Commit 09df5cbe authored by Mauro Carvalho Chehab's avatar Mauro Carvalho Chehab

V4L/DVB (5858): Use msecs_to_jiffies instead of HZ on media/video I2C drivers

Signed-off-by: default avatarMauro Carvalho Chehab <mchehab@infradead.org>
parent a2d66a37
......@@ -257,7 +257,7 @@ static int bt866_write(struct bt866 *encoder,
printk(KERN_WARNING "%s: I/O error #%d "
"(write 0x%02x/0x%02x)\n",
encoder->i2c->name, err, encoder->addr, subaddr);
schedule_timeout_interruptible(HZ/10);
schedule_timeout_interruptible(msecs_to_jiffies(100));
}
if (err == 3) {
printk(KERN_WARNING "%s: giving up\n",
......
......@@ -86,9 +86,9 @@ static const int disp_modes[8][3] =
#define PAGE_WAIT (300*HZ/1000) /* Time between requesting page and */
#define PAGE_WAIT msecs_to_jiffies(300) /* Time between requesting page and */
/* checking status bits */
#define PGBUF_EXPIRE (15*HZ) /* Time to wait before retransmitting */
#define PGBUF_EXPIRE msecs_to_jiffies(15000) /* Time to wait before retransmitting */
/* page regardless of infobits */
typedef struct {
u8 pgbuf[VTX_VIRTUALSIZE]; /* Page-buffer */
......@@ -115,8 +115,8 @@ struct saa5249_device
#define CCTWR 34 /* IC write/read-address of vtx-chip */
#define CCTRD 35
#define NOACK_REPEAT 10 /* Retry access this many times on failure */
#define CLEAR_DELAY (HZ/20) /* Time required to clear a page */
#define READY_TIMEOUT (30*HZ/1000) /* Time to wait for ready signal of IC-bus interface */
#define CLEAR_DELAY msecs_to_jiffies(50) /* Time required to clear a page */
#define READY_TIMEOUT msecs_to_jiffies(30) /* Time to wait for ready signal of I2C-bus interface */
#define INIT_DELAY 500 /* Time in usec to wait at initialization of CEA interface */
#define START_DELAY 10 /* Time in usec to wait before starting write-cycle (CEA) */
......
......@@ -208,7 +208,7 @@ determine_norm (struct i2c_client *client)
saa7110_write_block(client, initseq, sizeof(initseq));
saa7110_selmux(client, decoder->input);
prepare_to_wait(&decoder->wq, &wait, TASK_UNINTERRUPTIBLE);
schedule_timeout(HZ/4);
schedule_timeout(msecs_to_jiffies(250));
finish_wait(&decoder->wq, &wait);
status = saa7110_read(client);
if (status & 0x40) {
......@@ -249,7 +249,7 @@ determine_norm (struct i2c_client *client)
//saa7110_write(client,0x2E,0x9A);
prepare_to_wait(&decoder->wq, &wait, TASK_UNINTERRUPTIBLE);
schedule_timeout(HZ/4);
schedule_timeout(msecs_to_jiffies(250));
finish_wait(&decoder->wq, &wait);
status = saa7110_read(client);
......
......@@ -290,7 +290,7 @@ static int chip_thread(void *data)
desc->checkmode(chip);
/* schedule next check */
mod_timer(&chip->wt, jiffies+2*HZ);
mod_timer(&chip->wt, jiffies+msecs_to_jiffies(2000));
}
v4l_dbg(1, debug, &chip->c, "%s: thread exiting\n", chip->c.name);
......@@ -1770,7 +1770,7 @@ static int chip_command(struct i2c_client *client,
desc->setmode(chip,VIDEO_SOUND_MONO);
if (chip->prevmode != VIDEO_SOUND_MONO)
chip->prevmode = -1; /* reset previous mode */
mod_timer(&chip->wt, jiffies+2*HZ);
mod_timer(&chip->wt, jiffies+msecs_to_jiffies(2000));
/* the thread will call checkmode() later */
}
break;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment