Merge branch 'at86rf230-next'

Alexander Aring says:

====================
at86rf230 cleanup

this is the first patch series to cleanup the at86rf230 driver. Later I want
to implement regmap and a asynchron spi handling for transmit and receiving
frames.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/ieee802154/at86rf230.txt

+* AT86RF230 IEEE 802.15.4 *
+
+Required properties:
+  - compatible:		should be "atmel,at86rf230", "atmel,at86rf231",
+			"atmel,at86rf233" or "atmel,at86rf212"
+  - spi-max-frequency:	maximal bus speed, should be set to 7500000 depends
+			sync or async operation mode
+  - reg:		the chipselect index
+  - interrupts:		the interrupt generated by the device
+
+Optional properties:
+  - reset-gpio:		GPIO spec for the rstn pin
+  - sleep-gpio:		GPIO spec for the slp_tr pin
+
+Example:
+
+	at86rf231@0 {
+		compatible = "atmel,at86rf231";
+		spi-max-frequency = <7500000>;
+		reg = <0>;
+		interrupts = <19 1>;
+		interrupt-parent = <&gpio3>;
+	};

drivers/net/ieee802154/at86rf230.c

@@ -23,6 +23,7 @@
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/interrupt.h>
+#include <linux/irq.h>
 #include <linux/gpio.h>
 #include <linux/delay.h>
 #include <linux/mutex.h>
@@ -692,10 +693,7 @@ at86rf230_xmit(struct ieee802154_dev *dev, struct sk_buff *skb)
 	if (rc < 0)
 		goto err_rx;
 
-	rc = at86rf230_start(dev);
-
-	return rc;
-
+	return at86rf230_start(dev);
 err_rx:
 	at86rf230_start(dev);
 err:
@@ -963,33 +961,24 @@ static irqreturn_t at86rf230_isr_level(int irq, void *data)
 	return at86rf230_isr(irq, data);
 }
 
-static int at86rf230_irq_polarity(struct at86rf230_local *lp, int pol)
-{
-	return at86rf230_write_subreg(lp, SR_IRQ_POLARITY, pol);
-}
-
 static int at86rf230_hw_init(struct at86rf230_local *lp)
 {
-	struct at86rf230_platform_data *pdata = lp->spi->dev.platform_data;
-	int rc, irq_pol;
-	u8 status;
+	int rc, irq_pol, irq_type;
+	u8 dvdd;
 	u8 csma_seed[2];
 
-	rc = at86rf230_read_subreg(lp, SR_TRX_STATUS, &status);
-	if (rc)
-		return rc;
-
 	rc = at86rf230_write_subreg(lp, SR_TRX_CMD, STATE_FORCE_TRX_OFF);
 	if (rc)
 		return rc;
 
+	irq_type = irq_get_trigger_type(lp->spi->irq);
 	/* configure irq polarity, defaults to high active */
-	if (pdata->irq_type & (IRQF_TRIGGER_FALLING | IRQF_TRIGGER_LOW))
+	if (irq_type & (IRQF_TRIGGER_FALLING | IRQF_TRIGGER_LOW))
 		irq_pol = IRQ_ACTIVE_LOW;
 	else
 		irq_pol = IRQ_ACTIVE_HIGH;
 
-	rc = at86rf230_irq_polarity(lp, irq_pol);
+	rc = at86rf230_write_subreg(lp, SR_IRQ_POLARITY, irq_pol);
 	if (rc)
 		return rc;
 
@@ -1017,10 +1006,10 @@ static int at86rf230_hw_init(struct at86rf230_local *lp)
 	/* Wait the next SLEEP cycle */
 	msleep(100);
 
-	rc = at86rf230_read_subreg(lp, SR_DVDD_OK, &status);
+	rc = at86rf230_read_subreg(lp, SR_DVDD_OK, &dvdd);
 	if (rc)
 		return rc;
-	if (!status) {
+	if (!dvdd) {
 		dev_err(&lp->spi->dev, "DVDD error\n");
 		return -EINVAL;
 	}
@@ -1032,7 +1021,6 @@ static struct at86rf230_platform_data *
 at86rf230_get_pdata(struct spi_device *spi)
 {
 	struct at86rf230_platform_data *pdata;
-	const char *irq_type;
 
 	if (!IS_ENABLED(CONFIG_OF) || !spi->dev.of_node)
 		return spi->dev.platform_data;
@@ -1044,19 +1032,6 @@ at86rf230_get_pdata(struct spi_device *spi)
 	pdata->rstn = of_get_named_gpio(spi->dev.of_node, "reset-gpio", 0);
 	pdata->slp_tr = of_get_named_gpio(spi->dev.of_node, "sleep-gpio", 0);
 
-	pdata->irq_type = IRQF_TRIGGER_RISING;
-	of_property_read_string(spi->dev.of_node, "irq-type", &irq_type);
-	if (!strcmp(irq_type, "level-high"))
-		pdata->irq_type = IRQF_TRIGGER_HIGH;
-	else if (!strcmp(irq_type, "level-low"))
-		pdata->irq_type = IRQF_TRIGGER_LOW;
-	else if (!strcmp(irq_type, "edge-rising"))
-		pdata->irq_type = IRQF_TRIGGER_RISING;
-	else if (!strcmp(irq_type, "edge-falling"))
-		pdata->irq_type = IRQF_TRIGGER_FALLING;
-	else
-		dev_warn(&spi->dev, "wrong irq-type specified using edge-rising\n");
-
 	spi->dev.platform_data = pdata;
 done:
 	return pdata;
@@ -1071,7 +1046,7 @@ static int at86rf230_probe(struct spi_device *spi)
 	u8 part = 0, version = 0, status;
 	irq_handler_t irq_handler;
 	work_func_t irq_worker;
-	int rc;
+	int rc, irq_type;
 	const char *chip;
 	struct ieee802154_ops *ops = NULL;
 
@@ -1087,27 +1062,17 @@ static int at86rf230_probe(struct spi_device *spi)
 	}
 
 	if (gpio_is_valid(pdata->rstn)) {
-		rc = gpio_request(pdata->rstn, "rstn");
+		rc = devm_gpio_request_one(&spi->dev, pdata->rstn,
+					   GPIOF_OUT_INIT_HIGH, "rstn");
 		if (rc)
 			return rc;
 	}
 
 	if (gpio_is_valid(pdata->slp_tr)) {
-		rc = gpio_request(pdata->slp_tr, "slp_tr");
-		if (rc)
-			goto err_slp_tr;
-	}
-
-	if (gpio_is_valid(pdata->rstn)) {
-		rc = gpio_direction_output(pdata->rstn, 1);
-		if (rc)
-			goto err_gpio_dir;
-	}
-
-	if (gpio_is_valid(pdata->slp_tr)) {
-		rc = gpio_direction_output(pdata->slp_tr, 0);
+		rc = devm_gpio_request_one(&spi->dev, pdata->slp_tr,
+					   GPIOF_OUT_INIT_LOW, "slp_tr");
 		if (rc)
-			goto err_gpio_dir;
+			return rc;
 	}
 
 	/* Reset */
@@ -1121,13 +1086,12 @@ static int at86rf230_probe(struct spi_device *spi)
 
 	rc = __at86rf230_detect_device(spi, &man_id, &part, &version);
 	if (rc < 0)
-		goto err_gpio_dir;
+		return rc;
 
 	if (man_id != 0x001f) {
 		dev_err(&spi->dev, "Non-Atmel dev found (MAN_ID %02x %02x)\n",
 			man_id >> 8, man_id & 0xFF);
-		rc = -EINVAL;
-		goto err_gpio_dir;
+		return -EINVAL;
 	}
 
 	switch (part) {
@@ -1154,16 +1118,12 @@ static int at86rf230_probe(struct spi_device *spi)
 	}
 
 	dev_info(&spi->dev, "Detected %s chip version %d\n", chip, version);
-	if (!ops) {
-		rc = -ENOTSUPP;
-		goto err_gpio_dir;
-	}
+	if (!ops)
+		return -ENOTSUPP;
 
 	dev = ieee802154_alloc_device(sizeof(*lp), ops);
-	if (!dev) {
-		rc = -ENOMEM;
-		goto err_gpio_dir;
-	}
+	if (!dev)
+		return -ENOMEM;
 
 	lp = dev->priv;
 	lp->dev = dev;
@@ -1176,7 +1136,8 @@ static int at86rf230_probe(struct spi_device *spi)
 	dev->extra_tx_headroom = 0;
 	dev->flags = IEEE802154_HW_OMIT_CKSUM | IEEE802154_HW_AACK;
 
-	if (pdata->irq_type & (IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING)) {
+	irq_type = irq_get_trigger_type(spi->irq);
+	if (irq_type & (IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING)) {
 		irq_worker = at86rf230_irqwork;
 		irq_handler = at86rf230_isr;
 	} else {
@@ -1202,75 +1163,65 @@ static int at86rf230_probe(struct spi_device *spi)
 	if (rc)
 		goto err_hw_init;
 
-	rc = request_irq(spi->irq, irq_handler,
-			 IRQF_SHARED | pdata->irq_type,
-			 dev_name(&spi->dev), lp);
+	/* Read irq status register to reset irq line */
+	rc = at86rf230_read_subreg(lp, RG_IRQ_STATUS, 0xff, 0, &status);
 	if (rc)
 		goto err_hw_init;
 
-	/* Read irq status register to reset irq line */
-	rc = at86rf230_read_subreg(lp, RG_IRQ_STATUS, 0xff, 0, &status);
+	rc = devm_request_irq(&spi->dev, spi->irq, irq_handler, IRQF_SHARED,
+			      dev_name(&spi->dev), lp);
 	if (rc)
-		goto err_irq;
+		goto err_hw_init;
 
 	rc = ieee802154_register_device(lp->dev);
 	if (rc)
-		goto err_irq;
+		goto err_hw_init;
 
 	return rc;
 
-err_irq:
-	free_irq(spi->irq, lp);
 err_hw_init:
 	flush_work(&lp->irqwork);
-	spi_set_drvdata(spi, NULL);
 	mutex_destroy(&lp->bmux);
 	ieee802154_free_device(lp->dev);
 
-err_gpio_dir:
-	if (gpio_is_valid(pdata->slp_tr))
-		gpio_free(pdata->slp_tr);
-err_slp_tr:
-	if (gpio_is_valid(pdata->rstn))
-		gpio_free(pdata->rstn);
 	return rc;
 }
 
 static int at86rf230_remove(struct spi_device *spi)
 {
 	struct at86rf230_local *lp = spi_get_drvdata(spi);
-	struct at86rf230_platform_data *pdata = spi->dev.platform_data;
 
 	/* mask all at86rf230 irq's */
 	at86rf230_write_subreg(lp, SR_IRQ_MASK, 0);
 	ieee802154_unregister_device(lp->dev);
-
-	free_irq(spi->irq, lp);
 	flush_work(&lp->irqwork);
-
-	if (gpio_is_valid(pdata->slp_tr))
-		gpio_free(pdata->slp_tr);
-	if (gpio_is_valid(pdata->rstn))
-		gpio_free(pdata->rstn);
-
 	mutex_destroy(&lp->bmux);
 	ieee802154_free_device(lp->dev);
-
 	dev_dbg(&spi->dev, "unregistered at86rf230\n");
+
 	return 0;
 }
 
-#if IS_ENABLED(CONFIG_OF)
-static struct of_device_id at86rf230_of_match[] = {
+static const struct of_device_id at86rf230_of_match[] = {
 	{ .compatible = "atmel,at86rf230", },
 	{ .compatible = "atmel,at86rf231", },
 	{ .compatible = "atmel,at86rf233", },
 	{ .compatible = "atmel,at86rf212", },
 	{ },
 };
-#endif
+MODULE_DEVICE_TABLE(of, at86rf230_of_match);
+
+static const struct spi_device_id at86rf230_device_id[] = {
+	{ .name = "at86rf230", },
+	{ .name = "at86rf231", },
+	{ .name = "at86rf233", },
+	{ .name = "at86rf212", },
+	{ },
+};
+MODULE_DEVICE_TABLE(spi, at86rf230_device_id);
 
 static struct spi_driver at86rf230_driver = {
+	.id_table = at86rf230_device_id,
 	.driver = {
 		.of_match_table = of_match_ptr(at86rf230_of_match),
 		.name	= "at86rf230",

include/linux/spi/at86rf230.h

@@ -26,20 +26,6 @@ struct at86rf230_platform_data {
 	int rstn;
 	int slp_tr;
 	int dig2;
-
-	/* Setting the irq_type will configure the driver to request
-	 * the platform irq trigger type according to the given value
-	 * and configure the interrupt polarity of the device to the
-	 * corresponding polarity.
-	 *
-	 * Allowed values are: IRQF_TRIGGER_RISING, IRQF_TRIGGER_FALLING,
-	 *                     IRQF_TRIGGER_HIGH and IRQF_TRIGGER_LOW
-	 *
-	 * Setting it to 0, the driver does not touch the trigger type
-	 * configuration of the interrupt and sets the interrupt polarity
-	 * of the device to high active (the default value).
-	 */
-	int irq_type;
 };
 
 #endif