pinctrl: assume map table entries can't have a NULL name field

pinctrl_register_mappings() already requires that every mapping table
entry have a non-NULL name field.

Logically, this makes sense too; drivers should always request a specific
named state so they know what they're getting. Relying on getting the
first mentioned state in the mapping table is error-prone, and a nasty
special case to implement, given that a given the mapping table may define
multiple states for a device.

Remove a small part of the documentation that talked about optionally
requesting a specific state; it's mandatory now.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Documentation/pinctrl.txt

@@ -782,16 +782,19 @@ spi on the second function mapping:
 static const struct pinctrl_map __initdata mapping[] = {
 	{
 		.dev_name = "foo-spi.0",
+		.name = PINCTRL_STATE_DEFAULT,
 		.ctrl_dev_name = "pinctrl-foo",
 		.function = "spi0",
 	},
 	{
 		.dev_name = "foo-i2c.0",
+		.name = PINCTRL_STATE_DEFAULT,
 		.ctrl_dev_name = "pinctrl-foo",
 		.function = "i2c0",
 	},
 	{
 		.dev_name = "foo-mmc.0",
+		.name = PINCTRL_STATE_DEFAULT,
 		.ctrl_dev_name = "pinctrl-foo",
 		.function = "mmc0",
 	},
@@ -944,10 +947,6 @@ foo_remove()
 	pinctrl_put(state->p);
 }
 
-If you want to grab a specific control mapping and not just the first one
-found for this device you can specify a specific mapping name, for example in
-the above example the second i2c0 setting: pinctrl_get(&device, "spi0-pos-B");
-
 This get/enable/disable/put sequence can just as well be handled by bus drivers
 if you don't want each and every driver to handle it and you know the
 arrangement on your bus.

arch/arm/mach-u300/core.c

@@ -1612,9 +1612,9 @@ static struct pinctrl_map __initdata u300_pinmux_map[] = {
 	PIN_MAP_SYS_HOG("pinctrl-u300", "emif0"),
 	PIN_MAP_SYS_HOG("pinctrl-u300", "emif1"),
 	/* per-device maps for MMC/SD, SPI and UART */
-	PIN_MAP("MMCSD", "pinctrl-u300", "mmc0", "mmci"),
-	PIN_MAP("SPI", "pinctrl-u300", "spi0", "pl022"),
-	PIN_MAP("UART0", "pinctrl-u300", "uart0", "uart0"),
+	PIN_MAP(PINCTRL_STATE_DEFAULT, "pinctrl-u300", "mmc0", "mmci"),
+	PIN_MAP(PINCTRL_STATE_DEFAULT, "pinctrl-u300", "spi0", "pl022"),
+	PIN_MAP(PINCTRL_STATE_DEFAULT, "pinctrl-u300", "uart0", "uart0"),
 };
 
 struct u300_mux_hog {
@@ -1646,7 +1646,7 @@ static int __init u300_pinctrl_fetch(void)
 		struct pinctrl *p;
 		int ret;
 
-		p = pinctrl_get(u300_mux_hogs[i].dev, NULL);
+		p = pinctrl_get(u300_mux_hogs[i].dev, PINCTRL_STATE_DEFAULT);
 		if (IS_ERR(p)) {
 			pr_err("u300: could not get pinmux hog %s\n",
 			       u300_mux_hogs[i].name);

drivers/pinctrl/core.c

@@ -461,8 +461,8 @@ static struct pinctrl *pinctrl_get_locked(struct device *dev, const char *name)
 	int i;
 	struct pinctrl_map const *map;
 
-	/* We must have a dev name */
-	if (WARN_ON(!dev))
+	/* We must have both a dev and state name */
+	if (WARN_ON(!dev || !name))
 		return ERR_PTR(-EINVAL);
 
 	devname = dev_name(dev);
@@ -504,16 +504,9 @@ static struct pinctrl *pinctrl_get_locked(struct device *dev, const char *name)
 		if (strcmp(map->dev_name, devname))
 			continue;
 
-		/*
-		 * If we're looking for a specific named map, this must match,
-		 * else we loop and look for the next.
-		 */
-		if (name != NULL) {
-			if (map->name == NULL)
-				continue;
-			if (strcmp(map->name, name))
-				continue;
-		}
+		/* State name must be the one we're looking for */
+		if (strcmp(map->name, name))
+			continue;
 
 		ret = pinmux_apply_muxmap(pctldev, p, dev, devname, map);
 		if (ret) {

drivers/tty/serial/sirfsoc_uart.c

@@ -673,7 +673,7 @@ int sirfsoc_uart_probe(struct platform_device *pdev)
 	port->irq = res->start;
 
 	if (sirfport->hw_flow_ctrl) {
-		sirfport->p = pinctrl_get(&pdev->dev, NULL);
+		sirfport->p = pinctrl_get(&pdev->dev, PINCTRL_STATE_DEFAULT);
 		ret = IS_ERR(sirfport->p);
 		if (ret)
 			goto pin_err;