Commit 1fad59ea authored by Stefano Brivio's avatar Stefano Brivio Committed by David S. Miller

selftests: pmtu: Add pmtu_vti6_link_change_mtu test

This test checks that MTU configured from userspace is used on
link creation and changes, and that when it's not passed from
userspace, it's calculated properly from the MTU of the lower
layer.
Signed-off-by: default avatarStefano Brivio <sbrivio@redhat.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 8b6022fc
...@@ -36,14 +36,21 @@ ...@@ -36,14 +36,21 @@
# #
# - pmtu_vti6_link_add_mtu # - pmtu_vti6_link_add_mtu
# Same as above, for IPv6 # Same as above, for IPv6
#
# - pmtu_vti6_link_change_mtu
# Set up two dummy interfaces with different MTUs, create a vti6 tunnel
# and check that configured MTU is used on link creation and changes, and
# that MTU is properly calculated instead when MTU is not configured from
# userspace
tests=" tests="
pmtu_vti6_exception vti6: PMTU exceptions pmtu_vti6_exception vti6: PMTU exceptions
pmtu_vti4_exception vti4: PMTU exceptions pmtu_vti4_exception vti4: PMTU exceptions
pmtu_vti4_default_mtu vti4: default MTU assignment pmtu_vti4_default_mtu vti4: default MTU assignment
pmtu_vti6_default_mtu vti6: default MTU assignment pmtu_vti6_default_mtu vti6: default MTU assignment
pmtu_vti4_link_add_mtu vti4: MTU setting on link creation pmtu_vti4_link_add_mtu vti4: MTU setting on link creation
pmtu_vti6_link_add_mtu vti6: MTU setting on link creation" pmtu_vti6_link_add_mtu vti6: MTU setting on link creation
pmtu_vti6_link_change_mtu vti6: MTU changes on link changes"
NS_A="ns-$(mktemp -u XXXXXX)" NS_A="ns-$(mktemp -u XXXXXX)"
NS_B="ns-$(mktemp -u XXXXXX)" NS_B="ns-$(mktemp -u XXXXXX)"
...@@ -64,6 +71,10 @@ vti6_a_addr="fd00:2::a" ...@@ -64,6 +71,10 @@ vti6_a_addr="fd00:2::a"
vti6_b_addr="fd00:2::b" vti6_b_addr="fd00:2::b"
vti6_mask="64" vti6_mask="64"
dummy6_0_addr="fc00:1000::0"
dummy6_1_addr="fc00:1001::0"
dummy6_mask="64"
cleanup_done=1 cleanup_done=1
err_buf= err_buf=
...@@ -386,6 +397,50 @@ test_pmtu_vti6_link_add_mtu() { ...@@ -386,6 +397,50 @@ test_pmtu_vti6_link_add_mtu() {
return ${fail} return ${fail}
} }
test_pmtu_vti6_link_change_mtu() {
setup namespaces || return 2
${ns_a} ip link add dummy0 mtu 1500 type dummy
[ $? -ne 0 ] && err " dummy not supported" && return 2
${ns_a} ip link add dummy1 mtu 3000 type dummy
${ns_a} ip link set dummy0 up
${ns_a} ip link set dummy1 up
${ns_a} ip addr add ${dummy6_0_addr}/${dummy6_mask} dev dummy0
${ns_a} ip addr add ${dummy6_1_addr}/${dummy6_mask} dev dummy1
fail=0
# Create vti6 interface bound to device, passing MTU, check it
${ns_a} ip link add vti6_a mtu 1300 type vti6 remote ${dummy6_0_addr} local ${dummy6_0_addr}
mtu="$(link_get_mtu "${ns_a}" vti6_a)"
if [ ${mtu} -ne 1300 ]; then
err " vti6 MTU ${mtu} doesn't match configured value 1300"
fail=1
fi
# Move to another device with different MTU, without passing MTU, check
# MTU is adjusted
echo "${ns_a} ip link set vti6_a type vti6 remote ${dummy6_1_addr} local ${dummy6_1_addr}" > /dev/kmsg
${ns_a} ip link set vti6_a type vti6 remote ${dummy6_1_addr} local ${dummy6_1_addr}
mtu="$(link_get_mtu "${ns_a}" vti6_a)"
if [ ${mtu} -ne $((3000 - 40)) ]; then
err " vti MTU ${mtu} is not dummy MTU 3000 minus IPv6 header length"
fail=1
fi
# Move it back, passing MTU, check MTU is not overridden
echo "${ns_a} ip link set vti6_a mtu 1280 type vti6 remote ${dummy6_0_addr} local ${dummy6_0_addr}" > /dev/kmsg
${ns_a} ip link set vti6_a mtu 1280 type vti6 remote ${dummy6_0_addr} local ${dummy6_0_addr}
mtu="$(link_get_mtu "${ns_a}" vti6_a)"
if [ ${mtu} -ne 1280 ]; then
err " vti6 MTU ${mtu} doesn't match configured value 1280"
fail=1
fi
return ${fail}
}
trap cleanup EXIT trap cleanup EXIT
exitcode=0 exitcode=0
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment