Commit 0acf1676 authored by Vince Bridgers's avatar Vince Bridgers Committed by David S. Miller

net: stmmac: add platform init/exit for Altera's ARM socfpga

This patch adds platform init/exit functions and modifications to support
suspend/resume for the Altera Cyclone 5 SOC Ethernet controller. The platform
exit function puts the controller into reset using the socfpga reset
controller driver. The platform init function sets up the Synopsys mac by
first making sure the Ethernet controller is held in reset, programming the
phy mode through external support logic, then deasserts reset through
the socfpga reset manager driver.
Signed-off-by: default avatarVince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 48bc0343
......@@ -20,7 +20,9 @@
#include <linux/of_net.h>
#include <linux/phy.h>
#include <linux/regmap.h>
#include <linux/reset.h>
#include <linux/stmmac.h>
#include "stmmac.h"
#define SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_GMII_MII 0x0
#define SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_RGMII 0x1
......@@ -34,6 +36,7 @@ struct socfpga_dwmac {
u32 reg_shift;
struct device *dev;
struct regmap *sys_mgr_base_addr;
struct reset_control *stmmac_rst;
};
static int socfpga_dwmac_parse_data(struct socfpga_dwmac *dwmac, struct device *dev)
......@@ -43,6 +46,13 @@ static int socfpga_dwmac_parse_data(struct socfpga_dwmac *dwmac, struct device *
u32 reg_offset, reg_shift;
int ret;
dwmac->stmmac_rst = devm_reset_control_get(dev,
STMMAC_RESOURCE_NAME);
if (IS_ERR(dwmac->stmmac_rst)) {
dev_info(dev, "Could not get reset control!\n");
return -EINVAL;
}
dwmac->interface = of_get_phy_mode(np);
sys_mgr_base_addr = syscon_regmap_lookup_by_phandle(np, "altr,sysmgr-syscon");
......@@ -125,6 +135,65 @@ static void *socfpga_dwmac_probe(struct platform_device *pdev)
return dwmac;
}
static void socfpga_dwmac_exit(struct platform_device *pdev, void *priv)
{
struct socfpga_dwmac *dwmac = priv;
/* On socfpga platform exit, assert and hold reset to the
* enet controller - the default state after a hard reset.
*/
if (dwmac->stmmac_rst)
reset_control_assert(dwmac->stmmac_rst);
}
static int socfpga_dwmac_init(struct platform_device *pdev, void *priv)
{
struct socfpga_dwmac *dwmac = priv;
struct net_device *ndev = platform_get_drvdata(pdev);
struct stmmac_priv *stpriv = NULL;
int ret = 0;
if (ndev)
stpriv = netdev_priv(ndev);
/* Assert reset to the enet controller before changing the phy mode */
if (dwmac->stmmac_rst)
reset_control_assert(dwmac->stmmac_rst);
/* Setup the phy mode in the system manager registers according to
* devicetree configuration
*/
ret = socfpga_dwmac_setup(dwmac);
/* Deassert reset for the phy configuration to be sampled by
* the enet controller, and operation to start in requested mode
*/
if (dwmac->stmmac_rst)
reset_control_deassert(dwmac->stmmac_rst);
/* Before the enet controller is suspended, the phy is suspended.
* This causes the phy clock to be gated. The enet controller is
* resumed before the phy, so the clock is still gated "off" when
* the enet controller is resumed. This code makes sure the phy
* is "resumed" before reinitializing the enet controller since
* the enet controller depends on an active phy clock to complete
* a DMA reset. A DMA reset will "time out" if executed
* with no phy clock input on the Synopsys enet controller.
* Verified through Synopsys Case #8000711656.
*
* Note that the phy clock is also gated when the phy is isolated.
* Phy "suspend" and "isolate" controls are located in phy basic
* control register 0, and can be modified by the phy driver
* framework.
*/
if (stpriv && stpriv->phydev)
phy_resume(stpriv->phydev);
return ret;
}
const struct stmmac_of_data socfpga_gmac_data = {
.setup = socfpga_dwmac_probe,
.init = socfpga_dwmac_init,
.exit = socfpga_dwmac_exit,
};
......@@ -2878,6 +2878,10 @@ int stmmac_suspend(struct net_device *ndev)
clk_disable_unprepare(priv->stmmac_clk);
}
spin_unlock_irqrestore(&priv->lock, flags);
priv->oldlink = 0;
priv->speed = 0;
priv->oldduplex = -1;
return 0;
}
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment