Commit 2a83fba6 authored by Christian Grönke's avatar Christian Grönke Committed by Jeff Kirsher

igb: Remove superfluous reset to PHY and page 0 selection

This patch reverts two previous applied patches to fix an issue
that appeared when using SGMII based SFP modules. In the current
state the driver will try to reset the PHY before obtaining the
phy_addr of the SGMII attached PHY. That leads to an error in
e1000_write_phy_reg_sgmii_82575. Causing the initialization to
fail:

    igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
    igb: Copyright (c) 2007-2014 Intel Corporation.
    igb: probe of ????:??:??.? failed with error -3

The patches being reverted are:

    commit 18278533
    Author: Aaron Sierra <asierra@xes-inc.com>
    Date:   Tue Nov 29 10:03:56 2016 -0600

        igb: reset the PHY before reading the PHY ID

    commit 440aeca4
    Author: Matwey V Kornilov <matwey@sai.msu.ru>
    Date:   Thu Nov 24 13:32:48 2016 +0300

         igb: Explicitly select page 0 at initialization

The first reverted patch directly causes the problem mentioned above.
In case of SGMII the phy_addr is not known at this point and will
only be obtained by 'igb_get_phy_id_82575' further down in the code.
The second removed patch selects forces selection of page 0 in the
PHY. Something that the reset tries to address as well.

As pointed out by Alexander Duzck, the patch below fixes the same
issue but in the proper location:

    commit 4e684f59
    Author: Chris J Arges <christopherarges@gmail.com>
    Date:   Wed Nov 2 09:13:42 2016 -0500

        igb: Workaround for igb i210 firmware issue

Reverts: 440aeca4.
Reverts: 18278533.
Signed-off-by: default avatarChristian Grönke <c.groenke@infodas.de>
Reviewed-by: default avatarAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: default avatarAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
parent 7f6cdbda
...@@ -225,19 +225,7 @@ static s32 igb_init_phy_params_82575(struct e1000_hw *hw) ...@@ -225,19 +225,7 @@ static s32 igb_init_phy_params_82575(struct e1000_hw *hw)
hw->bus.func = (rd32(E1000_STATUS) & E1000_STATUS_FUNC_MASK) >> hw->bus.func = (rd32(E1000_STATUS) & E1000_STATUS_FUNC_MASK) >>
E1000_STATUS_FUNC_SHIFT; E1000_STATUS_FUNC_SHIFT;
/* Make sure the PHY is in a good state. Several people have reported
* firmware leaving the PHY's page select register set to something
* other than the default of zero, which causes the PHY ID read to
* access something other than the intended register.
*/
ret_val = hw->phy.ops.reset(hw);
if (ret_val) {
hw_dbg("Error resetting the PHY.\n");
goto out;
}
/* Set phy->phy_addr and phy->id. */ /* Set phy->phy_addr and phy->id. */
igb_write_phy_reg_82580(hw, I347AT4_PAGE_SELECT, 0);
ret_val = igb_get_phy_id_82575(hw); ret_val = igb_get_phy_id_82575(hw);
if (ret_val) if (ret_val)
return ret_val; return ret_val;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment