Commit 250481d3 authored by Olof Johansson's avatar Olof Johansson

Merge tag 'at91-4.5-dt2' of...

Merge tag 'at91-4.5-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt

Second batch of DT changes for 4.5:
- addition of sound nodes for sama5d2 and the xplained
- addition of a new patform by Landis+Gyr: VInCo

* tag 'at91-4.5-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
  ARM: at91/dt: sama5d2 Xplained: add pdmic node
  ARM: at91/dt: sama5d2: add pdmic node
  ARM: at91/dt: Add Support for the L+G VInCo platform
Signed-off-by: default avatarOlof Johansson <olof@lixom.net>
parents 84829814 ca6349a8
......@@ -50,7 +50,8 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
sama5d36ek.dtb \
at91-sama5d4_ma5d4evk.dtb \
at91-sama5d4_xplained.dtb \
at91-sama5d4ek.dtb
at91-sama5d4ek.dtb \
at91-vinco.dtb
dtb-$(CONFIG_ARCH_ATLAS6) += \
atlas6-evb.dtb
dtb-$(CONFIG_ARCH_ATLAS7) += \
......
......@@ -119,6 +119,16 @@ macb0: ethernet@f8008000 {
status = "okay";
};
pdmic@f8018000 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pdmic_default>;
atmel,model = "PDMIC @ sama5d2_xplained";
atmel,mic-min-freq = <1000000>;
atmel,mic-max-freq = <3246000>;
atmel,mic-offset = <0x0>;
status = "okay";
};
uart1: serial@f8020000 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1_default>;
......@@ -289,6 +299,12 @@ pinctrl_macb0_default: macb0_default {
bias-disable;
};
pinctrl_pdmic_default: pdmic_default {
pinmux = <PIN_PB26__PDMIC_DAT>,
<PIN_PB27__PDMIC_CLK>;
bias-disable;
};
pinctrl_sdmmc0_default: sdmmc0_default {
cmd_data {
pinmux = <PIN_PA1__SDMMC0_CMD>,
......
/*
* Device Tree file for VInCo platform
*
* Copyright (C) 2014 Atmel,
* 2014 Nicolas Ferre <nicolas.ferre@atmel.com>
* 2015 Gregory CLEMENT <gregory.clement@free-electrons.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "sama5d4.dtsi"
/ {
model = "L+G VInCo platform";
compatible = "l+g,vinco", "atmel,sama5d4", "atmel,sama5";
chosen {
stdout-path = "serial0:115200n8";
};
memory {
reg = <0x20000000 0x4000000>;
};
clocks {
slow_xtal {
clock-frequency = <32768>;
};
main_xtal {
clock-frequency = <12000000>;
};
};
ahb {
apb {
adc0: adc@fc034000 {
status = "okay"; /* Enable ADC IIO support */
};
mmc0: mmc@f8000000 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0
&pinctrl_mmc0_dat1_3
&pinctrl_mmc0_dat4_7>;
vqmmc-supply = <&vcc_3v3_reg>;
vmmc-supply = <&vcc_3v3_reg>;
no-1-8-v;
status = "okay";
slot@0 {
reg = <0>;
bus-width = <8>;
non-removable;
broken-cd;
status = "okay";
};
};
spi0: spi@f8010000 {
cs-gpios = <&pioC 3 0>, <0>, <0>, <0>;
status = "okay";
m25p80@0 {
compatible = "n25q32b", "jedec,spi-nor";
spi-max-frequency = <50000000>;
reg = <0>;
};
};
i2c0: i2c@f8014000 {
status = "okay";
};
i2c1: i2c@f8018000 {
status = "okay";
/* kerkey security module */
};
macb0: ethernet@f8020000 {
phy-mode = "rmii";
status = "okay";
ethernet-phy@1 {
reg = <0x1>;
reset-gpios = <&pioE 8 GPIO_ACTIVE_HIGH>;
interrupt-parent = <&pioB>;
interrupts = <15 IRQ_TYPE_EDGE_FALLING>;
};
};
i2c2: i2c@f8024000 {
status = "okay";
rtc1: rtc@64 {
compatible = "epson,rx8900";
reg = <0x32>;
};
};
usart2: serial@fc008000 {
/* MBUS */
status = "okay";
};
usart3: serial@fc00c000 {
/* debug */
status = "okay";
};
usart4: serial@fc010000 {
/* LMN */
pinctrl-0 = <&pinctrl_usart4 &pinctrl_usart4_rts>;
linux,rs485-enabled-at-boot-time;
status = "okay";
};
macb1: ethernet@fc028000 {
phy-mode = "rmii";
status = "okay";
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
ethernet-phy@1 {
reg = <0x1>;
interrupt-parent = <&pioB>;
interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
reset-gpios = <&pioE 6 GPIO_ACTIVE_HIGH>;
};
};
watchdog@fc068640 {
status = "okay";
};
pinctrl@fc06a000 {
board {
pinctrl_usba_vbus: usba_vbus {
atmel,pins =
<AT91_PIOE 31 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
};
};
};
};
usb0: gadget@00400000 {
atmel,vbus-gpio = <&pioE 31 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usba_vbus>;
status = "disable";
};
usb1: ohci@00500000 {
num-ports = <3>;
atmel,vbus-gpio = <0
&pioE 11 GPIO_ACTIVE_LOW
&pioE 12 GPIO_ACTIVE_LOW
>;
status = "disable";
};
usb2: ehci@00600000 {
/* 4G Modem */
status = "okay";
};
};
leds {
compatible = "gpio-leds";
status = "okay";
led_err {
label = "err";
gpios = <&pioA 7 GPIO_ACTIVE_LOW>;
default-state = "off";
};
led_rssi {
label = "rssi";
gpios = <&pioA 9 GPIO_ACTIVE_LOW>;
default-state = "off";
};
led_tls {
label = "tls";
gpios = <&pioA 24 GPIO_ACTIVE_LOW>;
default-state = "off";
};
led_lmc {
label = "lmc";
gpios = <&pioA 25 GPIO_ACTIVE_LOW>;
default-state = "off";
};
led_wmt {
label = "wmt";
gpios = <&pioA 29 GPIO_ACTIVE_LOW>;
default-state = "off";
};
led_pwr {
label = "pwr";
gpios = <&pioA 26 GPIO_ACTIVE_LOW>;
default-state = "on";
};
};
vcc_3v3_reg: fixedregulator@0 {
compatible = "regulator-fixed";
regulator-name = "VCC 3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
regulator-always-on;
};
};
......@@ -637,6 +637,12 @@ trng_clk: trng_clk {
atmel,clk-output-range = <0 83000000>;
};
pdmic_clk: pdmic_clk {
#clock-cells = <0>;
reg = <48>;
atmel,clk-output-range = <0 83000000>;
};
i2s0_clk: i2s0_clk {
#clock-cells = <0>;
reg = <54>;
......@@ -763,6 +769,11 @@ pwm_gclk: pwm_gclk {
atmel,clk-output-range = <0 83000000>;
};
pdmic_gclk: pdmic_gclk {
#clock-cells = <0>;
reg = <48>;
};
i2s0_gclk: i2s0_gclk {
#clock-cells = <0>;
reg = <54>;
......@@ -852,6 +863,19 @@ tcb1: timer@f8010000 {
clock-names = "t0_clk", "slow_clk";
};
pdmic: pdmic@f8018000 {
compatible = "atmel,sama5d2-pdmic";
reg = <0xf8018000 0x124>;
interrupts = <48 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
| AT91_XDMAC_DT_PERID(50))>;
dma-names = "rx";
clocks = <&pdmic_clk>, <&pdmic_gclk>;
clock-names = "pclk", "gclk";
status = "disabled";
};
uart0: serial@f801c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf801c000 0x100>;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment