Merge git://linuxtv.org/sailus/media_tree into media_stage

* git://linuxtv.org/sailus/media_tree: (47 commits)
  media: i2c: ov4689: code cleanup
  media: ov9650: Drop platform data code path
  media: ov7670: Drop unused include
  media: ov2640: Drop legacy includes
  media: tc358746: add Toshiba TC358746 Parallel to CSI-2 bridge driver
  media: dt-bindings: add bindings for Toshiba TC358746
  phy: dphy: add support to calculate the timing based on hs_clk_rate
  phy: dphy: refactor get_default_config
  v4l: subdev: Warn if disabling streaming failed, return success
  dw9768: Enable low-power probe on ACPI
  media: i2c: imx290: Replace GAIN control with ANALOGUE_GAIN
  media: i2c: imx290: Add crop selection targets support
  media: i2c: imx290: Factor out format retrieval to separate function
  media: i2c: imx290: Move registers with fixed value to init array
  media: i2c: imx290: Create controls for fwnode properties
  media: i2c: imx290: Implement HBLANK and VBLANK controls
  media: i2c: imx290: Split control initialization to separate function
  media: i2c: imx290: Fix max gain value
  media: i2c: imx290: Add exposure time control
  media: i2c: imx290: Define more register macros
  ...

Documentation/devicetree/bindings/media/i2c/imx290.txt

-* Sony IMX290 1/2.8-Inch CMOS Image Sensor
-
-The Sony IMX290 is a 1/2.8-Inch CMOS Solid-state image sensor with
-Square Pixel for Color Cameras. It is programmable through I2C and 4-wire
-interfaces. The sensor output is available via CMOS logic parallel SDR output,
-Low voltage LVDS DDR output and CSI-2 serial data output. The CSI-2 bus is the
-default. No bindings have been defined for the other busses.
-
-Required Properties:
-- compatible: Should be "sony,imx290"
-- reg: I2C bus address of the device
-- clocks: Reference to the xclk clock.
-- clock-names: Should be "xclk".
-- clock-frequency: Frequency of the xclk clock in Hz.
-- vdddo-supply: Sensor digital IO regulator.
-- vdda-supply: Sensor analog regulator.
-- vddd-supply: Sensor digital core regulator.
-
-Optional Properties:
-- reset-gpios: Sensor reset GPIO
-
-The imx290 device node should contain one 'port' child node with
-an 'endpoint' subnode. For further reading on port node refer to
-Documentation/devicetree/bindings/media/video-interfaces.txt.
-
-Required Properties on endpoint:
-- data-lanes: check ../video-interfaces.txt
-- link-frequencies: check ../video-interfaces.txt
-- remote-endpoint: check ../video-interfaces.txt
-
-Example:
-	&i2c1 {
-		...
-		imx290: camera-sensor@1a {
-			compatible = "sony,imx290";
-			reg = <0x1a>;
-
-			reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&camera_rear_default>;
-
-			clocks = <&gcc GCC_CAMSS_MCLK0_CLK>;
-			clock-names = "xclk";
-			clock-frequency = <37125000>;
-
-			vdddo-supply = <&camera_vdddo_1v8>;
-			vdda-supply = <&camera_vdda_2v8>;
-			vddd-supply = <&camera_vddd_1v5>;
-
-			port {
-				imx290_ep: endpoint {
-					data-lanes = <1 2 3 4>;
-					link-frequencies = /bits/ 64 <445500000>;
-					remote-endpoint = <&csiphy0_ep>;
-				};
-			};
-		};

Documentation/devicetree/bindings/media/i2c/ovti,ov4689.yaml

+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/ovti,ov4689.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Omnivision OV4689 CMOS
+
+maintainers:
+  - Mikhail Rudenko <mike.rudenko@gmail.com>
+
+description: |
+  The Omnivision OV4689 is a high performance, 1/3-inch, 4 megapixel
+  image sensor. Ihis chip supports high frame rate speeds up to 90 fps
+  at 2688x1520 resolution. It is programmable through an I2C
+  interface, and sensor output is sent via 1/2/4 lane MIPI CSI-2
+  connection.
+
+allOf:
+  - $ref: /schemas/media/video-interface-devices.yaml#
+
+properties:
+  compatible:
+    const: ovti,ov4689
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    description:
+      External clock (XVCLK) for the sensor, 6-64 MHz
+    maxItems: 1
+
+  dovdd-supply:
+    description:
+      Digital I/O voltage supply, 1.7-3.0 V
+
+  avdd-supply:
+    description:
+      Analog voltage supply, 2.6-3.0 V
+
+  dvdd-supply:
+    description:
+      Digital core voltage supply, 1.1-1.3 V
+
+  powerdown-gpios:
+    description:
+      GPIO connected to the powerdown pin (active low)
+
+  reset-gpios:
+    maxItems: 1
+    description:
+      GPIO connected to the reset pin (active low)
+
+  orientation: true
+
+  rotation: true
+
+  port:
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    additionalProperties: false
+    description:
+      Output port node, single endpoint describing the CSI-2 transmitter
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          data-lanes:
+            oneOf:
+              - items:
+                  - const: 1
+                  - const: 2
+                  - const: 3
+                  - const: 4
+              - items:
+                  - const: 1
+                  - const: 2
+              - items:
+                  - const: 1
+          link-frequencies: true
+
+        required:
+          - data-lanes
+          - link-frequencies
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - dovdd-supply
+  - avdd-supply
+  - dvdd-supply
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ov4689: camera@36 {
+            compatible = "ovti,ov4689";
+            reg = <0x36>;
+
+            clocks = <&ov4689_clk>;
+
+            avdd-supply = <&ov4689_avdd>;
+            dovdd-supply = <&ov4689_dovdd>;
+            dvdd-supply = <&ov4689_dvdd>;
+
+            powerdown-gpios = <&pio 107 GPIO_ACTIVE_LOW>;
+            reset-gpios = <&pio 109 GPIO_ACTIVE_LOW>;
+
+            orientation = <2>;
+            rotation = <0>;
+
+            port {
+                wcam_out: endpoint {
+                    remote-endpoint = <&mipi_in_wcam>;
+                    data-lanes = <1 2 3 4>;
+                    link-frequencies = /bits/ 64 <504000000>;
+                };
+            };
+        };
+    };
+
+...

Documentation/devicetree/bindings/media/i2c/sony,imx290.yaml

+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/sony,imx290.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Sony IMX290 1/2.8-Inch CMOS Image Sensor
+
+maintainers:
+  - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+  - Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+
+description: |-
+  The Sony IMX290 is a 1/2.8-Inch CMOS Solid-state image sensor with Square
+  Pixel for Color Cameras. It is programmable through I2C and 4-wire
+  interfaces. The sensor output is available via CMOS logic parallel SDR
+  output, Low voltage LVDS DDR output and CSI-2 serial data output. The CSI-2
+  bus is the default. No bindings have been defined for the other busses.
+
+properties:
+  compatible:
+    enum:
+      - sony,imx290
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    description: Input clock (37.125 MHz or 74.25 MHz)
+    items:
+      - const: xclk
+
+  clock-frequency:
+    description: Frequency of the xclk clock in Hz
+
+  vdda-supply:
+    description: Analog power supply (2.9V)
+
+  vddd-supply:
+    description: Digital core power supply (1.2V)
+
+  vdddo-supply:
+    description: Digital I/O power supply (1.8V)
+
+  reset-gpios:
+    description: Sensor reset (XCLR) GPIO
+    maxItems: 1
+
+  port:
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    description: |
+      Video output port
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          data-lanes:
+            anyOf:
+              - items:
+                  - const: 1
+                  - const: 2
+              - items:
+                  - const: 1
+                  - const: 2
+                  - const: 3
+                  - const: 4
+
+          link-frequencies: true
+
+        required:
+          - data-lanes
+          - link-frequencies
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - clock-frequency
+  - vdda-supply
+  - vddd-supply
+  - vdddo-supply
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        imx290: camera-sensor@1a {
+            compatible = "sony,imx290";
+            reg = <0x1a>;
+
+            pinctrl-names = "default";
+            pinctrl-0 = <&camera_rear_default>;
+
+            clocks = <&gcc 90>;
+            clock-names = "xclk";
+            clock-frequency = <37125000>;
+
+            vdddo-supply = <&camera_vdddo_1v8>;
+            vdda-supply = <&camera_vdda_2v8>;
+            vddd-supply = <&camera_vddd_1v5>;
+
+            reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>;
+
+            port {
+                imx290_ep: endpoint {
+                    data-lanes = <1 2 3 4>;
+                    link-frequencies = /bits/ 64 <445500000>;
+                    remote-endpoint = <&csiphy0_ep>;
+                };
+            };
+        };
+    };
+...

Documentation/devicetree/bindings/media/i2c/st,st-vgxy61.yaml

+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+# Copyright (c) 2022 STMicroelectronics SA.
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/st,st-vgxy61.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectronics VGxy61 HDR Global Shutter Sensor Family Device Tree Bindings
+
+maintainers:
+  - Benjamin Mugnier <benjamin.mugnier@foss.st.com>
+  - Sylvain Petinot <sylvain.petinot@foss.st.com>
+
+description: |-
+  STMicroelectronics VGxy61 family has a CSI-2 output port. CSI-2 output is a
+  quad lanes 800Mbps per lane.
+  Supported formats are RAW8, RAW10, RAW12, RAW14 and RAW16.
+  Following part number are supported
+  - VG5661 and VG6661 are 1.6 Mpx (1464 x 1104) monochrome and color sensors.
+  Maximum frame rate is 75 fps.
+  - VG5761 and VG6761 are 2.3 Mpx (1944 x 1204) monochrome and color sensors.
+  Maximum frame rate is 60 fps.
+
+properties:
+  compatible:
+    const: st,st-vgxy61
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  VCORE-supply:
+    description:
+      Sensor digital core supply. Must be 1.2 volts.
+
+  VDDIO-supply:
+    description:
+      Sensor digital IO supply. Must be 1.8 volts.
+
+  VANA-supply:
+    description:
+      Sensor analog supply. Must be 2.8 volts.
+
+  reset-gpios:
+    description:
+      Reference to the GPIO connected to the reset pin, if any.
+      This is an active low signal to the vgxy61.
+
+  st,strobe-gpios-polarity:
+    description:
+      Invert polarity of illuminator's lights strobe GPIOs.
+      These GPIOs directly drive the illuminator LEDs.
+    type: boolean
+
+  port:
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    additionalProperties: false
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          data-lanes:
+            description:
+              CSI lanes to use
+            items:
+              - const: 1
+              - const: 2
+              - const: 3
+              - const: 4
+
+          remote-endpoint: true
+
+        required:
+          - data-lanes
+
+required:
+  - compatible
+  - clocks
+  - VCORE-supply
+  - VDDIO-supply
+  - VANA-supply
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        vgxy61: csi2tx@10 {
+            compatible = "st,st-vgxy61";
+            reg = <0x10>;
+            clocks = <&clk_ext_camera>;
+            VCORE-supply = <&v1v2>;
+            VDDIO-supply = <&v1v8>;
+            VANA-supply = <&v2v8>;
+            reset-gpios = <&mfxgpio 18 GPIO_ACTIVE_LOW>;
+            port {
+                ep0: endpoint {
+                    data-lanes = <1 2 3 4>;
+                    remote-endpoint = <&mipi_csi2_out>;
+                };
+            };
+        };
+    };
+...

Documentation/devicetree/bindings/media/i2c/toshiba,tc358746.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/toshiba,tc358746.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Toshiba TC358746 Parallel to MIPI CSI2 Bridge
+
+maintainers:
+  - Marco Felsch <kernel@pengutronix.de>
+
+description: |-
+  The Toshiba TC358746 converts a parallel video stream into a MIPI CSI-2
+  stream. The direction can be either parallel-in -> csi-out or csi-in ->
+  parallel-out The chip is programmable trough I2C and SPI but the SPI
+  interface is only supported in parallel-in -> csi-out mode.
+
+  Note that the current device tree bindings only support the
+  parallel-in -> csi-out path.
+
+properties:
+  compatible:
+    const: toshiba,tc358746
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    description:
+      The phandle to the reference clock source. This corresponds to the
+      hardware pin REFCLK.
+    maxItems: 1
+
+  clock-names:
+    const: refclk
+
+  "#clock-cells":
+    description: |
+      The bridge can act as clock provider for the sensor. To enable this
+      support #clock-cells must be specified. Attention if this feature is used
+      then the mclk rate must be at least: (2 * link-frequency) / 8
+                                           `------------------´   ^
+                                           internal PLL rate   smallest possible
+                                                                   mclk-div
+    const: 0
+
+  clock-output-names:
+    description:
+      The clock name of the MCLK output, the default name is tc358746-mclk.
+    maxItems: 1
+
+  vddc-supply:
+    description: Digital core voltage supply, 1.2 volts
+
+  vddio-supply:
+    description: Digital I/O voltage supply, 1.8 volts
+
+  vddmipi-supply:
+    description: MIPI CSI phy voltage supply, 1.2 volts
+
+  reset-gpios:
+    description:
+      The phandle and specifier for the GPIO that controls the chip reset.
+      This corresponds to the hardware pin RESX which is physically active low.
+    maxItems: 1
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        description: Input port
+
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              hsync-active: true
+              vsync-active: true
+              bus-type:
+                enum: [ 5, 6 ]
+
+            required:
+              - hsync-active
+              - vsync-active
+              - bus-type
+
+      port@1:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        description: Output port
+
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              data-lanes:
+                minItems: 1
+                maxItems: 4
+
+              clock-noncontinuous: true
+              link-frequencies: true
+
+            required:
+              - data-lanes
+              - link-frequencies
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - vddc-supply
+  - vddio-supply
+  - vddmipi-supply
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      csi-bridge@e {
+        compatible = "toshiba,tc358746";
+        reg = <0xe>;
+
+        clocks = <&refclk>;
+        clock-names = "refclk";
+
+        reset-gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+
+        vddc-supply = <&v1_2d>;
+        vddio-supply = <&v1_8d>;
+        vddmipi-supply = <&v1_2d>;
+
+        /* sensor mclk provider */
+        #clock-cells = <0>;
+
+        ports {
+          #address-cells = <1>;
+          #size-cells = <0>;
+
+          /* Input */
+          port@0 {
+            reg = <0>;
+            tc358746_in: endpoint {
+              remote-endpoint = <&sensor_out>;
+              hsync-active = <0>;
+              vsync-active = <0>;
+              bus-type = <5>;
+            };
+          };
+
+          /* Output */
+          port@1 {
+            reg = <1>;
+            tc358746_out: endpoint {
+              remote-endpoint = <&mipi_csi2_in>;
+              data-lanes = <1 2>;
+              clock-noncontinuous;
+              link-frequencies = /bits/ 64 <216000000>;
+            };
+          };
+        };
+      };
+    };

Documentation/userspace-api/media/drivers/st-vgxy61.rst

+.. SPDX-License-Identifier: GPL-2.0
+
+ST VGXY61 camera sensor driver
+==============================
+
+The ST VGXY61 driver implements the following controls:
+
+``V4L2_CID_HDR_SENSOR_MODE``
+-------------------------------
+    Change the sensor HDR mode. A HDR picture is obtained by merging two captures of the same scene
+    using two different exposure periods.
+
+.. flat-table::
+    :header-rows:  0
+    :stub-columns: 0
+    :widths:       1 4
+
+    * - HDR linearize
+      - The merger outputs a long exposure capture as long as it is not saturated.
+    * - HDR substraction
+      - This involves subtracting the short exposure frame from the long exposure frame.
+    * - "No HDR"
+      - This mode is used for standard dynamic range (SDR) exposures.

Documentation/userspace-api/media/v4l/ext-ctrls-camera.rst

@@ -661,3 +661,11 @@ enum v4l2_scene_mode -
 .. [#f1]
    This control may be changed to a menu control in the future, if more
    options are required.
+
+``V4L2_CID_HDR_SENSOR_MODE (menu)``
+    Change the sensor HDR mode. A HDR picture is obtained by merging two
+    captures of the same scene using two different exposure periods. HDR mode
+    describes the way these two captures are merged in the sensor.
+
+    As modes differ for each sensor, menu items are not standardized by this
+    control and are left to the programmer.

Documentation/userspace-api/media/v4l/subdev-formats.rst

@@ -6057,6 +6057,43 @@ the following codes.
       - y\ :sub:`2`
       - y\ :sub:`1`
       - y\ :sub:`0`
+    * .. _MEDIA-BUS-FMT-Y16-1X16:
+
+      - MEDIA_BUS_FMT_Y16_1X16
+      - 0x202e
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      -
+      - y\ :sub:`15`
+      - y\ :sub:`14`
+      - y\ :sub:`13`
+      - y\ :sub:`12`
+      - y\ :sub:`11`
+      - y\ :sub:`10`
+      - y\ :sub:`9`
+      - y\ :sub:`8`
+      - y\ :sub:`7`
+      - y\ :sub:`6`
+      - y\ :sub:`5`
+      - y\ :sub:`4`
+      - y\ :sub:`3`
+      - y\ :sub:`2`
+      - y\ :sub:`1`
+      - y\ :sub:`0`
     * .. _MEDIA-BUS-FMT-UYVY8-1X16:
 
       - MEDIA_BUS_FMT_UYVY8_1X16

MAINTAINERS

@@ -15181,6 +15181,13 @@ S:	Maintained
 T:	git git://linuxtv.org/media_tree.git
 F:	drivers/media/i2c/ov08d10.c
 
+OMNIVISION OV08X40 SENSOR DRIVER
+M:	Jason Chen <jason.z.chen@intel.com>
+L:	linux-media@vger.kernel.org
+S:	Maintained
+T:	git git://linuxtv.org/media_tree.git
+F:	drivers/media/i2c/ov08x40.c
+
 OMNIVISION OV13858 SENSOR DRIVER
 M:	Sakari Ailus <sakari.ailus@linux.intel.com>
 L:	linux-media@vger.kernel.org
@@ -15219,6 +15226,14 @@ S:	Maintained
 T:	git git://linuxtv.org/media_tree.git
 F:	drivers/media/i2c/ov2740.c
 
+OMNIVISION OV4689 SENSOR DRIVER
+M:	Mikhail Rudenko <mike.rudenko@gmail.com>
+L:	linux-media@vger.kernel.org
+S:	Maintained
+T:	git git://linuxtv.org/media_tree.git
+F:	Documentation/devicetree/bindings/media/i2c/ovti,ov4689.yaml
+F:	drivers/media/i2c/ov5647.c
+
 OMNIVISION OV5640 SENSOR DRIVER
 M:	Steve Longerbeam <slongerbeam@gmail.com>
 L:	linux-media@vger.kernel.org
@@ -19188,7 +19203,7 @@ M:	Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
 L:	linux-media@vger.kernel.org
 S:	Maintained
 T:	git git://linuxtv.org/media_tree.git
-F:	Documentation/devicetree/bindings/media/i2c/imx290.txt
+F:	Documentation/devicetree/bindings/media/i2c/sony,imx290.yaml
 F:	drivers/media/i2c/imx290.c
 
 SONY IMX319 SENSOR DRIVER
@@ -19503,6 +19518,16 @@ S:	Maintained
 F:	Documentation/hwmon/stpddc60.rst
 F:	drivers/hwmon/pmbus/stpddc60.c
 
+ST VGXY61 DRIVER
+M:	Benjamin Mugnier <benjamin.mugnier@foss.st.com>
+M:	Sylvain Petinot <sylvain.petinot@foss.st.com>
+L:	linux-media@vger.kernel.org
+S:	Maintained
+T:	git git://linuxtv.org/media_tree.git
+F:	Documentation/devicetree/bindings/media/i2c/st,st-vgxy61.yaml
+F:	Documentation/userspace-api/media/drivers/st-vgxy61.rst
+F:	drivers/media/i2c/st-vgxy61.c
+
 ST VL53L0X ToF RANGER(I2C) IIO DRIVER
 M:	Song Qiang <songqiang1304521@gmail.com>
 L:	linux-iio@vger.kernel.org

drivers/media/i2c/Kconfig

@@ -364,6 +364,19 @@ config VIDEO_OV08D10
           To compile this driver as a module, choose M here: the
           module will be called ov08d10.
 
+config VIDEO_OV08X40
+	tristate "OmniVision OV08X40 sensor support"
+	depends on VIDEO_V4L2 && I2C
+	select MEDIA_CONTROLLER
+	select VIDEO_V4L2_SUBDEV_API
+	select V4L2_FWNODE
+	help
+	  This is a Video4Linux2 sensor driver for the OmniVision
+	  OV08X40 camera.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called ov08x40.
+
 config VIDEO_OV13858
 	tristate "OmniVision OV13858 sensor support"
 	depends on I2C && VIDEO_DEV
@@ -445,6 +458,19 @@ config VIDEO_OV2740
 	  To compile this driver as a module, choose M here: the
 	  module will be called ov2740.
 
+config VIDEO_OV4689
+	tristate "OmniVision OV4689 sensor support"
+	depends on GPIOLIB && VIDEO_DEV && I2C
+	select MEDIA_CONTROLLER
+	select VIDEO_V4L2_SUBDEV_API
+	select V4L2_FWNODE
+	help
+	  This is a Video4Linux2 sensor-level driver for the OmniVision
+	  OV4689 camera.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called ov4689.
+
 config VIDEO_OV5640
 	tristate "OmniVision OV5640 sensor support"
 	depends on OF
@@ -769,6 +795,16 @@ config VIDEO_SR030PC30
 	help
 	  This driver supports SR030PC30 VGA camera from Siliconfile
 
+config VIDEO_ST_VGXY61
+	tristate "ST VGXY61 sensor support"
+	depends on OF && GPIOLIB && VIDEO_DEV && I2C
+	select MEDIA_CONTROLLER
+	select VIDEO_V4L2_SUBDEV_API
+	select V4L2_FWNODE
+	help
+	  This is a Video4Linux2 sensor driver for the ST VGXY61
+	  camera sensor.
+
 config VIDEO_VS6624
 	tristate "ST VS6624 sensor support"
 	depends on VIDEO_DEV && I2C
@@ -1272,6 +1308,23 @@ config VIDEO_TC358743_CEC
 	  When selected the tc358743 will support the optional
 	  HDMI CEC feature.
 
+config VIDEO_TC358746
+	tristate "Toshiba TC358746 parallel-CSI2 bridge"
+	depends on VIDEO_DEV && PM && I2C
+	select VIDEO_V4L2_SUBDEV_API
+	select MEDIA_CONTROLLER
+	select V4L2_FWNODE
+	select GENERIC_PHY_MIPI_DPHY
+	select REGMAP_I2C
+	select COMMON_CLK
+	help
+	  Support for the Toshiba TC358746 parallel to MIPI CSI-2 bridge.
+	  The bridge can work in both directions but currently only the
+	  parallel-in / csi-out path is supported.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called tc358746.
+
 config VIDEO_TVP514X
 	tristate "Texas Instruments TVP514x video decoder"
 	depends on VIDEO_DEV && I2C

drivers/media/i2c/Makefile

@@ -72,6 +72,7 @@ obj-$(CONFIG_VIDEO_NOON010PC30) += noon010pc30.o
 obj-$(CONFIG_VIDEO_OG01A1B) += og01a1b.o
 obj-$(CONFIG_VIDEO_OV02A10) += ov02a10.o
 obj-$(CONFIG_VIDEO_OV08D10) += ov08d10.o
+obj-$(CONFIG_VIDEO_OV08X40) += ov08x40.o
 obj-$(CONFIG_VIDEO_OV13858) += ov13858.o
 obj-$(CONFIG_VIDEO_OV13B10) += ov13b10.o
 obj-$(CONFIG_VIDEO_OV2640) += ov2640.o
@@ -79,6 +80,7 @@ obj-$(CONFIG_VIDEO_OV2659) += ov2659.o
 obj-$(CONFIG_VIDEO_OV2680) += ov2680.o
 obj-$(CONFIG_VIDEO_OV2685) += ov2685.o
 obj-$(CONFIG_VIDEO_OV2740) += ov2740.o
+obj-$(CONFIG_VIDEO_OV4689) += ov4689.o
 obj-$(CONFIG_VIDEO_OV5640) += ov5640.o
 obj-$(CONFIG_VIDEO_OV5645) += ov5645.o
 obj-$(CONFIG_VIDEO_OV5647) += ov5647.o
@@ -117,7 +119,9 @@ obj-$(CONFIG_VIDEO_SAA7185) += saa7185.o
 obj-$(CONFIG_VIDEO_SONY_BTF_MPX) += sony-btf-mpx.o
 obj-$(CONFIG_VIDEO_SR030PC30) += sr030pc30.o
 obj-$(CONFIG_VIDEO_ST_MIPID02) += st-mipid02.o
+obj-$(CONFIG_VIDEO_ST_VGXY61) += st-vgxy61.o
 obj-$(CONFIG_VIDEO_TC358743) += tc358743.o
+obj-$(CONFIG_VIDEO_TC358746) += tc358746.o
 obj-$(CONFIG_VIDEO_TDA1997X) += tda1997x.o
 obj-$(CONFIG_VIDEO_TDA7432) += tda7432.o
 obj-$(CONFIG_VIDEO_TDA9840) += tda9840.o

drivers/media/i2c/ad5820.c

@@ -327,18 +327,18 @@ static int ad5820_probe(struct i2c_client *client,
 
 	ret = media_entity_pads_init(&coil->subdev.entity, 0, NULL);
 	if (ret < 0)
-		goto cleanup2;
+		goto clean_mutex;
 
 	ret = v4l2_async_register_subdev(&coil->subdev);
 	if (ret < 0)
-		goto cleanup;
+		goto clean_entity;
 
 	return ret;
 
-cleanup2:
-	mutex_destroy(&coil->power_lock);
-cleanup:
+clean_entity:
 	media_entity_cleanup(&coil->subdev.entity);
+clean_mutex:
+	mutex_destroy(&coil->power_lock);
 	return ret;
 }
 

drivers/media/i2c/dw9768.c

@@ -414,6 +414,7 @@ static int dw9768_probe(struct i2c_client *client)
 {
 	struct device *dev = &client->dev;
 	struct dw9768 *dw9768;
+	bool full_power;
 	unsigned int i;
 	int ret;
 
@@ -469,13 +470,23 @@ static int dw9768_probe(struct i2c_client *client)
 
 	dw9768->sd.entity.function = MEDIA_ENT_F_LENS;
 
+	/*
+	 * Figure out whether we're going to power up the device here. Generally
+	 * this is done if CONFIG_PM is disabled in a DT system or the device is
+	 * to be powered on in an ACPI system. Similarly for power off in
+	 * remove.
+	 */
 	pm_runtime_enable(dev);
-	if (!pm_runtime_enabled(dev)) {
+	full_power = (is_acpi_node(dev_fwnode(dev)) &&
+		      acpi_dev_state_d0(dev)) ||
+		     (is_of_node(dev_fwnode(dev)) && !pm_runtime_enabled(dev));
+	if (full_power) {
 		ret = dw9768_runtime_resume(dev);
 		if (ret < 0) {
 			dev_err(dev, "failed to power on: %d\n", ret);
 			goto err_clean_entity;
 		}
+		pm_runtime_set_active(dev);
 	}
 
 	ret = v4l2_async_register_subdev(&dw9768->sd);
@@ -484,14 +495,17 @@ static int dw9768_probe(struct i2c_client *client)
 		goto err_power_off;
 	}
 
+	pm_runtime_idle(dev);
+
 	return 0;
 
 err_power_off:
-	if (pm_runtime_enabled(dev))
-		pm_runtime_disable(dev);
-	else
+	if (full_power) {
 		dw9768_runtime_suspend(dev);
+		pm_runtime_set_suspended(dev);
+	}
 err_clean_entity:
+	pm_runtime_disable(dev);
 	media_entity_cleanup(&dw9768->sd.entity);
 err_free_handler:
 	v4l2_ctrl_handler_free(&dw9768->ctrls);
@@ -503,14 +517,17 @@ static void dw9768_remove(struct i2c_client *client)
 {
 	struct v4l2_subdev *sd = i2c_get_clientdata(client);
 	struct dw9768 *dw9768 = sd_to_dw9768(sd);
+	struct device *dev = &client->dev;
 
 	v4l2_async_unregister_subdev(&dw9768->sd);
 	v4l2_ctrl_handler_free(&dw9768->ctrls);
 	media_entity_cleanup(&dw9768->sd.entity);
-	pm_runtime_disable(&client->dev);
-	if (!pm_runtime_status_suspended(&client->dev))
-		dw9768_runtime_suspend(&client->dev);
-	pm_runtime_set_suspended(&client->dev);
+	if ((is_acpi_node(dev_fwnode(dev)) && acpi_dev_state_d0(dev)) ||
+	    (is_of_node(dev_fwnode(dev)) && !pm_runtime_enabled(dev))) {
+		dw9768_runtime_suspend(dev);
+		pm_runtime_set_suspended(dev);
+	}
+	pm_runtime_disable(dev);
 }
 
 static const struct of_device_id dw9768_of_table[] = {

drivers/media/i2c/hi846.c

@@ -2008,22 +2008,24 @@ static int hi846_parse_dt(struct hi846 *hi846, struct device *dev)
 	    bus_cfg.bus.mipi_csi2.num_data_lanes != 4) {
 		dev_err(dev, "number of CSI2 data lanes %d is not supported",
 			bus_cfg.bus.mipi_csi2.num_data_lanes);
-		v4l2_fwnode_endpoint_free(&bus_cfg);
-		return -EINVAL;
+		ret = -EINVAL;
+		goto check_hwcfg_error;
 	}
 
 	hi846->nr_lanes = bus_cfg.bus.mipi_csi2.num_data_lanes;
 
 	if (!bus_cfg.nr_of_link_frequencies) {
 		dev_err(dev, "link-frequency property not found in DT\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto check_hwcfg_error;
 	}
 
 	/* Check that link frequences for all the modes are in device tree */
 	fq = hi846_check_link_freqs(hi846, &bus_cfg);
 	if (fq) {
 		dev_err(dev, "Link frequency of %lld is not supported\n", fq);
-		return -EINVAL;
+		ret = -EINVAL;
+		goto check_hwcfg_error;
 	}
 
 	v4l2_fwnode_endpoint_free(&bus_cfg);
@@ -2044,6 +2046,10 @@ static int hi846_parse_dt(struct hi846 *hi846, struct device *dev)
 	}
 
 	return 0;
+
+check_hwcfg_error:
+	v4l2_fwnode_endpoint_free(&bus_cfg);
+	return ret;
 }
 
 static int hi846_probe(struct i2c_client *client)

drivers/media/i2c/ov2640.c

@@ -16,9 +16,7 @@
 #include <linux/clk.h>
 #include <linux/slab.h>
 #include <linux/delay.h>
-#include <linux/gpio.h>
 #include <linux/gpio/consumer.h>
-#include <linux/of_gpio.h>
 #include <linux/v4l2-mediabus.h>
 #include <linux/videodev2.h>
 

drivers/media/i2c/ov5645.c

@@ -1090,7 +1090,7 @@ static int ov5645_probe(struct i2c_client *client)
 	}
 
 	/* get system clock (xclk) */
-	ov5645->xclk = devm_clk_get(dev, "xclk");
+	ov5645->xclk = devm_clk_get(dev, NULL);
 	if (IS_ERR(ov5645->xclk)) {
 		dev_err(dev, "could not get xclk");
 		return PTR_ERR(ov5645->xclk);

drivers/media/i2c/ov5648.c

@@ -2597,6 +2597,7 @@ static void ov5648_remove(struct i2c_client *client)
 	v4l2_ctrl_handler_free(&sensor->ctrls.handler);
 	mutex_destroy(&sensor->mutex);
 	media_entity_cleanup(&subdev->entity);
+	v4l2_fwnode_endpoint_free(&sensor->endpoint);
 }
 
 static const struct dev_pm_ops ov5648_pm_ops = {

drivers/media/i2c/ov7670.c

@@ -15,7 +15,6 @@
 #include <linux/i2c.h>
 #include <linux/delay.h>
 #include <linux/videodev2.h>
-#include <linux/gpio.h>
 #include <linux/gpio/consumer.h>
 #include <media/v4l2-device.h>
 #include <media/v4l2-event.h>

drivers/media/i2c/ov8856.c

@@ -2110,17 +2110,18 @@ static int ov8856_set_stream(struct v4l2_subdev *sd, int enable)
 	return ret;
 }
 
-static int __ov8856_power_on(struct ov8856 *ov8856)
+static int ov8856_power_on(struct device *dev)
 {
-	struct i2c_client *client = v4l2_get_subdevdata(&ov8856->sd);
+	struct v4l2_subdev *sd = dev_get_drvdata(dev);
+	struct ov8856 *ov8856 = to_ov8856(sd);
 	int ret;
 
-	if (is_acpi_node(dev_fwnode(&client->dev)))
+	if (is_acpi_node(dev_fwnode(dev)))
 		return 0;
 
 	ret = clk_prepare_enable(ov8856->xvclk);
 	if (ret < 0) {
-		dev_err(&client->dev, "failed to enable xvclk\n");
+		dev_err(dev, "failed to enable xvclk\n");
 		return ret;
 	}
 
@@ -2132,7 +2133,7 @@ static int __ov8856_power_on(struct ov8856 *ov8856)
 	ret = regulator_bulk_enable(ARRAY_SIZE(ov8856_supply_names),
 				    ov8856->supplies);
 	if (ret < 0) {
-		dev_err(&client->dev, "failed to enable regulators\n");
+		dev_err(dev, "failed to enable regulators\n");
 		goto disable_clk;
 	}
 
@@ -2148,17 +2149,20 @@ static int __ov8856_power_on(struct ov8856 *ov8856)
 	return ret;
 }
 
-static void __ov8856_power_off(struct ov8856 *ov8856)
+static int ov8856_power_off(struct device *dev)
 {
-	struct i2c_client *client = v4l2_get_subdevdata(&ov8856->sd);
+	struct v4l2_subdev *sd = dev_get_drvdata(dev);
+	struct ov8856 *ov8856 = to_ov8856(sd);
 
-	if (is_acpi_node(dev_fwnode(&client->dev)))
-		return;
+	if (is_acpi_node(dev_fwnode(dev)))
+		return 0;
 
 	gpiod_set_value_cansleep(ov8856->reset_gpio, 1);
 	regulator_bulk_disable(ARRAY_SIZE(ov8856_supply_names),
 			       ov8856->supplies);
 	clk_disable_unprepare(ov8856->xvclk);
+
+	return 0;
 }
 
 static int __maybe_unused ov8856_suspend(struct device *dev)
@@ -2170,7 +2174,7 @@ static int __maybe_unused ov8856_suspend(struct device *dev)
 	if (ov8856->streaming)
 		ov8856_stop_streaming(ov8856);
 
-	__ov8856_power_off(ov8856);
+	ov8856_power_off(dev);
 	mutex_unlock(&ov8856->mutex);
 
 	return 0;
@@ -2184,7 +2188,7 @@ static int __maybe_unused ov8856_resume(struct device *dev)
 
 	mutex_lock(&ov8856->mutex);
 
-	__ov8856_power_on(ov8856);
+	ov8856_power_on(dev);
 	if (ov8856->streaming) {
 		ret = ov8856_start_streaming(ov8856);
 		if (ret) {
@@ -2451,7 +2455,7 @@ static void ov8856_remove(struct i2c_client *client)
 	pm_runtime_disable(&client->dev);
 	mutex_destroy(&ov8856->mutex);
 
-	__ov8856_power_off(ov8856);
+	ov8856_power_off(&client->dev);
 }
 
 static int ov8856_probe(struct i2c_client *client)
@@ -2475,7 +2479,7 @@ static int ov8856_probe(struct i2c_client *client)
 
 	full_power = acpi_dev_state_d0(&client->dev);
 	if (full_power) {
-		ret = __ov8856_power_on(ov8856);
+		ret = ov8856_power_on(&client->dev);
 		if (ret) {
 			dev_err(&client->dev, "failed to power on\n");
 			return ret;
@@ -2531,13 +2535,14 @@ static int ov8856_probe(struct i2c_client *client)
 	mutex_destroy(&ov8856->mutex);
 
 probe_power_off:
-	__ov8856_power_off(ov8856);
+	ov8856_power_off(&client->dev);
 
 	return ret;
 }
 
 static const struct dev_pm_ops ov8856_pm_ops = {
 	SET_SYSTEM_SLEEP_PM_OPS(ov8856_suspend, ov8856_resume)
+	SET_RUNTIME_PM_OPS(ov8856_power_off, ov8856_power_on, NULL)
 };
 
 #ifdef CONFIG_ACPI

drivers/media/i2c/ov9650.c

@@ -10,7 +10,6 @@
  */
 #include <linux/clk.h>
 #include <linux/delay.h>
-#include <linux/gpio.h>
 #include <linux/gpio/consumer.h>
 #include <linux/i2c.h>
 #include <linux/kernel.h>
@@ -30,7 +29,6 @@
 #include <media/v4l2-image-sizes.h>
 #include <media/v4l2-subdev.h>
 #include <media/v4l2-mediabus.h>
-#include <media/i2c/ov9650.h>
 
 static int debug;
 module_param(debug, int, 0644);
@@ -1402,38 +1400,6 @@ static const struct v4l2_subdev_ops ov965x_subdev_ops = {
 	.video = &ov965x_video_ops,
 };
 
-/*
- * Reset and power down GPIOs configuration
- */
-static int ov965x_configure_gpios_pdata(struct ov965x *ov965x,
-				const struct ov9650_platform_data *pdata)
-{
-	int ret, i;
-	int gpios[NUM_GPIOS];
-	struct device *dev = regmap_get_device(ov965x->regmap);
-
-	gpios[GPIO_PWDN] = pdata->gpio_pwdn;
-	gpios[GPIO_RST]  = pdata->gpio_reset;
-
-	for (i = 0; i < ARRAY_SIZE(ov965x->gpios); i++) {
-		int gpio = gpios[i];
-
-		if (!gpio_is_valid(gpio))
-			continue;
-		ret = devm_gpio_request_one(dev, gpio,
-					    GPIOF_OUT_INIT_HIGH, "OV965X");
-		if (ret < 0)
-			return ret;
-		v4l2_dbg(1, debug, &ov965x->sd, "set gpio %d to 1\n", gpio);
-
-		gpio_set_value_cansleep(gpio, 1);
-		gpio_export(gpio, 0);
-		ov965x->gpios[i] = gpio_to_desc(gpio);
-	}
-
-	return 0;
-}
-
 static int ov965x_configure_gpios(struct ov965x *ov965x)
 {
 	struct device *dev = regmap_get_device(ov965x->regmap);
@@ -1493,7 +1459,6 @@ static int ov965x_detect_sensor(struct v4l2_subdev *sd)
 
 static int ov965x_probe(struct i2c_client *client)
 {
-	const struct ov9650_platform_data *pdata = client->dev.platform_data;
 	struct v4l2_subdev *sd;
 	struct ov965x *ov965x;
 	int ret;
@@ -1513,17 +1478,7 @@ static int ov965x_probe(struct i2c_client *client)
 		return PTR_ERR(ov965x->regmap);
 	}
 
-	if (pdata) {
-		if (pdata->mclk_frequency == 0) {
-			dev_err(&client->dev, "MCLK frequency not specified\n");
-			return -EINVAL;
-		}
-		ov965x->mclk_frequency = pdata->mclk_frequency;
-
-		ret = ov965x_configure_gpios_pdata(ov965x, pdata);
-		if (ret < 0)
-			return ret;
-	} else if (dev_fwnode(&client->dev)) {
+	if (dev_fwnode(&client->dev)) {
 		ov965x->clk = devm_clk_get(&client->dev, NULL);
 		if (IS_ERR(ov965x->clk))
 			return PTR_ERR(ov965x->clk);
@@ -1534,7 +1489,7 @@ static int ov965x_probe(struct i2c_client *client)
 			return ret;
 	} else {
 		dev_err(&client->dev,
-			"Neither platform data nor device property specified\n");
+			"No device properties specified\n");
 
 		return -EINVAL;
 	}

drivers/media/platform/samsung/exynos4-is/media-dev.c

@@ -1380,9 +1380,7 @@ static int subdev_notifier_bound(struct v4l2_async_notifier *notifier,
 
 	/* Find platform data for this sensor subdev */
 	for (i = 0; i < ARRAY_SIZE(fmd->sensor); i++)
-		if (fmd->sensor[i].asd &&
-		    fmd->sensor[i].asd->match.fwnode ==
-		    of_fwnode_handle(subdev->dev->of_node))
+		if (fmd->sensor[i].asd == asd)
 			si = &fmd->sensor[i];
 
 	if (si == NULL)

drivers/media/v4l2-core/v4l2-ctrls-defs.c

@@ -1043,6 +1043,7 @@ const char *v4l2_ctrl_get_name(u32 id)
 	case V4L2_CID_UNIT_CELL_SIZE:		return "Unit Cell Size";
 	case V4L2_CID_CAMERA_ORIENTATION:	return "Camera Orientation";
 	case V4L2_CID_CAMERA_SENSOR_ROTATION:	return "Camera Sensor Rotation";
+	case V4L2_CID_HDR_SENSOR_MODE:		return "HDR Sensor Mode";
 
 	/* FM Radio Modulator controls */
 	/* Keep the order of the 'case's the same as in v4l2-controls.h! */
@@ -1370,6 +1371,7 @@ void v4l2_ctrl_fill(u32 id, const char **name, enum v4l2_ctrl_type *type,
 	case V4L2_CID_STATELESS_H264_START_CODE:
 	case V4L2_CID_CAMERA_ORIENTATION:
 	case V4L2_CID_MPEG_VIDEO_INTRA_REFRESH_PERIOD_TYPE:
+	case V4L2_CID_HDR_SENSOR_MODE:
 		*type = V4L2_CTRL_TYPE_MENU;
 		break;
 	case V4L2_CID_LINK_FREQ:

drivers/media/v4l2-core/v4l2-subdev.c

@@ -318,6 +318,20 @@ static int call_get_mbus_config(struct v4l2_subdev *sd, unsigned int pad,
 	       sd->ops->pad->get_mbus_config(sd, pad, config);
 }
 
+static int call_s_stream(struct v4l2_subdev *sd, int enable)
+{
+	int ret;
+
+	ret = sd->ops->video->s_stream(sd, enable);
+
+	if (!enable && ret < 0) {
+		dev_warn(sd->dev, "disabling streaming failed (%d)\n", ret);
+		return 0;
+	}
+
+	return ret;
+}
+
 #ifdef CONFIG_MEDIA_CONTROLLER
 /*
  * Create state-management wrapper for pad ops dealing with subdev state. The
@@ -377,6 +391,7 @@ static const struct v4l2_subdev_pad_ops v4l2_subdev_call_pad_wrappers = {
 static const struct v4l2_subdev_video_ops v4l2_subdev_call_video_wrappers = {
 	.g_frame_interval	= call_g_frame_interval,
 	.s_frame_interval	= call_s_frame_interval,
+	.s_stream		= call_s_stream,
 };
 
 const struct v4l2_subdev_ops v4l2_subdev_call_wrappers = {

include/linux/phy/phy-mipi-dphy.h

@@ -279,6 +279,9 @@ int phy_mipi_dphy_get_default_config(unsigned long pixel_clock,
 				     unsigned int bpp,
 				     unsigned int lanes,
 				     struct phy_configure_opts_mipi_dphy *cfg);
+int phy_mipi_dphy_get_default_config_for_hsclk(unsigned long long hs_clk_rate,
+					       unsigned int lanes,
+					       struct phy_configure_opts_mipi_dphy *cfg);
 int phy_mipi_dphy_config_validate(struct phy_configure_opts_mipi_dphy *cfg);
 
 #endif /* __PHY_MIPI_DPHY_H_ */

include/media/i2c/ov9650.h

-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * OV9650/OV9652 camera sensors driver
- *
- * Copyright (C) 2013 Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
- */
-#ifndef OV9650_H_
-#define OV9650_H_
-
-/**
- * struct ov9650_platform_data - ov9650 driver platform data
- * @mclk_frequency: the sensor's master clock frequency in Hz
- * @gpio_pwdn:	    number of a GPIO connected to OV965X PWDN pin
- * @gpio_reset:     number of a GPIO connected to OV965X RESET pin
- *
- * If any of @gpio_pwdn or @gpio_reset are unused then they should be
- * set to a negative value. @mclk_frequency must always be specified.
- */
-struct ov9650_platform_data {
-	unsigned long mclk_frequency;
-	int gpio_pwdn;
-	int gpio_reset;
-};
-#endif /* OV9650_H_ */