ARM: dts: armada-370.dtsi: Add definitions for PCIe legacy INTx interrupts

Add definitions for PCIe legacy INTx interrupts.

This is required for example in a scenario where a driver requests only
one of the legacy interrupts (INTA). Without this, the driver would be
notified on events on all 4 (INTA, INTB, INTC, INTD), even if it
requested only one of them.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

arch/arm/boot/dts/armada-370.dtsi

@@ -60,16 +60,26 @@ pcie0: pcie@1,0 {
 				reg = <0x0800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 58>;
 				#interrupt-cells = <1>;
                                 ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
                                           0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 58>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie0_intc 0>,
+						<0 0 0 2 &pcie0_intc 1>,
+						<0 0 0 3 &pcie0_intc 2>,
+						<0 0 0 4 &pcie0_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 5>;
 				status = "disabled";
+
+				pcie0_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie2: pcie@2,0 {
@@ -78,16 +88,26 @@ pcie2: pcie@2,0 {
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 62>;
 				#interrupt-cells = <1>;
                                 ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
                                           0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 62>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie2_intc 0>,
+						<0 0 0 2 &pcie2_intc 1>,
+						<0 0 0 3 &pcie2_intc 2>,
+						<0 0 0 4 &pcie2_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 9>;
 				status = "disabled";
+
+				pcie2_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};