memory region base address is taken as the platform_data.
......@@ -461,8 +449,6 @@ static int omap1_spi100k_probe(struct platform_device *pdev)
if (status < 0)
goto err;
spi100k->state = SPI_RUNNING;
return status;
err:
......
drivers/spi/spi-omap-uwire.c
View file @ 09c0998e
......@@ -99,7 +99,6 @@ struct uwire_spi {
};
struct uwire_state {
unsigned bits_per_word;
unsigned div1_idx;
};
......@@ -210,9 +209,8 @@ static void uwire_chipselect(struct spi_device *spi, int value)
static int uwire_txrx(struct spi_device *spi, struct spi_transfer *t)
{
struct uwire_state *ust = spi->controller_state;
unsigned len = t->len;
unsigned bits = ust->bits_per_word;
unsigned bits = t->bits_per_word ? : spi->bits_per_word;
unsigned bytes;
u16 val, w;
int status = 0;
......@@ -220,10 +218,6 @@ static int uwire_txrx(struct spi_device *spi, struct spi_transfer *t)
if (!t->tx_buf && !t->rx_buf)
return 0;
/* Microwire doesn't read and write concurrently */
if (t->tx_buf && t->rx_buf)
return -EPERM;
w = spi->chip_select << 10;
w |= CS_CMD;
......@@ -322,7 +316,6 @@ static int uwire_setup_transfer(struct spi_device *spi, struct spi_transfer *t)
struct uwire_state *ust = spi->controller_state;
struct uwire_spi *uwire;
unsigned flags = 0;
unsigned bits;
unsigned hz;
unsigned long rate;
int div1_idx;
......@@ -332,23 +325,6 @@ static int uwire_setup_transfer(struct spi_device *spi, struct spi_transfer *t)
uwire = spi_master_get_devdata(spi->master);
if (spi->chip_select > 3) {
pr_debug("%s: cs%d?\n", dev_name(&spi->dev), spi->chip_select);
status = -ENODEV;
goto done;
}
bits = spi->bits_per_word;
if (t != NULL && t->bits_per_word)
bits = t->bits_per_word;
if (bits > 16) {
pr_debug("%s: wordsize %d?\n", dev_name(&spi->dev), bits);
status = -ENODEV;
goto done;
}
ust->bits_per_word = bits;
/* mode 0..3, clock inverted separately;
* standard nCS signaling;
* don't treat DI=high as "not ready"
......@@ -502,6 +478,7 @@ static int uwire_probe(struct platform_device *pdev)
status = PTR_ERR(uwire->ck);
dev_dbg(&pdev->dev, "no functional clock?\n");
spi_master_put(master);
iounmap(uwire_base);
return status;
}
clk_enable(uwire->ck);
......@@ -515,7 +492,7 @@ static int uwire_probe(struct platform_device *pdev)
/* the spi->mode bits understood by this driver: */
master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
master->bits_per_word_mask = SPI_BPW_RANGE_MASK(1, 16);
master->flags = SPI_MASTER_HALF_DUPLEX;
master->bus_num = 2; /* "official" */
......@@ -539,14 +516,13 @@ static int uwire_probe(struct platform_device *pdev)
static int uwire_remove(struct platform_device *pdev)
{
struct uwire_spi *uwire = platform_get_drvdata(pdev);
int status;
// FIXME remove all child devices, somewhere ...
status = spi_bitbang_stop(&uwire->bitbang);
spi_bitbang_stop(&uwire->bitbang);
uwire_off(uwire);
iounmap(uwire_base);
return status;
return 0;
}
/* work with hotplug and coldplug */
......
drivers/spi/spi-omap2-mcspi.c
View file @ 09c0998e
......@@ -22,7 +22,6 @@
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/module.h>
#include <linux/device.h>
......@@ -45,6 +44,7 @@
#include <linux/platform_data/spi-omap2-mcspi.h>
#define OMAP2_MCSPI_MAX_FREQ 48000000
#define OMAP2_MCSPI_MAX_DIVIDER 4096
#define OMAP2_MCSPI_MAX_FIFODEPTH 64
#define OMAP2_MCSPI_MAX_FIFOWCNT 0xFFFF
#define SPI_AUTOSUSPEND_TIMEOUT 2000
......@@ -89,6 +89,7 @@
#define OMAP2_MCSPI_CHCONF_FORCE BIT(20)
#define OMAP2_MCSPI_CHCONF_FFET BIT(27)
#define OMAP2_MCSPI_CHCONF_FFER BIT(28)
#define OMAP2_MCSPI_CHCONF_CLKG BIT(29)
#define OMAP2_MCSPI_CHSTAT_RXS BIT(0)
#define OMAP2_MCSPI_CHSTAT_TXS BIT(1)
......@@ -96,6 +97,7 @@
#define OMAP2_MCSPI_CHSTAT_TXFFE BIT(3)
#define OMAP2_MCSPI_CHCTRL_EN BIT(0)
#define OMAP2_MCSPI_CHCTRL_EXTCLK_MASK (0xff << 8)
#define OMAP2_MCSPI_WAKEUPENABLE_WKEN BIT(0)
......@@ -149,7 +151,7 @@ struct omap2_mcspi_cs {
int word_len;
struct list_head node;
/* Context save and restore shadow register */
u32 chconf0;
u32 chconf0, chctrl0;
};
static inline void mcspi_write_reg(struct spi_master *master,
......@@ -230,10 +232,16 @@ static void omap2_mcspi_set_dma_req(const struct spi_device *spi,
static void omap2_mcspi_set_enable(const struct spi_device *spi, int enable)
{
struct omap2_mcspi_cs *cs = spi->controller_state;
u32 l;
l = enable ? OMAP2_MCSPI_CHCTRL_EN : 0;
mcspi_write_cs_reg(spi, OMAP2_MCSPI_CHCTRL0, l);
l = cs->chctrl0;
if (enable)
l |= OMAP2_MCSPI_CHCTRL_EN;
else
l &= ~OMAP2_MCSPI_CHCTRL_EN;
cs->chctrl0 = l;
mcspi_write_cs_reg(spi, OMAP2_MCSPI_CHCTRL0, cs->chctrl0);
/* Flash post-writes */
mcspi_read_cs_reg(spi, OMAP2_MCSPI_CHCTRL0);
}
......@@ -840,7 +848,7 @@ static int omap2_mcspi_setup_transfer(struct spi_device *spi,
struct omap2_mcspi_cs *cs = spi->controller_state;
struct omap2_mcspi *mcspi;
struct spi_master *spi_cntrl;
u32 l = 0, div = 0;
u32 l = 0, clkd = 0, div, extclk = 0, clkg = 0;
u8 word_len = spi->bits_per_word;
u32 speed_hz = spi->max_speed_hz;
......@@ -856,7 +864,17 @@ static int omap2_mcspi_setup_transfer(struct spi_device *spi,
speed_hz = t->speed_hz;
speed_hz = min_t(u32, speed_hz, OMAP2_MCSPI_MAX_FREQ);
div = omap2_mcspi_calc_divisor(speed_hz);
if (speed_hz < (OMAP2_MCSPI_MAX_FREQ / OMAP2_MCSPI_MAX_DIVIDER)) {
clkd = omap2_mcspi_calc_divisor(speed_hz);
speed_hz = OMAP2_MCSPI_MAX_FREQ >> clkd;
clkg = 0;
} else {
div = (OMAP2_MCSPI_MAX_FREQ + speed_hz - 1) / speed_hz;
speed_hz = OMAP2_MCSPI_MAX_FREQ / div;
clkd = (div - 1) & 0xf;
extclk = (div - 1) >> 4;
clkg = OMAP2_MCSPI_CHCONF_CLKG;
}
l = mcspi_cached_chconf0(spi);
......@@ -885,7 +903,16 @@ static int omap2_mcspi_setup_transfer(struct spi_device *spi,
/* set clock divisor */
l &= ~OMAP2_MCSPI_CHCONF_CLKD_MASK;
l |= div << 2;
l |= clkd << 2;
/* set clock granularity */
l &= ~OMAP2_MCSPI_CHCONF_CLKG;
l |= clkg;
if (clkg) {
cs->chctrl0 &= ~OMAP2_MCSPI_CHCTRL_EXTCLK_MASK;
cs->chctrl0 |= extclk << 8;
mcspi_write_cs_reg(spi, OMAP2_MCSPI_CHCTRL0, cs->chctrl0);
}
/* set SPI mode 0..3 */
if (spi->mode & SPI_CPOL)
......@@ -900,7 +927,7 @@ static int omap2_mcspi_setup_transfer(struct spi_device *spi,
mcspi_write_chconf0(spi, l);
dev_dbg(&spi->dev, "setup: speed %d, sample %s edge, clk %s\n",
OMAP2_MCSPI_MAX_FREQ >> div,
speed_hz,
(spi->mode & SPI_CPHA) ? "trailing" : "leading",
(spi->mode & SPI_CPOL) ? "inverted" : "normal");
......@@ -972,6 +999,7 @@ static int omap2_mcspi_setup(struct spi_device *spi)
cs->base = mcspi->base + spi->chip_select * 0x14;
cs->phys = mcspi->phys + spi->chip_select * 0x14;
cs->chconf0 = 0;
cs->chctrl0 = 0;
spi->controller_state = cs;
/* Link this to context save list */
list_add_tail(&cs->node, &ctx->cs);
......@@ -1057,12 +1085,15 @@ static void omap2_mcspi_work(struct omap2_mcspi *mcspi, struct spi_message *m)
status = -EINVAL;
break;
}
if (par_override || t->speed_hz || t->bits_per_word) {
if (par_override ||
(t->speed_hz != spi->max_speed_hz) ||
(t->bits_per_word != spi->bits_per_word)) {
par_override = 1;
status = omap2_mcspi_setup_transfer(spi, t);
if (status < 0)
break;
if (!t->speed_hz && !t->bits_per_word)
if (t->speed_hz == spi->max_speed_hz &&
t->bits_per_word == spi->bits_per_word)
par_override = 0;
}
if (cd && cd->cs_per_word) {
......@@ -1176,16 +1207,12 @@ static int omap2_mcspi_transfer_one_message(struct spi_master *master,
m->actual_length = 0;
m->status = 0;
/* reject invalid messages and transfers */
if (list_empty(&m->transfers))
return -EINVAL;
list_for_each_entry(t, &m->transfers, transfer_list) {
const void *tx_buf = t->tx_buf;
void *rx_buf = t->rx_buf;
unsigned len = t->len;
if (t->speed_hz > OMAP2_MCSPI_MAX_FREQ
|| (len && !(rx_buf || tx_buf))) {
if ((len && !(rx_buf || tx_buf))) {
dev_dbg(mcspi->dev, "transfer: %d Hz, %d %s%s, %d bpw\n",
t->speed_hz,
len,
......@@ -1194,12 +1221,6 @@ static int omap2_mcspi_transfer_one_message(struct spi_master *master,
t->bits_per_word);
return -EINVAL;
}
if (t->speed_hz && t->speed_hz < (OMAP2_MCSPI_MAX_FREQ >> 15)) {
dev_dbg(mcspi->dev, "speed_hz %d below minimum %d Hz\n",
t->speed_hz,
OMAP2_MCSPI_MAX_FREQ >> 15);
return -EINVAL;
}
if (m->is_dma_mapped || len < DMA_MIN_BYTES)
continue;
......@@ -1311,6 +1332,8 @@ static int omap2_mcspi_probe(struct platform_device *pdev)
master->transfer_one_message = omap2_mcspi_transfer_one_message;
master->cleanup = omap2_mcspi_cleanup;
master->dev.of_node = node;
master->max_speed_hz = OMAP2_MCSPI_MAX_FREQ;
master->min_speed_hz = OMAP2_MCSPI_MAX_FREQ >> 15;
platform_set_drvdata(pdev, master);
......
drivers/spi/spi-orion.c
View file @ 09c0998e
......@@ -9,7 +9,6 @@
* published by the Free Software Foundation.
*/
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/delay.h>
#include <linux/platform_device.h>
......@@ -43,8 +42,6 @@
struct orion_spi {
struct spi_master *master;
void __iomem *base;
unsigned int max_speed;
unsigned int min_speed;
struct clk *clk;
};
......@@ -75,23 +72,6 @@ orion_spi_clrbits(struct orion_spi *orion_spi, u32 reg, u32 mask)
writel(val, reg_addr);
}
static int orion_spi_set_transfer_size(struct orion_spi *orion_spi, int size)
{
if (size == 16) {
orion_spi_setbits(orion_spi, ORION_SPI_IF_CONFIG_REG,
ORION_SPI_IF_8_16_BIT_MODE);
} else if (size == 8) {
orion_spi_clrbits(orion_spi, ORION_SPI_IF_CONFIG_REG,
ORION_SPI_IF_8_16_BIT_MODE);
} else {
pr_debug("Bad bits per word value %d (only 8 or 16 are allowed).\n",
size);
return -EINVAL;
}
return 0;
}
static int orion_spi_baudrate_set(struct spi_device *spi, unsigned int speed)
{
u32 tclk_hz;
......@@ -170,7 +150,14 @@ orion_spi_setup_transfer(struct spi_device *spi, struct spi_transfer *t)
if (rc)
return rc;
return orion_spi_set_transfer_size(orion_spi, bits_per_word);
if (bits_per_word == 16)
orion_spi_setbits(orion_spi, ORION_SPI_IF_CONFIG_REG,
ORION_SPI_IF_8_16_BIT_MODE);
else
orion_spi_clrbits(orion_spi, ORION_SPI_IF_CONFIG_REG,
ORION_SPI_IF_8_16_BIT_MODE);
return 0;
}
static void orion_spi_set_cs(struct orion_spi *orion_spi, int enable)
......@@ -260,11 +247,9 @@ orion_spi_write_read_16bit(struct spi_device *spi,
static unsigned int
orion_spi_write_read(struct spi_device *spi, struct spi_transfer *xfer)
{
struct orion_spi *orion_spi;
unsigned int count;
int word_len;
orion_spi = spi_master_get_devdata(spi->master);
word_len = spi->bits_per_word;
count = xfer->len;
......@@ -310,27 +295,6 @@ static int orion_spi_transfer_one_message(struct spi_master *master,
goto msg_done;
list_for_each_entry(t, &m->transfers, transfer_list) {
/* make sure buffer length is even when working in 16
* bit mode*/
if ((t->bits_per_word == 16) && (t->len & 1)) {
dev_err(&spi->dev,
"message rejected : "
"odd data length %d while in 16 bit mode\n",
t->len);
status = -EIO;
goto msg_done;
}
if (t->speed_hz && t->speed_hz < orion_spi->min_speed) {
dev_err(&spi->dev,
"message rejected : "
"device min speed (%d Hz) exceeds "
"required transfer speed (%d Hz)\n",
orion_spi->min_speed, t->speed_hz);
status = -EIO;
goto msg_done;
}
if (par_override || t->speed_hz || t->bits_per_word) {
par_override = 1;
status = orion_spi_setup_transfer(spi, t);
......@@ -375,28 +339,6 @@ static int orion_spi_reset(struct orion_spi *orion_spi)
return 0;
}
static int orion_spi_setup(struct spi_device *spi)
{
struct orion_spi *orion_spi;
orion_spi = spi_master_get_devdata(spi->master);
if ((spi->max_speed_hz == 0)
|| (spi->max_speed_hz > orion_spi->max_speed))
spi->max_speed_hz = orion_spi->max_speed;
if (spi->max_speed_hz < orion_spi->min_speed) {
dev_err(&spi->dev, "setup: requested speed too low %d Hz\n",
spi->max_speed_hz);
return -EINVAL;
}
/*
* baudrate & width will be set orion_spi_setup_transfer
*/
return 0;
}
static int orion_spi_probe(struct platform_device *pdev)
{
struct spi_master *master;
......@@ -425,9 +367,9 @@ static int orion_spi_probe(struct platform_device *pdev)
/* we support only mode 0, and no options */
master->mode_bits = SPI_CPHA | SPI_CPOL;
master->setup = orion_spi_setup;
master->transfer_one_message = orion_spi_transfer_one_message;
master->num_chipselect = ORION_NUM_CHIPSELECTS;
master->bits_per_word_mask = SPI_BPW_MASK(8) | SPI_BPW_MASK(16);
platform_set_drvdata(pdev, master);
......@@ -443,8 +385,8 @@ static int orion_spi_probe(struct platform_device *pdev)
clk_prepare(spi->clk);
clk_enable(spi->clk);
tclk_hz = clk_get_rate(spi->clk);
spi->max_speed = DIV_ROUND_UP(tclk_hz, 4);
spi->min_speed = DIV_ROUND_UP(tclk_hz, 30);
master->max_speed_hz = DIV_ROUND_UP(tclk_hz, 4);
master->min_speed_hz = DIV_ROUND_UP(tclk_hz, 30);
r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
spi->base = devm_ioremap_resource(&pdev->dev, r);
......
drivers/spi/spi-pl022.c
View file @ 09c0998e
......@@ -459,9 +459,8 @@ static void giveback(struct pl022 *pl022)
struct spi_transfer *last_transfer;
pl022->next_msg_cs_active = false;
last_transfer = list_entry(pl022->cur_msg->transfers.prev,
struct spi_transfer,
transfer_list);
last_transfer = list_last_entry(&pl022->cur_msg->transfers,
struct spi_transfer, transfer_list);
/* Delay if requested before any change in chip select */
if (last_transfer->delay_usecs)
......@@ -2109,8 +2108,6 @@ static int pl022_probe(struct amba_device *adev, const struct amba_id *id)
pl022->chipselects = devm_kzalloc(dev, num_cs * sizeof(int),
GFP_KERNEL);
pinctrl_pm_select_default_state(dev);
/*
* Bus Number Which has been Assigned to this SSP controller
* on this board
......@@ -2183,13 +2180,7 @@ static int pl022_probe(struct amba_device *adev, const struct amba_id *id)
goto err_no_clk;
}
status = clk_prepare(pl022->clk);
if (status) {
dev_err(&adev->dev, "could not prepare SSP/SPI bus clock\n");
goto err_clk_prep;
}
status = clk_enable(pl022->clk);
status = clk_prepare_enable(pl022->clk);
if (status) {
dev_err(&adev->dev, "could not enable SSP/SPI bus clock\n");
goto err_no_clk_en;
......@@ -2250,10 +2241,8 @@ static int pl022_probe(struct amba_device *adev, const struct amba_id *id)
if (platform_info->enable_dma)
pl022_dma_remove(pl022);
err_no_irq:
clk_disable(pl022->clk);
clk_disable_unprepare(pl022->clk);
err_no_clk_en:
clk_unprepare(pl022->clk);
err_clk_prep:
err_no_clk:
err_no_ioremap:
amba_release_regions(adev);
......@@ -2281,42 +2270,13 @@ pl022_remove(struct amba_device *adev)
if (pl022->master_info->enable_dma)
pl022_dma_remove(pl022);
clk_disable(pl022->clk);
clk_unprepare(pl022->clk);
clk_disable_unprepare(pl022->clk);
amba_release_regions(adev);
tasklet_disable(&pl022->pump_transfers);
return 0;
}
#if defined(CONFIG_SUSPEND) || defined(CONFIG_PM_RUNTIME)
/*
* These two functions are used from both suspend/resume and
* the runtime counterparts to handle external resources like
* clocks, pins and regulators when going to sleep.
*/
static void pl022_suspend_resources(struct pl022 *pl022, bool runtime)
{
clk_disable(pl022->clk);
if (runtime)
pinctrl_pm_select_idle_state(&pl022->adev->dev);
else
pinctrl_pm_select_sleep_state(&pl022->adev->dev);
}
static void pl022_resume_resources(struct pl022 *pl022, bool runtime)
{
/* First go to the default state */
pinctrl_pm_select_default_state(&pl022->adev->dev);
if (!runtime)
/* Then let's idle the pins until the next transfer happens */
pinctrl_pm_select_idle_state(&pl022->adev->dev);
clk_enable(pl022->clk);
}
#endif
#ifdef CONFIG_SUSPEND
#ifdef CONFIG_PM_SLEEP
static int pl022_suspend(struct device *dev)
{
struct pl022 *pl022 = dev_get_drvdata(dev);
......@@ -2328,8 +2288,13 @@ static int pl022_suspend(struct device *dev)
return ret;
}
pm_runtime_get_sync(dev);
pl022_suspend_resources(pl022, false);
ret = pm_runtime_force_suspend(dev);
if (ret) {
spi_master_resume(pl022->master);
return ret;
}
pinctrl_pm_select_sleep_state(dev);
dev_dbg(dev, "suspended\n");
return 0;
......@@ -2340,8 +2305,9 @@ static int pl022_resume(struct device *dev)
struct pl022 *pl022 = dev_get_drvdata(dev);
int ret;
pl022_resume_resources(pl022, false);
pm_runtime_put(dev);
ret = pm_runtime_force_resume(dev);
if (ret)
dev_err(dev, "problem resuming\n");
/* Start the queue running */
ret = spi_master_resume(pl022->master);
......@@ -2352,14 +2318,16 @@ static int pl022_resume(struct device *dev)
return ret;
}
#endif /* CONFIG_PM */
#endif
#ifdef CONFIG_PM_RUNTIME
#ifdef CONFIG_PM
static int pl022_runtime_suspend(struct device *dev)
{
struct pl022 *pl022 = dev_get_drvdata(dev);
pl022_suspend_resources(pl022, true);
clk_disable_unprepare(pl022->clk);
pinctrl_pm_select_idle_state(dev);
return 0;
}
......@@ -2367,14 +2335,16 @@ static int pl022_runtime_resume(struct device *dev)
{
struct pl022 *pl022 = dev_get_drvdata(dev);
pl022_resume_resources(pl022, true);
pinctrl_pm_select_default_state(dev);
clk_prepare_enable(pl022->clk);
return 0;
}
#endif
static const struct dev_pm_ops pl022_dev_pm_ops = {
SET_SYSTEM_SLEEP_PM_OPS(pl022_suspend, pl022_resume)
SET_RUNTIME_PM_OPS(pl022_runtime_suspend, pl022_runtime_resume, NULL)
SET_PM_RUNTIME_PM_OPS(pl022_runtime_suspend, pl022_runtime_resume, NULL)
};
static struct vendor_data vendor_arm = {
......
drivers/spi/spi-ppc4xx.c
View file @ 09c0998e
......@@ -24,7 +24,6 @@
*/
#include <linux/module.h>
#include <linux/init.h>
#include <linux/sched.h>
#include <linux/slab.h>
#include <linux/errno.h>
......
drivers/spi/spi-pxa2xx-dma.c
View file @ 09c0998e
......@@ -9,7 +9,6 @@
* published by the Free Software Foundation.
*/
#include <linux/init.h>
#include <linux/device.h>
#include <linux/dma-mapping.h>
#include <linux/dmaengine.h>
......
drivers/spi/spi-pxa2xx-pxadma.c
View file @ 09c0998e
......@@ -18,7 +18,6 @@
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/device.h>
#include <linux/dma-mapping.h>
......
drivers/spi/spi-pxa2xx.c
View file @ 09c0998e
......@@ -362,8 +362,7 @@ static void giveback(struct driver_data *drv_data)
drv_data->cur_msg = NULL;
drv_data->cur_transfer = NULL;
last_transfer = list_entry(msg->transfers.prev,
struct spi_transfer,
last_transfer = list_last_entry(&msg->transfers, struct spi_transfer,
transfer_list);
/* Delay if requested before any change in chip select */
......
drivers/spi/spi-qup.c 0 → 100644
View file @ 09c0998e
This diff is collapsed.
drivers/spi/spi-rspi.c
View file @ 09c0998e
This diff is collapsed.
drivers/spi/spi-s3c24xx.c
View file @ 09c0998e
......@@ -9,7 +9,6 @@
*
*/
#include <linux/init.h>
#include <linux/spinlock.h>
#include <linux/workqueue.h>
#include <linux/interrupt.h>
......@@ -123,25 +122,15 @@ static int s3c24xx_spi_update_state(struct spi_device *spi,
{
struct s3c24xx_spi *hw = to_hw(spi);
struct s3c24xx_spi_devstate *cs = spi->controller_state;
unsigned int bpw;
unsigned int hz;
unsigned int div;
unsigned long clk;
bpw = t ? t->bits_per_word : spi->bits_per_word;
hz = t ? t->speed_hz : spi->max_speed_hz;
if (!bpw)
bpw = 8;
if (!hz)
hz = spi->max_speed_hz;
if (bpw != 8) {
dev_err(&spi->dev, "invalid bits-per-word (%d)\n", bpw);
return -EINVAL;
}
if (spi->mode != cs->mode) {
u8 spcon = SPCON_DEFAULT | S3C2410_SPCON_ENSCK;
......@@ -544,6 +533,7 @@ static int s3c24xx_spi_probe(struct platform_device *pdev)
master->num_chipselect = hw->pdata->num_cs;
master->bus_num = pdata->bus_num;
master->bits_per_word_mask = SPI_BPW_MASK(8);
/* setup the state for the bitbang driver */
......@@ -643,6 +633,11 @@ static int s3c24xx_spi_remove(struct platform_device *dev)
static int s3c24xx_spi_suspend(struct device *dev)
{
struct s3c24xx_spi *hw = dev_get_drvdata(dev);
int ret;
ret = spi_master_suspend(hw->master);
if (ret)
return ret;
if (hw->pdata && hw->pdata->gpio_setup)
hw->pdata->gpio_setup(hw->pdata, 0);
......@@ -656,7 +651,7 @@ static int s3c24xx_spi_resume(struct device *dev)
struct s3c24xx_spi *hw = dev_get_drvdata(dev);
s3c24xx_spi_initialsetup(hw);
return 0;
return spi_master_resume(hw->master);
}
static const struct dev_pm_ops s3c24xx_spi_pmops = {
......
drivers/spi/spi-s3c64xx.c
View file @ 09c0998e
This diff is collapsed.
drivers/spi/spi-sc18is602.c
View file @ 09c0998e
......@@ -183,17 +183,9 @@ static int sc18is602_setup_transfer(struct sc18is602 *hw, u32 hz, u8 mode)
static int sc18is602_check_transfer(struct spi_device *spi,
struct spi_transfer *t, int tlen)
{
uint32_t hz;
if (t && t->len + tlen > SC18IS602_BUFSIZ)
return -EINVAL;
hz = spi->max_speed_hz;
if (t && t->speed_hz)
hz = t->speed_hz;
if (hz == 0)
return -EINVAL;
return 0;
}
......@@ -205,22 +197,15 @@ static int sc18is602_transfer_one(struct spi_master *master,
struct spi_transfer *t;
int status = 0;
/* SC18IS602 does not support CS2 */
if (hw->id == sc18is602 && spi->chip_select == 2) {
status = -ENXIO;
goto error;
}
hw->tlen = 0;
list_for_each_entry(t, &m->transfers, transfer_list) {
u32 hz = t->speed_hz ? : spi->max_speed_hz;
bool do_transfer;
status = sc18is602_check_transfer(spi, t, hw->tlen);
if (status < 0)
break;
status = sc18is602_setup_transfer(hw, hz, spi->mode);
status = sc18is602_setup_transfer(hw, t->speed_hz, spi->mode);
if (status < 0)
break;
......@@ -238,7 +223,6 @@ static int sc18is602_transfer_one(struct spi_master *master,
if (t->delay_usecs)
udelay(t->delay_usecs);
}
error:
m->status = status;
spi_finalize_current_message(master);
......@@ -247,10 +231,13 @@ static int sc18is602_transfer_one(struct spi_master *master,
static int sc18is602_setup(struct spi_device *spi)
{
if (spi->mode & ~(SPI_CPHA | SPI_CPOL | SPI_LSB_FIRST))
return -EINVAL;
struct sc18is602 *hw = spi_master_get_devdata(spi->master);
return sc18is602_check_transfer(spi, NULL, 0);
/* SC18IS602 does not support CS2 */
if (hw->id == sc18is602 && spi->chip_select == 2)
return -ENXIO;
return 0;
}
static int sc18is602_probe(struct i2c_client *client,
......@@ -309,6 +296,8 @@ static int sc18is602_probe(struct i2c_client *client,
master->setup = sc18is602_setup;
master->transfer_one_message = sc18is602_transfer_one;
master->dev.of_node = np;
master->min_speed_hz = hw->freq / 128;
master->max_speed_hz = hw->freq / 4;
error = devm_spi_register_master(dev, master);
if (error)
......
drivers/spi/spi-sh-hspi.c
View file @ 09c0998e
......@@ -46,8 +46,6 @@
/* SPSR */
#define RXFL (1 << 2)
#define hspi2info(h) (h->dev->platform_data)
struct hspi_priv {
void __iomem *addr;
struct spi_master *master;
......@@ -113,14 +111,9 @@ static void hspi_hw_setup(struct hspi_priv *hspi,
{
struct spi_device *spi = msg->spi;
struct device *dev = hspi->dev;
u32 target_rate;
u32 spcr, idiv_clk;
u32 rate, best_rate, min, tmp;
target_rate = t ? t->speed_hz : 0;
if (!target_rate)
target_rate = spi->max_speed_hz;
/*
* find best IDIV/CLKCx settings
*/
......@@ -140,7 +133,7 @@ static void hspi_hw_setup(struct hspi_priv *hspi,
rate /= (((idiv_clk & 0x1F) + 1) * 2);
/* save best settings */
tmp = abs(target_rate - rate);
tmp = abs(t->speed_hz - rate);
if (tmp < min) {
min = tmp;
spcr = idiv_clk;
......@@ -153,7 +146,7 @@ static void hspi_hw_setup(struct hspi_priv *hspi,
if (spi->mode & SPI_CPOL)
spcr |= 1 << 6;
dev_dbg(dev, "speed %d/%d\n", target_rate, best_rate);
dev_dbg(dev, "speed %d/%d\n", t->speed_hz, best_rate);
hspi_write(hspi, SPCR, spcr);
hspi_write(hspi, SPSR, 0x0);
......@@ -230,29 +223,6 @@ static int hspi_transfer_one_message(struct spi_master *master,
return ret;
}
static int hspi_setup(struct spi_device *spi)
{
struct hspi_priv *hspi = spi_master_get_devdata(spi->master);
struct device *dev = hspi->dev;
if (8 != spi->bits_per_word) {
dev_err(dev, "bits_per_word should be 8\n");
return -EIO;
}
dev_dbg(dev, "%s setup\n", spi->modalias);
return 0;
}
static void hspi_cleanup(struct spi_device *spi)
{
struct hspi_priv *hspi = spi_master_get_devdata(spi->master);
struct device *dev = hspi->dev;
dev_dbg(dev, "%s cleanup\n", spi->modalias);
}
static int hspi_probe(struct platform_device *pdev)
{
struct resource *res;
......@@ -298,22 +268,23 @@ static int hspi_probe(struct platform_device *pdev)
pm_runtime_enable(&pdev->dev);
master->num_chipselect = 1;
master->bus_num = pdev->id;
master->setup = hspi_setup;
master->cleanup = hspi_cleanup;
master->mode_bits = SPI_CPOL | SPI_CPHA;
master->dev.of_node = pdev->dev.of_node;
master->auto_runtime_pm = true;
master->transfer_one_message = hspi_transfer_one_message;
master->bits_per_word_mask = SPI_BPW_MASK(8);
ret = devm_spi_register_master(&pdev->dev, master);
if (ret < 0) {
dev_err(&pdev->dev, "spi_register_master error.\n");
goto error1;
goto error2;
}
return 0;
error2:
pm_runtime_disable(&pdev->dev);
error1:
clk_put(clk);
error0:
......
drivers/spi/spi-sh-msiof.c
View file @ 09c0998e
This diff is collapsed.
drivers/spi/spi-sh-sci.c
View file @ 09c0998e
This diff is collapsed.
drivers/spi/spi-sirf.c
View file @ 09c0998e
This diff is collapsed.
drivers/spi/spi-sun4i.c 0 → 100644
View file @ 09c0998e
This diff is collapsed.
drivers/spi/spi-sun6i.c 0 → 100644
View file @ 09c0998e
This diff is collapsed.
drivers/spi/spi-tegra114.c
View file @ 09c0998e
This diff is collapsed.
drivers/spi/spi-tegra20-sflash.c
View file @ 09c0998e
This diff is collapsed.
drivers/spi/spi-tegra20-slink.c
View file @ 09c0998e
This diff is collapsed.
drivers/spi/spi-ti-qspi.c
View file @ 09c0998e
This diff is collapsed.
drivers/spi/spi-ti-ssp.c deleted 100644 → 0
View file @ 455c6fdb
This diff is collapsed.
drivers/spi/spi-topcliff-pch.c
View file @ 09c0998e
This diff is collapsed.
drivers/spi/spi-txx9.c
View file @ 09c0998e
This diff is collapsed.
drivers/spi/spi-xcomm.c
View file @ 09c0998e
This diff is collapsed.
drivers/spi/spi-xilinx.c
View file @ 09c0998e
This diff is collapsed.
drivers/spi/spi-xtensa-xtfpga.c 0 → 100644
View file @ 09c0998e
This diff is collapsed.
drivers/spi/spi.c
View file @ 09c0998e
This diff is collapsed.
drivers/spi/spidev.c
View file @ 09c0998e
This diff is collapsed.
include/linux/platform_data/spi-s3c64xx.h
View file @ 09c0998e
This diff is collapsed.
include/linux/pm_runtime.h
View file @ 09c0998e
......@@ -26,9 +26,13 @@
#ifdef CONFIG_PM
extern int pm_generic_runtime_suspend(struct device *dev);
extern int pm_generic_runtime_resume(struct device *dev);
extern int pm_runtime_force_suspend(struct device *dev);
extern int pm_runtime_force_resume(struct device *dev);
#else
static inline int pm_generic_runtime_suspend(struct device *dev) { return 0; }
static inline int pm_generic_runtime_resume(struct device *dev) { return 0; }
static inline int pm_runtime_force_suspend(struct device *dev) { return 0; }
static inline int pm_runtime_force_resume(struct device *dev) { return 0; }
#endif
#ifdef CONFIG_PM_RUNTIME
......
include/linux/spi/spi.h
View file @ 09c0998e
This diff is collapsed.
include/linux/spi/spi_bitbang.h
View file @ 09c0998e
This diff is collapsed.
include/uapi/linux/spi/spidev.h
View file @ 09c0998e
This diff is collapsed.
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7