Commit 1010faa4 authored by Derek Robson's avatar Derek Robson Committed by Greg Kroah-Hartman

Drivers: ccree: ssi_request_mgr.c - align block comments

Fixed block comment alignment, Style fix only
Found using checkpatch
Signed-off-by: default avatarDerek Robson <robsonde@gmail.com>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
parent 2f930981
......@@ -300,8 +300,9 @@ static inline int request_mgr_queues_status_check(
unsigned long poll_queue;
/* SW queue is checked only once as it will not
be chaned during the poll becasue the spinlock_bh
is held by the thread */
* be chaned during the poll becasue the spinlock_bh
* is held by the thread
*/
if (unlikely(((req_mgr_h->req_queue_head + 1) &
(MAX_REQUEST_QUEUE_SIZE - 1)) ==
req_mgr_h->req_queue_tail)) {
......@@ -384,8 +385,9 @@ int send_request(
spin_lock_bh(&req_mgr_h->hw_lock);
/* Check if there is enough place in the SW/HW queues
in case iv gen add the max size and in case of no dout add 1
for the internal completion descriptor */
* in case iv gen add the max size and in case of no dout add 1
* for the internal completion descriptor
*/
rc = request_mgr_queues_status_check(req_mgr_h,
cc_base,
max_required_seq_len);
......@@ -397,7 +399,8 @@ int send_request(
if (rc != -EAGAIN) {
/* Any error other than HW queue full
(SW queue is full) */
* (SW queue is full)
*/
#if defined (CONFIG_PM_RUNTIME) || defined (CONFIG_PM_SLEEP)
ssi_power_mgr_runtime_put_suspend(&drvdata->plat_dev->dev);
#endif
......@@ -409,7 +412,8 @@ int send_request(
} while (1);
/* Additional completion descriptor is needed incase caller did not
enabled any DLLI/MLLI DOUT bit in the given sequence */
* enabled any DLLI/MLLI DOUT bit in the given sequence
*/
if (!is_dout) {
init_completion(&ssi_req->seq_compl);
ssi_req->user_cb = request_mgr_complete;
......@@ -481,7 +485,8 @@ int send_request(
if (!is_dout) {
/* Wait upon sequence completion.
* Return "0" -Operation done successfully. */
* Return "0" -Operation done successfully.
*/
return wait_for_completion_interruptible(&ssi_req->seq_compl);
} else {
/* Operation still in process */
......@@ -633,7 +638,8 @@ static void comp_handler(unsigned long devarg)
/* ISR-to-Tasklet latency */
if (request_mgr_handle->axi_completed) {
/* Only if actually reflects ISR-to-completion-handling latency, i.e.,
not duplicate as a result of interrupt after AXIM_MON_ERR clear, before end of loop */
* not duplicate as a result of interrupt after AXIM_MON_ERR clear, before end of loop
*/
END_CYCLE_COUNT_AT(drvdata->isr_exit_cycles, STAT_OP_TYPE_GENERIC, STAT_PHASE_1);
}
......@@ -641,7 +647,8 @@ static void comp_handler(unsigned long devarg)
do {
proc_completions(drvdata);
/* At this point (after proc_completions()), request_mgr_handle->axi_completed is always 0.
The following assignment was changed to = (previously was +=) to conform KW restrictions. */
* The following assignment was changed to = (previously was +=) to conform KW restrictions.
*/
request_mgr_handle->axi_completed = CC_REG_FLD_GET(CRY_KERNEL, AXIM_MON_COMP, VALUE,
CC_HAL_READ_REGISTER(AXIM_MON_BASE_OFFSET));
} while (request_mgr_handle->axi_completed > 0);
......@@ -663,9 +670,9 @@ static void comp_handler(unsigned long devarg)
}
/*
resume the queue configuration - no need to take the lock as this happens inside
the spin lock protection
*/
* resume the queue configuration - no need to take the lock as this happens inside
* the spin lock protection
*/
#if defined (CONFIG_PM_RUNTIME) || defined (CONFIG_PM_SLEEP)
int ssi_request_mgr_runtime_resume_queue(struct ssi_drvdata *drvdata)
{
......@@ -679,9 +686,9 @@ int ssi_request_mgr_runtime_resume_queue(struct ssi_drvdata *drvdata)
}
/*
suspend the queue configuration. Since it is used for the runtime suspend
only verify that the queue can be suspended.
*/
* suspend the queue configuration. Since it is used for the runtime suspend
* only verify that the queue can be suspended.
*/
int ssi_request_mgr_runtime_suspend_queue(struct ssi_drvdata *drvdata)
{
struct ssi_request_mgr_handle * request_mgr_handle =
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment