Merge tag 'arm-soc/for-4.6/devicetree' of http://github.com/Broadcom/stblinux into next/dt

Merge "Broadcom devicetree changes for 4.6" from Florian Fainelli:

This pull request contains Broadcom ARM-based SoCs Device Tree changes:

- Rafal adds a Device Tree for the D-Link DIR-885L router which is based on the
  BCM47094 SoC similar to the BCM4709

- Simran adds proper audio clock Device Tree nodes to the Cygnus platforms

- Martin adds the auxiliary SPI controllers, makes the UART naming convention
  more standard, and finally adds the auxiliary UART found in the BCM2835 to the
  BCM2835 Device Tree

- Remi adds PWM clock support to the BCM2835 Device Tree

- Lubomir adds a Device Tree for the Raspberry Pi Model A

- Alexander adds Device Tree information for the Raspberry Pi USB power domain

- Dhananjay enables the GPIO-A controller for the Northstar Plus SoCs

- Jon fixes the PCIE Device Tree nodes by pulling them out of the bus-level node,
  removes duplicate CPU definitions, adds PMU nodes, SP804 timers, and SP805 watchdog
  to the Northstar Plus SoCs

* tag 'arm-soc/for-4.6/devicetree' of http://github.com/Broadcom/stblinux:
  ARM: bcm2835: add bcm2835-aux-uart support to DT
  ARM: dts: NSP: Add SP805 Support to DT
  ARM: dts: NSP: Add SP804 Support to DT
  ARM: dts: NSP: Add PMU Support to DT
  ARM: dts: NSP: Fix CPU DT issue
  ARM: dts: NSP: Fix PCIE DT issue
  ARM: dts: enable GPIO-a for Broadcom NSP
  ARM: bcm2835: Add the Raspberry Pi power domain driver to the DT.
  ARM: bcm2835: dt: Add Raspberry Pi Model A
  ARM: bcm2835: follow dt uart node-naming convention
  ARM: bcm2835: Add PWM clock support to the device tree
  ARM: bcm2835: add the auxiliary spi1 and spi2 to the device tree
  ARM: dts: Add audio clock to the existing Broadcom Cygnus clock DT
  ARM: BCM5301X: Add DT for D-Link DIR-885L

arch/arm/boot/dts/Makefile

@@ -62,6 +62,7 @@ dtb-$(CONFIG_ARCH_AXXIA) += \
 	axm5516-amarillo.dtb
 dtb-$(CONFIG_ARCH_BCM2835) += \
 	bcm2835-rpi-b.dtb \
+	bcm2835-rpi-a.dtb \
 	bcm2835-rpi-b-rev2.dtb \
 	bcm2835-rpi-b-plus.dtb \
 	bcm2835-rpi-a-plus.dtb \
@@ -81,6 +82,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
 	bcm4709-buffalo-wxr-1900dhp.dtb \
 	bcm4709-netgear-r7000.dtb \
 	bcm4709-netgear-r8000.dtb \
+	bcm47094-dlink-dir-885l.dtb \
 	bcm94708.dtb \
 	bcm94709.dtb \
 	bcm953012k.dtb

arch/arm/boot/dts/bcm-cygnus-clock.dtsi

@@ -121,4 +121,13 @@ asiu_clks: asiu_clks {
 		clocks = <&osc>;
 		clock-output-names = "keypad", "adc/touch", "pwm";
 	};
+
+	audiopll: audiopll {
+		#clock-cells = <1>;
+		compatible = "brcm,cygnus-audiopll";
+		reg = <0x180aeb00 0x68>;
+		clocks = <&osc>;
+		clock-output-names = "audiopll", "ch0_audio",
+					"ch1_audio", "ch2_audio";
+	};
 };

arch/arm/boot/dts/bcm-nsp.dtsi

@@ -45,14 +45,14 @@ cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu@0 {
+		cpu0: cpu@0 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
 			next-level-cache = <&L2>;
 			reg = <0x0>;
 		};
 
-		cpu@1 {
+		cpu1: cpu@1 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
 			next-level-cache = <&L2>;
@@ -62,24 +62,19 @@ cpu@1 {
 		};
 	};
 
+	pmu {
+		compatible = "arm,cortex-a9-pmu";
+		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH
+			      GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>;
+	};
+
 	mpcore {
 		compatible = "simple-bus";
 		ranges = <0x00000000 0x19000000 0x00023000>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 
-		cpus {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			cpu@0 {
-				device_type = "cpu";
-				compatible = "arm,cortex-a9";
-				next-level-cache = <&L2>;
-				reg = <0x0>;
-			};
-		};
-
 		a9pll: arm_clk@00000 {
 			#clock-cells = <0>;
 			compatible = "brcm,nsp-armpll";
@@ -169,6 +164,18 @@ axi {
 		#address-cells = <1>;
 		#size-cells = <1>;
 
+		gpioa: gpio@0020 {
+			compatible = "brcm,nsp-gpio-a";
+			reg = <0x0020 0x70>,
+			      <0x3f1c4 0x1c>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			ngpios = <32>;
+			interrupt-controller;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-ranges = <&pinctrl 0 0 32>;
+		};
+
 		uart0: serial@0300 {
 			compatible = "ns16550a";
 			reg = <0x0300 0x100>;
@@ -185,78 +192,6 @@ uart1: serial@0400 {
 			status = "disabled";
 		};
 
-		pcie0: pcie@12000 {
-			compatible = "brcm,iproc-pcie";
-			reg = <0x12000 0x1000>;
-
-			#interrupt-cells = <1>;
-			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0 0 0 0 &gic GIC_SPI 131 IRQ_TYPE_NONE>;
-
-			linux,pci-domain = <0>;
-
-			bus-range = <0x00 0xff>;
-
-			#address-cells = <3>;
-			#size-cells = <2>;
-			device_type = "pci";
-
-			/* Note: The HW does not support I/O resources.  So,
-			 * only the memory resource range is being specified.
-			 */
-			ranges = <0x82000000 0 0x08000000 0x08000000 0 0x8000000>;
-
-			status = "disabled";
-		};
-
-		pcie1: pcie@13000 {
-			compatible = "brcm,iproc-pcie";
-			reg = <0x13000 0x1000>;
-
-			#interrupt-cells = <1>;
-			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0 0 0 0 &gic GIC_SPI 137 IRQ_TYPE_NONE>;
-
-			linux,pci-domain = <1>;
-
-			bus-range = <0x00 0xff>;
-
-			#address-cells = <3>;
-			#size-cells = <2>;
-			device_type = "pci";
-
-			/* Note: The HW does not support I/O resources.  So,
-			 * only the memory resource range is being specified.
-			 */
-			ranges = <0x82000000 0 0x40000000 0x40000000 0 0x8000000>;
-
-			status = "disabled";
-		};
-
-		pcie2: pcie@14000 {
-			compatible = "brcm,iproc-pcie";
-			reg = <0x14000 0x1000>;
-
-			#interrupt-cells = <1>;
-			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0 0 0 0 &gic GIC_SPI 143 IRQ_TYPE_NONE>;
-
-			linux,pci-domain = <2>;
-
-			bus-range = <0x00 0xff>;
-
-			#address-cells = <3>;
-			#size-cells = <2>;
-			device_type = "pci";
-
-			/* Note: The HW does not support I/O resources.  So,
-			 * only the memory resource range is being specified.
-			 */
-			ranges = <0x82000000 0 0x48000000 0x48000000 0 0x8000000>;
-
-			status = "disabled";
-		};
-
 		nand: nand@26000 {
 			compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1";
 			reg = <0x026000 0x600>,
@@ -271,6 +206,24 @@ nand: nand@26000 {
 			brcm,nand-has-wp;
 		};
 
+		ccbtimer0: timer@34000 {
+			compatible = "arm,sp804";
+			reg = <0x34000 0x1000>;
+			interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&iprocslow>;
+			clock-names = "apb_pclk";
+		};
+
+		ccbtimer1: timer@35000 {
+			compatible = "arm,sp804";
+			reg = <0x35000 0x1000>;
+			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&iprocslow>;
+			clock-names = "apb_pclk";
+		};
+
 		i2c0: i2c@38000 {
 			compatible = "brcm,iproc-i2c";
 			reg = <0x38000 0x50>;
@@ -280,6 +233,14 @@ i2c0: i2c@38000 {
 			clock-frequency = <100000>;
 		};
 
+		watchdog@39000 {
+			compatible = "arm,sp805", "arm,primecell";
+			reg = <0x39000 0x1000>;
+			interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&iprocslow>, <&iprocslow>;
+			clock-names = "wdogclk", "apb_pclk";
+		};
+
 		lcpll0: lcpll0@3f100 {
 			#clock-cells = <1>;
 			compatible = "brcm,nsp-lcpll0";
@@ -306,4 +267,76 @@ pinctrl: pinctrl@3f1c0 {
 			      <0x3f408 0x04>;
 		};
 	};
+
+	pcie0: pcie@18012000 {
+		compatible = "brcm,iproc-pcie";
+		reg = <0x18012000 0x1000>;
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 131 IRQ_TYPE_NONE>;
+
+		linux,pci-domain = <0>;
+
+		bus-range = <0x00 0xff>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+
+		/* Note: The HW does not support I/O resources.  So,
+		 * only the memory resource range is being specified.
+		 */
+		ranges = <0x82000000 0 0x08000000 0x08000000 0 0x8000000>;
+
+		status = "disabled";
+	};
+
+	pcie1: pcie@18013000 {
+		compatible = "brcm,iproc-pcie";
+		reg = <0x18013000 0x1000>;
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 137 IRQ_TYPE_NONE>;
+
+		linux,pci-domain = <1>;
+
+		bus-range = <0x00 0xff>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+
+		/* Note: The HW does not support I/O resources.  So,
+		 * only the memory resource range is being specified.
+		 */
+		ranges = <0x82000000 0 0x40000000 0x40000000 0 0x8000000>;
+
+		status = "disabled";
+	};
+
+	pcie2: pcie@18014000 {
+		compatible = "brcm,iproc-pcie";
+		reg = <0x18014000 0x1000>;
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 143 IRQ_TYPE_NONE>;
+
+		linux,pci-domain = <2>;
+
+		bus-range = <0x00 0xff>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+
+		/* Note: The HW does not support I/O resources.  So,
+		 * only the memory resource range is being specified.
+		 */
+		ranges = <0x82000000 0 0x48000000 0x48000000 0 0x8000000>;
+
+		status = "disabled";
+	};
 };

arch/arm/boot/dts/bcm2835-rpi-a.dts

+/dts-v1/;
+#include "bcm2835.dtsi"
+#include "bcm2835-rpi.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-a", "brcm,bcm2835";
+	model = "Raspberry Pi Model A";
+
+	leds {
+		act {
+			gpios = <&gpio 16 1>;
+		};
+	};
+};
+
+&gpio {
+	pinctrl-0 = <&gpioout &alt0 &i2s_alt2 &alt3>;
+
+	/* I2S interface */
+	i2s_alt2: i2s_alt2 {
+		brcm,pins = <28 29 30 31>;
+		brcm,function = <BCM2835_FSEL_ALT2>;
+	};
+};

arch/arm/boot/dts/bcm2835-rpi.dtsi

+#include <dt-bindings/power/raspberrypi-power.h>
+
 / {
 	memory {
 		reg = <0 0x10000000>;
@@ -18,6 +20,12 @@ firmware: firmware {
 			compatible = "raspberrypi,bcm2835-firmware";
 			mboxes = <&mailbox>;
 		};
+
+		power: power {
+			compatible = "raspberrypi,bcm2835-power";
+			firmware = <&firmware>;
+			#power-domain-cells = <1>;
+		};
 	};
 };
 
@@ -58,3 +66,11 @@ &sdhci {
 	status = "okay";
 	bus-width = <4>;
 };
+
+&pwm {
+	status = "okay";
+};
+
+&usb {
+	power-domains = <&power RPI_POWER_DOMAIN_USB>;
+};

arch/arm/boot/dts/bcm283x.dtsi

 #include <dt-bindings/pinctrl/bcm2835.h>
 #include <dt-bindings/clock/bcm2835.h>
+#include <dt-bindings/clock/bcm2835-aux.h>
 #include "skeleton.dtsi"
 
 /* This include file covers the common peripherals and configuration between
@@ -111,7 +112,7 @@ gpio: gpio@7e200000 {
 			#interrupt-cells = <2>;
 		};
 
-		uart0: uart@7e201000 {
+		uart0: serial@7e201000 {
 			compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell";
 			reg = <0x7e201000 0x1000>;
 			interrupts = <2 25>;
@@ -159,6 +160,44 @@ aux: aux@0x7e215000 {
 			clocks = <&clocks BCM2835_CLOCK_VPU>;
 		};
 
+		uart1: serial@7e215040 {
+			compatible = "brcm,bcm2835-aux-uart";
+			reg = <0x7e215040 0x40>;
+			interrupts = <1 29>;
+			clocks = <&aux BCM2835_AUX_CLOCK_UART>;
+			status = "disabled";
+		};
+
+		spi1: spi@7e215080 {
+			compatible = "brcm,bcm2835-aux-spi";
+			reg = <0x7e215080 0x40>;
+			interrupts = <1 29>;
+			clocks = <&aux BCM2835_AUX_CLOCK_SPI1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		spi2: spi@7e2150c0 {
+			compatible = "brcm,bcm2835-aux-spi";
+			reg = <0x7e2150c0 0x40>;
+			interrupts = <1 29>;
+			clocks = <&aux BCM2835_AUX_CLOCK_SPI2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		pwm: pwm@7e20c000 {
+			compatible = "brcm,bcm2835-pwm";
+			reg = <0x7e20c000 0x28>;
+			clocks = <&clocks BCM2835_CLOCK_PWM>;
+			assigned-clocks = <&clocks BCM2835_CLOCK_PWM>;
+			assigned-clock-rates = <10000000>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
 		sdhci: sdhci@7e300000 {
 			compatible = "brcm,bcm2835-sdhci";
 			reg = <0x7e300000 0x100>;
@@ -187,7 +226,7 @@ i2c2: i2c@7e805000 {
 			status = "disabled";
 		};
 
-		usb@7e980000 {
+		usb: usb@7e980000 {
 			compatible = "brcm,bcm2835-usb";
 			reg = <0x7e980000 0x10000>;
 			interrupts = <1 9>;

arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts

+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for D-Link DIR-885L
+ *
+ * Copyright (C) 2016 Rafał Miłecki <zajec5@gmail.com>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "dlink,dir-885l", "brcm,bcm47094", "brcm,bcm4708";
+	model = "D-Link DIR-885L";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory {
+		reg = <0x00000000 0x08000000>;
+	};
+
+	nand: nand@18028000 {
+		nandcs@0 {
+			partition@0 {
+				label = "firmware";
+				reg = <0x00000000 0x08000000>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		power-white {
+			label = "bcm53xx:white:power";
+			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		wan-white {
+			label = "bcm53xx:white:wan";
+			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-off";
+		};
+
+		power-amber {
+			label = "bcm53xx:amber:power";
+			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-off";
+		};
+
+		wan-amber {
+			label = "bcm53xx:amber:wan";
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-off";
+		};
+
+		usb3-white {
+			label = "bcm53xx:white:usb3";
+			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-off";
+		};
+
+		2ghz {
+			label = "bcm53xx:white:2ghz";
+			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-off";
+		};
+
+		5ghz {
+			label = "bcm53xx:white:5ghz";
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-off";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
+		};
+
+		/* Switch: router / extender */
+		extender {
+			label = "Extender";
+			linux,code = <BTN_0>;
+			gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
+		};
+
+		restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+	clock-frequency = <125000000>;
+};