wireless: add new wil6210 802.11ad 60GHz driver

This adds support for the 60 GHz 802.11ad Wilocity card
through a new driver, wil6210. Wilocity implemented the
firmware, QCA maintains the device driver.

Currently supported:

- STA: with security
- AP: limited to 1 connected STA, security disabled
- Monitor: due to a hardware/firmware limitation
  either control or non-control frames are monitored

Using a STA and AP with this drive, one can assemble
a fully functional BSS. Throughput of 1.2Gbps is achieved
with iperf.

The wil6210 cards have on-board flash memory for the
firmware, the cards comes pre-flashed and no firmware
download is required.

For more details see:

http://wireless.kernel.org/en/users/Drivers/wil6210Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

MAINTAINERS

@@ -1353,6 +1353,14 @@ W:	http://wireless.kernel.org/en/users/Drivers/ath9k
 S:	Supported
 F:	drivers/net/wireless/ath/ath9k/
 
+WILOCITY WIL6210 WIRELESS DRIVER
+M:	Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
+L:	linux-wireless@vger.kernel.org
+L:	wil6210@qca.qualcomm.com
+S:	Supported
+W:	http://wireless.kernel.org/en/users/Drivers/wil6210
+F:	drivers/net/wireless/ath/wil6210/
+
 CARL9170 LINUX COMMUNITY WIRELESS DRIVER
 M:	Christian Lamparter <chunkeey@googlemail.com>
 L:	linux-wireless@vger.kernel.org

drivers/net/wireless/ath/Kconfig

@@ -30,5 +30,6 @@ source "drivers/net/wireless/ath/ath9k/Kconfig"
 source "drivers/net/wireless/ath/carl9170/Kconfig"
 source "drivers/net/wireless/ath/ath6kl/Kconfig"
 source "drivers/net/wireless/ath/ar5523/Kconfig"
+source "drivers/net/wireless/ath/wil6210/Kconfig"
 
 endif

drivers/net/wireless/ath/Makefile

@@ -3,6 +3,7 @@ obj-$(CONFIG_ATH9K_HW)		+= ath9k/
 obj-$(CONFIG_CARL9170)		+= carl9170/
 obj-$(CONFIG_ATH6KL)		+= ath6kl/
 obj-$(CONFIG_AR5523)		+= ar5523/
+obj-$(CONFIG_WIL6210)		+= wil6210/
 
 obj-$(CONFIG_ATH_COMMON)	+= ath.o
 

drivers/net/wireless/ath/wil6210/Kconfig

+config WIL6210
+	tristate "Wilocity 60g WiFi card wil6210 support"
+	depends on CFG80211
+	depends on PCI
+	default n
+	---help---
+	  This module adds support for wireless adapter based on
+	  wil6210 chip by Wilocity. It supports operation on the
+	  60 GHz band, covered by the IEEE802.11ad standard.
+
+	  http://wireless.kernel.org/en/users/Drivers/wil6210
+
+	  If you choose to build it as a module, it will be called
+	  wil6210
+
+config WIL6210_ISR_COR
+	bool "Use Clear-On-Read mode for ISR registers for wil6210"
+	depends on WIL6210
+	default y
+	---help---
+	  ISR registers on wil6210 chip may operate in either
+	  COR (Clear-On-Read) or W1C (Write-1-to-Clear) mode.
+	  For production code, use COR (say y); is default since
+	  it saves extra target transaction;
+	  For ISR debug, use W1C (say n); is allows to monitor ISR
+	  registers with debugfs. If COR were used, ISR would
+	  self-clear when accessed for debug purposes, it makes
+	  such monitoring impossible.
+	  Say y unless you debug interrupts

drivers/net/wireless/ath/wil6210/Makefile

+obj-$(CONFIG_WIL6210) += wil6210.o
+
+wil6210-objs := main.o
+wil6210-objs += netdev.o
+wil6210-objs += cfg80211.o
+wil6210-objs += pcie_bus.o
+wil6210-objs += debugfs.o
+wil6210-objs += wmi.o
+wil6210-objs += interrupt.o
+wil6210-objs += txrx.o
+
+subdir-ccflags-y += -Werror
+subdir-ccflags-y += -D__CHECK_ENDIAN__

drivers/net/wireless/ath/wil6210/dbg_hexdump.h

+#ifndef WIL_DBG_HEXDUMP_H_
+#define WIL_DBG_HEXDUMP_H_
+
+#if defined(CONFIG_DYNAMIC_DEBUG)
+#define wil_dynamic_hex_dump(prefix_str, prefix_type, rowsize,	\
+			     groupsize, buf, len, ascii)	\
+do {								\
+	DEFINE_DYNAMIC_DEBUG_METADATA(descriptor,		\
+		__builtin_constant_p(prefix_str) ? prefix_str : "hexdump");\
+	if (unlikely(descriptor.flags & _DPRINTK_FLAGS_PRINT))	\
+		print_hex_dump(KERN_DEBUG, prefix_str,		\
+			       prefix_type, rowsize, groupsize,	\
+			       buf, len, ascii);		\
+} while (0)
+
+#define wil_print_hex_dump_debug(prefix_str, prefix_type, rowsize,	\
+				 groupsize, buf, len, ascii)		\
+	wil_dynamic_hex_dump(prefix_str, prefix_type, rowsize,		\
+			     groupsize, buf, len, ascii)
+
+#define print_hex_dump_bytes(prefix_str, prefix_type, buf, len)	\
+	wil_dynamic_hex_dump(prefix_str, prefix_type, 16, 1, buf, len, true)
+#else /* defined(CONFIG_DYNAMIC_DEBUG) */
+#define wil_print_hex_dump_debug(prefix_str, prefix_type, rowsize,	\
+				 groupsize, buf, len, ascii)		\
+	print_hex_dump(KERN_DEBUG, prefix_str, prefix_type, rowsize,	\
+		       groupsize, buf, len, ascii)
+#endif /* defined(CONFIG_DYNAMIC_DEBUG) */
+
+#endif /* WIL_DBG_HEXDUMP_H_ */

drivers/net/wireless/ath/wil6210/netdev.c

+/*
+ * Copyright (c) 2012 Qualcomm Atheros, Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/slab.h>
+
+#include "wil6210.h"
+
+static int wil_open(struct net_device *ndev)
+{
+	struct wil6210_priv *wil = ndev_to_wil(ndev);
+
+	return wil_up(wil);
+}
+
+static int wil_stop(struct net_device *ndev)
+{
+	struct wil6210_priv *wil = ndev_to_wil(ndev);
+
+	return wil_down(wil);
+}
+
+/*
+ * AC to queue mapping
+ *
+ * AC_VO -> queue 3
+ * AC_VI -> queue 2
+ * AC_BE -> queue 1
+ * AC_BK -> queue 0
+ */
+static u16 wil_select_queue(struct net_device *ndev, struct sk_buff *skb)
+{
+	static const u16 wil_1d_to_queue[8] = { 1, 0, 0, 1, 2, 2, 3, 3 };
+	struct wil6210_priv *wil = ndev_to_wil(ndev);
+	u16 rc;
+
+	skb->priority = cfg80211_classify8021d(skb);
+
+	rc = wil_1d_to_queue[skb->priority];
+
+	wil_dbg_TXRX(wil, "%s() %d -> %d\n", __func__, (int)skb->priority,
+		     (int)rc);
+
+	return rc;
+}
+
+static const struct net_device_ops wil_netdev_ops = {
+	.ndo_open		= wil_open,
+	.ndo_stop		= wil_stop,
+	.ndo_start_xmit		= wil_start_xmit,
+	.ndo_select_queue	= wil_select_queue,
+	.ndo_set_mac_address    = eth_mac_addr,
+	.ndo_validate_addr      = eth_validate_addr,
+};
+
+void *wil_if_alloc(struct device *dev, void __iomem *csr)
+{
+	struct net_device *ndev;
+	struct wireless_dev *wdev;
+	struct wil6210_priv *wil;
+	struct ieee80211_channel *ch;
+	int rc = 0;
+
+	wdev = wil_cfg80211_init(dev);
+	if (IS_ERR(wdev)) {
+		dev_err(dev, "wil_cfg80211_init failed\n");
+		return wdev;
+	}
+
+	wil = wdev_to_wil(wdev);
+	wil->csr = csr;
+	wil->wdev = wdev;
+
+	rc = wil_priv_init(wil);
+	if (rc) {
+		dev_err(dev, "wil_priv_init failed\n");
+		goto out_wdev;
+	}
+
+	wdev->iftype = NL80211_IFTYPE_STATION; /* TODO */
+	/* default monitor channel */
+	ch = wdev->wiphy->bands[IEEE80211_BAND_60GHZ]->channels;
+	cfg80211_chandef_create(&wdev->preset_chandef, ch, NL80211_CHAN_NO_HT);
+
+	ndev = alloc_netdev_mqs(0, "wlan%d", ether_setup, WIL6210_TX_QUEUES, 1);
+	if (!ndev) {
+		dev_err(dev, "alloc_netdev_mqs failed\n");
+		rc = -ENOMEM;
+		goto out_priv;
+	}
+
+	ndev->netdev_ops = &wil_netdev_ops;
+	ndev->ieee80211_ptr = wdev;
+	SET_NETDEV_DEV(ndev, wiphy_dev(wdev->wiphy));
+	wdev->netdev = ndev;
+
+	wil_link_off(wil);
+
+	return wil;
+
+ out_priv:
+	wil_priv_deinit(wil);
+
+ out_wdev:
+	wil_wdev_free(wil);
+
+	return ERR_PTR(rc);
+}
+
+void wil_if_free(struct wil6210_priv *wil)
+{
+	struct net_device *ndev = wil_to_ndev(wil);
+	if (!ndev)
+		return;
+
+	free_netdev(ndev);
+	wil_priv_deinit(wil);
+	wil_wdev_free(wil);
+}
+
+int wil_if_add(struct wil6210_priv *wil)
+{
+	struct net_device *ndev = wil_to_ndev(wil);
+	int rc;
+
+	rc = register_netdev(ndev);
+	if (rc < 0) {
+		dev_err(&ndev->dev, "Failed to register netdev: %d\n", rc);
+		return rc;
+	}
+
+	wil_link_off(wil);
+
+	return 0;
+}
+
+void wil_if_remove(struct wil6210_priv *wil)
+{
+	struct net_device *ndev = wil_to_ndev(wil);
+
+	unregister_netdev(ndev);
+}

drivers/net/wireless/ath/wil6210/pcie_bus.c

+/*
+ * Copyright (c) 2012 Qualcomm Atheros, Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/netdevice.h>
+#include <linux/debugfs.h>
+#include <linux/pci.h>
+#include <linux/moduleparam.h>
+
+#include "wil6210.h"
+
+static int use_msi = 1;
+module_param(use_msi, int, S_IRUGO);
+MODULE_PARM_DESC(use_msi,
+		 " Use MSI interrupt: "
+		 "0 - don't, 1 - (default) - single, or 3");
+
+/* Bus ops */
+static int wil_if_pcie_enable(struct wil6210_priv *wil)
+{
+	struct pci_dev *pdev = wil->pdev;
+	int rc;
+
+	pci_set_master(pdev);
+
+	/*
+	 * how many MSI interrupts to request?
+	 */
+	switch (use_msi) {
+	case 3:
+	case 1:
+	case 0:
+		break;
+	default:
+		wil_err(wil, "Invalid use_msi=%d, default to 1\n",
+			use_msi);
+		use_msi = 1;
+	}
+	wil->n_msi = use_msi;
+	if (wil->n_msi) {
+		wil_dbg(wil, "Setup %d MSI interrupts\n", use_msi);
+		rc = pci_enable_msi_block(pdev, wil->n_msi);
+		if (rc && (wil->n_msi == 3)) {
+			wil_err(wil, "3 MSI mode failed, try 1 MSI\n");
+			wil->n_msi = 1;
+			rc = pci_enable_msi_block(pdev, wil->n_msi);
+		}
+		if (rc) {
+			wil_err(wil, "pci_enable_msi failed, use INTx\n");
+			wil->n_msi = 0;
+		}
+	} else {
+		wil_dbg(wil, "MSI interrupts disabled, use INTx\n");
+	}
+
+	rc = wil6210_init_irq(wil, pdev->irq);
+	if (rc)
+		goto stop_master;
+
+	/* need reset here to obtain MAC */
+	rc = wil_reset(wil);
+	if (rc)
+		goto release_irq;
+
+	return 0;
+
+ release_irq:
+	wil6210_fini_irq(wil, pdev->irq);
+	/* safe to call if no MSI */
+	pci_disable_msi(pdev);
+ stop_master:
+	pci_clear_master(pdev);
+	return rc;
+}
+
+static int wil_if_pcie_disable(struct wil6210_priv *wil)
+{
+	struct pci_dev *pdev = wil->pdev;
+
+	pci_clear_master(pdev);
+	/* disable and release IRQ */
+	wil6210_fini_irq(wil, pdev->irq);
+	/* safe to call if no MSI */
+	pci_disable_msi(pdev);
+	/* TODO: disable HW */
+
+	return 0;
+}
+
+static int wil_pcie_probe(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+	struct wil6210_priv *wil;
+	struct device *dev = &pdev->dev;
+	void __iomem *csr;
+	int rc;
+
+	/* check HW */
+	dev_info(&pdev->dev, WIL_NAME " device found [%04x:%04x] (rev %x)\n",
+		 (int)pdev->vendor, (int)pdev->device, (int)pdev->revision);
+
+	if (pci_resource_len(pdev, 0) != WIL6210_MEM_SIZE) {
+		dev_err(&pdev->dev, "Not " WIL_NAME "? "
+			"BAR0 size is %lu while expecting %lu\n",
+			(ulong)pci_resource_len(pdev, 0), WIL6210_MEM_SIZE);
+		return -ENODEV;
+	}
+
+	rc = pci_enable_device(pdev);
+	if (rc) {
+		dev_err(&pdev->dev, "pci_enable_device failed\n");
+		return -ENODEV;
+	}
+	/* rollback to err_disable_pdev */
+
+	rc = pci_request_region(pdev, 0, WIL_NAME);
+	if (rc) {
+		dev_err(&pdev->dev, "pci_request_region failed\n");
+		goto err_disable_pdev;
+	}
+	/* rollback to err_release_reg */
+
+	csr = pci_ioremap_bar(pdev, 0);
+	if (!csr) {
+		dev_err(&pdev->dev, "pci_ioremap_bar failed\n");
+		rc = -ENODEV;
+		goto err_release_reg;
+	}
+	/* rollback to err_iounmap */
+	dev_info(&pdev->dev, "CSR at %pR -> %p\n", &pdev->resource[0], csr);
+
+	wil = wil_if_alloc(dev, csr);
+	if (IS_ERR(wil)) {
+		rc = (int)PTR_ERR(wil);
+		dev_err(dev, "wil_if_alloc failed: %d\n", rc);
+		goto err_iounmap;
+	}
+	/* rollback to if_free */
+
+	pci_set_drvdata(pdev, wil);
+	wil->pdev = pdev;
+
+	/* FW should raise IRQ when ready */
+	rc = wil_if_pcie_enable(wil);
+	if (rc) {
+		wil_err(wil, "Enable device failed\n");
+		goto if_free;
+	}
+	/* rollback to bus_disable */
+
+	rc = wil_if_add(wil);
+	if (rc) {
+		wil_err(wil, "wil_if_add failed: %d\n", rc);
+		goto bus_disable;
+	}
+
+	wil6210_debugfs_init(wil);
+
+	/* check FW is alive */
+	wmi_echo(wil);
+
+	return 0;
+
+ bus_disable:
+	wil_if_pcie_disable(wil);
+ if_free:
+	wil_if_free(wil);
+ err_iounmap:
+	pci_iounmap(pdev, csr);
+ err_release_reg:
+	pci_release_region(pdev, 0);
+ err_disable_pdev:
+	pci_disable_device(pdev);
+
+	return rc;
+}
+
+static void wil_pcie_remove(struct pci_dev *pdev)
+{
+	struct wil6210_priv *wil = pci_get_drvdata(pdev);
+
+	wil6210_debugfs_remove(wil);
+	wil_if_pcie_disable(wil);
+	wil_if_remove(wil);
+	wil_if_free(wil);
+	pci_iounmap(pdev, wil->csr);
+	pci_release_region(pdev, 0);
+	pci_disable_device(pdev);
+	pci_set_drvdata(pdev, NULL);
+}
+
+static DEFINE_PCI_DEVICE_TABLE(wil6210_pcie_ids) = {
+	{ PCI_DEVICE(0x1ae9, 0x0301) },
+	{ /* end: all zeroes */	},
+};
+MODULE_DEVICE_TABLE(pci, wil6210_pcie_ids);
+
+static struct pci_driver wil6210_driver = {
+	.probe		= wil_pcie_probe,
+	.remove		= wil_pcie_remove,
+	.id_table	= wil6210_pcie_ids,
+	.name		= WIL_NAME,
+};
+
+module_pci_driver(wil6210_driver);
+
+MODULE_LICENSE("Dual BSD/GPL");
+MODULE_AUTHOR("Qualcomm Atheros <wil6210@qca.qualcomm.com>");
+MODULE_DESCRIPTION("Driver for 60g WiFi WIL6210 card");