Staging: bcm: fix CodingStyle warnings/errors reported by checkpatch.pl in led_control.h

This is a patch to the led_control.h file that fixes numerous warnings
and errors reported by the checkpatch.pl tool. There still remain a few
more, but as this is my first attempt at a commit, I'm not going to be
too adventurous!
Signed-off-by: Gerard Ryan <gerard@ryan.lt>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/staging/bcm/led_control.h

@@ -4,11 +4,11 @@
 /*************************TYPE DEF**********************/
 #define NUM_OF_LEDS 4
 
-#define DSD_START_OFFSET                     0x0200
-#define EEPROM_VERSION_OFFSET           	 0x020E
-#define EEPROM_HW_PARAM_POINTER_ADDRESS 	 0x0218
-#define EEPROM_HW_PARAM_POINTER_ADDRRES_MAP5 0x0220
-#define GPIO_SECTION_START_OFFSET        	 0x03
+#define DSD_START_OFFSET			0x0200
+#define EEPROM_VERSION_OFFSET			0x020E
+#define EEPROM_HW_PARAM_POINTER_ADDRESS		0x0218
+#define EEPROM_HW_PARAM_POINTER_ADDRRES_MAP5	0x0220
+#define GPIO_SECTION_START_OFFSET		0x03
 
 #define COMPATIBILITY_SECTION_LENGTH         42
 #define COMPATIBILITY_SECTION_LENGTH_MAP5    84
@@ -18,27 +18,27 @@
 #define EEPROM_MAP5_MINORVERSION             0
 
 
-#define MAX_NUM_OF_BLINKS 					10
-#define NUM_OF_GPIO_PINS 					16
+#define MAX_NUM_OF_BLINKS			10
+#define NUM_OF_GPIO_PINS			16
 
-#define DISABLE_GPIO_NUM 					0xFF
-#define EVENT_SIGNALED 						1
+#define DISABLE_GPIO_NUM			0xFF
+#define EVENT_SIGNALED				1
 
-#define MAX_FILE_NAME_BUFFER_SIZE 			100
+#define MAX_FILE_NAME_BUFFER_SIZE		100
 
-#define TURN_ON_LED(GPIO, index) do{ \
+#define TURN_ON_LED(GPIO, index) do { \
 							UINT gpio_val = GPIO; \
 							(Adapter->LEDInfo.LEDState[index].BitPolarity == 1) ? \
-							wrmaltWithLock(Adapter,BCM_GPIO_OUTPUT_SET_REG, &gpio_val ,sizeof(gpio_val)) : \
-							wrmaltWithLock(Adapter,BCM_GPIO_OUTPUT_CLR_REG, &gpio_val, sizeof(gpio_val)); \
-						}while(0);
+							wrmaltWithLock(Adapter, BCM_GPIO_OUTPUT_SET_REG, &gpio_val, sizeof(gpio_val)) : \
+							wrmaltWithLock(Adapter, BCM_GPIO_OUTPUT_CLR_REG, &gpio_val, sizeof(gpio_val)); \
+						} while (0);
 
 #define TURN_OFF_LED(GPIO, index)  do { \
 							UINT gpio_val = GPIO; \
 							(Adapter->LEDInfo.LEDState[index].BitPolarity == 1) ? \
-							wrmaltWithLock(Adapter,BCM_GPIO_OUTPUT_CLR_REG,&gpio_val ,sizeof(gpio_val)) : \
-							wrmaltWithLock(Adapter,BCM_GPIO_OUTPUT_SET_REG,&gpio_val ,sizeof(gpio_val));  \
-						}while(0);
+							wrmaltWithLock(Adapter, BCM_GPIO_OUTPUT_CLR_REG, &gpio_val, sizeof(gpio_val)) : \
+							wrmaltWithLock(Adapter, BCM_GPIO_OUTPUT_SET_REG, &gpio_val, sizeof(gpio_val));  \
+						} while (0);
 
 #define B_ULONG32 unsigned long
 
@@ -50,7 +50,7 @@ typedef enum _LEDColors{
 	BLUE_LED = 2,
 	YELLOW_LED = 3,
 	GREEN_LED = 4
-} LEDColors; 				/*Enumerated values of different LED types*/
+} LEDColors;	/*Enumerated values of different LED types*/
 
 typedef enum LedEvents {
 	SHUTDOWN_EXIT = 0x00,
@@ -62,43 +62,41 @@ typedef enum LedEvents {
 	LOWPOWER_MODE_ENTER = 0x20,
 	IDLEMODE_CONTINUE = 0x40,
 	IDLEMODE_EXIT = 0x80,
-	LED_THREAD_INACTIVE = 0x100,  //Makes the LED thread Inactivce. It wil be equivallent to putting the thread on hold.
-	LED_THREAD_ACTIVE = 0x200    //Makes the LED Thread Active back.
-} LedEventInfo_t;			/*Enumerated values of different driver states*/
+	LED_THREAD_INACTIVE = 0x100,  /* Makes the LED thread Inactivce. It wil be equivallent to putting the thread on hold. */
+	LED_THREAD_ACTIVE = 0x200    /* Makes the LED Thread Active back. */
+} LedEventInfo_t;	/* Enumerated values of different driver states */
 
 #define DRIVER_HALT 0xff
 
 
-/*Structure which stores the information of different LED types
- *  and corresponding LED state information of driver states*/
-typedef struct LedStateInfo_t
-{
+/*
+ * Structure which stores the information of different LED types
+ * and corresponding LED state information of driver states
+ */
+typedef struct LedStateInfo_t {
 	UCHAR LED_Type; /* specify GPIO number - use 0xFF if not used */
 	UCHAR LED_On_State; /* Bits set or reset for different states */
 	UCHAR LED_Blink_State; /* Bits set or reset for blinking LEDs for different states */
 	UCHAR GPIO_Num;
-	UCHAR 			BitPolarity;				/*To represent whether H/W is normal polarity or reverse
-											  polarity*/
-}LEDStateInfo, *pLEDStateInfo;
+	UCHAR BitPolarity; /* To represent whether H/W is normal polarity or reverse polarity */
+} LEDStateInfo, *pLEDStateInfo;
 
 
-typedef struct _LED_INFO_STRUCT
-{
+typedef struct _LED_INFO_STRUCT {
 	LEDStateInfo	LEDState[NUM_OF_LEDS];
-	BOOLEAN 		bIdleMode_tx_from_host; /*Variable to notify whether driver came out
-											from idlemode due to Host or target*/
+	BOOLEAN		bIdleMode_tx_from_host; /* Variable to notify whether driver came out from idlemode due to Host or target*/
 	BOOLEAN			bIdle_led_off;
 	wait_queue_head_t   notify_led_event;
 	wait_queue_head_t	idleModeSyncEvent;
- 	struct task_struct  *led_cntrl_threadid;
-    int                 led_thread_running;
+	struct task_struct  *led_cntrl_threadid;
+	int                 led_thread_running;
 	BOOLEAN			bLedInitDone;
 
 } LED_INFO_STRUCT, *PLED_INFO_STRUCT;
-//LED Thread state.
-#define BCM_LED_THREAD_DISABLED			 	 0 //LED Thread is not running.
-#define BCM_LED_THREAD_RUNNING_ACTIVELY  	 1 //LED thread is running.
-#define BCM_LED_THREAD_RUNNING_INACTIVELY	 2 //LED thread has been put on hold
+/* LED Thread state. */
+#define BCM_LED_THREAD_DISABLED		0 /* LED Thread is not running. */
+#define BCM_LED_THREAD_RUNNING_ACTIVELY	1 /* LED thread is running. */
+#define BCM_LED_THREAD_RUNNING_INACTIVELY 2 /*LED thread has been put on hold*/