Commit 1ac71ec0 authored by Tudor Ambarus's avatar Tudor Ambarus

mtd: spi-nor: Fix SPI NOR acronym

The correct terminology is serial NOR flash or SPI NOR.
s/SPI-NOR/SPI NOR and s/spi-nor/SPI NOR across the subsystem.
Signed-off-by: default avatarTudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: default avatarSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
parent 075fd6df
# SPDX-License-Identifier: GPL-2.0-only
menuconfig MTD_SPI_NOR
tristate "SPI-NOR device support"
tristate "SPI NOR device support"
depends on MTD
depends on MTD && SPI_MASTER
select SPI_MEM
help
This is the framework for the SPI NOR which can be used by the SPI
device drivers and the SPI-NOR device driver.
device drivers and the SPI NOR device driver.
if MTD_SPI_NOR
......
......@@ -21,11 +21,11 @@ config SPI_CADENCE_QUADSPI
Flash as an MTD device.
config SPI_HISI_SFC
tristate "Hisilicon FMC SPI-NOR Flash Controller(SFC)"
tristate "Hisilicon FMC SPI NOR Flash Controller(SFC)"
depends on ARCH_HISI || COMPILE_TEST
depends on HAS_IOMEM
help
This enables support for HiSilicon FMC SPI-NOR flash controller.
This enables support for HiSilicon FMC SPI NOR flash controller.
config SPI_NXP_SPIFI
tristate "NXP SPI Flash Interface (SPIFI)"
......
......@@ -727,7 +727,7 @@ static int aspeed_smc_chip_setup_finish(struct aspeed_smc_chip *chip)
/*
* TODO: Adjust clocks if fast read is supported and interpret
* SPI-NOR flags to adjust controller settings.
* SPI NOR flags to adjust controller settings.
*/
if (chip->nor.read_proto == SNOR_PROTO_1_1_1) {
if (chip->nor.read_dummy == 0)
......
// SPDX-License-Identifier: GPL-2.0-or-later
/*
* HiSilicon FMC SPI-NOR flash controller driver
* HiSilicon FMC SPI NOR flash controller driver
*
* Copyright (c) 2015-2016 HiSilicon Technologies Co., Ltd.
*/
......
// SPDX-License-Identifier: GPL-2.0-only
/*
* SPI-NOR driver for NXP SPI Flash Interface (SPIFI)
* SPI NOR driver for NXP SPI Flash Interface (SPIFI)
*
* Copyright (C) 2015 Joachim Eastwood <manabian@gmail.com>
*
......
......@@ -2469,7 +2469,7 @@ static int spi_nor_select_read(struct spi_nor *nor,
nor->read_proto = read->proto;
/*
* In the spi-nor framework, we don't need to make the difference
* In the SPI NOR framework, we don't need to make the difference
* between mode clock cycles and wait state clock cycles.
* Indeed, the value of the mode clock cycles is used by a QSPI
* flash memory to know whether it should enter or leave its 0-4-4
......@@ -3126,7 +3126,7 @@ int spi_nor_scan(struct spi_nor *nor, const char *name,
/*
* Make sure the XSR_RDY flag is set before calling
* spi_nor_wait_till_ready(). Xilinx S3AN share MFR
* with Atmel spi-nor
* with Atmel SPI NOR.
*/
if (info->flags & SPI_NOR_XSR_RDY)
nor->flags |= SNOR_F_READY_XSR_RDY;
......
......@@ -302,7 +302,7 @@ struct spi_nor;
* @read: read data from the SPI NOR.
* @write: write data to the SPI NOR.
* @erase: erase a sector of the SPI NOR at the offset @offs; if
* not provided by the driver, spi-nor will send the erase
* not provided by the driver, SPI NOR will send the erase
* opcode via write_reg().
*/
struct spi_nor_controller_ops {
......@@ -336,7 +336,7 @@ struct spi_nor_flash_parameter;
* layer is not DMA-able
* @bouncebuf_size: size of the bounce buffer
* @info: SPI NOR part JEDEC MFR ID and other info
* @manufacturer: spi-nor manufacturer
* @manufacturer: SPI NOR manufacturer
* @page_size: the page size of the SPI NOR
* @addr_width: number of address bytes
* @erase_opcode: the opcode for erasing a sector
......@@ -344,12 +344,12 @@ struct spi_nor_flash_parameter;
* @read_dummy: the dummy needed by the read operation
* @program_opcode: the program opcode
* @sst_write_second: used by the SST write operation
* @flags: flag options for the current SPI-NOR (SNOR_F_*)
* @flags: flag options for the current SPI NOR (SNOR_F_*)
* @read_proto: the SPI protocol for read operations
* @write_proto: the SPI protocol for write operations
* @reg_proto: the SPI protocol for read_reg/write_reg/erase operations
* @controller_ops: SPI NOR controller driver specific operations.
* @params: [FLASH-SPECIFIC] SPI-NOR flash parameters and settings.
* @params: [FLASH-SPECIFIC] SPI NOR flash parameters and settings.
* The structure includes legacy flash parameters and
* settings that can be overwritten by the spi_nor_fixups
* hooks, or dynamically when parsing the SFDP tables.
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment