m68k: Remove the broken Hades support

This patch removes the Hades support that was marked as BROKEN 5 years ago.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

arch/m68k/Kconfig

@@ -122,22 +122,9 @@ config ATARI
 	  this kernel on an Atari, say Y here and browse the material
 	  available in <file:Documentation/m68k>; otherwise say N.
 
-config HADES
-	bool "Hades support"
-	depends on ATARI && BROKEN
-	help
-	  This option enables support for the Hades Atari clone. If you plan
-	  to use this kernel on a Hades, say Y here; otherwise say N.
-
 config PCI
 	bool
-	depends on HADES
-	default y
 	help
-	  Find out whether you have a PCI motherboard. PCI is the name of a
-	  bus system, i.e. the way the CPU talks to the other stuff inside
-	  your box. Other bus systems are ISA, EISA, MicroChannel (MCA) or
-	  VESA. If you have PCI, say Y, otherwise N.
 
 config MAC
 	bool "Macintosh support"

arch/m68k/atari/Makefile

@@ -5,7 +5,4 @@
 obj-y		:= config.o time.o debug.o ataints.o stdma.o \
 			atasound.o stram.o
 
-ifeq ($(CONFIG_PCI),y)
-obj-$(CONFIG_HADES)	+= hades-pci.o
-endif
 obj-$(CONFIG_ATARI_KBD_CORE)	+= atakeyb.o

arch/m68k/atari/ataints.c

@@ -407,10 +407,8 @@ void __init atari_init_IRQ(void)
 		 * gets overruns)
 		 */
 
-		if (!MACH_IS_HADES) {
-			vectors[VEC_INT2] = falcon_hblhandler;
-			vectors[VEC_INT4] = falcon_hblhandler;
-		}
+		vectors[VEC_INT2] = falcon_hblhandler;
+		vectors[VEC_INT4] = falcon_hblhandler;
 	}
 
 	if (ATARIHW_PRESENT(PCM_8BIT) && ATARIHW_PRESENT(MICROWIRE)) {

arch/m68k/atari/config.c

@@ -231,7 +231,7 @@ void __init config_atari(void)
 	 */
 
 	printk("Atari hardware found: ");
-	if (MACH_IS_MEDUSA || MACH_IS_HADES) {
+	if (MACH_IS_MEDUSA) {
 		/* There's no Atari video hardware on the Medusa, but all the
 		 * addresses below generate a DTACK so no bus error occurs! */
 	} else if (hwreg_present(f030_xreg)) {
@@ -269,10 +269,6 @@ void __init config_atari(void)
 		ATARIHW_SET(SCSI_DMA);
 		printk("TT_SCSI_DMA ");
 	}
-	if (!MACH_IS_HADES && hwreg_present(&st_dma.dma_hi)) {
-		ATARIHW_SET(STND_DMA);
-		printk("STND_DMA ");
-	}
 	/*
 	 * The ST-DMA address registers aren't readable
 	 * on all Medusas, so the test below may fail
@@ -294,12 +290,11 @@ void __init config_atari(void)
 		ATARIHW_SET(YM_2149);
 		printk("YM2149 ");
 	}
-	if (!MACH_IS_MEDUSA && !MACH_IS_HADES &&
-		hwreg_present(&tt_dmasnd.ctrl)) {
+	if (!MACH_IS_MEDUSA && hwreg_present(&tt_dmasnd.ctrl)) {
 		ATARIHW_SET(PCM_8BIT);
 		printk("PCM ");
 	}
-	if (!MACH_IS_HADES && hwreg_present(&falcon_codec.unused5)) {
+	if (hwreg_present(&falcon_codec.unused5)) {
 		ATARIHW_SET(CODEC);
 		printk("CODEC ");
 	}
@@ -313,7 +308,7 @@ void __init config_atari(void)
 	    (tt_scc_dma.dma_ctrl = 0x01, (tt_scc_dma.dma_ctrl & 1) == 1) &&
 	    (tt_scc_dma.dma_ctrl = 0x00, (tt_scc_dma.dma_ctrl & 1) == 0)
 #else
-	    !MACH_IS_MEDUSA && !MACH_IS_HADES
+	    !MACH_IS_MEDUSA
 #endif
 	    ) {
 		ATARIHW_SET(SCC_DMA);
@@ -327,10 +322,7 @@ void __init config_atari(void)
 		ATARIHW_SET(ST_ESCC);
 		printk("ST_ESCC ");
 	}
-	if (MACH_IS_HADES) {
-		ATARIHW_SET(VME);
-		printk("VME ");
-	} else if (hwreg_present(&tt_scu.sys_mask)) {
+	if (hwreg_present(&tt_scu.sys_mask)) {
 		ATARIHW_SET(SCU);
 		/* Assume a VME bus if there's a SCU */
 		ATARIHW_SET(VME);
@@ -340,7 +332,7 @@ void __init config_atari(void)
 		ATARIHW_SET(ANALOG_JOY);
 		printk("ANALOG_JOY ");
 	}
-	if (!MACH_IS_HADES && hwreg_present(blitter.halftone)) {
+	if (hwreg_present(blitter.halftone)) {
 		ATARIHW_SET(BLITTER);
 		printk("BLITTER ");
 	}
@@ -349,8 +341,7 @@ void __init config_atari(void)
 		printk("IDE ");
 	}
 #if 1 /* This maybe wrong */
-	if (!MACH_IS_MEDUSA && !MACH_IS_HADES &&
-	    hwreg_present(&tt_microwire.data) &&
+	if (!MACH_IS_MEDUSA && hwreg_present(&tt_microwire.data) &&
 	    hwreg_present(&tt_microwire.mask) &&
 	    (tt_microwire.mask = 0x7ff,
 	     udelay(1),
@@ -369,19 +360,18 @@ void __init config_atari(void)
 		mach_hwclk = atari_tt_hwclk;
 		mach_set_clock_mmss = atari_tt_set_clock_mmss;
 	}
-	if (!MACH_IS_HADES && hwreg_present(&mste_rtc.sec_ones)) {
+	if (hwreg_present(&mste_rtc.sec_ones)) {
 		ATARIHW_SET(MSTE_CLK);
 		printk("MSTE_CLK ");
 		mach_hwclk = atari_mste_hwclk;
 		mach_set_clock_mmss = atari_mste_set_clock_mmss;
 	}
-	if (!MACH_IS_MEDUSA && !MACH_IS_HADES &&
-	    hwreg_present(&dma_wd.fdc_speed) &&
+	if (!MACH_IS_MEDUSA && hwreg_present(&dma_wd.fdc_speed) &&
 	    hwreg_write(&dma_wd.fdc_speed, 0)) {
 		ATARIHW_SET(FDCSPEED);
 		printk("FDC_SPEED ");
 	}
-	if (!MACH_IS_HADES && !ATARIHW_PRESENT(ST_SCSI)) {
+	if (!ATARIHW_PRESENT(ST_SCSI)) {
 		ATARIHW_SET(ACSI);
 		printk("ACSI ");
 	}
@@ -449,7 +439,7 @@ void __init config_atari(void)
 	 * 0xFFxxxxxx -> 0x00xxxxxx, so that the first 16MB is accessible
 	 * in the last 16MB of the address space.
 	 */
-	tos_version = (MACH_IS_MEDUSA || MACH_IS_HADES) ?
+	tos_version = (MACH_IS_MEDUSA) ?
 			0xfff : *(unsigned short *)0xff000002;
 	atari_rtc_year_offset = (tos_version < 0x306) ? 70 : 68;
 }
@@ -511,8 +501,7 @@ static void atari_reset(void)
 	 * On the Medusa, phys. 0x4 may contain garbage because it's no
 	 * ROM.  See above for explanation why we cannot use PTOV(4).
 	 */
-	reset_addr = MACH_IS_HADES ? 0x7fe00030 :
-		     MACH_IS_MEDUSA || MACH_IS_AB40 ? 0xe00030 :
+	reset_addr = MACH_IS_MEDUSA || MACH_IS_AB40 ? 0xe00030 :
 		     *(unsigned long *) 0xff000004;
 
 	/* reset ACIA for switch off OverScan, if it's active */
@@ -606,8 +595,6 @@ static void atari_get_model(char *model)
 		if (MACH_IS_MEDUSA)
 			/* Medusa has TT _MCH cookie */
 			strcat(model, "Medusa");
-		else if (MACH_IS_HADES)
-			strcat(model, "Hades");
 		else
 			strcat(model, "TT");
 		break;

arch/m68k/kernel/bios32.c

@@ -476,10 +476,12 @@ void __init pcibios_init(void)
 	printk("Linux/m68k PCI BIOS32 revision %x.%02x\n", MAJOR_REV, MINOR_REV);
 
 	bus_info = NULL;
-#ifdef CONFIG_HADES
+
+/* Hades code was:
 	if (MACH_IS_HADES)
 		bus_info = init_hades_pci();
-#endif
+*/
+
 	if (bus_info != NULL)
 	{
 		printk("PCI: Probing PCI hardware\n");

arch/m68k/kernel/process.c

@@ -78,7 +78,7 @@ unsigned long thread_saved_pc(struct task_struct *tsk)
 static void default_idle(void)
 {
 	if (!need_resched())
-#if defined(MACH_ATARI_ONLY) && !defined(CONFIG_HADES)
+#if defined(MACH_ATARI_ONLY)
 		/* block out HSYNC on the atari (falcon) */
 		__asm__("stop #0x2200" : : : "cc");
 #else

drivers/block/ataflop.c

@@ -1882,10 +1882,6 @@ static int __init atari_floppy_init (void)
 		/* Amiga, Mac, ... don't have Atari-compatible floppy :-) */
 		return -ENODEV;
 
-	if (MACH_IS_HADES)
-		/* Hades doesn't have Atari-compatible floppy */
-		return -ENODEV;
-
 	if (register_blkdev(FLOPPY_MAJOR,"fd"))
 		return -EBUSY;
 

drivers/scsi/Kconfig

@@ -1670,14 +1670,6 @@ config ATARI_SCSI_RESET_BOOT
 	  boot process fractionally longer but may assist recovery from errors
 	  that leave the devices with SCSI operations partway completed.
 
-config TT_DMA_EMUL
-	bool "Hades SCSI DMA emulator"
-	depends on ATARI_SCSI && HADES
-	help
-	  This option enables code which emulates the TT SCSI DMA chip on the
-	  Hades. This increases the SCSI transfer rates at least ten times
-	  compared to PIO transfers.
-
 config MAC_SCSI
 	bool "Macintosh NCR5380 SCSI"
 	depends on MAC && SCSI=y

drivers/scsi/atari_scsi.c

@@ -249,10 +249,6 @@ static int setup_hostid = -1;
 module_param(setup_hostid, int, 0);
 
 
-#if defined(CONFIG_TT_DMA_EMUL)
-#include "atari_dma_emul.c"
-#endif
-
 #if defined(REAL_DMA)
 
 static int scsi_dma_is_ignored_buserr(unsigned char dma_stat)
@@ -695,21 +691,8 @@ int atari_scsi_detect(struct scsi_host_template *host)
 #ifdef REAL_DMA
 		tt_scsi_dma.dma_ctrl = 0;
 		atari_dma_residual = 0;
-#ifdef CONFIG_TT_DMA_EMUL
-		if (MACH_IS_HADES) {
-			if (request_irq(IRQ_AUTO_2, hades_dma_emulator,
-					 IRQ_TYPE_PRIO, "Hades DMA emulator",
-					 hades_dma_emulator)) {
-				printk(KERN_ERR "atari_scsi_detect: cannot allocate irq %d, aborting (MACH_IS_HADES)",IRQ_AUTO_2);
-				free_irq(IRQ_TT_MFP_SCSI, instance);
-				scsi_unregister(atari_scsi_host);
-				atari_stram_free(atari_dma_buffer);
-				atari_dma_buffer = 0;
-				return 0;
-			}
-		}
-#endif
-		if (MACH_IS_MEDUSA || MACH_IS_HADES) {
+
+		if (MACH_IS_MEDUSA) {
 			/* While the read overruns (described by Drew Eckhardt in
 			 * NCR5380.c) never happened on TTs, they do in fact on the Medusa
 			 * (This was the cause why SCSI didn't work right for so long
@@ -1007,11 +990,7 @@ static unsigned long atari_dma_xfer_len(unsigned long wanted_len,
 					Scsi_Cmnd *cmd, int write_flag)
 {
 	unsigned long	possible_len, limit;
-#ifndef CONFIG_TT_DMA_EMUL
-	if (MACH_IS_HADES)
-		/* Hades has no SCSI DMA at all :-( Always force use of PIO */
-		return 0;
-#endif
+
 	if (IS_A_TT())
 		/* TT SCSI DMA can transfer arbitrary #bytes */
 		return wanted_len;

include/asm-m68k/atarihw.h

@@ -39,7 +39,6 @@ extern int atari_dont_touch_floppy_select;
 #define MACH_IS_TT	((atari_mch_cookie >> 16) == ATARI_MCH_TT)
 #define MACH_IS_FALCON	((atari_mch_cookie >> 16) == ATARI_MCH_FALCON)
 #define MACH_IS_MEDUSA	(atari_mch_type == ATARI_MACH_MEDUSA)
-#define MACH_IS_HADES	(atari_mch_type == ATARI_MACH_HADES)
 #define MACH_IS_AB40	(atari_mch_type == ATARI_MACH_AB40)
 
 /* values for atari_switches */

include/asm-m68k/entry.h

@@ -31,7 +31,7 @@
  */
 
 /* the following macro is used when enabling interrupts */
-#if defined(MACH_ATARI_ONLY) && !defined(CONFIG_HADES)
+#if defined(MACH_ATARI_ONLY)
 	/* block out HSYNC on the atari */
 #define ALLOWINT	(~0x400)
 #define	MAX_NOINT_IPL	3

include/asm-m68k/virtconvert.h

@@ -40,15 +40,9 @@ static inline void *phys_to_virt(unsigned long address)
 
 /*
  * IO bus memory addresses are 1:1 with the physical address,
- * except on the PCI bus of the Hades.
  */
-#ifdef CONFIG_HADES
-#define virt_to_bus(a) (virt_to_phys(a) + (MACH_IS_HADES ? 0x80000000 : 0))
-#define bus_to_virt(a) (phys_to_virt((a) - (MACH_IS_HADES ? 0x80000000 : 0)))
-#else
 #define virt_to_bus virt_to_phys
 #define bus_to_virt phys_to_virt
-#endif
 
 #endif
 #endif