Commit 25624b98 authored by Rabin Vincent's avatar Rabin Vincent Committed by Jesper Nilsson

CRIS v32: add ARTPEC-3 and P1343 device trees

Add a device tree for the Axis P1343 with the ARTPEC-3 SoC and on-board
LEDs and RTC.
Signed-off-by: default avatarRabin Vincent <rabin@rab.in>
Signed-off-by: default avatarJesper Nilsson <jespern@axis.com>
parent a95b3ba2
/ {
#address-cells = <1>;
#size-cells = <1>;
interrupt-parent = <&intc>;
cpus {
#address-cells = <1>;
#size-cells = <0>;
cpu@0 {
device_type = "cpu";
model = "axis,crisv32";
reg = <0>;
};
};
soc {
compatible = "simple-bus";
model = "artpec3";
#address-cells = <1>;
#size-cells = <1>;
ranges;
intc: interrupt-controller {
compatible = "axis,crisv32-intc";
reg = <0xb002a000 0x1000>;
interrupt-controller;
#interrupt-cells = <1>;
};
gio: gpio@b0020000 {
compatible = "axis,artpec3-gio";
reg = <0xb0020000 0x1000>;
interrupts = <61>;
gpio-controller;
#gpio-cells = <3>;
};
serial@b003e000 {
compatible = "axis,etraxfs-uart";
reg = <0xb003e000 0x1000>;
interrupts = <64>;
status = "disabled";
};
};
};
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/include/ "artpec3.dtsi"
/ {
model = "Axis P1343 Network Camera";
compatible = "axis,p1343";
aliases {
serial0 = &uart0;
};
soc {
uart0: serial@b003e000 {
status = "okay";
};
};
i2c {
compatible = "i2c-gpio";
gpios = <&gio 3 0 0xa>, <&gio 2 0 0xa>;
i2c-gpio,delay-us = <2>;
#address-cells = <1>;
#size-cells = <0>;
rtc@51 {
compatible = "nxp,pcf8563";
reg = <0x51>;
};
};
leds {
compatible = "gpio-leds";
status_green {
label = "status:green";
gpios = <&gio 0 GPIO_ACTIVE_LOW 0xc>;
linux,default-trigger = "heartbeat";
};
status_red {
label = "status:red";
gpios = <&gio 1 GPIO_ACTIVE_LOW 0xc>;
};
network_green {
label = "network:green";
gpios = <&gio 2 GPIO_ACTIVE_LOW 0xc>;
};
network_red {
label = "network:red";
gpios = <&gio 3 GPIO_ACTIVE_LOW 0xc>;
};
power_red {
label = "power:red";
gpios = <&gio 4 GPIO_ACTIVE_LOW 0xc>;
};
};
gpio_keys {
compatible = "gpio-keys";
#address-cells = <1>;
#size-cells = <0>;
activity-button@0 {
label = "Activity Button";
linux,code = <KEY_FN>;
gpios = <&gio 13 GPIO_ACTIVE_LOW 0xd>;
};
};
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment