[ARM] mmp: append device support in jasper

Support regulator MAX8649, PMIC MAX8925 into the Jasper.
Backlight & power supply components of MAX8925 are enabled in Jasper.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

arch/arm/mach-mmp/jasper.c

@@ -15,12 +15,16 @@
 #include <linux/platform_device.h>
 #include <linux/io.h>
 #include <linux/gpio.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/max8649.h>
+#include <linux/mfd/max8925.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <mach/addr-map.h>
 #include <mach/mfp-mmp2.h>
 #include <mach/mmp2.h>
+#include <mach/irqs.h>
 
 #include "common.h"
 
@@ -58,6 +62,63 @@ static unsigned long jasper_pin_config[] __initdata = {
 	GPIO149_ND_CLE,
 	GPIO112_ND_RDY0,
 	GPIO160_ND_RDY1,
+
+	/* PMIC */
+	PMIC_PMIC_INT | MFP_LPM_EDGE_FALL,
+};
+
+static struct regulator_consumer_supply max8649_supply[] = {
+	REGULATOR_SUPPLY("vcc_core", NULL),
+};
+
+static struct regulator_init_data max8649_init_data = {
+	.constraints	= {
+		.name		= "vcc_core range",
+		.min_uV		= 1150000,
+		.max_uV		= 1280000,
+		.always_on	= 1,
+		.boot_on	= 1,
+		.valid_ops_mask	= REGULATOR_CHANGE_VOLTAGE,
+	},
+	.num_consumer_supplies	= 1,
+	.consumer_supplies	= &max8649_supply[0],
+};
+
+static struct max8649_platform_data jasper_max8649_info = {
+	.mode		= 2,	/* VID1 = 1, VID0 = 0 */
+	.extclk		= 0,
+	.ramp_timing	= MAX8649_RAMP_32MV,
+	.regulator	= &max8649_init_data,
+};
+
+static struct max8925_backlight_pdata jasper_backlight_data = {
+	.dual_string	= 0,
+};
+
+static struct max8925_power_pdata jasper_power_data = {
+	.batt_detect		= 0,	/* can't detect battery by ID pin */
+	.topoff_threshold	= MAX8925_TOPOFF_THR_10PER,
+	.fast_charge		= MAX8925_FCHG_1000MA,
+};
+
+static struct max8925_platform_data jasper_max8925_info = {
+	.backlight		= &jasper_backlight_data,
+	.power			= &jasper_power_data,
+	.irq_base		= IRQ_BOARD_START,
+};
+
+static struct i2c_board_info jasper_twsi1_info[] = {
+	[0] = {
+		.type		= "max8649",
+		.addr		= 0x60,
+		.platform_data	= &jasper_max8649_info,
+	},
+	[1] = {
+		.type		= "max8925",
+		.addr		= 0x3c,
+		.irq		= IRQ_MMP2_PMIC,
+		.platform_data	= &jasper_max8925_info,
+	},
 };
 
 static void __init jasper_init(void)
@@ -67,6 +128,9 @@ static void __init jasper_init(void)
 	/* on-chip devices */
 	mmp2_add_uart(1);
 	mmp2_add_uart(3);
+	mmp2_add_twsi(1, NULL, ARRAY_AND_SIZE(jasper_twsi1_info));
+
+	regulator_has_full_constraints();
 }
 
 MACHINE_START(MARVELL_JASPER, "Jasper Development Platform")