Merge branch 'net-phy-at803x-device-tree-binding'

Michael Walle says:

====================
net: phy: at803x device tree binding

Adds a device tree binding to configure the clock and the RGMII voltage.

Changes since v1:
 - rebased to latest net-next
 - renamed "Atheros" to "Qualcomm Atheros"
 - add a new patch to remove config_init() from AR9331

Changes since the RFC:
 - renamed the Kconfig entry to "Qualcomm Atheros.." and reordered the
   item
 - renamed the prefix from atheros to qca
 - use the correct name AR803x (instead of AT803x) in new files and
   dt-bindings.
 - listed the PHY maintainers in the new schema. Hopefully, thats ok.
 - fixed a typo in the bindings schema
 - run dtb_checks and dt_binding_check and fixed the schema
 - dropped the rgmii-io-1v8 property; instead provide two regulators vddh
   and vddio, add one consumer vddio-supply
 - fix the clock settings for the AR8030/AR8035
 - only the AR8031 supports chaning the LDO and the PLL mode in software.
   Check if we have the correct PHY.
 - new patch to mention the AR8033 which is the same as the AR8031 just
   without PTP support
 - new patch which corrects any displayed PHY names and comments. Be
   consistent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/qca,ar803x.yaml

+# SPDX-License-Identifier: GPL-2.0+
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/qca,ar803x.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Atheros AR803x PHY
+
+maintainers:
+  - Andrew Lunn <andrew@lunn.ch>
+  - Florian Fainelli <f.fainelli@gmail.com>
+  - Heiner Kallweit <hkallweit1@gmail.com>
+
+description: |
+  Bindings for Qualcomm Atheros AR803x PHYs
+
+allOf:
+  - $ref: ethernet-phy.yaml#
+
+properties:
+  qca,clk-out-frequency:
+    description: Clock output frequency in Hertz.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [ 25000000, 50000000, 62500000, 125000000 ]
+
+  qca,clk-out-strength:
+    description: Clock output driver strength.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [ 0, 1, 2 ]
+
+  qca,keep-pll-enabled:
+    description: |
+      If set, keep the PLL enabled even if there is no link. Useful if you
+      want to use the clock output without an ethernet link.
+
+      Only supported on the AR8031.
+    type: boolean
+
+  vddio-supply:
+    description: |
+      RGMII I/O voltage regulator (see regulator/regulator.yaml).
+
+      The PHY supports RGMII I/O voltages of 1.5V, 1.8V and 2.5V. You can
+      either connect this to the vddio-regulator (1.5V / 1.8V) or the
+      vddh-regulator (2.5V).
+
+      Only supported on the AR8031.
+
+  vddio-regulator:
+    type: object
+    description:
+      Initial data for the VDDIO regulator. Set this to 1.5V or 1.8V.
+    allOf:
+      - $ref: /schemas/regulator/regulator.yaml
+
+  vddh-regulator:
+    type: object
+    description:
+      Dummy subnode to model the external connection of the PHY VDDH
+      regulator to VDDIO.
+    allOf:
+      - $ref: /schemas/regulator/regulator.yaml
+
+
+examples:
+  - |
+    #include <dt-bindings/net/qca-ar803x.h>
+
+    ethernet {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        phy-mode = "rgmii-id";
+
+        ethernet-phy@0 {
+            reg = <0>;
+
+            qca,clk-out-frequency = <125000000>;
+            qca,clk-out-strength = <AR803X_STRENGTH_FULL>;
+
+            vddio-supply = <&vddio>;
+
+            vddio: vddio-regulator {
+                regulator-min-microvolt = <1800000>;
+                regulator-max-microvolt = <1800000>;
+            };
+        };
+    };
+  - |
+    #include <dt-bindings/net/qca-ar803x.h>
+
+    ethernet {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        phy-mode = "rgmii-id";
+
+        ethernet-phy@0 {
+            reg = <0>;
+
+            qca,clk-out-frequency = <50000000>;
+            qca,keep-pll-enabled;
+
+            vddio-supply = <&vddh>;
+
+            vddh: vddh-regulator {
+            };
+        };
+    };

MAINTAINERS

@@ -6155,10 +6155,12 @@ S:	Maintained
 F:	Documentation/ABI/testing/sysfs-class-net-phydev
 F:	Documentation/devicetree/bindings/net/ethernet-phy.yaml
 F:	Documentation/devicetree/bindings/net/mdio*
+F:	Documentation/devicetree/bindings/net/qca,ar803x.yaml
 F:	Documentation/networking/phy.rst
 F:	drivers/net/phy/
 F:	drivers/of/of_mdio.c
 F:	drivers/of/of_net.c
+F:	include/dt-bindings/net/qca-ar803x.h
 F:	include/linux/*mdio*.h
 F:	include/linux/of_net.h
 F:	include/linux/phy.h

drivers/net/phy/Kconfig

@@ -282,11 +282,6 @@ config AX88796B_PHY
 	  Currently supports the Asix Electronics PHY found in the X-Surf 100
 	  AX88796B package.
 
-config AT803X_PHY
-	tristate "AT803X PHYs"
-	---help---
-	  Currently supports the AT8030 and AT8035 model
-
 config BCM63XX_PHY
 	tristate "Broadcom 63xx SOCs internal PHY"
 	depends on BCM63XX || COMPILE_TEST
@@ -444,6 +439,11 @@ config NXP_TJA11XX_PHY
 	---help---
 	  Currently supports the NXP TJA1100 and TJA1101 PHY.
 
+config AT803X_PHY
+	tristate "Qualcomm Atheros AR803X PHYs"
+	help
+	  Currently supports the AR8030, AR8031, AR8033 and AR8035 model
+
 config QSEMI_PHY
 	tristate "Quality Semiconductor PHYs"
 	---help---

include/dt-bindings/net/qca-ar803x.h

+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Device Tree constants for the Qualcomm Atheros AR803x PHYs
+ */
+
+#ifndef _DT_BINDINGS_QCA_AR803X_H
+#define _DT_BINDINGS_QCA_AR803X_H
+
+#define AR803X_STRENGTH_FULL		0
+#define AR803X_STRENGTH_HALF		1
+#define AR803X_STRENGTH_QUARTER		2
+
+#endif