Commit 14c815a9 authored by Ilias Apalodimas's avatar Ilias Apalodimas Committed by David S. Miller

Documentation: networking: add cpsw switchdev based driver documentation

A new cpsw dirver based on switchdev was added. Add documentation about
basic configuration and future features
Signed-off-by: default avatarIlias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: default avatarGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent da84e50c
* Texas Instruments CPSW switchdev based ethernet driver 2.0
- Port renaming
On older udev versions renaming of ethX to swXpY will not be automatically
supported
In order to rename via udev:
ip -d link show dev sw0p1 | grep switchid
SUBSYSTEM=="net", ACTION=="add", ATTR{phys_switch_id}==<switchid>, \
ATTR{phys_port_name}!="", NAME="sw0$attr{phys_port_name}"
====================
# Dual mac mode
====================
- The new (cpsw_new.c) driver is operating in dual-emac mode by default, thus
working as 2 individual network interfaces. Main differences from legacy CPSW
driver are:
- optimized promiscuous mode: The P0_UNI_FLOOD (both ports) is enabled in
addition to ALLMULTI (current port) instead of ALE_BYPASS.
So, Ports in promiscuous mode will keep possibility of mcast and vlan filtering,
which is provides significant benefits when ports are joined to the same bridge,
but without enabling "switch" mode, or to different bridges.
- learning disabled on ports as it make not too much sense for
segregated ports - no forwarding in HW.
- enabled basic support for devlink.
devlink dev show
platform/48484000.switch
devlink dev param show
platform/48484000.switch:
name switch_mode type driver-specific
values:
cmode runtime value false
name ale_bypass type driver-specific
values:
cmode runtime value false
Devlink configuration parameters
====================
See Documentation/networking/devlink-params-ti-cpsw-switch.txt
====================
# Bridging in dual mac mode
====================
The dual_mac mode requires two vids to be reserved for internal purposes,
which, by default, equal CPSW Port numbers. As result, bridge has to be
configured in vlan unaware mode or default_pvid has to be adjusted.
ip link add name br0 type bridge
ip link set dev br0 type bridge vlan_filtering 0
echo 0 > /sys/class/net/br0/bridge/default_pvid
ip link set dev sw0p1 master br0
ip link set dev sw0p2 master br0
- or -
ip link add name br0 type bridge
ip link set dev br0 type bridge vlan_filtering 0
echo 100 > /sys/class/net/br0/bridge/default_pvid
ip link set dev br0 type bridge vlan_filtering 1
ip link set dev sw0p1 master br0
ip link set dev sw0p2 master br0
====================
# Enabling "switch"
====================
The Switch mode can be enabled by configuring devlink driver parameter
"switch_mode" to 1/true:
devlink dev param set platform/48484000.switch \
name switch_mode value 1 cmode runtime
This can be done regardless of the state of Port's netdev devices - UP/DOWN, but
Port's netdev devices have to be in UP before joining to the bridge to avoid
overwriting of bridge configuration as CPSW switch driver copletly reloads its
configuration when first Port changes its state to UP.
When the both interfaces joined the bridge - CPSW switch driver will enable
marking packets with offload_fwd_mark flag unless "ale_bypass=0"
All configuration is implemented via switchdev API.
====================
# Bridge setup
====================
devlink dev param set platform/48484000.switch \
name switch_mode value 1 cmode runtime
ip link add name br0 type bridge
ip link set dev br0 type bridge ageing_time 1000
ip link set dev sw0p1 up
ip link set dev sw0p2 up
ip link set dev sw0p1 master br0
ip link set dev sw0p2 master br0
[*] bridge vlan add dev br0 vid 1 pvid untagged self
[*] if vlan_filtering=1. where default_pvid=1
=================
# On/off STP
=================
ip link set dev BRDEV type bridge stp_state 1/0
Note. Steps [*] are mandatory.
====================
# VLAN configuration
====================
bridge vlan add dev br0 vid 1 pvid untagged self <---- add cpu port to VLAN 1
Note. This step is mandatory for bridge/default_pvid.
=================
# Add extra VLANs
=================
1. untagged:
bridge vlan add dev sw0p1 vid 100 pvid untagged master
bridge vlan add dev sw0p2 vid 100 pvid untagged master
bridge vlan add dev br0 vid 100 pvid untagged self <---- Add cpu port to VLAN100
2. tagged:
bridge vlan add dev sw0p1 vid 100 master
bridge vlan add dev sw0p2 vid 100 master
bridge vlan add dev br0 vid 100 pvid tagged self <---- Add cpu port to VLAN100
====
FDBs
====
FDBs are automatically added on the appropriate switch port upon detection
Manually adding FDBs:
bridge fdb add aa:bb:cc:dd:ee:ff dev sw0p1 master vlan 100
bridge fdb add aa:bb:cc:dd:ee:fe dev sw0p2 master <---- Add on all VLANs
====
MDBs
====
MDBs are automatically added on the appropriate switch port upon detection
Manually adding MDBs:
bridge mdb add dev br0 port sw0p1 grp 239.1.1.1 permanent vid 100
bridge mdb add dev br0 port sw0p1 grp 239.1.1.1 permanent <---- Add on all VLANs
==================
Multicast flooding
==================
CPU port mcast_flooding is always on
Turning flooding on/off on swithch ports:
bridge link set dev sw0p1 mcast_flood on/off
==================
Access and Trunk port
==================
bridge vlan add dev sw0p1 vid 100 pvid untagged master
bridge vlan add dev sw0p2 vid 100 master
bridge vlan add dev br0 vid 100 self
ip link add link br0 name br0.100 type vlan id 100
Note. Setting PVID on Bridge device itself working only for
default VLAN (default_pvid).
=====================
NFS
=====================
The only way for NFS to work is by chrooting to a minimal environment when
switch configuration that will affect connectivity is needed.
Assuming you are booting NFS with eth1 interface(the script is hacky and
it's just there to prove NFS is doable).
setup.sh:
#!/bin/sh
mkdir proc
mount -t proc none /proc
ifconfig br0 > /dev/null
if [ $? -ne 0 ]; then
echo "Setting up bridge"
ip link add name br0 type bridge
ip link set dev br0 type bridge ageing_time 1000
ip link set dev br0 type bridge vlan_filtering 1
ip link set eth1 down
ip link set eth1 name sw0p1
ip link set dev sw0p1 up
ip link set dev sw0p2 up
ip link set dev sw0p2 master br0
ip link set dev sw0p1 master br0
bridge vlan add dev br0 vid 1 pvid untagged self
ifconfig sw0p1 0.0.0.0
udhchc -i br0
fi
umount /proc
run_nfs.sh:
#!/bin/sh
mkdir /tmp/root/bin -p
mkdir /tmp/root/lib -p
cp -r /lib/ /tmp/root/
cp -r /bin/ /tmp/root/
cp /sbin/ip /tmp/root/bin
cp /sbin/bridge /tmp/root/bin
cp /sbin/ifconfig /tmp/root/bin
cp /sbin/udhcpc /tmp/root/bin
cp /path/to/setup.sh /tmp/root/bin
chroot /tmp/root/ busybox sh /bin/setup.sh
run ./run_nfs.sh
ale_bypass [DEVICE, DRIVER-SPECIFIC]
Allows to enable ALE_CONTROL(4).BYPASS mode for debug purposes.
All packets will be sent to the Host port only if enabled.
Type: bool
Configuration mode: runtime
switch_mode [DEVICE, DRIVER-SPECIFIC]
Enable switch mode
Type: bool
Configuration mode: runtime
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment