Commit 0d7bb85e authored by Arnd Bergmann's avatar Arnd Bergmann

ARM: omap1: remove unused board files

All board support that was marked as 'unused' earlier can
now be removed, leaving the five machines that that still
had someone using them in 2022, or that are supported in
qemu.

Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: default avatarArnd Bergmann <arnd@arndb.de>
parent 50f6f34e
...@@ -15263,7 +15263,6 @@ Q: http://patchwork.kernel.org/project/linux-omap/list/ ...@@ -15263,7 +15263,6 @@ Q: http://patchwork.kernel.org/project/linux-omap/list/
T: git git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap.git T: git git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap.git
F: arch/arm/configs/omap1_defconfig F: arch/arm/configs/omap1_defconfig
F: arch/arm/mach-omap1/ F: arch/arm/mach-omap1/
F: arch/arm/plat-omap/
F: drivers/i2c/busses/i2c-omap.c F: drivers/i2c/busses/i2c-omap.c
F: include/linux/platform_data/ams-delta-fiq.h F: include/linux/platform_data/ams-delta-fiq.h
F: include/linux/platform_data/i2c-omap.h F: include/linux/platform_data/i2c-omap.h
...@@ -15278,7 +15277,6 @@ Q: http://patchwork.kernel.org/project/linux-omap/list/ ...@@ -15278,7 +15277,6 @@ Q: http://patchwork.kernel.org/project/linux-omap/list/
T: git git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap.git T: git git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap.git
F: arch/arm/configs/omap2plus_defconfig F: arch/arm/configs/omap2plus_defconfig
F: arch/arm/mach-omap2/ F: arch/arm/mach-omap2/
F: arch/arm/plat-omap/
F: drivers/bus/ti-sysc.c F: drivers/bus/ti-sysc.c
F: drivers/i2c/busses/i2c-omap.c F: drivers/i2c/busses/i2c-omap.c
F: drivers/irqchip/irq-omap-intc.c F: drivers/irqchip/irq-omap-intc.c
......
...@@ -760,30 +760,6 @@ choice ...@@ -760,30 +760,6 @@ choice
depends on ARCH_OMAP2PLUS depends on ARCH_OMAP2PLUS
select DEBUG_UART_8250 select DEBUG_UART_8250
config DEBUG_OMAP7XXUART1
bool "Kernel low-level debugging via OMAP730 UART1"
depends on ARCH_OMAP730
select DEBUG_UART_8250
help
Say Y here if you want kernel low-level debugging support
on OMAP730 based platforms on the UART1.
config DEBUG_OMAP7XXUART2
bool "Kernel low-level debugging via OMAP730 UART2"
depends on ARCH_OMAP730
select DEBUG_UART_8250
help
Say Y here if you want kernel low-level debugging support
on OMAP730 based platforms on the UART2.
config DEBUG_OMAP7XXUART3
bool "Kernel low-level debugging via OMAP730 UART3"
depends on ARCH_OMAP730
select DEBUG_UART_8250
help
Say Y here if you want kernel low-level debugging support
on OMAP730 based platforms on the UART3.
config DEBUG_TI81XXUART1 config DEBUG_TI81XXUART1
bool "Kernel low-level debugging messages via TI81XX UART1 (ti8148evm)" bool "Kernel low-level debugging messages via TI81XX UART1 (ti8148evm)"
depends on ARCH_OMAP2PLUS depends on ARCH_OMAP2PLUS
...@@ -1728,9 +1704,9 @@ config DEBUG_UART_PHYS ...@@ -1728,9 +1704,9 @@ config DEBUG_UART_PHYS
default 0xffe40000 if DEBUG_RCAR_GEN1_SCIF0 default 0xffe40000 if DEBUG_RCAR_GEN1_SCIF0
default 0xffe42000 if DEBUG_RCAR_GEN1_SCIF2 default 0xffe42000 if DEBUG_RCAR_GEN1_SCIF2
default 0xfff36000 if DEBUG_HIGHBANK_UART default 0xfff36000 if DEBUG_HIGHBANK_UART
default 0xfffb0000 if DEBUG_OMAP1UART1 || DEBUG_OMAP7XXUART1 default 0xfffb0000 if DEBUG_OMAP1UART1
default 0xfffb0800 if DEBUG_OMAP1UART2 || DEBUG_OMAP7XXUART2 default 0xfffb0800 if DEBUG_OMAP1UART2
default 0xfffb9800 if DEBUG_OMAP1UART3 || DEBUG_OMAP7XXUART3 default 0xfffb9800 if DEBUG_OMAP1UART3
default 0xfffe8600 if DEBUG_BCM63XX_UART default 0xfffe8600 if DEBUG_BCM63XX_UART
default 0xffffee00 if DEBUG_AT91_SAM9263_DBGU default 0xffffee00 if DEBUG_AT91_SAM9263_DBGU
default 0xfffff200 if DEBUG_AT91_RM9200_DBGU default 0xfffff200 if DEBUG_AT91_RM9200_DBGU
...@@ -1847,9 +1823,9 @@ config DEBUG_UART_VIRT ...@@ -1847,9 +1823,9 @@ config DEBUG_UART_VIRT
default 0xfec00000 if ARCH_IXP4XX && !CPU_BIG_ENDIAN default 0xfec00000 if ARCH_IXP4XX && !CPU_BIG_ENDIAN
default 0xfec00003 if ARCH_IXP4XX && CPU_BIG_ENDIAN default 0xfec00003 if ARCH_IXP4XX && CPU_BIG_ENDIAN
default 0xfef36000 if DEBUG_HIGHBANK_UART default 0xfef36000 if DEBUG_HIGHBANK_UART
default 0xff0b0000 if DEBUG_OMAP1UART1 || DEBUG_OMAP7XXUART1 default 0xff0b0000 if DEBUG_OMAP1UART1
default 0xff0b0800 if DEBUG_OMAP1UART2 || DEBUG_OMAP7XXUART2 default 0xff0b0800 if DEBUG_OMAP1UART2
default 0xff0b9800 if DEBUG_OMAP1UART3 || DEBUG_OMAP7XXUART3 default 0xff0b9800 if DEBUG_OMAP1UART3
default 0xffd01000 if DEBUG_HIP01_UART default 0xffd01000 if DEBUG_HIP01_UART
default DEBUG_UART_PHYS if !MMU default DEBUG_UART_PHYS if !MMU
depends on DEBUG_LL_UART_8250 || DEBUG_LL_UART_PL01X || \ depends on DEBUG_LL_UART_8250 || DEBUG_LL_UART_PL01X || \
......
...@@ -20,8 +20,6 @@ CONFIG_ARCH_OMAP=y ...@@ -20,8 +20,6 @@ CONFIG_ARCH_OMAP=y
CONFIG_ARCH_OMAP1=y CONFIG_ARCH_OMAP1=y
CONFIG_OMAP_32K_TIMER=y CONFIG_OMAP_32K_TIMER=y
CONFIG_OMAP_DM_TIMER=y CONFIG_OMAP_DM_TIMER=y
CONFIG_ARCH_OMAP730=y
CONFIG_ARCH_OMAP850=y
CONFIG_ARCH_OMAP16XX=y CONFIG_ARCH_OMAP16XX=y
# CONFIG_OMAP_MUX is not set # CONFIG_OMAP_MUX is not set
CONFIG_OMAP_RESET_CLOCKS=y CONFIG_OMAP_RESET_CLOCKS=y
......
...@@ -19,19 +19,6 @@ menu "TI OMAP1 specific features" ...@@ -19,19 +19,6 @@ menu "TI OMAP1 specific features"
comment "OMAP Core Type" comment "OMAP Core Type"
config ARCH_OMAP730
depends on ARCH_MULTI_V5
bool "OMAP730 Based System"
select ARCH_OMAP_OTG
select CPU_ARM926T
select OMAP_MPU_TIMER
config ARCH_OMAP850
depends on ARCH_MULTI_V5
bool "OMAP850 Based System"
select ARCH_OMAP_OTG
select CPU_ARM926T
config ARCH_OMAP15XX config ARCH_OMAP15XX
depends on ARCH_MULTI_V4T depends on ARCH_MULTI_V4T
default y default y
...@@ -126,37 +113,6 @@ config ARCH_OMAP_OTG ...@@ -126,37 +113,6 @@ config ARCH_OMAP_OTG
comment "OMAP Board Type" comment "OMAP Board Type"
config MACH_OMAP_INNOVATOR
bool "TI Innovator"
depends on ARCH_OMAP15XX || ARCH_OMAP16XX
depends on UNUSED_BOARD_FILES
help
TI OMAP 1510 or 1610 Innovator board support. Say Y here if you
have such a board.
config MACH_OMAP_H2
bool "TI H2 Support"
depends on ARCH_OMAP16XX
depends on UNUSED_BOARD_FILES
help
TI OMAP 1610/1611B H2 board support. Say Y here if you have such
a board.
config MACH_OMAP_H3
bool "TI H3 Support"
depends on ARCH_OMAP16XX
depends on UNUSED_BOARD_FILES
help
TI OMAP 1710 H3 board support. Say Y here if you have such
a board.
config MACH_HERALD
bool "HTC Herald"
depends on ARCH_OMAP850
depends on UNUSED_BOARD_FILES
help
HTC Herald smartphone support (AKA T-Mobile Wing, ...)
config MACH_OMAP_OSK config MACH_OMAP_OSK
bool "TI OSK Support" bool "TI OSK Support"
depends on ARCH_OMAP16XX depends on ARCH_OMAP16XX
...@@ -167,28 +123,11 @@ config MACH_OMAP_OSK ...@@ -167,28 +123,11 @@ config MACH_OMAP_OSK
config OMAP_OSK_MISTRAL config OMAP_OSK_MISTRAL
bool "Mistral QVGA board Support" bool "Mistral QVGA board Support"
depends on MACH_OMAP_OSK depends on MACH_OMAP_OSK
depends on UNUSED_BOARD_FILES
help help
The OSK supports an optional add-on board with a Quarter-VGA The OSK supports an optional add-on board with a Quarter-VGA
touchscreen, PDA-ish buttons, a resume button, bicolor LED, touchscreen, PDA-ish buttons, a resume button, bicolor LED,
and camera connector. Say Y here if you have this board. and camera connector. Say Y here if you have this board.
config MACH_OMAP_PERSEUS2
bool "TI Perseus2"
depends on ARCH_OMAP730
depends on UNUSED_BOARD_FILES
help
Support for TI OMAP 730 Perseus2 board. Say Y here if you have such
a board.
config MACH_OMAP_FSAMPLE
bool "TI F-Sample"
depends on ARCH_OMAP730
depends on UNUSED_BOARD_FILES
help
Support for TI OMAP 850 F-Sample board. Say Y here if you have such
a board.
config MACH_OMAP_PALMTE config MACH_OMAP_PALMTE
bool "Palm Tungsten E" bool "Palm Tungsten E"
depends on ARCH_OMAP15XX depends on ARCH_OMAP15XX
...@@ -198,26 +137,6 @@ config MACH_OMAP_PALMTE ...@@ -198,26 +137,6 @@ config MACH_OMAP_PALMTE
http://palmtelinux.sourceforge.net/ for more information. http://palmtelinux.sourceforge.net/ for more information.
Say Y here if you have this PDA model, say N otherwise. Say Y here if you have this PDA model, say N otherwise.
config MACH_OMAP_PALMZ71
bool "Palm Zire71"
depends on ARCH_OMAP15XX
depends on UNUSED_BOARD_FILES
help
Support for the Palm Zire71 PDA. To boot the kernel,
you'll need a PalmOS compatible bootloader; check out
http://hackndev.com/palm/z71 for more information.
Say Y here if you have such a PDA, say N otherwise.
config MACH_OMAP_PALMTT
bool "Palm Tungsten|T"
depends on ARCH_OMAP15XX
depends on UNUSED_BOARD_FILES
help
Support for the Palm Tungsten|T PDA. To boot the kernel, you'll
need a PalmOS compatible bootloader (Garux); check out
http://garux.sourceforge.net/ for more information.
Say Y here if you have this PDA model, say N otherwise.
config MACH_SX1 config MACH_SX1
bool "Siemens SX1" bool "Siemens SX1"
depends on ARCH_OMAP15XX depends on ARCH_OMAP15XX
...@@ -249,16 +168,6 @@ config MACH_AMS_DELTA ...@@ -249,16 +168,6 @@ config MACH_AMS_DELTA
Support for the Amstrad E3 (codename Delta) videophone. Say Y here Support for the Amstrad E3 (codename Delta) videophone. Say Y here
if you have such a device. if you have such a device.
config MACH_OMAP_GENERIC
bool "Generic OMAP board"
depends on ARCH_OMAP15XX || ARCH_OMAP16XX
depends on UNUSED_BOARD_FILES
help
Support for generic OMAP-1510, 1610 or 1710 board with
no FPGA. Can be used as template for porting Linux to
custom OMAP boards. Say Y here if you have a custom
board.
endmenu endmenu
endif endif
...@@ -29,31 +29,13 @@ usb-fs-$(CONFIG_USB_SUPPORT) := usb.o ...@@ -29,31 +29,13 @@ usb-fs-$(CONFIG_USB_SUPPORT) := usb.o
obj-y += $(usb-fs-m) $(usb-fs-y) obj-y += $(usb-fs-m) $(usb-fs-y)
# Specific board support # Specific board support
obj-$(CONFIG_MACH_OMAP_H2) += board-h2.o board-h2-mmc.o \
board-nand.o
obj-$(CONFIG_MACH_OMAP_INNOVATOR) += board-innovator.o
obj-$(CONFIG_MACH_OMAP_GENERIC) += board-generic.o
obj-$(CONFIG_MACH_OMAP_PERSEUS2) += board-perseus2.o board-nand.o
obj-$(CONFIG_MACH_OMAP_FSAMPLE) += board-fsample.o board-nand.o
obj-$(CONFIG_MACH_OMAP_OSK) += board-osk.o obj-$(CONFIG_MACH_OMAP_OSK) += board-osk.o
obj-$(CONFIG_MACH_OMAP_H3) += board-h3.o board-h3-mmc.o \
board-nand.o
obj-$(CONFIG_MACH_OMAP_PALMTE) += board-palmte.o obj-$(CONFIG_MACH_OMAP_PALMTE) += board-palmte.o
obj-$(CONFIG_MACH_OMAP_PALMZ71) += board-palmz71.o
obj-$(CONFIG_MACH_OMAP_PALMTT) += board-palmtt.o
obj-$(CONFIG_MACH_NOKIA770) += board-nokia770.o obj-$(CONFIG_MACH_NOKIA770) += board-nokia770.o
obj-$(CONFIG_MACH_AMS_DELTA) += board-ams-delta.o ams-delta-fiq.o \ obj-$(CONFIG_MACH_AMS_DELTA) += board-ams-delta.o ams-delta-fiq.o \
ams-delta-fiq-handler.o ams-delta-fiq-handler.o
obj-$(CONFIG_MACH_SX1) += board-sx1.o board-sx1-mmc.o obj-$(CONFIG_MACH_SX1) += board-sx1.o board-sx1-mmc.o
obj-$(CONFIG_MACH_HERALD) += board-htcherald.o
ifeq ($(CONFIG_ARCH_OMAP15XX),y)
# Innovator-1510 FPGA
obj-$(CONFIG_MACH_OMAP_INNOVATOR) += fpga.o
endif
# GPIO # GPIO
obj-$(CONFIG_ARCH_OMAP730) += gpio7xx.o
obj-$(CONFIG_ARCH_OMAP850) += gpio7xx.o
obj-$(CONFIG_ARCH_OMAP15XX) += gpio15xx.o obj-$(CONFIG_ARCH_OMAP15XX) += gpio15xx.o
obj-$(CONFIG_ARCH_OMAP16XX) += gpio16xx.o obj-$(CONFIG_ARCH_OMAP16XX) += gpio16xx.o
// SPDX-License-Identifier: GPL-2.0-only
/*
* linux/arch/arm/mach-omap1/board-fsample.c
*
* Modified from board-perseus2.c
*
* Original OMAP730 support by Jean Pihet <j-pihet@ti.com>
* Updated for 2.6 by Kevin Hilman <kjh@hilman.org>
*/
#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/platnand.h>
#include <linux/mtd/physmap.h>
#include <linux/input.h>
#include <linux/smc91x.h>
#include <linux/omapfb.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <linux/soc/ti/omap1-io.h>
#include <linux/platform_data/keypad-omap.h>
#include "tc.h"
#include "mux.h"
#include "flash.h"
#include "hardware.h"
#include "iomap.h"
#include "common.h"
#include "fpga.h"
/* fsample is pretty close to p2-sample */
#define fsample_cpld_read(reg) __raw_readb(reg)
#define fsample_cpld_write(val, reg) __raw_writeb(val, reg)
#define FSAMPLE_CPLD_BASE 0xE8100000
#define FSAMPLE_CPLD_SIZE SZ_4K
#define FSAMPLE_CPLD_START 0x05080000
#define FSAMPLE_CPLD_REG_A (FSAMPLE_CPLD_BASE + 0x00)
#define FSAMPLE_CPLD_SWITCH (FSAMPLE_CPLD_BASE + 0x02)
#define FSAMPLE_CPLD_UART (FSAMPLE_CPLD_BASE + 0x02)
#define FSAMPLE_CPLD_REG_B (FSAMPLE_CPLD_BASE + 0x04)
#define FSAMPLE_CPLD_VERSION (FSAMPLE_CPLD_BASE + 0x06)
#define FSAMPLE_CPLD_SET_CLR (FSAMPLE_CPLD_BASE + 0x06)
#define FSAMPLE_CPLD_BIT_BT_RESET 0
#define FSAMPLE_CPLD_BIT_LCD_RESET 1
#define FSAMPLE_CPLD_BIT_CAM_PWDN 2
#define FSAMPLE_CPLD_BIT_CHARGER_ENABLE 3
#define FSAMPLE_CPLD_BIT_SD_MMC_EN 4
#define FSAMPLE_CPLD_BIT_aGPS_PWREN 5
#define FSAMPLE_CPLD_BIT_BACKLIGHT 6
#define FSAMPLE_CPLD_BIT_aGPS_EN_RESET 7
#define FSAMPLE_CPLD_BIT_aGPS_SLEEPx_N 8
#define FSAMPLE_CPLD_BIT_OTG_RESET 9
#define fsample_cpld_set(bit) \
fsample_cpld_write((((bit) & 15) << 4) | 0x0f, FSAMPLE_CPLD_SET_CLR)
#define fsample_cpld_clear(bit) \
fsample_cpld_write(0xf0 | ((bit) & 15), FSAMPLE_CPLD_SET_CLR)
static const unsigned int fsample_keymap[] = {
KEY(0, 0, KEY_UP),
KEY(1, 0, KEY_RIGHT),
KEY(2, 0, KEY_LEFT),
KEY(3, 0, KEY_DOWN),
KEY(4, 0, KEY_ENTER),
KEY(0, 1, KEY_F10),
KEY(1, 1, KEY_SEND),
KEY(2, 1, KEY_END),
KEY(3, 1, KEY_VOLUMEDOWN),
KEY(4, 1, KEY_VOLUMEUP),
KEY(5, 1, KEY_RECORD),
KEY(0, 2, KEY_F9),
KEY(1, 2, KEY_3),
KEY(2, 2, KEY_6),
KEY(3, 2, KEY_9),
KEY(4, 2, KEY_KPDOT),
KEY(0, 3, KEY_BACK),
KEY(1, 3, KEY_2),
KEY(2, 3, KEY_5),
KEY(3, 3, KEY_8),
KEY(4, 3, KEY_0),
KEY(5, 3, KEY_KPSLASH),
KEY(0, 4, KEY_HOME),
KEY(1, 4, KEY_1),
KEY(2, 4, KEY_4),
KEY(3, 4, KEY_7),
KEY(4, 4, KEY_KPASTERISK),
KEY(5, 4, KEY_POWER),
};
static struct smc91x_platdata smc91x_info = {
.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
.leda = RPC_LED_100_10,
.ledb = RPC_LED_TX_RX,
};
static struct resource smc91x_resources[] = {
[0] = {
.start = H2P2_DBG_FPGA_ETHR_START, /* Physical */
.end = H2P2_DBG_FPGA_ETHR_START + 0xf,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = INT_7XX_MPU_EXT_NIRQ,
.end = 0,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
},
};
static void __init fsample_init_smc91x(void)
{
__raw_writeb(1, H2P2_DBG_FPGA_LAN_RESET);
mdelay(50);
__raw_writeb(__raw_readb(H2P2_DBG_FPGA_LAN_RESET) & ~1,
H2P2_DBG_FPGA_LAN_RESET);
mdelay(50);
}
static struct mtd_partition nor_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
{
.name = "bootloader",
.offset = 0,
.size = SZ_128K,
.mask_flags = MTD_WRITEABLE, /* force read-only */
},
/* bootloader params in the next sector */
{
.name = "params",
.offset = MTDPART_OFS_APPEND,
.size = SZ_128K,
.mask_flags = 0,
},
/* kernel */
{
.name = "kernel",
.offset = MTDPART_OFS_APPEND,
.size = SZ_2M,
.mask_flags = 0
},
/* rest of flash is a file system */
{
.name = "rootfs",
.offset = MTDPART_OFS_APPEND,
.size = MTDPART_SIZ_FULL,
.mask_flags = 0
},
};
static struct physmap_flash_data nor_data = {
.width = 2,
.set_vpp = omap1_set_vpp,
.parts = nor_partitions,
.nr_parts = ARRAY_SIZE(nor_partitions),
};
static struct resource nor_resource = {
.start = OMAP_CS0_PHYS,
.end = OMAP_CS0_PHYS + SZ_32M - 1,
.flags = IORESOURCE_MEM,
};
static struct platform_device nor_device = {
.name = "physmap-flash",
.id = 0,
.dev = {
.platform_data = &nor_data,
},
.num_resources = 1,
.resource = &nor_resource,
};
#define FSAMPLE_NAND_RB_GPIO_PIN 62
static int nand_dev_ready(struct nand_chip *chip)
{
return gpio_get_value(FSAMPLE_NAND_RB_GPIO_PIN);
}
static struct platform_nand_data nand_data = {
.chip = {
.nr_chips = 1,
.chip_offset = 0,
.options = NAND_SAMSUNG_LP_OPTIONS,
},
.ctrl = {
.cmd_ctrl = omap1_nand_cmd_ctl,
.dev_ready = nand_dev_ready,
},
};
static struct resource nand_resource = {
.start = OMAP_CS3_PHYS,
.end = OMAP_CS3_PHYS + SZ_4K - 1,
.flags = IORESOURCE_MEM,
};
static struct platform_device nand_device = {
.name = "gen_nand",
.id = 0,
.dev = {
.platform_data = &nand_data,
},
.num_resources = 1,
.resource = &nand_resource,
};
static struct platform_device smc91x_device = {
.name = "smc91x",
.id = 0,
.dev = {
.platform_data = &smc91x_info,
},
.num_resources = ARRAY_SIZE(smc91x_resources),
.resource = smc91x_resources,
};
static struct resource kp_resources[] = {
[0] = {
.start = INT_7XX_MPUIO_KEYPAD,
.end = INT_7XX_MPUIO_KEYPAD,
.flags = IORESOURCE_IRQ,
},
};
static const struct matrix_keymap_data fsample_keymap_data = {
.keymap = fsample_keymap,
.keymap_size = ARRAY_SIZE(fsample_keymap),
};
static struct omap_kp_platform_data kp_data = {
.rows = 8,
.cols = 8,
.keymap_data = &fsample_keymap_data,
.delay = 4,
};
static struct platform_device kp_device = {
.name = "omap-keypad",
.id = -1,
.dev = {
.platform_data = &kp_data,
},
.num_resources = ARRAY_SIZE(kp_resources),
.resource = kp_resources,
};
static struct platform_device *devices[] __initdata = {
&nor_device,
&nand_device,
&smc91x_device,
&kp_device,
};
static const struct omap_lcd_config fsample_lcd_config = {
.ctrl_name = "internal",
};
static void __init omap_fsample_init(void)
{
/* Early, board-dependent init */
/*
* Hold GSM Reset until needed
*/
omap_writew(omap_readw(OMAP7XX_DSP_M_CTL) & ~1, OMAP7XX_DSP_M_CTL);
/*
* UARTs -> done automagically by 8250 driver
*/
/*
* CSx timings, GPIO Mux ... setup
*/
/* Flash: CS0 timings setup */
omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_0);
omap_writel(0x00000088, OMAP7XX_FLASH_ACFG_0);
/*
* Ethernet support through the debug board
* CS1 timings setup
*/
omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_1);
omap_writel(0x00000000, OMAP7XX_FLASH_ACFG_1);
/*
* Configure MPU_EXT_NIRQ IO in IO_CONF9 register,
* It is used as the Ethernet controller interrupt
*/
omap_writel(omap_readl(OMAP7XX_IO_CONF_9) & 0x1FFFFFFF,
OMAP7XX_IO_CONF_9);
fsample_init_smc91x();
BUG_ON(gpio_request(FSAMPLE_NAND_RB_GPIO_PIN, "NAND ready") < 0);
gpio_direction_input(FSAMPLE_NAND_RB_GPIO_PIN);
omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
/* Mux pins for keypad */
omap_cfg_reg(E2_7XX_KBR0);
omap_cfg_reg(J7_7XX_KBR1);
omap_cfg_reg(E1_7XX_KBR2);
omap_cfg_reg(F3_7XX_KBR3);
omap_cfg_reg(D2_7XX_KBR4);
omap_cfg_reg(C2_7XX_KBC0);
omap_cfg_reg(D3_7XX_KBC1);
omap_cfg_reg(E4_7XX_KBC2);
omap_cfg_reg(F4_7XX_KBC3);
omap_cfg_reg(E3_7XX_KBC4);
platform_add_devices(devices, ARRAY_SIZE(devices));
omap_serial_init();
omap_register_i2c_bus(1, 100, NULL, 0);
omapfb_set_lcd_config(&fsample_lcd_config);
}
/* Only FPGA needs to be mapped here. All others are done with ioremap */
static struct map_desc omap_fsample_io_desc[] __initdata = {
{
.virtual = H2P2_DBG_FPGA_BASE,
.pfn = __phys_to_pfn(H2P2_DBG_FPGA_START),
.length = H2P2_DBG_FPGA_SIZE,
.type = MT_DEVICE
},
{
.virtual = FSAMPLE_CPLD_BASE,
.pfn = __phys_to_pfn(FSAMPLE_CPLD_START),
.length = FSAMPLE_CPLD_SIZE,
.type = MT_DEVICE
}
};
static void __init omap_fsample_map_io(void)
{
omap15xx_map_io();
iotable_init(omap_fsample_io_desc,
ARRAY_SIZE(omap_fsample_io_desc));
}
MACHINE_START(OMAP_FSAMPLE, "OMAP730 F-Sample")
/* Maintainer: Brian Swetland <swetland@google.com> */
.atag_offset = 0x100,
.map_io = omap_fsample_map_io,
.init_early = omap1_init_early,
.init_irq = omap1_init_irq,
.handle_irq = omap1_handle_irq,
.init_machine = omap_fsample_init,
.init_late = omap1_init_late,
.init_time = omap1_timer_init,
.restart = omap1_restart,
MACHINE_END
// SPDX-License-Identifier: GPL-2.0-only
/*
* linux/arch/arm/mach-omap1/board-generic.c
*
* Modified from board-innovator1510.c
*
* Code for generic OMAP board. Should work on many OMAP systems where
* the device drivers take care of all the necessary hardware initialization.
* Do not put any board specific code to this file; create a new machine
* type if you need custom low-level initializations.
*/
#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include "hardware.h"
#include "mux.h"
#include "usb.h"
#include "common.h"
/* assume no Mini-AB port */
#ifdef CONFIG_ARCH_OMAP15XX
static struct omap_usb_config generic1510_usb_config __initdata = {
.register_host = 1,
.register_dev = 1,
.hmc_mode = 16,
.pins[0] = 3,
};
#endif
#if defined(CONFIG_ARCH_OMAP16XX)
static struct omap_usb_config generic1610_usb_config __initdata = {
#ifdef CONFIG_USB_OTG
.otg = 1,
#endif
.register_host = 1,
.register_dev = 1,
.hmc_mode = 16,
.pins[0] = 6,
};
#endif
static void __init omap_generic_init(void)
{
#ifdef CONFIG_ARCH_OMAP15XX
if (cpu_is_omap15xx()) {
/* mux pins for uarts */
omap_cfg_reg(UART1_TX);
omap_cfg_reg(UART1_RTS);
omap_cfg_reg(UART2_TX);
omap_cfg_reg(UART2_RTS);
omap_cfg_reg(UART3_TX);
omap_cfg_reg(UART3_RX);
omap1_usb_init(&generic1510_usb_config);
}
#endif
#if defined(CONFIG_ARCH_OMAP16XX)
if (!cpu_is_omap1510()) {
omap1_usb_init(&generic1610_usb_config);
}
#endif
omap_serial_init();
omap_register_i2c_bus(1, 100, NULL, 0);
}
MACHINE_START(OMAP_GENERIC, "Generic OMAP1510/1610/1710")
/* Maintainer: Tony Lindgren <tony@atomide.com> */
.atag_offset = 0x100,
.map_io = omap16xx_map_io,
.init_early = omap1_init_early,
.init_irq = omap1_init_irq,
.handle_irq = omap1_handle_irq,
.init_machine = omap_generic_init,
.init_late = omap1_init_late,
.init_time = omap1_timer_init,
.restart = omap1_restart,
MACHINE_END
// SPDX-License-Identifier: GPL-2.0-only
/*
* linux/arch/arm/mach-omap1/board-h2-mmc.c
*
* Copyright (C) 2007 Instituto Nokia de Tecnologia - INdT
* Author: Felipe Balbi <felipe.lima@indt.org.br>
*
* This code is based on linux/arch/arm/mach-omap2/board-n800-mmc.c, which is:
* Copyright (C) 2006 Nokia Corporation
*/
#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/platform_data/gpio-omap.h>
#include <linux/mfd/tps65010.h>
#include "board-h2.h"
#include "mmc.h"
#if IS_ENABLED(CONFIG_MMC_OMAP)
static int mmc_set_power(struct device *dev, int slot, int power_on,
int vdd)
{
gpio_set_value(H2_TPS_GPIO_MMC_PWR_EN, power_on);
return 0;
}
static int mmc_late_init(struct device *dev)
{
int ret = gpio_request(H2_TPS_GPIO_MMC_PWR_EN, "MMC power");
if (ret < 0)
return ret;
gpio_direction_output(H2_TPS_GPIO_MMC_PWR_EN, 0);
return ret;
}
static void mmc_cleanup(struct device *dev)
{
gpio_free(H2_TPS_GPIO_MMC_PWR_EN);
}
/*
* H2 could use the following functions tested:
* - mmc_get_cover_state that uses OMAP_MPUIO(1)
* - mmc_get_wp that uses OMAP_MPUIO(3)
*/
static struct omap_mmc_platform_data mmc1_data = {
.nr_slots = 1,
.init = mmc_late_init,
.cleanup = mmc_cleanup,
.slots[0] = {
.set_power = mmc_set_power,
.ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
.name = "mmcblk",
},
};
static struct omap_mmc_platform_data *mmc_data[OMAP16XX_NR_MMC];
void __init h2_mmc_init(void)
{
mmc_data[0] = &mmc1_data;
omap1_init_mmc(mmc_data, OMAP16XX_NR_MMC);
}
#else
void __init h2_mmc_init(void)
{
}
#endif
This diff is collapsed.
/*
* arch/arm/mach-omap1/board-h2.h
*
* Hardware definitions for TI OMAP1610 H2 board.
*
* Cleanup for Linux-2.6 by Dirk Behme <dirk.behme@de.bosch.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
* THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
* NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
* USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
* ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#ifndef __ASM_ARCH_OMAP_H2_H
#define __ASM_ARCH_OMAP_H2_H
#define H2_TPS_GPIO_BASE (OMAP_MAX_GPIO_LINES + 16 /* MPUIO */)
# define H2_TPS_GPIO_MMC_PWR_EN (H2_TPS_GPIO_BASE + 3)
extern void h2_mmc_init(void);
#endif /* __ASM_ARCH_OMAP_H2_H */
// SPDX-License-Identifier: GPL-2.0-only
/*
* linux/arch/arm/mach-omap1/board-h3-mmc.c
*
* Copyright (C) 2007 Instituto Nokia de Tecnologia - INdT
* Author: Felipe Balbi <felipe.lima@indt.org.br>
*
* This code is based on linux/arch/arm/mach-omap2/board-n800-mmc.c, which is:
* Copyright (C) 2006 Nokia Corporation
*/
#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/mfd/tps65010.h>
#include "common.h"
#include "board-h3.h"
#include "mmc.h"
#if IS_ENABLED(CONFIG_MMC_OMAP)
static int mmc_set_power(struct device *dev, int slot, int power_on,
int vdd)
{
gpio_set_value(H3_TPS_GPIO_MMC_PWR_EN, power_on);
return 0;
}
/*
* H3 could use the following functions tested:
* - mmc_get_cover_state that uses OMAP_MPUIO(1)
* - mmc_get_wp that maybe uses OMAP_MPUIO(3)
*/
static struct omap_mmc_platform_data mmc1_data = {
.nr_slots = 1,
.slots[0] = {
.set_power = mmc_set_power,
.ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
.name = "mmcblk",
},
};
static struct omap_mmc_platform_data *mmc_data[OMAP16XX_NR_MMC];
void __init h3_mmc_init(void)
{
int ret;
ret = gpio_request(H3_TPS_GPIO_MMC_PWR_EN, "MMC power");
if (ret < 0)
return;
gpio_direction_output(H3_TPS_GPIO_MMC_PWR_EN, 0);
mmc_data[0] = &mmc1_data;
omap1_init_mmc(mmc_data, OMAP16XX_NR_MMC);
}
#else
void __init h3_mmc_init(void)
{
}
#endif
This diff is collapsed.
/*
* arch/arm/mach-omap1/board-h3.h
*
* Copyright (C) 2001 RidgeRun, Inc.
* Copyright (C) 2004 Texas Instruments, Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
* THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
* NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
* USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
* ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#ifndef __ASM_ARCH_OMAP_H3_H
#define __ASM_ARCH_OMAP_H3_H
#define H3_TPS_GPIO_BASE (OMAP_MAX_GPIO_LINES + 16 /* MPUIO */)
# define H3_TPS_GPIO_MMC_PWR_EN (H3_TPS_GPIO_BASE + 4)
extern void h3_mmc_init(void);
#endif /* __ASM_ARCH_OMAP_H3_H */
This diff is collapsed.
This diff is collapsed.
// SPDX-License-Identifier: GPL-2.0-only
/*
* linux/arch/arm/mach-omap1/board-nand.c
*
* Common OMAP1 board NAND code
*
* Copyright (C) 2004, 2012 Texas Instruments, Inc.
* Copyright (C) 2002 MontaVista Software, Inc.
* Copyright (C) 2001 RidgeRun, Inc.
* Author: RidgeRun, Inc.
* Greg Lonnon (glonnon@ridgerun.com) or info@ridgerun.com
*/
#include <linux/kernel.h>
#include <linux/io.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/rawnand.h>
#include "common.h"
void omap1_nand_cmd_ctl(struct nand_chip *this, int cmd, unsigned int ctrl)
{
unsigned long mask;
if (cmd == NAND_CMD_NONE)
return;
mask = (ctrl & NAND_CLE) ? 0x02 : 0;
if (ctrl & NAND_ALE)
mask |= 0x04;
writeb(cmd, this->legacy.IO_ADDR_W + mask);
}
// SPDX-License-Identifier: GPL-2.0-only
/*
* linux/arch/arm/mach-omap1/board-palmtt.c
*
* Modified from board-palmtt2.c
*
* Modified and amended for Palm Tungsten|T
* by Marek Vasut <marek.vasut@gmail.com>
*/
#include <linux/delay.h>
#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/notifier.h>
#include <linux/clk.h>
#include <linux/input.h>
#include <linux/interrupt.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
#include <linux/leds.h>
#include <linux/omapfb.h>
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
#include <linux/omap-dma.h>
#include <linux/platform_data/omap1_bl.h>
#include <linux/platform_data/leds-omap.h>
#include <linux/platform_data/keypad-omap.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include "tc.h"
#include "flash.h"
#include "mux.h"
#include "hardware.h"
#include "usb.h"
#include "common.h"
#define PALMTT_USBDETECT_GPIO 0
#define PALMTT_CABLE_GPIO 1
#define PALMTT_LED_GPIO 3
#define PALMTT_PENIRQ_GPIO 6
#define PALMTT_MMC_WP_GPIO 8
#define PALMTT_HDQ_GPIO 11
static const unsigned int palmtt_keymap[] = {
KEY(0, 0, KEY_ESC),
KEY(1, 0, KEY_SPACE),
KEY(2, 0, KEY_LEFTCTRL),
KEY(3, 0, KEY_TAB),
KEY(4, 0, KEY_ENTER),
KEY(0, 1, KEY_LEFT),
KEY(1, 1, KEY_DOWN),
KEY(2, 1, KEY_UP),
KEY(3, 1, KEY_RIGHT),
KEY(0, 2, KEY_SLEEP),
KEY(4, 2, KEY_Y),
};
static struct mtd_partition palmtt_partitions[] = {
{
.name = "write8k",
.offset = 0,
.size = SZ_8K,
.mask_flags = 0,
},
{
.name = "PalmOS-BootLoader(ro)",
.offset = SZ_8K,
.size = 7 * SZ_8K,
.mask_flags = MTD_WRITEABLE,
},
{
.name = "u-boot",
.offset = MTDPART_OFS_APPEND,
.size = 8 * SZ_8K,
.mask_flags = 0,
},
{
.name = "PalmOS-FS(ro)",
.offset = MTDPART_OFS_APPEND,
.size = 7 * SZ_1M + 4 * SZ_64K - 16 * SZ_8K,
.mask_flags = MTD_WRITEABLE,
},
{
.name = "u-boot(rez)",
.offset = MTDPART_OFS_APPEND,
.size = SZ_128K,
.mask_flags = 0
},
{
.name = "empty",
.offset = MTDPART_OFS_APPEND,
.size = MTDPART_SIZ_FULL,
.mask_flags = 0
}
};
static struct physmap_flash_data palmtt_flash_data = {
.width = 2,
.set_vpp = omap1_set_vpp,
.parts = palmtt_partitions,
.nr_parts = ARRAY_SIZE(palmtt_partitions),
};
static struct resource palmtt_flash_resource = {
.start = OMAP_CS0_PHYS,
.end = OMAP_CS0_PHYS + SZ_8M - 1,
.flags = IORESOURCE_MEM,
};
static struct platform_device palmtt_flash_device = {
.name = "physmap-flash",
.id = 0,
.dev = {
.platform_data = &palmtt_flash_data,
},
.num_resources = 1,
.resource = &palmtt_flash_resource,
};
static struct resource palmtt_kp_resources[] = {
[0] = {
.start = INT_KEYBOARD,
.end = INT_KEYBOARD,
.flags = IORESOURCE_IRQ,
},
};
static const struct matrix_keymap_data palmtt_keymap_data = {
.keymap = palmtt_keymap,
.keymap_size = ARRAY_SIZE(palmtt_keymap),
};
static struct omap_kp_platform_data palmtt_kp_data = {
.rows = 6,
.cols = 3,
.keymap_data = &palmtt_keymap_data,
};
static struct platform_device palmtt_kp_device = {
.name = "omap-keypad",
.id = -1,
.dev = {
.platform_data = &palmtt_kp_data,
},
.num_resources = ARRAY_SIZE(palmtt_kp_resources),
.resource = palmtt_kp_resources,
};
static struct platform_device palmtt_lcd_device = {
.name = "lcd_palmtt",
.id = -1,
};
static struct platform_device palmtt_spi_device = {
.name = "spi_palmtt",
.id = -1,
};
static struct omap_backlight_config palmtt_backlight_config = {
.default_intensity = 0xa0,
};
static struct platform_device palmtt_backlight_device = {
.name = "omap-bl",
.id = -1,
.dev = {
.platform_data= &palmtt_backlight_config,
},
};
static struct omap_led_config palmtt_led_config[] = {
{
.cdev = {
.name = "palmtt:led0",
},
.gpio = PALMTT_LED_GPIO,
},
};
static struct omap_led_platform_data palmtt_led_data = {
.nr_leds = ARRAY_SIZE(palmtt_led_config),
.leds = palmtt_led_config,
};
static struct platform_device palmtt_led_device = {
.name = "omap-led",
.id = -1,
.dev = {
.platform_data = &palmtt_led_data,
},
};
static struct platform_device *palmtt_devices[] __initdata = {
&palmtt_flash_device,
&palmtt_kp_device,
&palmtt_lcd_device,
&palmtt_spi_device,
&palmtt_backlight_device,
&palmtt_led_device,
};
static int palmtt_get_pendown_state(void)
{
return !gpio_get_value(6);
}
static const struct ads7846_platform_data palmtt_ts_info = {
.model = 7846,
.vref_delay_usecs = 100, /* internal, no capacitor */
.x_plate_ohms = 419,
.y_plate_ohms = 486,
.get_pendown_state = palmtt_get_pendown_state,
};
static struct spi_board_info __initdata palmtt_boardinfo[] = {
{
/* MicroWire (bus 2) CS0 has an ads7846e */
.modalias = "ads7846",
.platform_data = &palmtt_ts_info,
.max_speed_hz = 120000 /* max sample rate at 3V */
* 26 /* command + data + overhead */,
.bus_num = 2,
.chip_select = 0,
}
};
static struct omap_usb_config palmtt_usb_config __initdata = {
.register_dev = 1,
.hmc_mode = 0,
.pins[0] = 2,
};
static const struct omap_lcd_config palmtt_lcd_config __initconst = {
.ctrl_name = "internal",
};
static void __init omap_mpu_wdt_mode(int mode) {
if (mode)
omap_writew(0x8000, OMAP_WDT_TIMER_MODE);
else {
omap_writew(0x00f5, OMAP_WDT_TIMER_MODE);
omap_writew(0x00a0, OMAP_WDT_TIMER_MODE);
}
}
static void __init omap_palmtt_init(void)
{
/* mux pins for uarts */
omap_cfg_reg(UART1_TX);
omap_cfg_reg(UART1_RTS);
omap_cfg_reg(UART2_TX);
omap_cfg_reg(UART2_RTS);
omap_cfg_reg(UART3_TX);
omap_cfg_reg(UART3_RX);
omap_mpu_wdt_mode(0);
platform_add_devices(palmtt_devices, ARRAY_SIZE(palmtt_devices));
palmtt_boardinfo[0].irq = gpio_to_irq(6);
spi_register_board_info(palmtt_boardinfo,ARRAY_SIZE(palmtt_boardinfo));
omap_serial_init();
omap1_usb_init(&palmtt_usb_config);
omap_register_i2c_bus(1, 100, NULL, 0);
omapfb_set_lcd_config(&palmtt_lcd_config);
}
MACHINE_START(OMAP_PALMTT, "OMAP1510 based Palm Tungsten|T")
.atag_offset = 0x100,
.map_io = omap15xx_map_io,
.init_early = omap1_init_early,
.init_irq = omap1_init_irq,
.handle_irq = omap1_handle_irq,
.init_machine = omap_palmtt_init,
.init_late = omap1_init_late,
.init_time = omap1_timer_init,
.restart = omap1_restart,
MACHINE_END
// SPDX-License-Identifier: GPL-2.0-only
/*
* linux/arch/arm/mach-omap1/board-palmz71.c
*
* Modified from board-generic.c
*
* Support for the Palm Zire71 PDA.
*
* Original version : Laurent Gonzalez
*
* Modified for zire71 : Marek Vasut
*/
#include <linux/delay.h>
#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/notifier.h>
#include <linux/clk.h>
#include <linux/irq.h>
#include <linux/input.h>
#include <linux/interrupt.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
#include <linux/omapfb.h>
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
#include <linux/platform_data/omap1_bl.h>
#include <linux/platform_data/keypad-omap.h>
#include <linux/omap-dma.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include "tc.h"
#include "flash.h"
#include "mux.h"
#include "hardware.h"
#include "usb.h"
#include "common.h"
#define PALMZ71_USBDETECT_GPIO 0
#define PALMZ71_PENIRQ_GPIO 6
#define PALMZ71_MMC_WP_GPIO 8
#define PALMZ71_HDQ_GPIO 11
#define PALMZ71_HOTSYNC_GPIO OMAP_MPUIO(1)
#define PALMZ71_CABLE_GPIO OMAP_MPUIO(2)
#define PALMZ71_SLIDER_GPIO OMAP_MPUIO(3)
#define PALMZ71_MMC_IN_GPIO OMAP_MPUIO(4)
static const unsigned int palmz71_keymap[] = {
KEY(0, 0, KEY_F1),
KEY(1, 0, KEY_F2),
KEY(2, 0, KEY_F3),
KEY(3, 0, KEY_F4),
KEY(4, 0, KEY_POWER),
KEY(0, 1, KEY_LEFT),
KEY(1, 1, KEY_DOWN),
KEY(2, 1, KEY_UP),
KEY(3, 1, KEY_RIGHT),
KEY(4, 1, KEY_ENTER),
KEY(0, 2, KEY_CAMERA),
};
static const struct matrix_keymap_data palmz71_keymap_data = {
.keymap = palmz71_keymap,
.keymap_size = ARRAY_SIZE(palmz71_keymap),
};
static struct omap_kp_platform_data palmz71_kp_data = {
.rows = 8,
.cols = 8,
.keymap_data = &palmz71_keymap_data,
.rep = true,
.delay = 80,
};
static struct resource palmz71_kp_resources[] = {
[0] = {
.start = INT_KEYBOARD,
.end = INT_KEYBOARD,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device palmz71_kp_device = {
.name = "omap-keypad",
.id = -1,
.dev = {
.platform_data = &palmz71_kp_data,
},
.num_resources = ARRAY_SIZE(palmz71_kp_resources),
.resource = palmz71_kp_resources,
};
static struct mtd_partition palmz71_rom_partitions[] = {
/* PalmOS "Small ROM", contains the bootloader and the debugger */
{
.name = "smallrom",
.offset = 0,
.size = 0xa000,
.mask_flags = MTD_WRITEABLE,
},
/* PalmOS "Big ROM", a filesystem with all the OS code and data */
{
.name = "bigrom",
.offset = SZ_128K,
/*
* 0x5f0000 bytes big in the multi-language ("EFIGS") version,
* 0x7b0000 bytes in the English-only ("enUS") version.
*/
.size = 0x7b0000,
.mask_flags = MTD_WRITEABLE,
},
};
static struct physmap_flash_data palmz71_rom_data = {
.width = 2,
.set_vpp = omap1_set_vpp,
.parts = palmz71_rom_partitions,
.nr_parts = ARRAY_SIZE(palmz71_rom_partitions),
};
static struct resource palmz71_rom_resource = {
.start = OMAP_CS0_PHYS,
.end = OMAP_CS0_PHYS + SZ_8M - 1,
.flags = IORESOURCE_MEM,
};
static struct platform_device palmz71_rom_device = {
.name = "physmap-flash",
.id = -1,
.dev = {
.platform_data = &palmz71_rom_data,
},
.num_resources = 1,
.resource = &palmz71_rom_resource,
};
static struct platform_device palmz71_lcd_device = {
.name = "lcd_palmz71",
.id = -1,
};
static struct platform_device palmz71_spi_device = {
.name = "spi_palmz71",
.id = -1,
};
static struct omap_backlight_config palmz71_backlight_config = {
.default_intensity = 0xa0,
};
static struct platform_device palmz71_backlight_device = {
.name = "omap-bl",
.id = -1,
.dev = {
.platform_data = &palmz71_backlight_config,
},
};
static struct platform_device *devices[] __initdata = {
&palmz71_rom_device,
&palmz71_kp_device,
&palmz71_lcd_device,
&palmz71_spi_device,
&palmz71_backlight_device,
};
static int
palmz71_get_pendown_state(void)
{
return !gpio_get_value(PALMZ71_PENIRQ_GPIO);
}
static const struct ads7846_platform_data palmz71_ts_info = {
.model = 7846,
.vref_delay_usecs = 100, /* internal, no capacitor */
.x_plate_ohms = 419,
.y_plate_ohms = 486,
.get_pendown_state = palmz71_get_pendown_state,
};
static struct spi_board_info __initdata palmz71_boardinfo[] = { {
/* MicroWire (bus 2) CS0 has an ads7846e */
.modalias = "ads7846",
.platform_data = &palmz71_ts_info,
.max_speed_hz = 120000 /* max sample rate at 3V */
* 26 /* command + data + overhead */,
.bus_num = 2,
.chip_select = 0,
} };
static struct omap_usb_config palmz71_usb_config __initdata = {
.register_dev = 1, /* Mini-B only receptacle */
.hmc_mode = 0,
.pins[0] = 2,
};
static const struct omap_lcd_config palmz71_lcd_config __initconst = {
.ctrl_name = "internal",
};
static irqreturn_t
palmz71_powercable(int irq, void *dev_id)
{
if (gpio_get_value(PALMZ71_USBDETECT_GPIO)) {
printk(KERN_INFO "PM: Power cable connected\n");
irq_set_irq_type(gpio_to_irq(PALMZ71_USBDETECT_GPIO),
IRQ_TYPE_EDGE_FALLING);
} else {
printk(KERN_INFO "PM: Power cable disconnected\n");
irq_set_irq_type(gpio_to_irq(PALMZ71_USBDETECT_GPIO),
IRQ_TYPE_EDGE_RISING);
}
return IRQ_HANDLED;
}
static void __init
omap_mpu_wdt_mode(int mode)
{
if (mode)
omap_writew(0x8000, OMAP_WDT_TIMER_MODE);
else {
omap_writew(0x00f5, OMAP_WDT_TIMER_MODE);
omap_writew(0x00a0, OMAP_WDT_TIMER_MODE);
}
}
static void __init
palmz71_gpio_setup(int early)
{
if (early) {
/* Only set GPIO1 so we have a working serial */
gpio_direction_output(1, 1);
} else {
/* Set MMC/SD host WP pin as input */
if (gpio_request(PALMZ71_MMC_WP_GPIO, "MMC WP") < 0) {
printk(KERN_ERR "Could not reserve WP GPIO!\n");
return;
}
gpio_direction_input(PALMZ71_MMC_WP_GPIO);
/* Monitor the Power-cable-connected signal */
if (gpio_request(PALMZ71_USBDETECT_GPIO, "USB detect") < 0) {
printk(KERN_ERR
"Could not reserve cable signal GPIO!\n");
return;
}
gpio_direction_input(PALMZ71_USBDETECT_GPIO);
if (request_irq(gpio_to_irq(PALMZ71_USBDETECT_GPIO),
palmz71_powercable, 0, "palmz71-cable", NULL))
printk(KERN_ERR
"IRQ request for power cable failed!\n");
palmz71_powercable(gpio_to_irq(PALMZ71_USBDETECT_GPIO), NULL);
}
}
static void __init
omap_palmz71_init(void)
{
/* mux pins for uarts */
omap_cfg_reg(UART1_TX);
omap_cfg_reg(UART1_RTS);
omap_cfg_reg(UART2_TX);
omap_cfg_reg(UART2_RTS);
omap_cfg_reg(UART3_TX);
omap_cfg_reg(UART3_RX);
palmz71_gpio_setup(1);
omap_mpu_wdt_mode(0);
platform_add_devices(devices, ARRAY_SIZE(devices));
palmz71_boardinfo[0].irq = gpio_to_irq(PALMZ71_PENIRQ_GPIO);
spi_register_board_info(palmz71_boardinfo,
ARRAY_SIZE(palmz71_boardinfo));
omap1_usb_init(&palmz71_usb_config);
omap_serial_init();
omap_register_i2c_bus(1, 100, NULL, 0);
palmz71_gpio_setup(0);
omapfb_set_lcd_config(&palmz71_lcd_config);
}
MACHINE_START(OMAP_PALMZ71, "OMAP310 based Palm Zire71")
.atag_offset = 0x100,
.map_io = omap15xx_map_io,
.init_early = omap1_init_early,
.init_irq = omap1_init_irq,
.handle_irq = omap1_handle_irq,
.init_machine = omap_palmz71_init,
.init_late = omap1_init_late,
.init_time = omap1_timer_init,
.restart = omap1_restart,
MACHINE_END
// SPDX-License-Identifier: GPL-2.0-only
/*
* linux/arch/arm/mach-omap1/board-perseus2.c
*
* Modified from board-generic.c
*
* Original OMAP730 support by Jean Pihet <j-pihet@ti.com>
* Updated for 2.6 by Kevin Hilman <kjh@hilman.org>
*/
#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/platnand.h>
#include <linux/mtd/physmap.h>
#include <linux/input.h>
#include <linux/smc91x.h>
#include <linux/omapfb.h>
#include <linux/platform_data/keypad-omap.h>
#include <linux/soc/ti/omap1-io.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include "tc.h"
#include "mux.h"
#include "flash.h"
#include "hardware.h"
#include "iomap.h"
#include "common.h"
#include "fpga.h"
static const unsigned int p2_keymap[] = {
KEY(0, 0, KEY_UP),
KEY(1, 0, KEY_RIGHT),
KEY(2, 0, KEY_LEFT),
KEY(3, 0, KEY_DOWN),
KEY(4, 0, KEY_ENTER),
KEY(0, 1, KEY_F10),
KEY(1, 1, KEY_SEND),
KEY(2, 1, KEY_END),
KEY(3, 1, KEY_VOLUMEDOWN),
KEY(4, 1, KEY_VOLUMEUP),
KEY(5, 1, KEY_RECORD),
KEY(0, 2, KEY_F9),
KEY(1, 2, KEY_3),
KEY(2, 2, KEY_6),
KEY(3, 2, KEY_9),
KEY(4, 2, KEY_KPDOT),
KEY(0, 3, KEY_BACK),
KEY(1, 3, KEY_2),
KEY(2, 3, KEY_5),
KEY(3, 3, KEY_8),
KEY(4, 3, KEY_0),
KEY(5, 3, KEY_KPSLASH),
KEY(0, 4, KEY_HOME),
KEY(1, 4, KEY_1),
KEY(2, 4, KEY_4),
KEY(3, 4, KEY_7),
KEY(4, 4, KEY_KPASTERISK),
KEY(5, 4, KEY_POWER),
};
static struct smc91x_platdata smc91x_info = {
.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
.leda = RPC_LED_100_10,
.ledb = RPC_LED_TX_RX,
};
static struct resource smc91x_resources[] = {
[0] = {
.start = H2P2_DBG_FPGA_ETHR_START, /* Physical */
.end = H2P2_DBG_FPGA_ETHR_START + 0xf,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = INT_7XX_MPU_EXT_NIRQ,
.end = 0,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
},
};
static struct mtd_partition nor_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
{
.name = "bootloader",
.offset = 0,
.size = SZ_128K,
.mask_flags = MTD_WRITEABLE, /* force read-only */
},
/* bootloader params in the next sector */
{
.name = "params",
.offset = MTDPART_OFS_APPEND,
.size = SZ_128K,
.mask_flags = 0,
},
/* kernel */
{
.name = "kernel",
.offset = MTDPART_OFS_APPEND,
.size = SZ_2M,
.mask_flags = 0
},
/* rest of flash is a file system */
{
.name = "rootfs",
.offset = MTDPART_OFS_APPEND,
.size = MTDPART_SIZ_FULL,
.mask_flags = 0
},
};
static struct physmap_flash_data nor_data = {
.width = 2,
.set_vpp = omap1_set_vpp,
.parts = nor_partitions,
.nr_parts = ARRAY_SIZE(nor_partitions),
};
static struct resource nor_resource = {
.start = OMAP_CS0_PHYS,
.end = OMAP_CS0_PHYS + SZ_32M - 1,
.flags = IORESOURCE_MEM,
};
static struct platform_device nor_device = {
.name = "physmap-flash",
.id = 0,
.dev = {
.platform_data = &nor_data,
},
.num_resources = 1,
.resource = &nor_resource,
};
#define P2_NAND_RB_GPIO_PIN 62
static int nand_dev_ready(struct nand_chip *chip)
{
return gpio_get_value(P2_NAND_RB_GPIO_PIN);
}
static struct platform_nand_data nand_data = {
.chip = {
.nr_chips = 1,
.chip_offset = 0,
.options = NAND_SAMSUNG_LP_OPTIONS,
},
.ctrl = {
.cmd_ctrl = omap1_nand_cmd_ctl,
.dev_ready = nand_dev_ready,
},
};
static struct resource nand_resource = {
.start = OMAP_CS3_PHYS,
.end = OMAP_CS3_PHYS + SZ_4K - 1,
.flags = IORESOURCE_MEM,
};
static struct platform_device nand_device = {
.name = "gen_nand",
.id = 0,
.dev = {
.platform_data = &nand_data,
},
.num_resources = 1,
.resource = &nand_resource,
};
static struct platform_device smc91x_device = {
.name = "smc91x",
.id = 0,
.dev = {
.platform_data = &smc91x_info,
},
.num_resources = ARRAY_SIZE(smc91x_resources),
.resource = smc91x_resources,
};
static struct resource kp_resources[] = {
[0] = {
.start = INT_7XX_MPUIO_KEYPAD,
.end = INT_7XX_MPUIO_KEYPAD,
.flags = IORESOURCE_IRQ,
},
};
static const struct matrix_keymap_data p2_keymap_data = {
.keymap = p2_keymap,
.keymap_size = ARRAY_SIZE(p2_keymap),
};
static struct omap_kp_platform_data kp_data = {
.rows = 8,
.cols = 8,
.keymap_data = &p2_keymap_data,
.delay = 4,
.dbounce = true,
};
static struct platform_device kp_device = {
.name = "omap-keypad",
.id = -1,
.dev = {
.platform_data = &kp_data,
},
.num_resources = ARRAY_SIZE(kp_resources),
.resource = kp_resources,
};
static struct platform_device *devices[] __initdata = {
&nor_device,
&nand_device,
&smc91x_device,
&kp_device,
};
static const struct omap_lcd_config perseus2_lcd_config __initconst = {
.ctrl_name = "internal",
};
static void __init perseus2_init_smc91x(void)
{
__raw_writeb(1, H2P2_DBG_FPGA_LAN_RESET);
mdelay(50);
__raw_writeb(__raw_readb(H2P2_DBG_FPGA_LAN_RESET) & ~1,
H2P2_DBG_FPGA_LAN_RESET);
mdelay(50);
}
static void __init omap_perseus2_init(void)
{
/* Early, board-dependent init */
/*
* Hold GSM Reset until needed
*/
omap_writew(omap_readw(OMAP7XX_DSP_M_CTL) & ~1, OMAP7XX_DSP_M_CTL);
/*
* UARTs -> done automagically by 8250 driver
*/
/*
* CSx timings, GPIO Mux ... setup
*/
/* Flash: CS0 timings setup */
omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_0);
omap_writel(0x00000088, OMAP7XX_FLASH_ACFG_0);
/*
* Ethernet support through the debug board
* CS1 timings setup
*/
omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_1);
omap_writel(0x00000000, OMAP7XX_FLASH_ACFG_1);
/*
* Configure MPU_EXT_NIRQ IO in IO_CONF9 register,
* It is used as the Ethernet controller interrupt
*/
omap_writel(omap_readl(OMAP7XX_IO_CONF_9) & 0x1FFFFFFF,
OMAP7XX_IO_CONF_9);
perseus2_init_smc91x();
BUG_ON(gpio_request(P2_NAND_RB_GPIO_PIN, "NAND ready") < 0);
gpio_direction_input(P2_NAND_RB_GPIO_PIN);
omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
/* Mux pins for keypad */
omap_cfg_reg(E2_7XX_KBR0);
omap_cfg_reg(J7_7XX_KBR1);
omap_cfg_reg(E1_7XX_KBR2);
omap_cfg_reg(F3_7XX_KBR3);
omap_cfg_reg(D2_7XX_KBR4);
omap_cfg_reg(C2_7XX_KBC0);
omap_cfg_reg(D3_7XX_KBC1);
omap_cfg_reg(E4_7XX_KBC2);
omap_cfg_reg(F4_7XX_KBC3);
omap_cfg_reg(E3_7XX_KBC4);
if (IS_ENABLED(CONFIG_SPI_OMAP_UWIRE)) {
/* configure pins: MPU_UW_nSCS1, MPU_UW_SDO, MPU_UW_SCLK */
int val = omap_readl(OMAP7XX_IO_CONF_9) & ~0x00EEE000;
omap_writel(val | 0x00AAA000, OMAP7XX_IO_CONF_9);
}
platform_add_devices(devices, ARRAY_SIZE(devices));
omap_serial_init();
omap_register_i2c_bus(1, 100, NULL, 0);
omapfb_set_lcd_config(&perseus2_lcd_config);
}
/* Only FPGA needs to be mapped here. All others are done with ioremap */
static struct map_desc omap_perseus2_io_desc[] __initdata = {
{
.virtual = H2P2_DBG_FPGA_BASE,
.pfn = __phys_to_pfn(H2P2_DBG_FPGA_START),
.length = H2P2_DBG_FPGA_SIZE,
.type = MT_DEVICE
}
};
static void __init omap_perseus2_map_io(void)
{
omap7xx_map_io();
iotable_init(omap_perseus2_io_desc,
ARRAY_SIZE(omap_perseus2_io_desc));
}
MACHINE_START(OMAP_PERSEUS2, "OMAP730 Perseus2")
/* Maintainer: Kevin Hilman <kjh@hilman.org> */
.atag_offset = 0x100,
.map_io = omap_perseus2_map_io,
.init_early = omap1_init_early,
.init_irq = omap1_init_irq,
.handle_irq = omap1_handle_irq,
.init_machine = omap_perseus2_init,
.init_late = omap1_init_late,
.init_time = omap1_timer_init,
.restart = omap1_restart,
MACHINE_END
// SPDX-License-Identifier: GPL-2.0-only
/*
* linux/arch/arm/mach-omap1/fpga.c
*
* Interrupt handler for OMAP-1510 Innovator FPGA
*
* Copyright (C) 2001 RidgeRun, Inc.
* Author: Greg Lonnon <glonnon@ridgerun.com>
*
* Copyright (C) 2002 MontaVista Software, Inc.
*
* Separated FPGA interrupts from innovator1510.c and cleaned up for 2.6
* Copyright (C) 2004 Nokia Corporation by Tony Lindrgen <tony@atomide.com>
*/
#include <linux/types.h>
#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/device.h>
#include <linux/errno.h>
#include <linux/io.h>
#include <asm/irq.h>
#include <asm/mach/irq.h>
#include "hardware.h"
#include "iomap.h"
#include "common.h"
#include "fpga.h"
static void fpga_mask_irq(struct irq_data *d)
{
unsigned int irq = d->irq - OMAP_FPGA_IRQ_BASE;
if (irq < 8)
__raw_writeb((__raw_readb(OMAP1510_FPGA_IMR_LO)
& ~(1 << irq)), OMAP1510_FPGA_IMR_LO);
else if (irq < 16)
__raw_writeb((__raw_readb(OMAP1510_FPGA_IMR_HI)
& ~(1 << (irq - 8))), OMAP1510_FPGA_IMR_HI);
else
__raw_writeb((__raw_readb(INNOVATOR_FPGA_IMR2)
& ~(1 << (irq - 16))), INNOVATOR_FPGA_IMR2);
}
static inline u32 get_fpga_unmasked_irqs(void)
{
return
((__raw_readb(OMAP1510_FPGA_ISR_LO) &
__raw_readb(OMAP1510_FPGA_IMR_LO))) |
((__raw_readb(OMAP1510_FPGA_ISR_HI) &
__raw_readb(OMAP1510_FPGA_IMR_HI)) << 8) |
((__raw_readb(INNOVATOR_FPGA_ISR2) &
__raw_readb(INNOVATOR_FPGA_IMR2)) << 16);
}
static void fpga_ack_irq(struct irq_data *d)
{
/* Don't need to explicitly ACK FPGA interrupts */
}
static void fpga_unmask_irq(struct irq_data *d)
{
unsigned int irq = d->irq - OMAP_FPGA_IRQ_BASE;
if (irq < 8)
__raw_writeb((__raw_readb(OMAP1510_FPGA_IMR_LO) | (1 << irq)),
OMAP1510_FPGA_IMR_LO);
else if (irq < 16)
__raw_writeb((__raw_readb(OMAP1510_FPGA_IMR_HI)
| (1 << (irq - 8))), OMAP1510_FPGA_IMR_HI);
else
__raw_writeb((__raw_readb(INNOVATOR_FPGA_IMR2)
| (1 << (irq - 16))), INNOVATOR_FPGA_IMR2);
}
static void fpga_mask_ack_irq(struct irq_data *d)
{
fpga_mask_irq(d);
fpga_ack_irq(d);
}
static void innovator_fpga_IRQ_demux(struct irq_desc *desc)
{
u32 stat;
int fpga_irq;
stat = get_fpga_unmasked_irqs();
if (!stat)
return;
for (fpga_irq = OMAP_FPGA_IRQ_BASE;
(fpga_irq < OMAP_FPGA_IRQ_END) && stat;
fpga_irq++, stat >>= 1) {
if (stat & 1) {
generic_handle_irq(fpga_irq);
}
}
}
static struct irq_chip omap_fpga_irq_ack = {
.name = "FPGA-ack",
.irq_ack = fpga_mask_ack_irq,
.irq_mask = fpga_mask_irq,
.irq_unmask = fpga_unmask_irq,
};
static struct irq_chip omap_fpga_irq = {
.name = "FPGA",
.irq_ack = fpga_ack_irq,
.irq_mask = fpga_mask_irq,
.irq_unmask = fpga_unmask_irq,
};
/*
* All of the FPGA interrupt request inputs except for the touchscreen are
* edge-sensitive; the touchscreen is level-sensitive. The edge-sensitive
* interrupts are acknowledged as a side-effect of reading the interrupt
* status register from the FPGA. The edge-sensitive interrupt inputs
* cause a problem with level interrupt requests, such as Ethernet. The
* problem occurs when a level interrupt request is asserted while its
* interrupt input is masked in the FPGA, which results in a missed
* interrupt.
*
* In an attempt to workaround the problem with missed interrupts, the
* mask_ack routine for all of the FPGA interrupts has been changed from
* fpga_mask_ack_irq() to fpga_ack_irq() so that the specific FPGA interrupt
* being serviced is left unmasked. We can do this because the FPGA cascade
* interrupt is run with all interrupts masked.
*
* Limited testing indicates that this workaround appears to be effective
* for the smc9194 Ethernet driver used on the Innovator. It should work
* on other FPGA interrupts as well, but any drivers that explicitly mask
* interrupts at the interrupt controller via disable_irq/enable_irq
* could pose a problem.
*/
void omap1510_fpga_init_irq(void)
{
int i, res;
__raw_writeb(0, OMAP1510_FPGA_IMR_LO);
__raw_writeb(0, OMAP1510_FPGA_IMR_HI);
__raw_writeb(0, INNOVATOR_FPGA_IMR2);
for (i = OMAP_FPGA_IRQ_BASE; i < OMAP_FPGA_IRQ_END; i++) {
if (i == OMAP1510_INT_FPGA_TS) {
/*
* The touchscreen interrupt is level-sensitive, so
* we'll use the regular mask_ack routine for it.
*/
irq_set_chip(i, &omap_fpga_irq_ack);
}
else {
/*
* All FPGA interrupts except the touchscreen are
* edge-sensitive, so we won't mask them.
*/
irq_set_chip(i, &omap_fpga_irq);
}
irq_set_handler(i, handle_edge_irq);
irq_clear_status_flags(i, IRQ_NOREQUEST);
}
/*
* The FPGA interrupt line is connected to GPIO13. Claim this pin for
* the ARM.
*
* NOTE: For general GPIO/MPUIO access and interrupts, please see
* gpio.[ch]
*/
res = gpio_request(13, "FPGA irq");
if (res) {
pr_err("%s failed to get gpio\n", __func__);
return;
}
gpio_direction_input(13);
irq_set_irq_type(gpio_to_irq(13), IRQ_TYPE_EDGE_RISING);
irq_set_chained_handler(OMAP1510_INT_FPGA, innovator_fpga_IRQ_demux);
}
/* SPDX-License-Identifier: GPL-2.0-only */
/*
* Interrupt handler for OMAP-1510 FPGA
*
* Copyright (C) 2001 RidgeRun, Inc.
* Author: Greg Lonnon <glonnon@ridgerun.com>
*
* Copyright (C) 2002 MontaVista Software, Inc.
*
* Separated FPGA interrupts from innovator1510.c and cleaned up for 2.6
* Copyright (C) 2004 Nokia Corporation by Tony Lindrgen <tony@atomide.com>
*/
#ifndef __ASM_ARCH_OMAP_FPGA_H
#define __ASM_ARCH_OMAP_FPGA_H
/*
* ---------------------------------------------------------------------------
* H2/P2 Debug board FPGA
* ---------------------------------------------------------------------------
*/
/* maps in the FPGA registers and the ETHR registers */
#define H2P2_DBG_FPGA_BASE 0xE8000000 /* VA */
#define H2P2_DBG_FPGA_SIZE SZ_4K /* SIZE */
#define H2P2_DBG_FPGA_START 0x04000000 /* PA */
#define H2P2_DBG_FPGA_ETHR_START (H2P2_DBG_FPGA_START + 0x300)
#define H2P2_DBG_FPGA_FPGA_REV IOMEM(H2P2_DBG_FPGA_BASE + 0x10) /* FPGA Revision */
#define H2P2_DBG_FPGA_BOARD_REV IOMEM(H2P2_DBG_FPGA_BASE + 0x12) /* Board Revision */
#define H2P2_DBG_FPGA_GPIO IOMEM(H2P2_DBG_FPGA_BASE + 0x14) /* GPIO outputs */
#define H2P2_DBG_FPGA_LEDS IOMEM(H2P2_DBG_FPGA_BASE + 0x16) /* LEDs outputs */
#define H2P2_DBG_FPGA_MISC_INPUTS IOMEM(H2P2_DBG_FPGA_BASE + 0x18) /* Misc inputs */
#define H2P2_DBG_FPGA_LAN_STATUS IOMEM(H2P2_DBG_FPGA_BASE + 0x1A) /* LAN Status line */
#define H2P2_DBG_FPGA_LAN_RESET IOMEM(H2P2_DBG_FPGA_BASE + 0x1C) /* LAN Reset line */
/* LEDs definition on debug board (16 LEDs, all physically green) */
#define H2P2_DBG_FPGA_LED_GREEN (1 << 15)
#define H2P2_DBG_FPGA_LED_AMBER (1 << 14)
#define H2P2_DBG_FPGA_LED_RED (1 << 13)
#define H2P2_DBG_FPGA_LED_BLUE (1 << 12)
/* cpu0 load-meter LEDs */
#define H2P2_DBG_FPGA_LOAD_METER (1 << 0) // A bit of fun on our board ...
#define H2P2_DBG_FPGA_LOAD_METER_SIZE 11
#define H2P2_DBG_FPGA_LOAD_METER_MASK ((1 << H2P2_DBG_FPGA_LOAD_METER_SIZE) - 1)
#define H2P2_DBG_FPGA_P2_LED_TIMER (1 << 0)
#define H2P2_DBG_FPGA_P2_LED_IDLE (1 << 1)
#endif
// SPDX-License-Identifier: GPL-2.0-only
/*
* OMAP7xx specific gpio init
*
* Copyright (C) 2010 Texas Instruments Incorporated - https://www.ti.com/
*
* Author:
* Charulatha V <charu@ti.com>
*/
#include <linux/gpio.h>
#include <linux/platform_data/gpio-omap.h>
#include "irqs.h"
#include "soc.h"
#define OMAP7XX_GPIO1_BASE 0xfffbc000
#define OMAP7XX_GPIO2_BASE 0xfffbc800
#define OMAP7XX_GPIO3_BASE 0xfffbd000
#define OMAP7XX_GPIO4_BASE 0xfffbd800
#define OMAP7XX_GPIO5_BASE 0xfffbe000
#define OMAP7XX_GPIO6_BASE 0xfffbe800
#define OMAP1_MPUIO_VBASE OMAP1_MPUIO_BASE
/* mpu gpio */
static struct resource omap7xx_mpu_gpio_resources[] = {
{
.start = OMAP1_MPUIO_VBASE,
.end = OMAP1_MPUIO_VBASE + SZ_2K - 1,
.flags = IORESOURCE_MEM,
},
{
.start = INT_7XX_MPUIO,
.flags = IORESOURCE_IRQ,
},
};
static struct omap_gpio_reg_offs omap7xx_mpuio_regs = {
.revision = USHRT_MAX,
.direction = OMAP_MPUIO_IO_CNTL / 2,
.datain = OMAP_MPUIO_INPUT_LATCH / 2,
.dataout = OMAP_MPUIO_OUTPUT / 2,
.irqstatus = OMAP_MPUIO_GPIO_INT / 2,
.irqenable = OMAP_MPUIO_GPIO_MASKIT / 2,
.irqenable_inv = true,
.irqctrl = OMAP_MPUIO_GPIO_INT_EDGE >> 1,
};
static struct omap_gpio_platform_data omap7xx_mpu_gpio_config = {
.is_mpuio = true,
.bank_width = 16,
.bank_stride = 2,
.regs = &omap7xx_mpuio_regs,
};
static struct platform_device omap7xx_mpu_gpio = {
.name = "omap_gpio",
.id = 0,
.dev = {
.platform_data = &omap7xx_mpu_gpio_config,
},
.num_resources = ARRAY_SIZE(omap7xx_mpu_gpio_resources),
.resource = omap7xx_mpu_gpio_resources,
};
/* gpio1 */
static struct resource omap7xx_gpio1_resources[] = {
{
.start = OMAP7XX_GPIO1_BASE,
.end = OMAP7XX_GPIO1_BASE + SZ_2K - 1,
.flags = IORESOURCE_MEM,
},
{
.start = INT_7XX_GPIO_BANK1,
.flags = IORESOURCE_IRQ,
},
};
static struct omap_gpio_reg_offs omap7xx_gpio_regs = {
.revision = USHRT_MAX,
.direction = OMAP7XX_GPIO_DIR_CONTROL,
.datain = OMAP7XX_GPIO_DATA_INPUT,
.dataout = OMAP7XX_GPIO_DATA_OUTPUT,
.irqstatus = OMAP7XX_GPIO_INT_STATUS,
.irqenable = OMAP7XX_GPIO_INT_MASK,
.irqenable_inv = true,
.irqctrl = OMAP7XX_GPIO_INT_CONTROL,
};
static struct omap_gpio_platform_data omap7xx_gpio1_config = {
.bank_width = 32,
.regs = &omap7xx_gpio_regs,
};
static struct platform_device omap7xx_gpio1 = {
.name = "omap_gpio",
.id = 1,
.dev = {
.platform_data = &omap7xx_gpio1_config,
},
.num_resources = ARRAY_SIZE(omap7xx_gpio1_resources),
.resource = omap7xx_gpio1_resources,
};
/* gpio2 */
static struct resource omap7xx_gpio2_resources[] = {
{
.start = OMAP7XX_GPIO2_BASE,
.end = OMAP7XX_GPIO2_BASE + SZ_2K - 1,
.flags = IORESOURCE_MEM,
},
{
.start = INT_7XX_GPIO_BANK2,
.flags = IORESOURCE_IRQ,
},
};
static struct omap_gpio_platform_data omap7xx_gpio2_config = {
.bank_width = 32,
.regs = &omap7xx_gpio_regs,
};
static struct platform_device omap7xx_gpio2 = {
.name = "omap_gpio",
.id = 2,
.dev = {
.platform_data = &omap7xx_gpio2_config,
},
.num_resources = ARRAY_SIZE(omap7xx_gpio2_resources),
.resource = omap7xx_gpio2_resources,
};
/* gpio3 */
static struct resource omap7xx_gpio3_resources[] = {
{
.start = OMAP7XX_GPIO3_BASE,
.end = OMAP7XX_GPIO3_BASE + SZ_2K - 1,
.flags = IORESOURCE_MEM,
},
{
.start = INT_7XX_GPIO_BANK3,
.flags = IORESOURCE_IRQ,
},
};
static struct omap_gpio_platform_data omap7xx_gpio3_config = {
.bank_width = 32,
.regs = &omap7xx_gpio_regs,
};
static struct platform_device omap7xx_gpio3 = {
.name = "omap_gpio",
.id = 3,
.dev = {
.platform_data = &omap7xx_gpio3_config,
},
.num_resources = ARRAY_SIZE(omap7xx_gpio3_resources),
.resource = omap7xx_gpio3_resources,
};
/* gpio4 */
static struct resource omap7xx_gpio4_resources[] = {
{
.start = OMAP7XX_GPIO4_BASE,
.end = OMAP7XX_GPIO4_BASE + SZ_2K - 1,
.flags = IORESOURCE_MEM,
},
{
.start = INT_7XX_GPIO_BANK4,
.flags = IORESOURCE_IRQ,
},
};
static struct omap_gpio_platform_data omap7xx_gpio4_config = {
.bank_width = 32,
.regs = &omap7xx_gpio_regs,
};
static struct platform_device omap7xx_gpio4 = {
.name = "omap_gpio",
.id = 4,
.dev = {
.platform_data = &omap7xx_gpio4_config,
},
.num_resources = ARRAY_SIZE(omap7xx_gpio4_resources),
.resource = omap7xx_gpio4_resources,
};
/* gpio5 */
static struct resource omap7xx_gpio5_resources[] = {
{
.start = OMAP7XX_GPIO5_BASE,
.end = OMAP7XX_GPIO5_BASE + SZ_2K - 1,
.flags = IORESOURCE_MEM,
},
{
.start = INT_7XX_GPIO_BANK5,
.flags = IORESOURCE_IRQ,
},
};
static struct omap_gpio_platform_data omap7xx_gpio5_config = {
.bank_width = 32,
.regs = &omap7xx_gpio_regs,
};
static struct platform_device omap7xx_gpio5 = {
.name = "omap_gpio",
.id = 5,
.dev = {
.platform_data = &omap7xx_gpio5_config,
},
.num_resources = ARRAY_SIZE(omap7xx_gpio5_resources),
.resource = omap7xx_gpio5_resources,
};
/* gpio6 */
static struct resource omap7xx_gpio6_resources[] = {
{
.start = OMAP7XX_GPIO6_BASE,
.end = OMAP7XX_GPIO6_BASE + SZ_2K - 1,
.flags = IORESOURCE_MEM,
},
{
.start = INT_7XX_GPIO_BANK6,
.flags = IORESOURCE_IRQ,
},
};
static struct omap_gpio_platform_data omap7xx_gpio6_config = {
.bank_width = 32,
.regs = &omap7xx_gpio_regs,
};
static struct platform_device omap7xx_gpio6 = {
.name = "omap_gpio",
.id = 6,
.dev = {
.platform_data = &omap7xx_gpio6_config,
},
.num_resources = ARRAY_SIZE(omap7xx_gpio6_resources),
.resource = omap7xx_gpio6_resources,
};
static struct platform_device *omap7xx_gpio_dev[] __initdata = {
&omap7xx_mpu_gpio,
&omap7xx_gpio1,
&omap7xx_gpio2,
&omap7xx_gpio3,
&omap7xx_gpio4,
&omap7xx_gpio5,
&omap7xx_gpio6,
};
/*
* omap7xx_gpio_init needs to be done before
* machine_init functions access gpio APIs.
* Hence omap7xx_gpio_init is a postcore_initcall.
*/
static int __init omap7xx_gpio_init(void)
{
int i;
if (!cpu_is_omap7xx())
return -EINVAL;
for (i = 0; i < ARRAY_SIZE(omap7xx_gpio_dev); i++)
platform_device_register(omap7xx_gpio_dev[i]);
return 0;
}
postcore_initcall(omap7xx_gpio_init);
...@@ -874,7 +874,7 @@ config I2C_OCORES ...@@ -874,7 +874,7 @@ config I2C_OCORES
config I2C_OMAP config I2C_OMAP
tristate "OMAP I2C adapter" tristate "OMAP I2C adapter"
depends on ARCH_OMAP || ARCH_K3 || COMPILE_TEST depends on ARCH_OMAP || ARCH_K3 || COMPILE_TEST
default y if MACH_OMAP_H3 || MACH_OMAP_OSK default MACH_OMAP_OSK
help help
If you say yes to this option, support will be included for the If you say yes to this option, support will be included for the
I2C interface on the Texas Instruments OMAP1/2 family of processors. I2C interface on the Texas Instruments OMAP1/2 family of processors.
......
...@@ -1514,7 +1514,7 @@ config TPS6105X ...@@ -1514,7 +1514,7 @@ config TPS6105X
config TPS65010 config TPS65010
tristate "TI TPS6501x Power Management chips" tristate "TI TPS6501x Power Management chips"
depends on I2C && GPIOLIB depends on I2C && GPIOLIB
default y if MACH_OMAP_H2 || MACH_OMAP_H3 || MACH_OMAP_OSK default MACH_OMAP_OSK
help help
If you say yes here you get support for the TPS6501x series of If you say yes here you get support for the TPS6501x series of
Power Management chips. These include voltage regulators, Power Management chips. These include voltage regulators,
......
...@@ -489,7 +489,7 @@ config MMC_SDHCI_ST ...@@ -489,7 +489,7 @@ config MMC_SDHCI_ST
config MMC_OMAP config MMC_OMAP
tristate "TI OMAP Multimedia Card Interface support" tristate "TI OMAP Multimedia Card Interface support"
depends on ARCH_OMAP depends on ARCH_OMAP
depends on TPS65010 || !MACH_OMAP_H2 depends on TPS65010
help help
This selects the TI OMAP Multimedia card Interface. This selects the TI OMAP Multimedia card Interface.
If you have an OMAP board with a Multimedia Card slot, If you have an OMAP board with a Multimedia Card slot,
......
...@@ -118,7 +118,6 @@ config USB_GR_UDC ...@@ -118,7 +118,6 @@ config USB_GR_UDC
config USB_OMAP config USB_OMAP
tristate "OMAP USB Device Controller" tristate "OMAP USB Device Controller"
depends on ARCH_OMAP1 depends on ARCH_OMAP1
depends on ISP1301_OMAP || !(MACH_OMAP_H2 || MACH_OMAP_H3)
help help
Many Texas Instruments OMAP processors have flexible full Many Texas Instruments OMAP processors have flexible full
speed USB device controllers, with support for up to 30 speed USB device controllers, with support for up to 30
......
...@@ -409,7 +409,6 @@ if USB_OHCI_HCD ...@@ -409,7 +409,6 @@ if USB_OHCI_HCD
config USB_OHCI_HCD_OMAP1 config USB_OHCI_HCD_OMAP1
tristate "OHCI support for OMAP1/2 chips" tristate "OHCI support for OMAP1/2 chips"
depends on ARCH_OMAP1 depends on ARCH_OMAP1
depends on ISP1301_OMAP || !(MACH_OMAP_H2 || MACH_OMAP_H3)
default y default y
help help
Enables support for the OHCI controller on OMAP1/2 chips. Enables support for the OHCI controller on OMAP1/2 chips.
......
/* SPDX-License-Identifier: GPL-2.0-only */
/*
* Copyright (C) 2006 Samsung Electronics
* Kyungmin Park <kyungmin.park@samsung.com>
*/
#ifndef ASMARM_ARCH_LED_H
#define ASMARM_ARCH_LED_H
struct omap_led_config {
struct led_classdev cdev;
s16 gpio;
};
struct omap_led_platform_data {
s16 nr_leds;
struct omap_led_config *leds;
};
#endif
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment