Commit 14da3ed8 authored by Laurent Pinchart's avatar Laurent Pinchart

devicetree/bindings: display: Document common panel properties

Document properties common to several display panels in a central
location that can be referenced by the panel device tree bindings.
Signed-off-by: default avatarLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: default avatarRob Herring <robh@kernel.org>
parent e1b489d2
Common Properties for Display Panel
===================================
This document defines device tree properties common to several classes of
display panels. It doesn't constitue a device tree binding specification by
itself but is meant to be referenced by device tree bindings.
When referenced from panel device tree bindings the properties defined in this
document are defined as follows. The panel device tree bindings are
responsible for defining whether each property is required or optional.
Descriptive Properties
----------------------
- width-mm,
- height-mm: The width-mm and height-mm specify the width and height of the
physical area where images are displayed. These properties are expressed in
millimeters and rounded to the closest unit.
- label: The label property specifies a symbolic name for the panel as a
string suitable for use by humans. It typically contains a name inscribed on
the system (e.g. as an affixed label) or specified in the system's
documentation (e.g. in the user's manual).
If no such name exists, and unless the property is mandatory according to
device tree bindings, it shall rather be omitted than constructed of
non-descriptive information. For instance an LCD panel in a system that
contains a single panel shall not be labelled "LCD" if that name is not
inscribed on the system or used in a descriptive fashion in system
documentation.
Display Timings
---------------
- panel-timing: Most display panels are restricted to a single resolution and
require specific display timings. The panel-timing subnode expresses those
timings as specified in the timing subnode section of the display timing
bindings defined in
Documentation/devicetree/bindings/display/display-timing.txt.
Connectivity
------------
- ports: Panels receive video data through one or multiple connections. While
the nature of those connections is specific to the panel type, the
connectivity is expressed in a standard fashion using ports as specified in
the device graph bindings defined in
Documentation/devicetree/bindings/graph.txt.
- ddc-i2c-bus: Some panels expose EDID information through an I2C-compatible
bus such as DDC2 or E-DDC. For such panels the ddc-i2c-bus contains a
phandle to the system I2C controller connected to that bus.
Control I/Os
------------
Many display panels can be controlled through pins driven by GPIOs. The nature
and timing of those control signals are device-specific and left for panel
device tree bindings to specify. The following GPIO specifiers can however be
used for panels that implement compatible control signals.
- enable-gpios: Specifier for a GPIO connected to the panel enable control
signal. The enable signal is active high and enables operation of the panel.
This property can also be used for panels implementing an active low power
down signal, which is a negated version of the enable signal. Active low
enable signals (or active high power down signals) can be supported by
inverting the GPIO specifier polarity flag.
Note that the enable signal control panel operation only and must not be
confused with a backlight enable signal.
- reset-gpios: Specifier for a GPIO coonnected to the panel reset control
signal. The reset signal is active low and resets the panel internal logic
while active. Active high reset signals can be supported by inverting the
GPIO specifier polarity flag.
Backlight
---------
Most display panels include a backlight. Some of them also include a backlight
controller exposed through a control bus such as I2C or DSI. Others expose
backlight control through GPIO, PWM or other signals connected to an external
backlight controller.
- backlight: For panels whose backlight is controlled by an external backlight
controller, this property contains a phandle that references the controller.
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment