Commit 0b9f28fe authored by Nicolas Saenz Julienne's avatar Nicolas Saenz Julienne Committed by Dmitry Torokhov

Input: add official Raspberry Pi's touchscreen driver

Add's support to Raspberry Pi's 7" Touch device. Instead of using a
conventional bus all information is copied into a memory mapped area by
RPi's firmware.

Based on the driver found in RPi's kernel repository.
Signed-off-by: default avatarNicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: default avatarRob Herring <robh@kernel.org>
Acked-by: default avatarEric Anholt <eric@anholt.net>
Signed-off-by: default avatarDmitry Torokhov <dmitry.torokhov@gmail.com>
parent 4d8f727b
Raspberry Pi firmware based 7" touchscreen
=====================================
Required properties:
- compatible: "raspberrypi,firmware-ts"
Optional properties:
- firmware: Reference to RPi's firmware device node
- touchscreen-size-x: See touchscreen.txt
- touchscreen-size-y: See touchscreen.txt
- touchscreen-inverted-x: See touchscreen.txt
- touchscreen-inverted-y: See touchscreen.txt
- touchscreen-swapped-x-y: See touchscreen.txt
Example:
firmware: firmware-rpi {
compatible = "raspberrypi,bcm2835-firmware";
mboxes = <&mailbox>;
ts: touchscreen {
compatible = "raspberrypi,firmware-ts";
touchscreen-size-x = <800>;
touchscreen-size-y = <480>;
};
};
...@@ -683,6 +683,18 @@ config TOUCHSCREEN_EDT_FT5X06 ...@@ -683,6 +683,18 @@ config TOUCHSCREEN_EDT_FT5X06
To compile this driver as a module, choose M here: the To compile this driver as a module, choose M here: the
module will be called edt-ft5x06. module will be called edt-ft5x06.
config TOUCHSCREEN_RASPBERRYPI_FW
tristate "Raspberry Pi's firmware base touch screen support"
depends on RASPBERRYPI_FIRMWARE || COMPILE_TEST
help
Say Y here if you have the official Raspberry Pi 7 inch screen on
your system.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called raspberrypi-ts.
config TOUCHSCREEN_MIGOR config TOUCHSCREEN_MIGOR
tristate "Renesas MIGO-R touchscreen" tristate "Renesas MIGO-R touchscreen"
depends on (SH_MIGOR || COMPILE_TEST) && I2C depends on (SH_MIGOR || COMPILE_TEST) && I2C
......
...@@ -108,3 +108,4 @@ obj-$(CONFIG_TOUCHSCREEN_ZET6223) += zet6223.o ...@@ -108,3 +108,4 @@ obj-$(CONFIG_TOUCHSCREEN_ZET6223) += zet6223.o
obj-$(CONFIG_TOUCHSCREEN_ZFORCE) += zforce_ts.o obj-$(CONFIG_TOUCHSCREEN_ZFORCE) += zforce_ts.o
obj-$(CONFIG_TOUCHSCREEN_COLIBRI_VF50) += colibri-vf50-ts.o obj-$(CONFIG_TOUCHSCREEN_COLIBRI_VF50) += colibri-vf50-ts.o
obj-$(CONFIG_TOUCHSCREEN_ROHM_BU21023) += rohm_bu21023.o obj-$(CONFIG_TOUCHSCREEN_ROHM_BU21023) += rohm_bu21023.o
obj-$(CONFIG_TOUCHSCREEN_RASPBERRYPI_FW) += raspberrypi-ts.o
// SPDX-License-Identifier: GPL-2.0
/*
* Raspberry Pi firmware based touchscreen driver
*
* Copyright (C) 2015, 2017 Raspberry Pi
* Copyright (C) 2018 Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
*/
#include <linux/io.h>
#include <linux/of.h>
#include <linux/slab.h>
#include <linux/device.h>
#include <linux/module.h>
#include <linux/bitops.h>
#include <linux/dma-mapping.h>
#include <linux/platform_device.h>
#include <linux/input.h>
#include <linux/input/mt.h>
#include <linux/input-polldev.h>
#include <linux/input/touchscreen.h>
#include <soc/bcm2835/raspberrypi-firmware.h>
#define RPI_TS_DEFAULT_WIDTH 800
#define RPI_TS_DEFAULT_HEIGHT 480
#define RPI_TS_MAX_SUPPORTED_POINTS 10
#define RPI_TS_FTS_TOUCH_DOWN 0
#define RPI_TS_FTS_TOUCH_CONTACT 2
#define RPI_TS_POLL_INTERVAL 17 /* 60fps */
#define RPI_TS_NPOINTS_REG_INVALIDATE 99
struct rpi_ts {
struct platform_device *pdev;
struct input_polled_dev *poll_dev;
struct touchscreen_properties prop;
void __iomem *fw_regs_va;
dma_addr_t fw_regs_phys;
int known_ids;
};
struct rpi_ts_regs {
u8 device_mode;
u8 gesture_id;
u8 num_points;
struct rpi_ts_touch {
u8 xh;
u8 xl;
u8 yh;
u8 yl;
u8 pressure; /* Not supported */
u8 area; /* Not supported */
} point[RPI_TS_MAX_SUPPORTED_POINTS];
};
static void rpi_ts_poll(struct input_polled_dev *dev)
{
struct input_dev *input = dev->input;
struct rpi_ts *ts = dev->private;
struct rpi_ts_regs regs;
int modified_ids = 0;
long released_ids;
int event_type;
int touchid;
int x, y;
int i;
memcpy_fromio(&regs, ts->fw_regs_va, sizeof(regs));
/*
* We poll the memory based register copy of the touchscreen chip using
* the number of points register to know whether the copy has been
* updated (we write 99 to the memory copy, the GPU will write between
* 0 - 10 points)
*/
iowrite8(RPI_TS_NPOINTS_REG_INVALIDATE,
ts->fw_regs_va + offsetof(struct rpi_ts_regs, num_points));
if (regs.num_points == RPI_TS_NPOINTS_REG_INVALIDATE ||
(regs.num_points == 0 && ts->known_ids == 0))
return;
for (i = 0; i < regs.num_points; i++) {
x = (((int)regs.point[i].xh & 0xf) << 8) + regs.point[i].xl;
y = (((int)regs.point[i].yh & 0xf) << 8) + regs.point[i].yl;
touchid = (regs.point[i].yh >> 4) & 0xf;
event_type = (regs.point[i].xh >> 6) & 0x03;
modified_ids |= BIT(touchid);
if (event_type == RPI_TS_FTS_TOUCH_DOWN ||
event_type == RPI_TS_FTS_TOUCH_CONTACT) {
input_mt_slot(input, touchid);
input_mt_report_slot_state(input, MT_TOOL_FINGER, 1);
touchscreen_report_pos(input, &ts->prop, x, y, true);
}
}
released_ids = ts->known_ids & ~modified_ids;
for_each_set_bit(i, &released_ids, RPI_TS_MAX_SUPPORTED_POINTS) {
input_mt_slot(input, i);
input_mt_report_slot_state(input, MT_TOOL_FINGER, 0);
modified_ids &= ~(BIT(i));
}
ts->known_ids = modified_ids;
input_mt_sync_frame(input);
input_sync(input);
}
static void rpi_ts_dma_cleanup(void *data)
{
struct rpi_ts *ts = data;
struct device *dev = &ts->pdev->dev;
dma_free_coherent(dev, PAGE_SIZE, ts->fw_regs_va, ts->fw_regs_phys);
}
static int rpi_ts_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct device_node *np = dev->of_node;
struct input_polled_dev *poll_dev;
struct device_node *fw_node;
struct rpi_firmware *fw;
struct input_dev *input;
struct rpi_ts *ts;
u32 touchbuf;
int error;
fw_node = of_get_parent(np);
if (!fw_node) {
dev_err(dev, "Missing firmware node\n");
return -ENOENT;
}
fw = rpi_firmware_get(fw_node);
of_node_put(fw_node);
if (!fw)
return -EPROBE_DEFER;
ts = devm_kzalloc(dev, sizeof(*ts), GFP_KERNEL);
if (!ts)
return -ENOMEM;
ts->pdev = pdev;
ts->fw_regs_va = dma_zalloc_coherent(dev, PAGE_SIZE, &ts->fw_regs_phys,
GFP_KERNEL);
if (!ts->fw_regs_va) {
dev_err(dev, "failed to dma_alloc_coherent\n");
return -ENOMEM;
}
error = devm_add_action_or_reset(dev, rpi_ts_dma_cleanup, ts);
if (error) {
dev_err(dev, "failed to devm_add_action_or_reset, %d\n", error);
return error;
}
touchbuf = (u32)ts->fw_regs_phys;
error = rpi_firmware_property(fw, RPI_FIRMWARE_FRAMEBUFFER_SET_TOUCHBUF,
&touchbuf, sizeof(touchbuf));
if (error || touchbuf != 0) {
dev_warn(dev, "Failed to set touchbuf, %d\n", error);
return error;
}
poll_dev = devm_input_allocate_polled_device(dev);
if (!poll_dev) {
dev_err(dev, "Failed to allocate input device\n");
return -ENOMEM;
}
ts->poll_dev = poll_dev;
input = poll_dev->input;
input->name = "raspberrypi-ts";
input->id.bustype = BUS_HOST;
poll_dev->poll_interval = RPI_TS_POLL_INTERVAL;
poll_dev->poll = rpi_ts_poll;
poll_dev->private = ts;
input_set_abs_params(input, ABS_MT_POSITION_X, 0,
RPI_TS_DEFAULT_WIDTH, 0, 0);
input_set_abs_params(input, ABS_MT_POSITION_Y, 0,
RPI_TS_DEFAULT_HEIGHT, 0, 0);
touchscreen_parse_properties(input, true, &ts->prop);
error = input_mt_init_slots(input, RPI_TS_MAX_SUPPORTED_POINTS,
INPUT_MT_DIRECT);
if (error) {
dev_err(dev, "could not init mt slots, %d\n", error);
return error;
}
error = input_register_polled_device(poll_dev);
if (error) {
dev_err(dev, "could not register input device, %d\n", error);
return error;
}
return 0;
}
static const struct of_device_id rpi_ts_match[] = {
{ .compatible = "raspberrypi,firmware-ts", },
{},
};
MODULE_DEVICE_TABLE(of, rpi_ts_match);
static struct platform_driver rpi_ts_driver = {
.driver = {
.name = "raspberrypi-ts",
.of_match_table = rpi_ts_match,
},
.probe = rpi_ts_probe,
};
module_platform_driver(rpi_ts_driver);
MODULE_AUTHOR("Gordon Hollingworth");
MODULE_AUTHOR("Nicolas Saenz Julienne <nsaenzjulienne@suse.de>");
MODULE_DESCRIPTION("Raspberry Pi firmware based touchscreen driver");
MODULE_LICENSE("GPL v2");
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment