docs: hwmon: k8temp, w83793: convert to ReST format

Convert k8temp and w83793 to ReST format, in order to allow them
to be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Documentation/hwmon/k8temp

@@ -2,12 +2,17 @@ Kernel driver k8temp
 ====================
 
 Supported chips:
+
   * AMD Athlon64/FX or Opteron CPUs
+
     Prefix: 'k8temp'
+
     Addresses scanned: PCI space
+
     Datasheet: http://support.amd.com/us/Processor_TechDocs/32559.pdf
 
 Author: Rudolf Marek
+
 Contact: Rudolf Marek <r.marek@assembler.cz>
 
 Description
@@ -27,10 +32,12 @@ implemented sensors.
 
 Mapping of /sys files is as follows:
 
-temp1_input - temperature of Core 0 and "place" 0
-temp2_input - temperature of Core 0 and "place" 1
-temp3_input - temperature of Core 1 and "place" 0
-temp4_input - temperature of Core 1 and "place" 1
+============= ===================================
+temp1_input   temperature of Core 0 and "place" 0
+temp2_input   temperature of Core 0 and "place" 1
+temp3_input   temperature of Core 1 and "place" 0
+temp4_input   temperature of Core 1 and "place" 1
+============= ===================================
 
 Temperatures are measured in degrees Celsius and measurement resolution is
 1 degree C. It is expected that future CPU will have better resolution. The
@@ -48,7 +55,7 @@ computed temperature called TControl, which must be lower than TControlMax.
 
 The relationship is following:
 
-temp1_input - TjOffset*2 < TControlMax,
+	temp1_input - TjOffset*2 < TControlMax,
 
 TjOffset is not yet exported by the driver, TControlMax is usually
 70 degrees C. The rule of the thumb -> CPU temperature should not cross

Documentation/hwmon/w83793

@@ -2,14 +2,18 @@ Kernel driver w83793
 ====================
 
 Supported chips:
+
   * Winbond W83793G/W83793R
+
     Prefix: 'w83793'
+
     Addresses scanned: I2C 0x2c - 0x2f
+
     Datasheet: Still not published
 
 Authors:
-    Yuan Mu (Winbond Electronics)
-    Rudolf Marek <r.marek@assembler.cz>
+    - Yuan Mu (Winbond Electronics)
+    - Rudolf Marek <r.marek@assembler.cz>
 
 
 Module parameters
@@ -17,12 +21,13 @@ Module parameters
 
 * reset int
     (default 0)
+
     This parameter is not recommended, it will lose motherboard specific
     settings. Use 'reset=1' to reset the chip when loading this module.
 
 * force_subclients=bus,caddr,saddr1,saddr2
     This is used to force the i2c addresses for subclients of
-  a certain chip. Typical usage is `force_subclients=0,0x2f,0x4a,0x4b'
+    a certain chip. Typical usage is `force_subclients=0,0x2f,0x4a,0x4b`
     to force the subclients of chip 0x2f on bus 0 to i2c addresses
     0x4a and 0x4b.
 
@@ -47,10 +52,12 @@ This driver implements support for Winbond W83793G/W83793R chips.
 * Temperature sensor types
     Temp1-4 have 2 possible types. It can be read from (and written to)
     temp[1-4]_type.
+
     - If the value is 3, it starts monitoring using a remote termal diode
       (default).
     - If the value is 6, it starts monitoring using the temperature sensor
       in Intel CPU and get result by PECI.
+
     Temp5-6 can be connected to external thermistors (value of
     temp[5-6]_type is 4).