Commit 1cf86bc2 authored by Douglas Anderson's avatar Douglas Anderson Committed by Linus Walleij

pinctrl: qcom: spmi-gpio: Fix pmic_gpio_config_get() to be compliant

If you do this on an sdm845 board:
  grep "" /sys/kernel/debug/pinctrl/*spmi:pmic*/pinconf-groups

...it looks like nonsense.  For every pin you see listed:
  input bias disabled, input bias high impedance, input bias pull down, input bias pull up, ...

That's because pmic_gpio_config_get() isn't complying with the rules
that pinconf_generic_dump_one() expects.  Specifically for boolean
parameters (anything with a "struct pin_config_item" where has_arg is
false) the function expects that the function should return its value
not through the "config" parameter but should return "0" if the value
is set and "-EINVAL" if the value isn't set.

Let's fix this.

From a quick sample of other pinctrl drivers, it appears to be
tradition to also return 1 through the config parameter for these
boolean parameters when they exist.  I'm not one to knock tradition,
so I'll follow tradition and return 1 in these cases.  While I'm at
it, I'll also continue searching for four leaf clovers, kocking on
wood three times, and trying not to break mirrors.

NOTE: This also fixes an apparent typo for reading
PIN_CONFIG_BIAS_DISABLE where the old driver was accidentally
using "=" instead of "==" and thus was setting some internal
state when you tried to query PIN_CONFIG_BIAS_DISABLE.  Oops.

Fixes: eadff302 ("pinctrl: Qualcomm SPMI PMIC GPIO pin controller driver")
Signed-off-by: default avatarDouglas Anderson <dianders@chromium.org>
Signed-off-by: default avatarLinus Walleij <linus.walleij@linaro.org>
parent 05e0c828
......@@ -390,31 +390,47 @@ static int pmic_gpio_config_get(struct pinctrl_dev *pctldev,
switch (param) {
case PIN_CONFIG_DRIVE_PUSH_PULL:
arg = pad->buffer_type == PMIC_GPIO_OUT_BUF_CMOS;
if (pad->buffer_type != PMIC_GPIO_OUT_BUF_CMOS)
return -EINVAL;
arg = 1;
break;
case PIN_CONFIG_DRIVE_OPEN_DRAIN:
arg = pad->buffer_type == PMIC_GPIO_OUT_BUF_OPEN_DRAIN_NMOS;
if (pad->buffer_type != PMIC_GPIO_OUT_BUF_OPEN_DRAIN_NMOS)
return -EINVAL;
arg = 1;
break;
case PIN_CONFIG_DRIVE_OPEN_SOURCE:
arg = pad->buffer_type == PMIC_GPIO_OUT_BUF_OPEN_DRAIN_PMOS;
if (pad->buffer_type != PMIC_GPIO_OUT_BUF_OPEN_DRAIN_PMOS)
return -EINVAL;
arg = 1;
break;
case PIN_CONFIG_BIAS_PULL_DOWN:
arg = pad->pullup == PMIC_GPIO_PULL_DOWN;
if (pad->pullup != PMIC_GPIO_PULL_DOWN)
return -EINVAL;
arg = 1;
break;
case PIN_CONFIG_BIAS_DISABLE:
arg = pad->pullup = PMIC_GPIO_PULL_DISABLE;
if (pad->pullup != PMIC_GPIO_PULL_DISABLE)
return -EINVAL;
arg = 1;
break;
case PIN_CONFIG_BIAS_PULL_UP:
arg = pad->pullup == PMIC_GPIO_PULL_UP_30;
if (pad->pullup != PMIC_GPIO_PULL_UP_30)
return -EINVAL;
arg = 1;
break;
case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
arg = !pad->is_enabled;
if (pad->is_enabled)
return -EINVAL;
arg = 1;
break;
case PIN_CONFIG_POWER_SOURCE:
arg = pad->power_source;
break;
case PIN_CONFIG_INPUT_ENABLE:
arg = pad->input_enabled;
if (!pad->input_enabled)
return -EINVAL;
arg = 1;
break;
case PIN_CONFIG_OUTPUT:
arg = pad->out_value;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment