Commit 0fec6513 authored by Joe Perches's avatar Joe Perches Committed by Michael Grzeschik

arcnet: com20020: Use arcnet_<I/O> routines

Simplify and make consistent the current uses of inb/outb
by using the newly introduced arcnet_<I/O> equivalents.

o Add new #defines for register offsets
  There is an register offset, 8, that is unnamed and used as-is.
o Remove old #defines that included the ioaddr
o Remove obfuscating macros by expanding them in-place where appropriate
o Create static inline com20020_set_subaddress for the SET_SUBADR macro

There is an unused arcnet config entry CONFIGSA100_CT6001 which added a
special #define BUS_ALIGN which was introduced but never used in fullhist git
tree commit 22cfce4b82b0 ("[ARCNET]: Fixes.") in Nov 2004 for Linux v2.6.10.

This BUS_ALIGN #define tries to allow 8 bit devices to work on a 16 bit
bus by aligning addresses to 16 bit boundaries.

Move this currently unused CONFIG_SA1100_CT6001 BUS_ALIGN macro from
com20020.h to arcdevice.h.
Signed-off-by: default avatarJoe Perches <joe@perches.com>
Signed-off-by: default avatarMichael Grzeschik <m.grzeschik@pengutronix.de>
parent e5fcfc1f
......@@ -344,28 +344,34 @@ void arcnet_timeout(struct net_device *dev);
/* I/O equivalents */
#ifdef CONFIG_SA1100_CT6001
#define BUS_ALIGN 2 /* 8 bit device on a 16 bit bus - needs padding */
#else
#define BUS_ALIGN 1
#endif
/* addr and offset allow register like names to define the actual IO address.
* A configuration option multiplies the offset for alignment.
*/
#define arcnet_inb(addr, offset) \
inb((addr) + (offset))
inb((addr) + BUS_ALIGN * (offset))
#define arcnet_outb(value, addr, offset) \
outb(value, (addr) + (offset))
outb(value, (addr) + BUS_ALIGN * (offset))
#define arcnet_insb(addr, offset, buffer, count) \
insb((addr) + (offset), buffer, count)
insb((addr) + BUS_ALIGN * (offset), buffer, count)
#define arcnet_outsb(addr, offset, buffer, count) \
outsb((addr) + (offset), buffer, count)
outsb((addr) + BUS_ALIGN * (offset), buffer, count)
#define arcnet_inw(addr, offset) \
inw((addr) + (offset))
inw((addr) + BUS_ALIGN * (offset))
#define arcnet_outw(value, addr, offset) \
outw(value, (addr) + (offset))
outw(value, (addr) + BUS_ALIGN * (offset))
#define arcnet_insw(addr, offset, buffer, count) \
insw((addr) + (offset), buffer, count)
insw((addr) + BUS_ALIGN * (offset), buffer, count)
#define arcnet_outsw(addr, offset, buffer, count) \
outsw((addr) + (offset), buffer, count)
outsw((addr) + BUS_ALIGN * (offset), buffer, count)
#endif /* __KERNEL__ */
#endif /* _LINUX_ARCDEVICE_H */
......@@ -67,7 +67,7 @@ static int __init com20020isa_probe(struct net_device *dev)
ioaddr, ioaddr + ARCNET_TOTAL_SIZE - 1);
return -ENXIO;
}
if (ASTATUS() == 0xFF) {
if (arcnet_inb(ioaddr, COM20020_REG_R_STATUS) == 0xFF) {
arc_printk(D_NORMAL, dev, "IO address %x empty\n", ioaddr);
err = -ENODEV;
goto out;
......@@ -83,20 +83,20 @@ static int __init com20020isa_probe(struct net_device *dev)
* we tell it to start receiving.
*/
arc_printk(D_INIT_REASONS, dev, "intmask was %02Xh\n",
inb(_INTMASK));
outb(0, _INTMASK);
arcnet_inb(ioaddr, COM20020_REG_R_STATUS));
arcnet_outb(0, ioaddr, COM20020_REG_W_INTMASK);
airqmask = probe_irq_on();
outb(NORXflag, _INTMASK);
arcnet_outb(NORXflag, ioaddr, COM20020_REG_W_INTMASK);
udelay(1);
outb(0, _INTMASK);
arcnet_outb(0, ioaddr, COM20020_REG_W_INTMASK);
dev->irq = probe_irq_off(airqmask);
if ((int)dev->irq <= 0) {
arc_printk(D_INIT_REASONS, dev, "Autoprobe IRQ failed first time\n");
airqmask = probe_irq_on();
outb(NORXflag, _INTMASK);
arcnet_outb(NORXflag, ioaddr, COM20020_REG_W_INTMASK);
udelay(5);
outb(0, _INTMASK);
arcnet_outb(0, ioaddr, COM20020_REG_W_INTMASK);
dev->irq = probe_irq_off(airqmask);
if ((int)dev->irq <= 0) {
arc_printk(D_NORMAL, dev, "Autoprobe IRQ failed.\n");
......
......@@ -117,8 +117,8 @@ static int com20020pci_probe(struct pci_dev *pdev,
* ARCNET controller needs
* this access to detect bustype
*/
outb(0x00, ioaddr + 1);
inb(ioaddr + 1);
arcnet_outb(0x00, ioaddr, COM20020_REG_W_COMMAND);
arcnet_inb(ioaddr, COM20020_REG_R_DIAGSTAT);
dev->base_addr = ioaddr;
dev->dev_addr[0] = node;
......@@ -131,7 +131,7 @@ static int com20020pci_probe(struct pci_dev *pdev,
lp->timeout = timeout;
lp->hw.owner = THIS_MODULE;
if (ASTATUS() == 0xFF) {
if (arcnet_inb(ioaddr, COM20020_REG_R_STATUS) == 0xFF) {
pr_err("IO address %Xh is empty!\n", ioaddr);
ret = -EIO;
goto out_port;
......
......@@ -65,11 +65,13 @@ static void com20020_copy_from_card(struct net_device *dev, int bufnum,
int ioaddr = dev->base_addr, ofs = 512 * bufnum + offset;
/* set up the address register */
outb((ofs >> 8) | RDDATAflag | AUTOINCflag, _ADDR_HI);
outb(ofs & 0xff, _ADDR_LO);
arcnet_outb((ofs >> 8) | RDDATAflag | AUTOINCflag,
ioaddr, COM20020_REG_W_ADDR_HI);
arcnet_outb(ofs & 0xff, ioaddr, COM20020_REG_W_ADDR_LO);
/* copy the data */
TIME(dev, "insb", count, insb(_MEMDATA, buf, count));
TIME(dev, "insb", count,
arcnet_insb(ioaddr, COM20020_REG_RW_MEMDATA, buf, count));
}
static void com20020_copy_to_card(struct net_device *dev, int bufnum,
......@@ -78,11 +80,12 @@ static void com20020_copy_to_card(struct net_device *dev, int bufnum,
int ioaddr = dev->base_addr, ofs = 512 * bufnum + offset;
/* set up the address register */
outb((ofs >> 8) | AUTOINCflag, _ADDR_HI);
outb(ofs & 0xff, _ADDR_LO);
arcnet_outb((ofs >> 8) | AUTOINCflag, ioaddr, COM20020_REG_W_ADDR_HI);
arcnet_outb(ofs & 0xff, ioaddr, COM20020_REG_W_ADDR_LO);
/* copy the data */
TIME(dev, "outsb", count, outsb(_MEMDATA, buf, count));
TIME(dev, "outsb", count,
arcnet_outsb(ioaddr, COM20020_REG_RW_MEMDATA, buf, count));
}
/* Reset the card and check some basic stuff during the detection stage. */
......@@ -91,7 +94,9 @@ int com20020_check(struct net_device *dev)
int ioaddr = dev->base_addr, status;
struct arcnet_local *lp = netdev_priv(dev);
ARCRESET0;
arcnet_outb(0x18 | 0x80, ioaddr, COM20020_REG_W_CONFIG);
udelay(5);
arcnet_outb(0x18 , ioaddr, COM20020_REG_W_CONFIG);
mdelay(RESETtime);
lp->setup = lp->clockm ? 0 : (lp->clockp << 1);
......@@ -101,24 +106,24 @@ int com20020_check(struct net_device *dev)
/* Enable P1Mode for backplane mode */
lp->setup = lp->setup | P1MODE;
SET_SUBADR(SUB_SETUP1);
outb(lp->setup, _XREG);
com20020_set_subaddress(lp, ioaddr, SUB_SETUP1);
arcnet_outb(lp->setup, ioaddr, COM20020_REG_W_XREG);
if (lp->clockm != 0) {
SET_SUBADR(SUB_SETUP2);
outb(lp->setup2, _XREG);
com20020_set_subaddress(lp, ioaddr, SUB_SETUP2);
arcnet_outb(lp->setup2, ioaddr, COM20020_REG_W_XREG);
/* must now write the magic "restart operation" command */
mdelay(1);
outb(0x18, _COMMAND);
arcnet_outb(0x18, ioaddr, COM20020_REG_W_COMMAND);
}
lp->config = 0x21 | (lp->timeout << 3) | (lp->backplane << 2);
/* set node ID to 0x42 (but transmitter is disabled, so it's okay) */
SETCONF;
outb(0x42, ioaddr + BUS_ALIGN * 7);
arcnet_outb(lp->config, ioaddr, COM20020_REG_W_CONFIG);
arcnet_outb(0x42, ioaddr, COM20020_REG_W_XREG);
status = ASTATUS();
status = arcnet_inb(ioaddr, COM20020_REG_R_STATUS);
if ((status & 0x99) != (NORXflag | TXFREEflag | RESETflag)) {
arc_printk(D_NORMAL, dev, "status invalid (%Xh).\n", status);
......@@ -127,20 +132,21 @@ int com20020_check(struct net_device *dev)
arc_printk(D_INIT_REASONS, dev, "status after reset: %X\n", status);
/* Enable TX */
outb(0x39, _CONFIG);
outb(inb(ioaddr + BUS_ALIGN * 8), ioaddr + BUS_ALIGN * 7);
arcnet_outb(0x39, ioaddr, COM20020_REG_W_CONFIG);
arcnet_outb(arcnet_inb(ioaddr, 8), ioaddr, COM20020_REG_W_XREG);
ACOMMAND(CFLAGScmd | RESETclear | CONFIGclear);
status = ASTATUS();
arcnet_outb(CFLAGScmd | RESETclear | CONFIGclear,
ioaddr, COM20020_REG_W_COMMAND);
status = arcnet_inb(ioaddr, COM20020_REG_R_STATUS);
arc_printk(D_INIT_REASONS, dev, "status after reset acknowledged: %X\n",
status);
/* Read first location of memory */
outb(0 | RDDATAflag | AUTOINCflag, _ADDR_HI);
outb(0, _ADDR_LO);
arcnet_outb(0 | RDDATAflag | AUTOINCflag,
ioaddr, COM20020_REG_W_ADDR_HI);
arcnet_outb(0, ioaddr, COM20020_REG_W_ADDR_LO);
status = inb(_MEMDATA);
status = arcnet_inb(ioaddr, COM20020_REG_RW_MEMDATA);
if (status != TESTvalue) {
arc_printk(D_NORMAL, dev, "Signature byte not found (%02Xh != D1h).\n",
status);
......@@ -156,8 +162,8 @@ static int com20020_set_hwaddr(struct net_device *dev, void *addr)
struct sockaddr *hwaddr = addr;
memcpy(dev->dev_addr, hwaddr->sa_data, 1);
SET_SUBADR(SUB_NODE);
outb(dev->dev_addr[0], _XREG);
com20020_set_subaddress(lp, ioaddr, SUB_NODE);
arcnet_outb(dev->dev_addr[0], ioaddr, COM20020_REG_W_XREG);
return 0;
}
......@@ -194,24 +200,24 @@ int com20020_found(struct net_device *dev, int shared)
/* FIXME: do this some other way! */
if (!dev->dev_addr[0])
dev->dev_addr[0] = inb(ioaddr + BUS_ALIGN * 8);
dev->dev_addr[0] = arcnet_inb(ioaddr, 8);
SET_SUBADR(SUB_SETUP1);
outb(lp->setup, _XREG);
com20020_set_subaddress(lp, ioaddr, SUB_SETUP1);
arcnet_outb(lp->setup, ioaddr, COM20020_REG_W_XREG);
if (lp->card_flags & ARC_CAN_10MBIT) {
SET_SUBADR(SUB_SETUP2);
outb(lp->setup2, _XREG);
com20020_set_subaddress(lp, ioaddr, SUB_SETUP2);
arcnet_outb(lp->setup2, ioaddr, COM20020_REG_W_XREG);
/* must now write the magic "restart operation" command */
mdelay(1);
outb(0x18, _COMMAND);
arcnet_outb(0x18, ioaddr, COM20020_REG_W_COMMAND);
}
lp->config = 0x20 | (lp->timeout << 3) | (lp->backplane << 2) | 1;
/* Default 0x38 + register: Node ID */
SETCONF;
outb(dev->dev_addr[0], _XREG);
arcnet_outb(lp->config, ioaddr, COM20020_REG_W_CONFIG);
arcnet_outb(dev->dev_addr[0], ioaddr, COM20020_REG_W_XREG);
/* reserve the irq */
if (request_irq(dev->irq, arcnet_interrupt, shared,
......@@ -264,23 +270,26 @@ static int com20020_reset(struct net_device *dev, int really_reset)
arc_printk(D_DEBUG, dev, "%s: %d: %s: dev: %p, lp: %p, dev->name: %s\n",
__FILE__, __LINE__, __func__, dev, lp, dev->name);
arc_printk(D_INIT, dev, "Resetting %s (status=%02Xh)\n",
dev->name, ASTATUS());
dev->name, arcnet_inb(ioaddr, COM20020_REG_R_STATUS));
arc_printk(D_DEBUG, dev, "%s: %d: %s\n", __FILE__, __LINE__, __func__);
lp->config = TXENcfg | (lp->timeout << 3) | (lp->backplane << 2);
/* power-up defaults */
SETCONF;
arcnet_outb(lp->config, ioaddr, COM20020_REG_W_CONFIG);
arc_printk(D_DEBUG, dev, "%s: %d: %s\n", __FILE__, __LINE__, __func__);
if (really_reset) {
/* reset the card */
ARCRESET;
arcnet_outb(lp->config | 0x80, ioaddr, COM20020_REG_W_CONFIG);
udelay(5);
arcnet_outb(lp->config, ioaddr, COM20020_REG_W_CONFIG);
mdelay(RESETtime * 2);
/* COM20020 seems to be slower sometimes */
}
/* clear flags & end reset */
arc_printk(D_DEBUG, dev, "%s: %d: %s\n", __FILE__, __LINE__, __func__);
ACOMMAND(CFLAGScmd | RESETclear | CONFIGclear);
arcnet_outb(CFLAGScmd | RESETclear | CONFIGclear,
ioaddr, COM20020_REG_W_COMMAND);
/* verify that the ARCnet signature byte is present */
arc_printk(D_DEBUG, dev, "%s: %d: %s\n", __FILE__, __LINE__, __func__);
......@@ -294,7 +303,8 @@ static int com20020_reset(struct net_device *dev, int really_reset)
return 1;
}
/* enable extended (512-byte) packets */
ACOMMAND(CONFIGcmd | EXTconf);
arcnet_outb(CONFIGcmd | EXTconf, ioaddr, COM20020_REG_W_COMMAND);
arc_printk(D_DEBUG, dev, "%s: %d: %s\n", __FILE__, __LINE__, __func__);
/* done! return success. */
......@@ -306,21 +316,22 @@ static void com20020_setmask(struct net_device *dev, int mask)
u_int ioaddr = dev->base_addr;
arc_printk(D_DURING, dev, "Setting mask to %x at %x\n", mask, ioaddr);
AINTMASK(mask);
arcnet_outb(mask, ioaddr, COM20020_REG_W_INTMASK);
}
static void com20020_command(struct net_device *dev, int cmd)
{
u_int ioaddr = dev->base_addr;
ACOMMAND(cmd);
arcnet_outb(cmd, ioaddr, COM20020_REG_W_COMMAND);
}
static int com20020_status(struct net_device *dev)
{
u_int ioaddr = dev->base_addr;
return ASTATUS() + (ADIAGSTATUS() << 8);
return arcnet_inb(ioaddr, COM20020_REG_R_STATUS) +
(arcnet_inb(ioaddr, COM20020_REG_R_DIAGSTAT) << 8);
}
static void com20020_close(struct net_device *dev)
......@@ -330,7 +341,7 @@ static void com20020_close(struct net_device *dev)
/* disable transmitter */
lp->config &= ~TXENcfg;
SETCONF;
arcnet_outb(lp->config, ioaddr, COM20020_REG_W_CONFIG);
}
/* Set or clear the multicast filter for this adaptor.
......@@ -349,16 +360,16 @@ static void com20020_set_mc_list(struct net_device *dev)
/* Enable promiscuous mode */
if (!(lp->setup & PROMISCset))
arc_printk(D_NORMAL, dev, "Setting promiscuous flag...\n");
SET_SUBADR(SUB_SETUP1);
com20020_set_subaddress(lp, ioaddr, SUB_SETUP1);
lp->setup |= PROMISCset;
outb(lp->setup, _XREG);
arcnet_outb(lp->setup, ioaddr, COM20020_REG_W_XREG);
} else {
/* Disable promiscuous mode, use normal mode */
if ((lp->setup & PROMISCset))
arc_printk(D_NORMAL, dev, "Resetting promiscuous flag...\n");
SET_SUBADR(SUB_SETUP1);
com20020_set_subaddress(lp, ioaddr, SUB_SETUP1);
lp->setup &= ~PROMISCset;
outb(lp->setup, _XREG);
arcnet_outb(lp->setup, ioaddr, COM20020_REG_W_XREG);
}
}
......
/*
* Linux ARCnet driver - COM20020 chipset support - function declarations
*
*
* Written 1997 by David Woodhouse.
* Written 1994-1999 by Avery Pennarun.
* Derived from skeleton.c by Donald Becker.
......@@ -34,13 +34,6 @@ extern const struct net_device_ops com20020_netdev_ops;
/* The number of low I/O ports used by the card. */
#define ARCNET_TOTAL_SIZE 8
/* various register addresses */
#ifdef CONFIG_SA1100_CT6001
#define BUS_ALIGN 2 /* 8 bit device on a 16 bit bus - needs padding */
#else
#define BUS_ALIGN 1
#endif
#define PLX_PCI_MAX_CARDS 2
struct com20020_pci_channel_map {
......@@ -71,17 +64,18 @@ struct com20020_dev {
int index;
};
#define _INTMASK (ioaddr+BUS_ALIGN*0) /* writable */
#define _STATUS (ioaddr+BUS_ALIGN*0) /* readable */
#define _COMMAND (ioaddr+BUS_ALIGN*1) /* standard arcnet commands */
#define _DIAGSTAT (ioaddr+BUS_ALIGN*1) /* diagnostic status register */
#define _ADDR_HI (ioaddr+BUS_ALIGN*2) /* control registers for IO-mapped memory */
#define _ADDR_LO (ioaddr+BUS_ALIGN*3)
#define _MEMDATA (ioaddr+BUS_ALIGN*4) /* data port for IO-mapped memory */
#define _SUBADR (ioaddr+BUS_ALIGN*5) /* the extended port _XREG refers to */
#define _CONFIG (ioaddr+BUS_ALIGN*6) /* configuration register */
#define _XREG (ioaddr+BUS_ALIGN*7) /* extra registers (indexed by _CONFIG
or _SUBADR) */
#define COM20020_REG_W_INTMASK 0 /* writable */
#define COM20020_REG_R_STATUS 0 /* readable */
#define COM20020_REG_W_COMMAND 1 /* standard arcnet commands */
#define COM20020_REG_R_DIAGSTAT 1 /* diagnostic status */
#define COM20020_REG_W_ADDR_HI 2 /* control for IO-mapped memory */
#define COM20020_REG_W_ADDR_LO 3
#define COM20020_REG_RW_MEMDATA 4 /* data port for IO-mapped memory */
#define COM20020_REG_W_SUBADR 5 /* the extended port _XREG refers to */
#define COM20020_REG_W_CONFIG 6 /* configuration */
#define COM20020_REG_W_XREG 7 /* extra
* (indexed by _CONFIG or _SUBADDR)
*/
/* in the ADDR_HI register */
#define RDDATAflag 0x80 /* next access is a read (not a write) */
......@@ -109,37 +103,15 @@ struct com20020_dev {
#define SUB_BUSCTL 5 /* bus control options */
#define SUB_DMACOUNT 6 /* DMA count options */
#define SET_SUBADR(x) do { \
if ((x) < 4) \
{ \
lp->config = (lp->config & ~0x03) | (x); \
SETCONF; \
} \
else \
{ \
outb(x, _SUBADR); \
} \
} while (0)
#undef ARCRESET
#undef ASTATUS
#undef ACOMMAND
#undef AINTMASK
#define ARCRESET { outb(lp->config | 0x80, _CONFIG); \
udelay(5); \
outb(lp->config , _CONFIG); \
}
#define ARCRESET0 { outb(0x18 | 0x80, _CONFIG); \
udelay(5); \
outb(0x18 , _CONFIG); \
}
#define ASTATUS() inb(_STATUS)
#define ADIAGSTATUS() inb(_DIAGSTAT)
#define ACOMMAND(cmd) outb((cmd),_COMMAND)
#define AINTMASK(msk) outb((msk),_INTMASK)
#define SETCONF outb(lp->config, _CONFIG)
static inline void com20020_set_subaddress(struct arcnet_local *lp,
int ioaddr, int val)
{
if (val < 4) {
lp->config = (lp->config & ~0x03) | val;
arcnet_outb(lp->config, ioaddr, COM20020_REG_W_CONFIG);
} else {
arcnet_outb(val, ioaddr, COM20020_REG_W_SUBADR);
}
}
#endif /* __COM20020_H */
......@@ -56,25 +56,26 @@ static void regdump(struct net_device *dev)
int count;
netdev_dbg(dev, "register dump:\n");
for (count = ioaddr; count < ioaddr + 16; count++) {
for (count = 0; count < 16; count++) {
if (!(count % 16))
pr_cont("%04X:", count);
pr_cont(" %02X", inb(count));
pr_cont("%04X:", ioaddr + count);
pr_cont(" %02X", arcnet_inb(ioaddr, count));
}
pr_cont("\n");
netdev_dbg(dev, "buffer0 dump:\n");
/* set up the address register */
count = 0;
outb((count >> 8) | RDDATAflag | AUTOINCflag, _ADDR_HI);
outb(count & 0xff, _ADDR_LO);
arcnet_outb((count >> 8) | RDDATAflag | AUTOINCflag,
ioaddr, com20020_REG_W_ADDR_HI);
arcnet_outb(count & 0xff, ioaddr, COM20020_REG_W_ADDR_LO);
for (count = 0; count < 256 + 32; count++) {
if (!(count % 16))
pr_cont("%04X:", count);
/* copy the data */
pr_cont(" %02X", inb(_MEMDATA));
pr_cont(" %02X", arcnet_inb(ioaddr, COM20020_REG_RW_MEMDATA));
}
pr_cont("\n");
#endif
......@@ -292,7 +293,9 @@ static int com20020_resume(struct pcmcia_device *link)
int ioaddr = dev->base_addr;
struct arcnet_local *lp = netdev_priv(dev);
ARCRESET;
arcnet_outb(lp->config | 0x80, ioaddr, COM20020_REG_W_CONFIG);
udelay(5);
arcnet_outb(lp->config, ioaddr, COM20020_REG_W_CONFIG);
}
return 0;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment