Commit 19b0fa11 authored by Peter Ujfalusi's avatar Peter Ujfalusi Committed by Mark Brown

ASoC: tlv320aic3x: Support for OCMV configuration

In aic3x class of devices Output Common-Mode Voltage can be configured for
better analog performance.
The OCMV value depends on the Analog and digital domain power supply
voltage configuration.

The default OCMV of 1.35V gives best performance when AVDD is around 2.7V
and DVDD is 1.525V, but for higher AVDD/DVDD higher OCMV setting is
recommended.

The patch gives an automatic way of guessing the best OCMV which can be
overwritten by a DT parameter if needed.
Signed-off-by: default avatarPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: default avatarMark Brown <broonie@kernel.org>
parent 5771a8c0
......@@ -26,6 +26,11 @@ Optional properties:
3 - MICBIAS output is connected to AVDD,
If this node is not mentioned or if the value is incorrect, then MicBias
is powered down.
- ai3x-ocmv - Output Common-Mode Voltage selection:
0 - 1.35V,
1 - 1.5V,
2 - 1.65V,
3 - 1.8V
- AVDD-supply, IOVDD-supply, DRVDD-supply, DVDD-supply : power supplies for the
device as covered in Documentation/devicetree/bindings/regulator/regulator.txt
......
......@@ -93,6 +93,8 @@ struct aic3x_priv {
/* Selects the micbias voltage */
enum aic3x_micbias_voltage micbias_vg;
/* Output Common-Mode Voltage */
u8 ocmv;
};
static const struct reg_default aic3x_reg[] = {
......@@ -1572,6 +1574,10 @@ static int aic3x_init(struct snd_soc_codec *codec)
break;
}
/* Output common-mode voltage = 1.5 V */
snd_soc_update_bits(codec, HPOUT_SC, HPOUT_SC_OCMV_MASK,
aic3x->ocmv << HPOUT_SC_OCMV_SHIFT);
return 0;
}
......@@ -1699,6 +1705,43 @@ static struct snd_soc_codec_driver soc_codec_dev_aic3x = {
},
};
static void aic3x_configure_ocmv(struct i2c_client *client)
{
struct device_node *np = client->dev.of_node;
struct aic3x_priv *aic3x = i2c_get_clientdata(client);
u32 value;
int dvdd, avdd;
if (np && !of_property_read_u32(np, "ai3x-ocmv", &value)) {
/* OCMV setting is forced by DT */
if (value <= 3) {
aic3x->ocmv = value;
return;
}
}
dvdd = regulator_get_voltage(aic3x->supplies[1].consumer);
avdd = regulator_get_voltage(aic3x->supplies[2].consumer);
if (avdd > 3600000 || dvdd > 1950000) {
dev_warn(&client->dev,
"Too high supply voltage(s) AVDD: %d, DVDD: %d\n",
avdd, dvdd);
} else if (avdd == 3600000 && dvdd == 1950000) {
aic3x->ocmv = HPOUT_SC_OCMV_1_8V;
} else if (avdd > 3300000 && dvdd > 1800000) {
aic3x->ocmv = HPOUT_SC_OCMV_1_65V;
} else if (avdd > 3000000 && dvdd > 1650000) {
aic3x->ocmv = HPOUT_SC_OCMV_1_5V;
} else if (avdd >= 2700000 && dvdd >= 1525000) {
aic3x->ocmv = HPOUT_SC_OCMV_1_35V;
} else {
dev_warn(&client->dev,
"Invalid supply voltage(s) AVDD: %d, DVDD: %d\n",
avdd, dvdd);
}
}
/*
* AIC3X 2 wire address can be up to 4 devices with device addresses
* 0x18, 0x19, 0x1A, 0x1B
......@@ -1816,6 +1859,8 @@ static int aic3x_i2c_probe(struct i2c_client *i2c,
goto err_gpio;
}
aic3x_configure_ocmv(i2c);
if (aic3x->model == AIC3X_MODEL_3007) {
ret = regmap_register_patch(aic3x->regmap, aic3007_class_d,
ARRAY_SIZE(aic3007_class_d));
......
......@@ -243,6 +243,14 @@
#define MICBIAS_LEVEL_SHIFT (6)
#define MICBIAS_LEVEL_MASK (3 << 6)
/* HPOUT_SC */
#define HPOUT_SC_OCMV_MASK (3 << 6)
#define HPOUT_SC_OCMV_SHIFT (6)
#define HPOUT_SC_OCMV_1_35V 0
#define HPOUT_SC_OCMV_1_5V 1
#define HPOUT_SC_OCMV_1_65V 2
#define HPOUT_SC_OCMV_1_8V 3
/* headset detection / button API */
/* The AIC3x supports detection of stereo headsets (GND + left + right signal)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment