[PATCH] skge: whitespace fixes

Minor whitespace cleanups.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

drivers/net/skge.c

@@ -248,7 +248,7 @@ static int skge_set_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
 	} else {
 		u32 setting;
 
-		switch(ecmd->speed) {
+		switch (ecmd->speed) {
 		case SPEED_1000:
 			if (ecmd->duplex == DUPLEX_FULL)
 				setting = SUPPORTED_1000baseT_Full;
@@ -1026,7 +1026,7 @@ static void bcom_check_link(struct skge_hw *hw, int port)
 			}
 
 			/* Check Duplex mismatch */
-			switch(aux & PHY_B_AS_AN_RES_MSK) {
+			switch (aux & PHY_B_AS_AN_RES_MSK) {
 			case PHY_B_RES_1000FD:
 				skge->duplex = DUPLEX_FULL;
 				break;
@@ -1097,7 +1097,7 @@ static void bcom_phy_init(struct skge_port *skge, int jumbo)
 	r |=  XM_MMU_NO_PRE;
 	xm_write16(hw, port, XM_MMU_CMD,r);
 
-	switch(id1) {
+	switch (id1) {
 	case PHY_BCOM_ID1_C0:
 		/*
 		 * Workaround BCOM Errata for the C0 type.

drivers/net/skge.h

@@ -1509,7 +1509,7 @@ enum {
 	PHY_M_LEDC_TX_C_MSB	= 1<<0, /* Tx Control (MSB, 88E1111 only) */
 };
 
-#define PHY_M_LED_PULS_DUR(x)	(	((x)<<12) & PHY_M_LEDC_PULS_MSK)
+#define PHY_M_LED_PULS_DUR(x)	(((x)<<12) & PHY_M_LEDC_PULS_MSK)
 
 enum {
 	PULS_NO_STR	= 0,/* no pulse stretching */
@@ -1522,7 +1522,7 @@ enum {
 	PULS_1300MS	= 7,/* 1.3 s to 2.7 s */
 };
 
-#define PHY_M_LED_BLINK_RT(x)	(	((x)<<8) & PHY_M_LEDC_BL_R_MSK)
+#define PHY_M_LED_BLINK_RT(x)	(((x)<<8) & PHY_M_LEDC_BL_R_MSK)
 
 enum {
 	BLINK_42MS	= 0,/* 42 ms */
@@ -1602,9 +1602,9 @@ enum {
 	PHY_M_FELP_LED0_MSK = 0xf, /* Bit  3.. 0: LED0 Mask (SPEED) */
 };
 
-#define PHY_M_FELP_LED2_CTRL(x)	(	((x)<<8) & PHY_M_FELP_LED2_MSK)
-#define PHY_M_FELP_LED1_CTRL(x)	(	((x)<<4) & PHY_M_FELP_LED1_MSK)
-#define PHY_M_FELP_LED0_CTRL(x)	(	((x)<<0) & PHY_M_FELP_LED0_MSK)
+#define PHY_M_FELP_LED2_CTRL(x)	(((x)<<8) & PHY_M_FELP_LED2_MSK)
+#define PHY_M_FELP_LED1_CTRL(x)	(((x)<<4) & PHY_M_FELP_LED1_MSK)
+#define PHY_M_FELP_LED0_CTRL(x)	(((x)<<0) & PHY_M_FELP_LED0_MSK)
 
 enum {
 	LED_PAR_CTRL_COLX	= 0x00,
@@ -1640,7 +1640,7 @@ enum {
 	PHY_M_MAC_MD_COPPER	= 5,/* Copper only */
 	PHY_M_MAC_MD_1000BX	= 7,/* 1000Base-X only */
 };
-#define PHY_M_MAC_MODE_SEL(x)	(	((x)<<7) & PHY_M_MAC_MD_MSK)
+#define PHY_M_MAC_MODE_SEL(x)	(((x)<<7) & PHY_M_MAC_MD_MSK)
 
 /*****  PHY_MARV_PHY_CTRL (page 3)		16 bit r/w	LED Control Reg. *****/
 enum {
@@ -1650,10 +1650,10 @@ enum {
 	PHY_M_LEDC_STA0_MSK	= 0xf, /* Bit  3.. 0: STAT0 LED Ctrl. Mask */
 };
 
-#define PHY_M_LEDC_LOS_CTRL(x)	(	((x)<<12) & PHY_M_LEDC_LOS_MSK)
-#define PHY_M_LEDC_INIT_CTRL(x)	(	((x)<<8) & PHY_M_LEDC_INIT_MSK)
-#define PHY_M_LEDC_STA1_CTRL(x)	(	((x)<<4) & PHY_M_LEDC_STA1_MSK)
-#define PHY_M_LEDC_STA0_CTRL(x)	(	((x)<<0) & PHY_M_LEDC_STA0_MSK)
+#define PHY_M_LEDC_LOS_CTRL(x)	(((x)<<12) & PHY_M_LEDC_LOS_MSK)
+#define PHY_M_LEDC_INIT_CTRL(x)	(((x)<<8) & PHY_M_LEDC_INIT_MSK)
+#define PHY_M_LEDC_STA1_CTRL(x)	(((x)<<4) & PHY_M_LEDC_STA1_MSK)
+#define PHY_M_LEDC_STA0_CTRL(x)	(((x)<<0) & PHY_M_LEDC_STA0_MSK)
 
 /* GMAC registers  */
 /* Port Registers */