ARM: dts: qcom: Add led and gpio-button nodes to ipq8064 boards

Add the dt nodes for enabling the leds and gpio-buttons.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

arch/arm/boot/dts/qcom-ipq8064-ap148.dts

@@ -12,6 +12,14 @@ i2c4_pins: i2c4_pinmux {
 				function = "gsbi4";
 				bias-disable;
 			};
+
+			buttons_pins: buttons_pins {
+				mux {
+					pins = "gpio54", "gpio65";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
 		};
 
 		gsbi@16300000 {

arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi

 // SPDX-License-Identifier: GPL-2.0
 #include "qcom-ipq8064.dtsi"
+#include <dt-bindings/input/input.h>
 
 / {
 	model = "Qualcomm Technologies, Inc. IPQ8064-v1.0";
@@ -63,5 +64,64 @@ sata@29000000 {
 			ports-implemented = <0x1>;
 			status = "ok";
 		};
+
+		gpio_keys {
+			compatible = "gpio-keys";
+			pinctrl-0 = <&buttons_pins>;
+			pinctrl-names = "default";
+
+			button@1 {
+				label = "reset";
+				linux,code = <KEY_RESTART>;
+				gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+				linux,input-type = <1>;
+				debounce-interval = <60>;
+			};
+			button@2 {
+				label = "wps";
+				linux,code = <KEY_WPS_BUTTON>;
+				gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+				linux,input-type = <1>;
+				debounce-interval = <60>;
+			};
+		};
+
+		leds {
+			compatible = "gpio-leds";
+			pinctrl-0 = <&leds_pins>;
+			pinctrl-names = "default";
+
+			led@7 {
+				label = "led_usb1";
+				gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
+				linux,default-trigger = "usbdev";
+				default-state = "off";
+			};
+
+			led@8 {
+				label = "led_usb3";
+				gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
+				linux,default-trigger = "usbdev";
+				default-state = "off";
+			};
+
+			led@9 {
+				label = "status_led_fail";
+				gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
+				default-state = "off";
+			};
+
+			led@26 {
+				label = "sata_led";
+				gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
+				default-state = "off";
+			};
+
+			led@53 {
+				label = "status_led_pass";
+				gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
+				default-state = "off";
+			};
+		};
 	};
 };

arch/arm/boot/dts/qcom-ipq8064.dtsi

@@ -153,6 +153,25 @@ mux {
 					bias-none;
 				};
 			};
+
+			leds_pins: leds_pins {
+				mux {
+					pins = "gpio7", "gpio8", "gpio9",
+					       "gpio26", "gpio53";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-down;
+					output-low;
+				};
+			};
+
+			buttons_pins: buttons_pins {
+				mux {
+					pins = "gpio54";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
 		};
 
 		intc: interrupt-controller@2000000 {