[PATCH] Improve PA-RISC make configcheck

Fix "make configcheck | fgrep 'not needed' | fgrep parisc"
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

arch/parisc/kernel/binfmt_elf32.c

@@ -37,7 +37,6 @@ typedef unsigned int elf_greg_t;
 #include <linux/spinlock.h>
 #include <asm/processor.h>
 #include <linux/module.h>
-#include <linux/config.h>
 #include <linux/elfcore.h>
 #include <linux/compat.h>		/* struct compat_timeval */
 

arch/parisc/kernel/perf.c

@@ -42,7 +42,6 @@
  *  on every box. 
  */
 
-#include <linux/config.h>
 #include <linux/init.h>
 #include <linux/proc_fs.h>
 #include <linux/miscdevice.h>

arch/parisc/kernel/signal32.c

@@ -20,7 +20,6 @@
  *    Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
  */
 
-#include <linux/config.h>
 #include <linux/compat.h>
 #include <linux/slab.h>
 #include <linux/module.h>

arch/parisc/math-emu/driver.c

@@ -27,7 +27,6 @@
  *  Copyright (C) 2001	      Hewlett-Packard <bame@debian.org>
  */
 
-#include <linux/config.h>
 #include <linux/sched.h>
 #include "float.h"
 #include "math-emu.h"

drivers/parisc/eisa_eeprom.c

@@ -19,7 +19,6 @@
  *    Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
  */
 
-#include <linux/config.h>
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/kernel.h>

drivers/parisc/hppb.c

@@ -16,7 +16,6 @@
 **
 */
 
-#include <linux/config.h>
 #include <linux/types.h>
 #include <linux/init.h>
 #include <linux/mm.h>

include/asm-parisc/ide.h

@@ -13,8 +13,6 @@
 
 #ifdef __KERNEL__
 
-#include <linux/config.h>
-
 #ifndef MAX_HWIFS
 #define MAX_HWIFS	2
 #endif

include/asm-parisc/numnodes.h

 #ifndef _ASM_MAX_NUMNODES_H
 #define _ASM_MAX_NUMNODES_H
 
-#include <linux/config.h>
-
 /* Max 8 Nodes */
 #define NODES_SHIFT	3
 

include/asm-parisc/serial.h

@@ -2,8 +2,6 @@
  * include/asm-parisc/serial.h
  */
 
-#include <linux/config.h>
-
 /*
  * This assumes you have a 7.272727 MHz clock for your UART.
  * The documentation implies a 40Mhz clock, and elsewhere a 7Mhz clock