Commit 13e2a6fd authored by Ludovic Desroches's avatar Ludovic Desroches Committed by Nicolas Ferre

ARM: at91/dt: sama5d2 Xplained: add several devices

Add sdmmc and flexcom devices
Signed-off-by: default avatarLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: default avatarCyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: default avatarAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: default avatarNicolas Ferre <nicolas.ferre@atmel.com>
parent 1392f7c9
......@@ -45,6 +45,7 @@
/dts-v1/;
#include "sama5d2.dtsi"
#include "sama5d2-pinfunc.h"
#include <dt-bindings/mfd/atmel-flexcom.h>
/ {
model = "Atmel SAMA5D2 Xplained";
......@@ -82,6 +83,22 @@ usb2: ehci@00500000 {
status = "okay";
};
sdmmc0: sdio-host@a0000000 {
bus-width = <8>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sdmmc0_default>;
non-removable;
mmc-ddr-1_8v;
status = "okay";
};
sdmmc1: sdio-host@b0000000 {
bus-width = <4>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sdmmc1_default>;
status = "okay"; /* conflict with qspi0 */
};
apb {
spi0: spi@f8000000 {
pinctrl-names = "default";
......@@ -172,12 +189,49 @@ vdd_sdhc_1v8_reg: LDO_REG4 {
};
};
flx0: flexcom@f8034000 {
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
status = "disabled"; /* conflict with ISC_D2 & ISC_D3 data pins */
uart5: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
clocks = <&flx0_clk>;
clock-names = "usart";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flx0_default>;
atmel,fifo-size = <32>;
status = "okay";
};
};
uart3: serial@fc008000 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3_default>;
status = "okay";
};
flx4: flexcom@fc018000 {
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
status = "okay";
i2c2: i2c@600 {
compatible = "atmel,sama5d2-i2c";
reg = <0x600 0x200>;
interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <0>, <0>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
clocks = <&flx4_clk>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flx4_default>;
atmel,fifo-size = <16>;
status = "okay";
};
};
i2c1: i2c@fc028000 {
dmas = <0>, <0>;
pinctrl-names = "default";
......@@ -192,6 +246,18 @@ at24@54 {
};
pinctrl@fc038000 {
pinctrl_flx0_default: flx0_default {
pinmux = <PIN_PB28__FLEXCOM0_IO0>,
<PIN_PB29__FLEXCOM0_IO1>;
bias-disable;
};
pinctrl_flx4_default: flx4_default {
pinmux = <PIN_PD12__FLEXCOM4_IO0>,
<PIN_PD13__FLEXCOM4_IO1>;
bias-disable;
};
pinctrl_i2c0_default: i2c0_default {
pinmux = <PIN_PD21__TWD0>,
<PIN_PD22__TWCK0>;
......@@ -218,6 +284,46 @@ pinctrl_macb0_default: macb0_default {
bias-disable;
};
pinctrl_sdmmc0_default: sdmmc0_default {
cmd_data {
pinmux = <PIN_PA1__SDMMC0_CMD>,
<PIN_PA2__SDMMC0_DAT0>,
<PIN_PA3__SDMMC0_DAT1>,
<PIN_PA4__SDMMC0_DAT2>,
<PIN_PA5__SDMMC0_DAT3>,
<PIN_PA6__SDMMC0_DAT4>,
<PIN_PA7__SDMMC0_DAT5>,
<PIN_PA8__SDMMC0_DAT6>,
<PIN_PA9__SDMMC0_DAT7>;
bias-pull-up;
};
ck_cd_rstn_vddsel {
pinmux = <PIN_PA0__SDMMC0_CK>,
<PIN_PA10__SDMMC0_RSTN>,
<PIN_PA11__SDMMC0_VDDSEL>,
<PIN_PA13__SDMMC0_CD>;
bias-disable;
};
};
pinctrl_sdmmc1_default: sdmmc1_default {
cmd_data {
pinmux = <PIN_PA28__SDMMC1_CMD>,
<PIN_PA18__SDMMC1_DAT0>,
<PIN_PA19__SDMMC1_DAT1>,
<PIN_PA20__SDMMC1_DAT2>,
<PIN_PA21__SDMMC1_DAT3>;
bias-pull-up;
};
conf-ck_cd {
pinmux = <PIN_PA22__SDMMC1_CK>,
<PIN_PA30__SDMMC1_CD>;
bias-disable;
};
};
pinctrl_spi0_default: spi0_default {
pinmux = <PIN_PA14__SPI0_SPCK>,
<PIN_PA15__SPI0_MOSI>,
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment