Merge tag 'nand/for-4.7' of github.com:linux-nand/linux

Updates from Boris Brezillon:

This pull request contains the following infrastructure changes:
* introduction of the ECC algo concept to extend the ECC mode one
* replacement of the nand_ecclayout infrastructure by something more
  future-proof.
* addition of an mtd-activity led trigger to replace the nand-activity
  one

And a bunch of specific NAND driver improvements/fixes. Here are the
changes that are worth mentioning:
* rework of the OMAP GPMC and NAND drivers
* prepare the sunxi NAND driver to receive DMA support
* handle bitflips in erased pages on GPMI revisions that do not support
  this in hardware.

* tag 'nand/for-4.7' of github.com:linux-nand/linux: (152 commits)
  mtd: brcmnand: respect ECC algorithm set by NAND subsystem
  gpmi-nand: Handle ECC Errors in erased pages
  Documentation: devicetree: deprecate "soft_bch" nand-ecc-mode value
  mtd: nand: add support for "nand-ecc-algo" DT property
  mtd: mtd: drop NAND_ECC_SOFT_BCH enum value
  mtd: drop support for NAND_ECC_SOFT_BCH as "soft_bch" mapping
  mtd: nand: read ECC algorithm from the new field
  mtd: nand: fsmc: validate ECC setup by checking algorithm directly
  mtd: nand: set ECC algorithm to Hamming on fallback
  staging: mt29f_spinand: set ECC algorithm explicitly
  CRIS v32: nand: set ECC algorithm explicitly
  mtd: nand: atmel: set ECC algorithm explicitly
  mtd: nand: davinci: set ECC algorithm explicitly
  mtd: nand: bf5xx: set ECC algorithm explicitly
  mtd: nand: omap2: Fix high memory dma prefetch transfer
  mtd: nand: omap2: Start dma request before enabling prefetch
  mtd: nandsim: add __init attribute
  mtd: nand: move of_get_nand_xxx() helpers into nand_base.c
  mtd: nand: sh_flctl: rely on generic DT parsing done in nand_scan_ident()
  mtd: nand: mxc: rely on generic DT parsing done in nand_scan_ident()
  ...

Documentation/devicetree/bindings/bus/ti-gpmc.txt → Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt

@@ -32,6 +32,19 @@ Required properties:
 			bootloader) are used for the physical address decoding.
 			As this will change in the future, filling correct
 			values here is a requirement.
+ - interrupt-controller: The GPMC driver implements and interrupt controller for
+			the NAND events "fifoevent" and "termcount" plus the
+			rising/falling edges on the GPMC_WAIT pins.
+			The interrupt number mapping is as follows
+			0 - NAND_fifoevent
+			1 - NAND_termcount
+			2 - GPMC_WAIT0 pin edge
+			3 - GPMC_WAIT1 pin edge, and so on.
+ - interrupt-cells:	Must be set to 2
+ - gpio-controller:	The GPMC driver implements a GPIO controller for the
+			GPMC WAIT pins that can be used as general purpose inputs.
+			0 maps to GPMC_WAIT0 pin.
+ - gpio-cells:		Must be set to 2
 
 Timing properties for child nodes. All are optional and default to 0.
 
@@ -130,6 +143,10 @@ Example for an AM33xx board:
 		#address-cells = <2>;
 		#size-cells = <1>;
 		ranges = <0 0 0x08000000 0x10000000>; /* CS0 @addr 0x8000000, size 0x10000000 */
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		#gpio-cells = <2>;
 
 		/* child nodes go here */
 	};

Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt

@@ -24,6 +24,7 @@ Required properties:
                          brcm,brcmnand-v5.0
                          brcm,brcmnand-v6.0
                          brcm,brcmnand-v6.1
+                         brcm,brcmnand-v6.2
                          brcm,brcmnand-v7.0
                          brcm,brcmnand-v7.1
                          brcm,brcmnand

Documentation/devicetree/bindings/mtd/gpmc-nand.txt

@@ -13,7 +13,11 @@ Documentation/devicetree/bindings/mtd/nand.txt
 
 Required properties:
 
- - reg:		The CS line the peripheral is connected to
+ - compatible:	"ti,omap2-nand"
+ - reg:		range id (CS number), base offset and length of the
+		NAND I/O space
+ - interrupt-parent: must point to gpmc node
+ - interrupts:	Two interrupt specifiers, one for fifoevent, one for termcount.
 
 Optional properties:
 
@@ -44,6 +48,7 @@ Optional properties:
 		locating ECC errors for BCHx algorithms. SoC devices which have
 		ELM hardware engines should specify this device node in .dtsi
 		Using ELM for ECC error correction frees some CPU cycles.
+ - rb-gpios:	GPIO specifier for the ready/busy# pin.
 
 For inline partition table parsing (optional):
 
@@ -55,20 +60,26 @@ Example for an AM33xx board:
 	gpmc: gpmc@50000000 {
 		compatible = "ti,am3352-gpmc";
 		ti,hwmods = "gpmc";
-		reg = <0x50000000 0x1000000>;
+		reg = <0x50000000 0x36c>;
 		interrupts = <100>;
 		gpmc,num-cs = <8>;
 		gpmc,num-waitpins = <2>;
 		#address-cells = <2>;
 		#size-cells = <1>;
-		ranges = <0 0 0x08000000 0x2000>;	/* CS0: NAND */
+		ranges = <0 0 0x08000000 0x1000000>;	/* CS0 space, 16MB */
 		elm_id = <&elm>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
 
 		nand@0,0 {
-			reg = <0 0 0>; /* CS0, offset 0 */
+			compatible = "ti,omap2-nand";
+			reg = <0 0 4>;		/* CS0, offset 0, NAND I/O window 4 */
+			interrupt-parent = <&gpmc>;
+			interrupts = <0 IRQ_TYPE_NONE>, <1 IRQ_TYPE NONE>;
 			nand-bus-width = <16>;
 			ti,nand-ecc-opt = "bch8";
 			ti,nand-xfer-type = "polled";
+			rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
 
 			gpmc,sync-clk-ps = <0>;
 			gpmc,cs-on-ns = <0>;

Documentation/devicetree/bindings/mtd/nand.txt

-* MTD generic binding
+* NAND chip and NAND controller generic binding
+
+NAND controller/NAND chip representation:
+
+The NAND controller should be represented with its own DT node, and all
+NAND chips attached to this controller should be defined as children nodes
+of the NAND controller. This representation should be enforced even for
+simple controllers supporting only one chip.
+
+Mandatory NAND controller properties:
+- #address-cells: depends on your controller. Should at least be 1 to
+		  encode the CS line id.
+- #size-cells: depends on your controller. Put zero unless you need a
+	       mapping between CS lines and dedicated memory regions
+
+Optional NAND controller properties
+- ranges: only needed if you need to define a mapping between CS lines and
+	  memory regions
+
+Optional NAND chip properties:
 
 - nand-ecc-mode : String, operation mode of the NAND ecc mode.
-  Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first",
-  "soft_bch".
+		  Supported values are: "none", "soft", "hw", "hw_syndrome",
+		  "hw_oob_first".
+		  Deprecated values:
+		  "soft_bch": use "soft" and nand-ecc-algo instead
+- nand-ecc-algo: string, algorithm of NAND ECC.
+		 Supported values are: "hamming", "bch".
 - nand-bus-width : 8 or 16 bus width if not present 8
 - nand-on-flash-bbt: boolean to enable on flash bbt option if not present false
 
@@ -19,3 +42,19 @@ errors per {size} bytes".
 The interpretation of these parameters is implementation-defined, so not all
 implementations must support all possible combinations. However, implementations
 are encouraged to further specify the value(s) they support.
+
+Example:
+
+	nand-controller {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* controller specific properties */
+
+		nand@0 {
+			reg = <0>;
+			nand-ecc-mode = "soft_bch";
+
+			/* controller specific properties */
+		};
+	};

arch/arm/mach-omap2/gpmc-nand.c

@@ -97,10 +97,7 @@ int gpmc_nand_init(struct omap_nand_platform_data *gpmc_nand_data,
 	gpmc_nand_res[2].start = gpmc_get_client_irq(GPMC_IRQ_COUNT_EVENT);
 
 	memset(&s, 0, sizeof(struct gpmc_settings));
-	if (gpmc_nand_data->of_node)
-		gpmc_read_settings_dt(gpmc_nand_data->of_node, &s);
-	else
-		gpmc_set_legacy(gpmc_nand_data, &s);
+	gpmc_set_legacy(gpmc_nand_data, &s);
 
 	s.device_nand = true;
 
@@ -121,8 +118,6 @@ int gpmc_nand_init(struct omap_nand_platform_data *gpmc_nand_data,
 	if (err < 0)
 		goto out_free_cs;
 
-	gpmc_update_nand_reg(&gpmc_nand_data->reg, gpmc_nand_data->cs);
-
 	if (!gpmc_hwecc_bch_capable(gpmc_nand_data->ecc_opt)) {
 		pr_err("omap2-nand: Unsupported NAND ECC scheme selected\n");
 		err = -EINVAL;

arch/arm/mach-pxa/spitz.c

@@ -763,14 +763,49 @@ static struct nand_bbt_descr spitz_nand_bbt = {
 	.pattern	= scan_ff_pattern
 };
 
-static struct nand_ecclayout akita_oobinfo = {
-	.oobfree	= { {0x08, 0x09} },
-	.eccbytes	= 24,
-	.eccpos		= {
-			0x05, 0x01, 0x02, 0x03, 0x06, 0x07, 0x15, 0x11,
-			0x12, 0x13, 0x16, 0x17, 0x25, 0x21, 0x22, 0x23,
-			0x26, 0x27, 0x35, 0x31, 0x32, 0x33, 0x36, 0x37,
-	},
+static int akita_ooblayout_ecc(struct mtd_info *mtd, int section,
+			       struct mtd_oob_region *oobregion)
+{
+	if (section > 12)
+		return -ERANGE;
+
+	switch (section % 3) {
+	case 0:
+		oobregion->offset = 5;
+		oobregion->length = 1;
+		break;
+
+	case 1:
+		oobregion->offset = 1;
+		oobregion->length = 3;
+		break;
+
+	case 2:
+		oobregion->offset = 6;
+		oobregion->length = 2;
+		break;
+	}
+
+	oobregion->offset += (section / 3) * 0x10;
+
+	return 0;
+}
+
+static int akita_ooblayout_free(struct mtd_info *mtd, int section,
+				struct mtd_oob_region *oobregion)
+{
+	if (section)
+		return -ERANGE;
+
+	oobregion->offset = 8;
+	oobregion->length = 9;
+
+	return 0;
+}
+
+static const struct mtd_ooblayout_ops akita_ooblayout_ops = {
+	.ecc = akita_ooblayout_ecc,
+	.free = akita_ooblayout_free,
 };
 
 static struct sharpsl_nand_platform_data spitz_nand_pdata = {
@@ -804,11 +839,11 @@ static void __init spitz_nand_init(void)
 	} else if (machine_is_akita()) {
 		spitz_nand_partitions[1].size = 58 * 1024 * 1024;
 		spitz_nand_bbt.len = 1;
-		spitz_nand_pdata.ecc_layout = &akita_oobinfo;
+		spitz_nand_pdata.ecc_layout = &akita_ooblayout_ops;
 	} else if (machine_is_borzoi()) {
 		spitz_nand_partitions[1].size = 32 * 1024 * 1024;
 		spitz_nand_bbt.len = 1;
-		spitz_nand_pdata.ecc_layout = &akita_oobinfo;
+		spitz_nand_pdata.ecc_layout = &akita_ooblayout_ops;
 	}
 
 	platform_device_register(&spitz_nand_device);

arch/cris/arch-v32/drivers/mach-a3/nandflash.c

@@ -157,6 +157,7 @@ struct mtd_info *__init crisv32_nand_flash_probe(void)
 	/* 20 us command delay time */
 	this->chip_delay = 20;
 	this->ecc.mode = NAND_ECC_SOFT;
+	this->ecc.algo = NAND_ECC_HAMMING;
 
 	/* Enable the following for a flash based bad block table */
 	/* this->bbt_options = NAND_BBT_USE_FLASH; */

arch/cris/arch-v32/drivers/mach-fs/nandflash.c

@@ -148,6 +148,7 @@ struct mtd_info *__init crisv32_nand_flash_probe(void)
 	/* 20 us command delay time */
 	this->chip_delay = 20;
 	this->ecc.mode = NAND_ECC_SOFT;
+	this->ecc.algo = NAND_ECC_HAMMING;
 
 	/* Enable the following for a flash based bad block table */
 	/* this->bbt_options = NAND_BBT_USE_FLASH; */

arch/mips/include/asm/mach-jz4740/jz4740_nand.h

@@ -27,7 +27,7 @@ struct jz_nand_platform_data {
 
 	unsigned char banks[JZ_NAND_NUM_BANKS];
 
-	void (*ident_callback)(struct platform_device *, struct nand_chip *,
+	void (*ident_callback)(struct platform_device *, struct mtd_info *,
 				struct mtd_partition **, int *num_partitions);
 };
 

arch/mips/jz4740/board-qi_lb60.c

@@ -50,20 +50,6 @@ static bool is_avt2;
 #define QI_LB60_GPIO_KEYIN8		JZ_GPIO_PORTD(26)
 
 /* NAND */
-static struct nand_ecclayout qi_lb60_ecclayout_1gb = {
-	.eccbytes = 36,
-	.eccpos = {
-		6,  7,	8,  9,	10, 11, 12, 13,
-		14, 15, 16, 17, 18, 19, 20, 21,
-		22, 23, 24, 25, 26, 27, 28, 29,
-		30, 31, 32, 33, 34, 35, 36, 37,
-		38, 39, 40, 41
-	},
-	.oobfree = {
-		{ .offset = 2, .length = 4 },
-		{ .offset = 42, .length = 22 }
-	},
-};
 
 /* Early prototypes of the QI LB60 had only 1GB of NAND.
  * In order to support these devices as well the partition and ecc layout is
@@ -86,25 +72,6 @@ static struct mtd_partition qi_lb60_partitions_1gb[] = {
 	},
 };
 
-static struct nand_ecclayout qi_lb60_ecclayout_2gb = {
-	.eccbytes = 72,
-	.eccpos = {
-		12, 13, 14, 15, 16, 17, 18, 19,
-		20, 21, 22, 23, 24, 25, 26, 27,
-		28, 29, 30, 31, 32, 33, 34, 35,
-		36, 37, 38, 39, 40, 41, 42, 43,
-		44, 45, 46, 47, 48, 49, 50, 51,
-		52, 53, 54, 55, 56, 57, 58, 59,
-		60, 61, 62, 63, 64, 65, 66, 67,
-		68, 69, 70, 71, 72, 73, 74, 75,
-		76, 77, 78, 79, 80, 81, 82, 83
-	},
-	.oobfree = {
-		{ .offset = 2, .length = 10 },
-		{ .offset = 84, .length = 44 },
-	},
-};
-
 static struct mtd_partition qi_lb60_partitions_2gb[] = {
 	{
 		.name = "NAND BOOT partition",
@@ -123,19 +90,67 @@ static struct mtd_partition qi_lb60_partitions_2gb[] = {
 	},
 };
 
+static int qi_lb60_ooblayout_ecc(struct mtd_info *mtd, int section,
+				 struct mtd_oob_region *oobregion)
+{
+	if (section)
+		return -ERANGE;
+
+	oobregion->length = 36;
+	oobregion->offset = 6;
+
+	if (mtd->oobsize == 128) {
+		oobregion->length *= 2;
+		oobregion->offset *= 2;
+	}
+
+	return 0;
+}
+
+static int qi_lb60_ooblayout_free(struct mtd_info *mtd, int section,
+				  struct mtd_oob_region *oobregion)
+{
+	int eccbytes = 36, eccoff = 6;
+
+	if (section > 1)
+		return -ERANGE;
+
+	if (mtd->oobsize == 128) {
+		eccbytes *= 2;
+		eccoff *= 2;
+	}
+
+	if (!section) {
+		oobregion->offset = 2;
+		oobregion->length = eccoff - 2;
+	} else {
+		oobregion->offset = eccoff + eccbytes;
+		oobregion->length = mtd->oobsize - oobregion->offset;
+	}
+
+	return 0;
+}
+
+static const struct mtd_ooblayout_ops qi_lb60_ooblayout_ops = {
+	.ecc = qi_lb60_ooblayout_ecc,
+	.free = qi_lb60_ooblayout_free,
+};
+
 static void qi_lb60_nand_ident(struct platform_device *pdev,
-		struct nand_chip *chip, struct mtd_partition **partitions,
+		struct mtd_info *mtd, struct mtd_partition **partitions,
 		int *num_partitions)
 {
+	struct nand_chip *chip = mtd_to_nand(mtd);
+
 	if (chip->page_shift == 12) {
-		chip->ecc.layout = &qi_lb60_ecclayout_2gb;
 		*partitions = qi_lb60_partitions_2gb;
 		*num_partitions = ARRAY_SIZE(qi_lb60_partitions_2gb);
 	} else {
-		chip->ecc.layout = &qi_lb60_ecclayout_1gb;
 		*partitions = qi_lb60_partitions_1gb;
 		*num_partitions = ARRAY_SIZE(qi_lb60_partitions_1gb);
 	}
+
+	mtd_set_ooblayout(mtd, &qi_lb60_ooblayout_ops);
 }
 
 static struct jz_nand_platform_data qi_lb60_nand_pdata = {

drivers/leds/trigger/Kconfig

@@ -41,6 +41,14 @@ config LEDS_TRIGGER_IDE_DISK
 	  This allows LEDs to be controlled by IDE disk activity.
 	  If unsure, say Y.
 
+config LEDS_TRIGGER_MTD
+	bool "LED MTD (NAND/NOR) Trigger"
+	depends on MTD
+	depends on LEDS_TRIGGERS
+	help
+	  This allows LEDs to be controlled by MTD activity.
+	  If unsure, say N.
+
 config LEDS_TRIGGER_HEARTBEAT
 	tristate "LED Heartbeat Trigger"
 	depends on LEDS_TRIGGERS
@@ -108,4 +116,11 @@ config LEDS_TRIGGER_CAMERA
 	  This enables direct flash/torch on/off by the driver, kernel space.
 	  If unsure, say Y.
 
+config LEDS_TRIGGER_PANIC
+	bool "LED Panic Trigger"
+	depends on LEDS_TRIGGERS
+	help
+	  This allows LEDs to be configured to blink on a kernel panic.
+	  If unsure, say Y.
+
 endif # LEDS_TRIGGERS

drivers/leds/trigger/Makefile

 obj-$(CONFIG_LEDS_TRIGGER_TIMER)	+= ledtrig-timer.o
 obj-$(CONFIG_LEDS_TRIGGER_ONESHOT)	+= ledtrig-oneshot.o
 obj-$(CONFIG_LEDS_TRIGGER_IDE_DISK)	+= ledtrig-ide-disk.o
+obj-$(CONFIG_LEDS_TRIGGER_MTD)		+= ledtrig-mtd.o
 obj-$(CONFIG_LEDS_TRIGGER_HEARTBEAT)	+= ledtrig-heartbeat.o
 obj-$(CONFIG_LEDS_TRIGGER_BACKLIGHT)	+= ledtrig-backlight.o
 obj-$(CONFIG_LEDS_TRIGGER_GPIO)		+= ledtrig-gpio.o
@@ -8,3 +9,4 @@ obj-$(CONFIG_LEDS_TRIGGER_CPU)		+= ledtrig-cpu.o
 obj-$(CONFIG_LEDS_TRIGGER_DEFAULT_ON)	+= ledtrig-default-on.o
 obj-$(CONFIG_LEDS_TRIGGER_TRANSIENT)	+= ledtrig-transient.o
 obj-$(CONFIG_LEDS_TRIGGER_CAMERA)	+= ledtrig-camera.o
+obj-$(CONFIG_LEDS_TRIGGER_PANIC)	+= ledtrig-panic.o

drivers/leds/trigger/ledtrig-mtd.c

+/*
+ * LED MTD trigger
+ *
+ * Copyright 2016 Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
+ *
+ * Based on LED IDE-Disk Activity Trigger
+ *
+ * Copyright 2006 Openedhand Ltd.
+ *
+ * Author: Richard Purdie <rpurdie@openedhand.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/leds.h>
+
+#define BLINK_DELAY 30
+
+DEFINE_LED_TRIGGER(ledtrig_mtd);
+DEFINE_LED_TRIGGER(ledtrig_nand);
+
+void ledtrig_mtd_activity(void)
+{
+	unsigned long blink_delay = BLINK_DELAY;
+
+	led_trigger_blink_oneshot(ledtrig_mtd,
+				  &blink_delay, &blink_delay, 0);
+	led_trigger_blink_oneshot(ledtrig_nand,
+				  &blink_delay, &blink_delay, 0);
+}
+EXPORT_SYMBOL(ledtrig_mtd_activity);
+
+static int __init ledtrig_mtd_init(void)
+{
+	led_trigger_register_simple("mtd", &ledtrig_mtd);
+	led_trigger_register_simple("nand-disk", &ledtrig_nand);
+
+	return 0;
+}
+device_initcall(ledtrig_mtd_init);

drivers/leds/trigger/ledtrig-panic.c

+/*
+ * Kernel Panic LED Trigger
+ *
+ * Copyright 2016 Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/leds.h>
+
+static struct led_trigger *trigger;
+
+static long led_panic_blink(int state)
+{
+	led_trigger_event(trigger, state ? LED_FULL : LED_OFF);
+	return 0;
+}
+
+static int __init ledtrig_panic_init(void)
+{
+	led_trigger_register_simple("panic", &trigger);
+	panic_blink = led_panic_blink;
+	return 0;
+}
+device_initcall(ledtrig_panic_init);

drivers/memory/Kconfig

@@ -51,6 +51,7 @@ config TI_EMIF
 
 config OMAP_GPMC
 	bool
+	select GPIOLIB
 	help
 	  This driver is for the General Purpose Memory Controller (GPMC)
 	  present on Texas Instruments SoCs (e.g. OMAP2+). GPMC allows

drivers/memory/fsl_ifc.c

@@ -59,11 +59,11 @@ int fsl_ifc_find(phys_addr_t addr_base)
 {
 	int i = 0;
 
-	if (!fsl_ifc_ctrl_dev || !fsl_ifc_ctrl_dev->regs)
+	if (!fsl_ifc_ctrl_dev || !fsl_ifc_ctrl_dev->gregs)
 		return -ENODEV;
 
 	for (i = 0; i < fsl_ifc_ctrl_dev->banks; i++) {
-		u32 cspr = ifc_in32(&fsl_ifc_ctrl_dev->regs->cspr_cs[i].cspr);
+		u32 cspr = ifc_in32(&fsl_ifc_ctrl_dev->gregs->cspr_cs[i].cspr);
 		if (cspr & CSPR_V && (cspr & CSPR_BA) ==
 				convert_ifc_address(addr_base))
 			return i;
@@ -75,7 +75,7 @@ EXPORT_SYMBOL(fsl_ifc_find);
 
 static int fsl_ifc_ctrl_init(struct fsl_ifc_ctrl *ctrl)
 {
-	struct fsl_ifc_regs __iomem *ifc = ctrl->regs;
+	struct fsl_ifc_global __iomem *ifc = ctrl->gregs;
 
 	/*
 	 * Clear all the common status and event registers
@@ -104,7 +104,7 @@ static int fsl_ifc_ctrl_remove(struct platform_device *dev)
 	irq_dispose_mapping(ctrl->nand_irq);
 	irq_dispose_mapping(ctrl->irq);
 
-	iounmap(ctrl->regs);
+	iounmap(ctrl->gregs);
 
 	dev_set_drvdata(&dev->dev, NULL);
 	kfree(ctrl);
@@ -122,7 +122,7 @@ static DEFINE_SPINLOCK(nand_irq_lock);
 
 static u32 check_nand_stat(struct fsl_ifc_ctrl *ctrl)
 {
-	struct fsl_ifc_regs __iomem *ifc = ctrl->regs;
+	struct fsl_ifc_runtime __iomem *ifc = ctrl->rregs;
 	unsigned long flags;
 	u32 stat;
 
@@ -157,7 +157,7 @@ static irqreturn_t fsl_ifc_nand_irq(int irqno, void *data)
 static irqreturn_t fsl_ifc_ctrl_irq(int irqno, void *data)
 {
 	struct fsl_ifc_ctrl *ctrl = data;
-	struct fsl_ifc_regs __iomem *ifc = ctrl->regs;
+	struct fsl_ifc_global __iomem *ifc = ctrl->gregs;
 	u32 err_axiid, err_srcid, status, cs_err, err_addr;
 	irqreturn_t ret = IRQ_NONE;
 
@@ -215,6 +215,7 @@ static int fsl_ifc_ctrl_probe(struct platform_device *dev)
 {
 	int ret = 0;
 	int version, banks;
+	void __iomem *addr;
 
 	dev_info(&dev->dev, "Freescale Integrated Flash Controller\n");
 
@@ -225,22 +226,13 @@ static int fsl_ifc_ctrl_probe(struct platform_device *dev)
 	dev_set_drvdata(&dev->dev, fsl_ifc_ctrl_dev);
 
 	/* IOMAP the entire IFC region */
-	fsl_ifc_ctrl_dev->regs = of_iomap(dev->dev.of_node, 0);
-	if (!fsl_ifc_ctrl_dev->regs) {
+	fsl_ifc_ctrl_dev->gregs = of_iomap(dev->dev.of_node, 0);
+	if (!fsl_ifc_ctrl_dev->gregs) {
 		dev_err(&dev->dev, "failed to get memory region\n");
 		ret = -ENODEV;
 		goto err;
 	}
 
-	version = ifc_in32(&fsl_ifc_ctrl_dev->regs->ifc_rev) &
-			FSL_IFC_VERSION_MASK;
-	banks = (version == FSL_IFC_VERSION_1_0_0) ? 4 : 8;
-	dev_info(&dev->dev, "IFC version %d.%d, %d banks\n",
-		version >> 24, (version >> 16) & 0xf, banks);
-
-	fsl_ifc_ctrl_dev->version = version;
-	fsl_ifc_ctrl_dev->banks = banks;
-
 	if (of_property_read_bool(dev->dev.of_node, "little-endian")) {
 		fsl_ifc_ctrl_dev->little_endian = true;
 		dev_dbg(&dev->dev, "IFC REGISTERS are LITTLE endian\n");
@@ -249,8 +241,9 @@ static int fsl_ifc_ctrl_probe(struct platform_device *dev)
 		dev_dbg(&dev->dev, "IFC REGISTERS are BIG endian\n");
 	}
 
-	version = ioread32be(&fsl_ifc_ctrl_dev->regs->ifc_rev) &
+	version = ifc_in32(&fsl_ifc_ctrl_dev->gregs->ifc_rev) &
 			FSL_IFC_VERSION_MASK;
+
 	banks = (version == FSL_IFC_VERSION_1_0_0) ? 4 : 8;
 	dev_info(&dev->dev, "IFC version %d.%d, %d banks\n",
 		version >> 24, (version >> 16) & 0xf, banks);
@@ -258,6 +251,13 @@ static int fsl_ifc_ctrl_probe(struct platform_device *dev)
 	fsl_ifc_ctrl_dev->version = version;
 	fsl_ifc_ctrl_dev->banks = banks;
 
+	addr = fsl_ifc_ctrl_dev->gregs;
+	if (version >= FSL_IFC_VERSION_2_0_0)
+		addr += PGOFFSET_64K;
+	else
+		addr += PGOFFSET_4K;
+	fsl_ifc_ctrl_dev->rregs = addr;
+
 	/* get the Controller level irq */
 	fsl_ifc_ctrl_dev->irq = irq_of_parse_and_map(dev->dev.of_node, 0);
 	if (fsl_ifc_ctrl_dev->irq == 0) {

drivers/mtd/devices/docg3.c

@@ -67,16 +67,40 @@ module_param(reliable_mode, uint, 0);
 MODULE_PARM_DESC(reliable_mode, "Set the docg3 mode (0=normal MLC, 1=fast, "
 		 "2=reliable) : MLC normal operations are in normal mode");
 
-/**
- * struct docg3_oobinfo - DiskOnChip G3 OOB layout
- * @eccbytes: 8 bytes are used (1 for Hamming ECC, 7 for BCH ECC)
- * @eccpos: ecc positions (byte 7 is Hamming ECC, byte 8-14 are BCH ECC)
- * @oobfree: free pageinfo bytes (byte 0 until byte 6, byte 15
- */
-static struct nand_ecclayout docg3_oobinfo = {
-	.eccbytes = 8,
-	.eccpos = {7, 8, 9, 10, 11, 12, 13, 14},
-	.oobfree = {{0, 7}, {15, 1} },
+static int docg3_ooblayout_ecc(struct mtd_info *mtd, int section,
+			       struct mtd_oob_region *oobregion)
+{
+	if (section)
+		return -ERANGE;
+
+	/* byte 7 is Hamming ECC, byte 8-14 are BCH ECC */
+	oobregion->offset = 7;
+	oobregion->length = 8;
+
+	return 0;
+}
+
+static int docg3_ooblayout_free(struct mtd_info *mtd, int section,
+				struct mtd_oob_region *oobregion)
+{
+	if (section > 1)
+		return -ERANGE;
+
+	/* free bytes: byte 0 until byte 6, byte 15 */
+	if (!section) {
+		oobregion->offset = 0;
+		oobregion->length = 7;
+	} else {
+		oobregion->offset = 15;
+		oobregion->length = 1;
+	}
+
+	return 0;
+}
+
+static const struct mtd_ooblayout_ops nand_ooblayout_docg3_ops = {
+	.ecc = docg3_ooblayout_ecc,
+	.free = docg3_ooblayout_free,
 };
 
 static inline u8 doc_readb(struct docg3 *docg3, u16 reg)
@@ -1857,7 +1881,7 @@ static int __init doc_set_driver_info(int chip_id, struct mtd_info *mtd)
 	mtd->_read_oob = doc_read_oob;
 	mtd->_write_oob = doc_write_oob;
 	mtd->_block_isbad = doc_block_isbad;
-	mtd->ecclayout = &docg3_oobinfo;
+	mtd_set_ooblayout(mtd, &nand_ooblayout_docg3_ops);
 	mtd->oobavail = 8;
 	mtd->ecc_strength = DOC_ECC_BCH_T;
 

drivers/mtd/mtdchar.c

@@ -465,35 +465,108 @@ static int mtdchar_readoob(struct file *file, struct mtd_info *mtd,
 }
 
 /*
- * Copies (and truncates, if necessary) data from the larger struct,
- * nand_ecclayout, to the smaller, deprecated layout struct,
- * nand_ecclayout_user. This is necessary only to support the deprecated
- * API ioctl ECCGETLAYOUT while allowing all new functionality to use
- * nand_ecclayout flexibly (i.e. the struct may change size in new
- * releases without requiring major rewrites).
+ * Copies (and truncates, if necessary) OOB layout information to the
+ * deprecated layout struct, nand_ecclayout_user. This is necessary only to
+ * support the deprecated API ioctl ECCGETLAYOUT while allowing all new
+ * functionality to use mtd_ooblayout_ops flexibly (i.e. mtd_ooblayout_ops
+ * can describe any kind of OOB layout with almost zero overhead from a
+ * memory usage point of view).
  */
-static int shrink_ecclayout(const struct nand_ecclayout *from,
-		struct nand_ecclayout_user *to)
+static int shrink_ecclayout(struct mtd_info *mtd,
+			    struct nand_ecclayout_user *to)
 {
-	int i;
+	struct mtd_oob_region oobregion;
+	int i, section = 0, ret;
 
-	if (!from || !to)
+	if (!mtd || !to)
 		return -EINVAL;
 
 	memset(to, 0, sizeof(*to));
 
-	to->eccbytes = min((int)from->eccbytes, MTD_MAX_ECCPOS_ENTRIES);
-	for (i = 0; i < to->eccbytes; i++)
-		to->eccpos[i] = from->eccpos[i];
+	to->eccbytes = 0;
+	for (i = 0; i < MTD_MAX_ECCPOS_ENTRIES;) {
+		u32 eccpos;
+
+		ret = mtd_ooblayout_ecc(mtd, section, &oobregion);
+		if (ret < 0) {
+			if (ret != -ERANGE)
+				return ret;
+
+			break;
+		}
+
+		eccpos = oobregion.offset;
+		for (; i < MTD_MAX_ECCPOS_ENTRIES &&
+		       eccpos < oobregion.offset + oobregion.length; i++) {
+			to->eccpos[i] = eccpos++;
+			to->eccbytes++;
+		}
+	}
 
 	for (i = 0; i < MTD_MAX_OOBFREE_ENTRIES; i++) {
-		if (from->oobfree[i].length == 0 &&
-				from->oobfree[i].offset == 0)
+		ret = mtd_ooblayout_free(mtd, i, &oobregion);
+		if (ret < 0) {
+			if (ret != -ERANGE)
+				return ret;
+
+			break;
+		}
+
+		to->oobfree[i].offset = oobregion.offset;
+		to->oobfree[i].length = oobregion.length;
+		to->oobavail += to->oobfree[i].length;
+	}
+
+	return 0;
+}
+
+static int get_oobinfo(struct mtd_info *mtd, struct nand_oobinfo *to)
+{
+	struct mtd_oob_region oobregion;
+	int i, section = 0, ret;
+
+	if (!mtd || !to)
+		return -EINVAL;
+
+	memset(to, 0, sizeof(*to));
+
+	to->eccbytes = 0;
+	for (i = 0; i < ARRAY_SIZE(to->eccpos);) {
+		u32 eccpos;
+
+		ret = mtd_ooblayout_ecc(mtd, section, &oobregion);
+		if (ret < 0) {
+			if (ret != -ERANGE)
+				return ret;
+
 			break;
-		to->oobavail += from->oobfree[i].length;
-		to->oobfree[i] = from->oobfree[i];
+		}
+
+		if (oobregion.length + i > ARRAY_SIZE(to->eccpos))
+			return -EINVAL;
+
+		eccpos = oobregion.offset;
+		for (; eccpos < oobregion.offset + oobregion.length; i++) {
+			to->eccpos[i] = eccpos++;
+			to->eccbytes++;
+		}
 	}
 
+	for (i = 0; i < 8; i++) {
+		ret = mtd_ooblayout_free(mtd, i, &oobregion);
+		if (ret < 0) {
+			if (ret != -ERANGE)
+				return ret;
+
+			break;
+		}
+
+		to->oobfree[i][0] = oobregion.offset;
+		to->oobfree[i][1] = oobregion.length;
+	}
+
+	to->useecc = MTD_NANDECC_AUTOPLACE;
+
 	return 0;
 }
 
@@ -815,16 +888,12 @@ static int mtdchar_ioctl(struct file *file, u_int cmd, u_long arg)
 	{
 		struct nand_oobinfo oi;
 
-		if (!mtd->ecclayout)
+		if (!mtd->ooblayout)
 			return -EOPNOTSUPP;
-		if (mtd->ecclayout->eccbytes > ARRAY_SIZE(oi.eccpos))
-			return -EINVAL;
 
-		oi.useecc = MTD_NANDECC_AUTOPLACE;
-		memcpy(&oi.eccpos, mtd->ecclayout->eccpos, sizeof(oi.eccpos));
-		memcpy(&oi.oobfree, mtd->ecclayout->oobfree,
-		       sizeof(oi.oobfree));
-		oi.eccbytes = mtd->ecclayout->eccbytes;
+		ret = get_oobinfo(mtd, &oi);
+		if (ret)
+			return ret;
 
 		if (copy_to_user(argp, &oi, sizeof(struct nand_oobinfo)))
 			return -EFAULT;
@@ -913,14 +982,14 @@ static int mtdchar_ioctl(struct file *file, u_int cmd, u_long arg)
 	{
 		struct nand_ecclayout_user *usrlay;
 
-		if (!mtd->ecclayout)
+		if (!mtd->ooblayout)
 			return -EOPNOTSUPP;
 
 		usrlay = kmalloc(sizeof(*usrlay), GFP_KERNEL);
 		if (!usrlay)
 			return -ENOMEM;
 
-		shrink_ecclayout(mtd->ecclayout, usrlay);
+		shrink_ecclayout(mtd, usrlay);
 
 		if (copy_to_user(argp, usrlay, sizeof(*usrlay)))
 			ret = -EFAULT;

drivers/mtd/mtdconcat.c

@@ -777,7 +777,7 @@ struct mtd_info *mtd_concat_create(struct mtd_info *subdev[],	/* subdevices to c
 
 	}
 
-	concat->mtd.ecclayout = subdev[0]->ecclayout;
+	mtd_set_ooblayout(&concat->mtd, subdev[0]->ooblayout);
 
 	concat->num_subdev = num_devs;
 	concat->mtd.name = name;

drivers/mtd/mtdpart.c

@@ -317,6 +317,27 @@ static int part_block_markbad(struct mtd_info *mtd, loff_t ofs)
 	return res;
 }
 
+static int part_ooblayout_ecc(struct mtd_info *mtd, int section,
+			      struct mtd_oob_region *oobregion)
+{
+	struct mtd_part *part = mtd_to_part(mtd);
+
+	return mtd_ooblayout_ecc(part->master, section, oobregion);
+}
+
+static int part_ooblayout_free(struct mtd_info *mtd, int section,
+			       struct mtd_oob_region *oobregion)
+{
+	struct mtd_part *part = mtd_to_part(mtd);
+
+	return mtd_ooblayout_free(part->master, section, oobregion);
+}
+
+static const struct mtd_ooblayout_ops part_ooblayout_ops = {
+	.ecc = part_ooblayout_ecc,
+	.free = part_ooblayout_free,
+};
+
 static inline void free_partition(struct mtd_part *p)
 {
 	kfree(p->mtd.name);
@@ -533,7 +554,7 @@ static struct mtd_part *allocate_partition(struct mtd_info *master,
 			part->name);
 	}
 
-	slave->mtd.ecclayout = master->ecclayout;
+	mtd_set_ooblayout(&slave->mtd, &part_ooblayout_ops);
 	slave->mtd.ecc_step_size = master->ecc_step_size;
 	slave->mtd.ecc_strength = master->ecc_strength;
 	slave->mtd.bitflip_threshold = master->bitflip_threshold;

drivers/mtd/nand/ams-delta.c

@@ -224,6 +224,7 @@ static int ams_delta_init(struct platform_device *pdev)
 	/* 25 us command delay time */
 	this->chip_delay = 30;
 	this->ecc.mode = NAND_ECC_SOFT;
+	this->ecc.algo = NAND_ECC_HAMMING;
 
 	platform_set_drvdata(pdev, io_base);
 

drivers/mtd/nand/au1550nd.c

@@ -459,6 +459,7 @@ static int au1550nd_probe(struct platform_device *pdev)
 	/* 30 us command delay time */
 	this->chip_delay = 30;
 	this->ecc.mode = NAND_ECC_SOFT;
+	this->ecc.algo = NAND_ECC_HAMMING;
 
 	if (pd->devwidth)
 		this->options |= NAND_BUSWIDTH_16;

drivers/mtd/nand/bf5xx_nand.c

@@ -109,28 +109,33 @@ static const unsigned short bfin_nfc_pin_req[] =
 	 0};
 
 #ifdef CONFIG_MTD_NAND_BF5XX_BOOTROM_ECC
-static struct nand_ecclayout bootrom_ecclayout = {
-	.eccbytes = 24,
-	.eccpos = {
-		0x8 * 0, 0x8 * 0 + 1, 0x8 * 0 + 2,
-		0x8 * 1, 0x8 * 1 + 1, 0x8 * 1 + 2,
-		0x8 * 2, 0x8 * 2 + 1, 0x8 * 2 + 2,
-		0x8 * 3, 0x8 * 3 + 1, 0x8 * 3 + 2,
-		0x8 * 4, 0x8 * 4 + 1, 0x8 * 4 + 2,
-		0x8 * 5, 0x8 * 5 + 1, 0x8 * 5 + 2,
-		0x8 * 6, 0x8 * 6 + 1, 0x8 * 6 + 2,
-		0x8 * 7, 0x8 * 7 + 1, 0x8 * 7 + 2
-	},
-	.oobfree = {
-		{ 0x8 * 0 + 3, 5 },
-		{ 0x8 * 1 + 3, 5 },
-		{ 0x8 * 2 + 3, 5 },
-		{ 0x8 * 3 + 3, 5 },
-		{ 0x8 * 4 + 3, 5 },
-		{ 0x8 * 5 + 3, 5 },
-		{ 0x8 * 6 + 3, 5 },
-		{ 0x8 * 7 + 3, 5 },
-	}
+static int bootrom_ooblayout_ecc(struct mtd_info *mtd, int section,
+				 struct mtd_oob_region *oobregion)
+{
+	if (section > 7)
+		return -ERANGE;
+
+	oobregion->offset = section * 8;
+	oobregion->length = 3;
+
+	return 0;
+}
+
+static int bootrom_ooblayout_free(struct mtd_info *mtd, int section,
+				  struct mtd_oob_region *oobregion)
+{
+	if (section > 7)
+		return -ERANGE;
+
+	oobregion->offset = (section * 8) + 3;
+	oobregion->length = 5;
+
+	return 0;
+}
+
+static const struct mtd_ooblayout_ops bootrom_ooblayout_ops = {
+	.ecc = bootrom_ooblayout_ecc,
+	.free = bootrom_ooblayout_free,
 };
 #endif
 
@@ -800,7 +805,7 @@ static int bf5xx_nand_probe(struct platform_device *pdev)
 	/* setup hardware ECC data struct */
 	if (hardware_ecc) {
 #ifdef CONFIG_MTD_NAND_BF5XX_BOOTROM_ECC
-		chip->ecc.layout = &bootrom_ecclayout;
+		mtd_set_ooblayout(mtd, &bootrom_ooblayout_ops);
 #endif
 		chip->read_buf      = bf5xx_nand_dma_read_buf;
 		chip->write_buf     = bf5xx_nand_dma_write_buf;
@@ -812,6 +817,7 @@ static int bf5xx_nand_probe(struct platform_device *pdev)
 		chip->ecc.write_page_raw = bf5xx_nand_write_page_raw;
 	} else {
 		chip->ecc.mode	    = NAND_ECC_SOFT;
+		chip->ecc.algo	= NAND_ECC_HAMMING;
 	}
 
 	/* scan hardware nand chip and setup mtd info data struct */

drivers/mtd/nand/cafe_nand.c

@@ -459,10 +459,37 @@ static int cafe_nand_read_page(struct mtd_info *mtd, struct nand_chip *chip,
 	return max_bitflips;
 }
 
-static struct nand_ecclayout cafe_oobinfo_2048 = {
-	.eccbytes = 14,
-	.eccpos = { 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13},
-	.oobfree = {{14, 50}}
+static int cafe_ooblayout_ecc(struct mtd_info *mtd, int section,
+			      struct mtd_oob_region *oobregion)
+{
+	struct nand_chip *chip = mtd_to_nand(mtd);
+
+	if (section)
+		return -ERANGE;
+
+	oobregion->offset = 0;
+	oobregion->length = chip->ecc.total;
+
+	return 0;
+}
+
+static int cafe_ooblayout_free(struct mtd_info *mtd, int section,
+			       struct mtd_oob_region *oobregion)
+{
+	struct nand_chip *chip = mtd_to_nand(mtd);
+
+	if (section)
+		return -ERANGE;
+
+	oobregion->offset = chip->ecc.total;
+	oobregion->length = mtd->oobsize - chip->ecc.total;
+
+	return 0;
+}
+
+static const struct mtd_ooblayout_ops cafe_ooblayout_ops = {
+	.ecc = cafe_ooblayout_ecc,
+	.free = cafe_ooblayout_free,
 };
 
 /* Ick. The BBT code really ought to be able to work this bit out
@@ -494,12 +521,6 @@ static struct nand_bbt_descr cafe_bbt_mirror_descr_2048 = {
 	.pattern = cafe_mirror_pattern_2048
 };
 
-static struct nand_ecclayout cafe_oobinfo_512 = {
-	.eccbytes = 14,
-	.eccpos = { 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13},
-	.oobfree = {{14, 2}}
-};
-
 static struct nand_bbt_descr cafe_bbt_main_descr_512 = {
 	.options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
 		| NAND_BBT_2BIT | NAND_BBT_VERSION,
@@ -743,12 +764,11 @@ static int cafe_nand_probe(struct pci_dev *pdev,
 		cafe->ctl2 |= 1<<29; /* 2KiB page size */
 
 	/* Set up ECC according to the type of chip we found */
+	mtd_set_ooblayout(mtd, &cafe_ooblayout_ops);
 	if (mtd->writesize == 2048) {
-		cafe->nand.ecc.layout = &cafe_oobinfo_2048;
 		cafe->nand.bbt_td = &cafe_bbt_main_descr_2048;
 		cafe->nand.bbt_md = &cafe_bbt_mirror_descr_2048;
 	} else if (mtd->writesize == 512) {
-		cafe->nand.ecc.layout = &cafe_oobinfo_512;
 		cafe->nand.bbt_td = &cafe_bbt_main_descr_512;
 		cafe->nand.bbt_md = &cafe_bbt_mirror_descr_512;
 	} else {

drivers/mtd/nand/cmx270_nand.c

@@ -187,6 +187,7 @@ static int __init cmx270_init(void)
 	/* 15 us command delay time */
 	this->chip_delay = 20;
 	this->ecc.mode = NAND_ECC_SOFT;
+	this->ecc.algo = NAND_ECC_HAMMING;
 
 	/* read/write functions */
 	this->read_byte = cmx270_read_byte;

drivers/mtd/nand/davinci_nand.c

@@ -34,7 +34,6 @@
 #include <linux/slab.h>
 #include <linux/of_device.h>
 #include <linux/of.h>
-#include <linux/of_mtd.h>
 
 #include <linux/platform_data/mtd-davinci.h>
 #include <linux/platform_data/mtd-davinci-aemif.h>
@@ -54,7 +53,6 @@
  */
 struct davinci_nand_info {
 	struct nand_chip	chip;
-	struct nand_ecclayout	ecclayout;
 
 	struct device		*dev;
 	struct clk		*clk;
@@ -480,63 +478,46 @@ static int nand_davinci_dev_ready(struct mtd_info *mtd)
  * ten ECC bytes plus the manufacturer's bad block marker byte, and
  * and not overlapping the default BBT markers.
  */
-static struct nand_ecclayout hwecc4_small = {
-	.eccbytes = 10,
-	.eccpos = { 0, 1, 2, 3, 4,
-		/* offset 5 holds the badblock marker */
-		6, 7,
-		13, 14, 15, },
-	.oobfree = {
-		{.offset = 8, .length = 5, },
-		{.offset = 16, },
-	},
-};
+static int hwecc4_ooblayout_small_ecc(struct mtd_info *mtd, int section,
+				      struct mtd_oob_region *oobregion)
+{
+	if (section > 2)
+		return -ERANGE;
+
+	if (!section) {
+		oobregion->offset = 0;
+		oobregion->length = 5;
+	} else if (section == 1) {
+		oobregion->offset = 6;
+		oobregion->length = 2;
+	} else {
+		oobregion->offset = 13;
+		oobregion->length = 3;
+	}
 
-/* An ECC layout for using 4-bit ECC with large-page (2048bytes) flash,
- * storing ten ECC bytes plus the manufacturer's bad block marker byte,
- * and not overlapping the default BBT markers.
- */
-static struct nand_ecclayout hwecc4_2048 = {
-	.eccbytes = 40,
-	.eccpos = {
-		/* at the end of spare sector */
-		24, 25, 26, 27, 28, 29,	30, 31, 32, 33,
-		34, 35, 36, 37, 38, 39,	40, 41, 42, 43,
-		44, 45, 46, 47, 48, 49, 50, 51, 52, 53,
-		54, 55, 56, 57, 58, 59, 60, 61, 62, 63,
-		},
-	.oobfree = {
-		/* 2 bytes at offset 0 hold manufacturer badblock markers */
-		{.offset = 2, .length = 22, },
-		/* 5 bytes at offset 8 hold BBT markers */
-		/* 8 bytes at offset 16 hold JFFS2 clean markers */
-	},
-};
+	return 0;
+}
 
-/*
- * An ECC layout for using 4-bit ECC with large-page (4096bytes) flash,
- * storing ten ECC bytes plus the manufacturer's bad block marker byte,
- * and not overlapping the default BBT markers.
- */
-static struct nand_ecclayout hwecc4_4096 = {
-	.eccbytes = 80,
-	.eccpos = {
-		/* at the end of spare sector */
-		48, 49, 50, 51, 52, 53, 54, 55, 56, 57,
-		58, 59, 60, 61, 62, 63, 64, 65, 66, 67,
-		68, 69, 70, 71, 72, 73, 74, 75, 76, 77,
-		78, 79, 80, 81, 82, 83, 84, 85, 86, 87,
-		88, 89, 90, 91, 92, 93, 94, 95, 96, 97,
-		98, 99, 100, 101, 102, 103, 104, 105, 106, 107,
-		108, 109, 110, 111, 112, 113, 114, 115, 116, 117,
-		118, 119, 120, 121, 122, 123, 124, 125, 126, 127,
-	},
-	.oobfree = {
-		/* 2 bytes at offset 0 hold manufacturer badblock markers */
-		{.offset = 2, .length = 46, },
-		/* 5 bytes at offset 8 hold BBT markers */
-		/* 8 bytes at offset 16 hold JFFS2 clean markers */
-	},
+static int hwecc4_ooblayout_small_free(struct mtd_info *mtd, int section,
+				       struct mtd_oob_region *oobregion)
+{
+	if (section > 1)
+		return -ERANGE;
+
+	if (!section) {
+		oobregion->offset = 8;
+		oobregion->length = 5;
+	} else {
+		oobregion->offset = 16;
+		oobregion->length = mtd->oobsize - 16;
+	}
+
+	return 0;
+}
+
+static const struct mtd_ooblayout_ops hwecc4_small_ooblayout_ops = {
+	.ecc = hwecc4_ooblayout_small_ecc,
+	.free = hwecc4_ooblayout_small_free,
 };
 
 #if defined(CONFIG_OF)
@@ -577,8 +558,6 @@ static struct davinci_nand_pdata
 			"ti,davinci-mask-chipsel", &prop))
 			pdata->mask_chipsel = prop;
 		if (!of_property_read_string(pdev->dev.of_node,
-			"nand-ecc-mode", &mode) ||
-		    !of_property_read_string(pdev->dev.of_node,
 			"ti,davinci-ecc-mode", &mode)) {
 			if (!strncmp("none", mode, 4))
 				pdata->ecc_mode = NAND_ECC_NONE;
@@ -591,14 +570,11 @@ static struct davinci_nand_pdata
 			"ti,davinci-ecc-bits", &prop))
 			pdata->ecc_bits = prop;
 
-		prop = of_get_nand_bus_width(pdev->dev.of_node);
-		if (0 < prop || !of_property_read_u32(pdev->dev.of_node,
-			"ti,davinci-nand-buswidth", &prop))
-			if (prop == 16)
-				pdata->options |= NAND_BUSWIDTH_16;
+		if (!of_property_read_u32(pdev->dev.of_node,
+			"ti,davinci-nand-buswidth", &prop) && prop == 16)
+			pdata->options |= NAND_BUSWIDTH_16;
+
 		if (of_property_read_bool(pdev->dev.of_node,
-			"nand-on-flash-bbt") ||
-		    of_property_read_bool(pdev->dev.of_node,
 			"ti,davinci-nand-use-bbt"))
 			pdata->bbt_options = NAND_BBT_USE_FLASH;
 
@@ -628,7 +604,6 @@ static int nand_davinci_probe(struct platform_device *pdev)
 	void __iomem			*base;
 	int				ret;
 	uint32_t			val;
-	nand_ecc_modes_t		ecc_mode;
 	struct mtd_info			*mtd;
 
 	pdata = nand_davinci_get_pdata(pdev);
@@ -712,13 +687,53 @@ static int nand_davinci_probe(struct platform_device *pdev)
 	info->chip.write_buf    = nand_davinci_write_buf;
 
 	/* Use board-specific ECC config */
-	ecc_mode		= pdata->ecc_mode;
+	info->chip.ecc.mode	= pdata->ecc_mode;
 
 	ret = -EINVAL;
-	switch (ecc_mode) {
+
+	info->clk = devm_clk_get(&pdev->dev, "aemif");
+	if (IS_ERR(info->clk)) {
+		ret = PTR_ERR(info->clk);
+		dev_dbg(&pdev->dev, "unable to get AEMIF clock, err %d\n", ret);
+		return ret;
+	}
+
+	ret = clk_prepare_enable(info->clk);
+	if (ret < 0) {
+		dev_dbg(&pdev->dev, "unable to enable AEMIF clock, err %d\n",
+			ret);
+		goto err_clk_enable;
+	}
+
+	spin_lock_irq(&davinci_nand_lock);
+
+	/* put CSxNAND into NAND mode */
+	val = davinci_nand_readl(info, NANDFCR_OFFSET);
+	val |= BIT(info->core_chipsel);
+	davinci_nand_writel(info, NANDFCR_OFFSET, val);
+
+	spin_unlock_irq(&davinci_nand_lock);
+
+	/* Scan to find existence of the device(s) */
+	ret = nand_scan_ident(mtd, pdata->mask_chipsel ? 2 : 1, NULL);
+	if (ret < 0) {
+		dev_dbg(&pdev->dev, "no NAND chip(s) found\n");
+		goto err;
+	}
+
+	switch (info->chip.ecc.mode) {
 	case NAND_ECC_NONE:
+		pdata->ecc_bits = 0;
+		break;
 	case NAND_ECC_SOFT:
 		pdata->ecc_bits = 0;
+		/*
+		 * This driver expects Hamming based ECC when ecc_mode is set
+		 * to NAND_ECC_SOFT. Force ecc.algo to NAND_ECC_HAMMING to
+		 * avoid adding an extra ->ecc_algo field to
+		 * davinci_nand_pdata.
+		 */
+		info->chip.ecc.algo = NAND_ECC_HAMMING;
 		break;
 	case NAND_ECC_HW:
 		if (pdata->ecc_bits == 4) {
@@ -754,37 +769,6 @@ static int nand_davinci_probe(struct platform_device *pdev)
 	default:
 		return -EINVAL;
 	}
-	info->chip.ecc.mode = ecc_mode;
-
-	info->clk = devm_clk_get(&pdev->dev, "aemif");
-	if (IS_ERR(info->clk)) {
-		ret = PTR_ERR(info->clk);
-		dev_dbg(&pdev->dev, "unable to get AEMIF clock, err %d\n", ret);
-		return ret;
-	}
-
-	ret = clk_prepare_enable(info->clk);
-	if (ret < 0) {
-		dev_dbg(&pdev->dev, "unable to enable AEMIF clock, err %d\n",
-			ret);
-		goto err_clk_enable;
-	}
-
-	spin_lock_irq(&davinci_nand_lock);
-
-	/* put CSxNAND into NAND mode */
-	val = davinci_nand_readl(info, NANDFCR_OFFSET);
-	val |= BIT(info->core_chipsel);
-	davinci_nand_writel(info, NANDFCR_OFFSET, val);
-
-	spin_unlock_irq(&davinci_nand_lock);
-
-	/* Scan to find existence of the device(s) */
-	ret = nand_scan_ident(mtd, pdata->mask_chipsel ? 2 : 1, NULL);
-	if (ret < 0) {
-		dev_dbg(&pdev->dev, "no NAND chip(s) found\n");
-		goto err;
-	}
 
 	/* Update ECC layout if needed ... for 1-bit HW ECC, the default
 	 * is OK, but it allocates 6 bytes when only 3 are needed (for
@@ -805,26 +789,14 @@ static int nand_davinci_probe(struct platform_device *pdev)
 		 * table marker fits in the free bytes.
 		 */
 		if (chunks == 1) {
-			info->ecclayout = hwecc4_small;
-			info->ecclayout.oobfree[1].length = mtd->oobsize - 16;
-			goto syndrome_done;
-		}
-		if (chunks == 4) {
-			info->ecclayout = hwecc4_2048;
-			info->chip.ecc.mode = NAND_ECC_HW_OOB_FIRST;
-			goto syndrome_done;
-		}
-		if (chunks == 8) {
-			info->ecclayout = hwecc4_4096;
+			mtd_set_ooblayout(mtd, &hwecc4_small_ooblayout_ops);
+		} else if (chunks == 4 || chunks == 8) {
+			mtd_set_ooblayout(mtd, &nand_ooblayout_lp_ops);
 			info->chip.ecc.mode = NAND_ECC_HW_OOB_FIRST;
-			goto syndrome_done;
+		} else {
+			ret = -EIO;
+			goto err;
 		}
-
-		ret = -EIO;
-		goto err;
-
-syndrome_done:
-		info->chip.ecc.layout = &info->ecclayout;
 	}
 
 	ret = nand_scan_tail(mtd);
@@ -850,7 +822,7 @@ static int nand_davinci_probe(struct platform_device *pdev)
 
 err_clk_enable:
 	spin_lock_irq(&davinci_nand_lock);
-	if (ecc_mode == NAND_ECC_HW_SYNDROME)
+	if (info->chip.ecc.mode == NAND_ECC_HW_SYNDROME)
 		ecc4_busy = false;
 	spin_unlock_irq(&davinci_nand_lock);
 	return ret;

drivers/mtd/nand/denali.c

@@ -1374,13 +1374,41 @@ static void denali_hw_init(struct denali_nand_info *denali)
  * correction
  */
 #define ECC_8BITS	14
-static struct nand_ecclayout nand_8bit_oob = {
-	.eccbytes = 14,
-};
-
 #define ECC_15BITS	26
-static struct nand_ecclayout nand_15bit_oob = {
-	.eccbytes = 26,
+
+static int denali_ooblayout_ecc(struct mtd_info *mtd, int section,
+				struct mtd_oob_region *oobregion)
+{
+	struct denali_nand_info *denali = mtd_to_denali(mtd);
+	struct nand_chip *chip = mtd_to_nand(mtd);
+
+	if (section)
+		return -ERANGE;
+
+	oobregion->offset = denali->bbtskipbytes;
+	oobregion->length = chip->ecc.total;
+
+	return 0;
+}
+
+static int denali_ooblayout_free(struct mtd_info *mtd, int section,
+				 struct mtd_oob_region *oobregion)
+{
+	struct denali_nand_info *denali = mtd_to_denali(mtd);
+	struct nand_chip *chip = mtd_to_nand(mtd);
+
+	if (section)
+		return -ERANGE;
+
+	oobregion->offset = chip->ecc.total + denali->bbtskipbytes;
+	oobregion->length = mtd->oobsize - oobregion->offset;
+
+	return 0;
+}
+
+static const struct mtd_ooblayout_ops denali_ooblayout_ops = {
+	.ecc = denali_ooblayout_ecc,
+	.free = denali_ooblayout_free,
 };
 
 static uint8_t bbt_pattern[] = {'B', 'b', 't', '0' };
@@ -1561,7 +1589,6 @@ int denali_init(struct denali_nand_info *denali)
 			ECC_SECTOR_SIZE)))) {
 		/* if MLC OOB size is large enough, use 15bit ECC*/
 		denali->nand.ecc.strength = 15;
-		denali->nand.ecc.layout = &nand_15bit_oob;
 		denali->nand.ecc.bytes = ECC_15BITS;
 		iowrite32(15, denali->flash_reg + ECC_CORRECTION);
 	} else if (mtd->oobsize < (denali->bbtskipbytes +
@@ -1571,20 +1598,13 @@ int denali_init(struct denali_nand_info *denali)
 		goto failed_req_irq;
 	} else {
 		denali->nand.ecc.strength = 8;
-		denali->nand.ecc.layout = &nand_8bit_oob;
 		denali->nand.ecc.bytes = ECC_8BITS;
 		iowrite32(8, denali->flash_reg + ECC_CORRECTION);
 	}
 
+	mtd_set_ooblayout(mtd, &denali_ooblayout_ops);
 	denali->nand.ecc.bytes *= denali->devnum;
 	denali->nand.ecc.strength *= denali->devnum;
-	denali->nand.ecc.layout->eccbytes *=
-		mtd->writesize / ECC_SECTOR_SIZE;
-	denali->nand.ecc.layout->oobfree[0].offset =
-		denali->bbtskipbytes + denali->nand.ecc.layout->eccbytes;
-	denali->nand.ecc.layout->oobfree[0].length =
-		mtd->oobsize - denali->nand.ecc.layout->eccbytes -
-		denali->bbtskipbytes;
 
 	/*
 	 * Let driver know the total blocks number and how many blocks

drivers/mtd/nand/diskonchip.c

@@ -950,20 +950,50 @@ static int doc200x_correct_data(struct mtd_info *mtd, u_char *dat,
 
 //u_char mydatabuf[528];
 
-/* The strange out-of-order .oobfree list below is a (possibly unneeded)
- * attempt to retain compatibility.  It used to read:
- * 	.oobfree = { {8, 8} }
- * Since that leaves two bytes unusable, it was changed.  But the following
- * scheme might affect existing jffs2 installs by moving the cleanmarker:
- * 	.oobfree = { {6, 10} }
- * jffs2 seems to handle the above gracefully, but the current scheme seems
- * safer.  The only problem with it is that any code that parses oobfree must
- * be able to handle out-of-order segments.
- */
-static struct nand_ecclayout doc200x_oobinfo = {
-	.eccbytes = 6,
-	.eccpos = {0, 1, 2, 3, 4, 5},
-	.oobfree = {{8, 8}, {6, 2}}
+static int doc200x_ooblayout_ecc(struct mtd_info *mtd, int section,
+				 struct mtd_oob_region *oobregion)
+{
+	if (section)
+		return -ERANGE;
+
+	oobregion->offset = 0;
+	oobregion->length = 6;
+
+	return 0;
+}
+
+static int doc200x_ooblayout_free(struct mtd_info *mtd, int section,
+				  struct mtd_oob_region *oobregion)
+{
+	if (section > 1)
+		return -ERANGE;
+
+	/*
+	 * The strange out-of-order free bytes definition is a (possibly
+	 * unneeded) attempt to retain compatibility.  It used to read:
+	 *	.oobfree = { {8, 8} }
+	 * Since that leaves two bytes unusable, it was changed.  But the
+	 * following scheme might affect existing jffs2 installs by moving the
+	 * cleanmarker:
+	 *	.oobfree = { {6, 10} }
+	 * jffs2 seems to handle the above gracefully, but the current scheme
+	 * seems safer. The only problem with it is that any code retrieving
+	 * free bytes position must be able to handle out-of-order segments.
+	 */
+	if (!section) {
+		oobregion->offset = 8;
+		oobregion->length = 8;
+	} else {
+		oobregion->offset = 6;
+		oobregion->length = 2;
+	}
+
+	return 0;
+}
+
+static const struct mtd_ooblayout_ops doc200x_ooblayout_ops = {
+	.ecc = doc200x_ooblayout_ecc,
+	.free = doc200x_ooblayout_free,
 };
 
 /* Find the (I)NFTL Media Header, and optionally also the mirror media header.
@@ -1537,6 +1567,7 @@ static int __init doc_probe(unsigned long physadr)
 	nand->bbt_md		= nand->bbt_td + 1;
 
 	mtd->owner		= THIS_MODULE;
+	mtd_set_ooblayout(mtd, &doc200x_ooblayout_ops);
 
 	nand_set_controller_data(nand, doc);
 	nand->select_chip	= doc200x_select_chip;
@@ -1548,7 +1579,6 @@ static int __init doc_probe(unsigned long physadr)
 	nand->ecc.calculate	= doc200x_calculate_ecc;
 	nand->ecc.correct	= doc200x_correct_data;
 
-	nand->ecc.layout	= &doc200x_oobinfo;
 	nand->ecc.mode		= NAND_ECC_HW_SYNDROME;
 	nand->ecc.size		= 512;
 	nand->ecc.bytes		= 6;

drivers/mtd/nand/docg4.c

@@ -222,10 +222,33 @@ struct docg4_priv {
  * Bytes 8 - 14 are hw-generated ecc covering entire page + oob bytes 0 - 14.
  * Byte 15 (the last) is used by the driver as a "page written" flag.
  */
-static struct nand_ecclayout docg4_oobinfo = {
-	.eccbytes = 9,
-	.eccpos = {7, 8, 9, 10, 11, 12, 13, 14, 15},
-	.oobfree = { {.offset = 2, .length = 5} }
+static int docg4_ooblayout_ecc(struct mtd_info *mtd, int section,
+			       struct mtd_oob_region *oobregion)
+{
+	if (section)
+		return -ERANGE;
+
+	oobregion->offset = 7;
+	oobregion->length = 9;
+
+	return 0;
+}
+
+static int docg4_ooblayout_free(struct mtd_info *mtd, int section,
+				struct mtd_oob_region *oobregion)
+{
+	if (section)
+		return -ERANGE;
+
+	oobregion->offset = 2;
+	oobregion->length = 5;
+
+	return 0;
+}
+
+static const struct mtd_ooblayout_ops docg4_ooblayout_ops = {
+	.ecc = docg4_ooblayout_ecc,
+	.free = docg4_ooblayout_free,
 };
 
 /*
@@ -1209,6 +1232,7 @@ static void __init init_mtd_structs(struct mtd_info *mtd)
 	mtd->writesize = DOCG4_PAGE_SIZE;
 	mtd->erasesize = DOCG4_BLOCK_SIZE;
 	mtd->oobsize = DOCG4_OOB_SIZE;
+	mtd_set_ooblayout(mtd, &docg4_ooblayout_ops);
 	nand->chipsize = DOCG4_CHIP_SIZE;
 	nand->chip_shift = DOCG4_CHIP_SHIFT;
 	nand->bbt_erase_shift = nand->phys_erase_shift = DOCG4_ERASE_SHIFT;
@@ -1217,7 +1241,6 @@ static void __init init_mtd_structs(struct mtd_info *mtd)
 	nand->pagemask = 0x3ffff;
 	nand->badblockpos = NAND_LARGE_BADBLOCK_POS;
 	nand->badblockbits = 8;
-	nand->ecc.layout = &docg4_oobinfo;
 	nand->ecc.mode = NAND_ECC_HW_SYNDROME;
 	nand->ecc.size = DOCG4_PAGE_SIZE;
 	nand->ecc.prepad = 8;

drivers/mtd/nand/fsl_elbc_nand.c

@@ -79,32 +79,53 @@ struct fsl_elbc_fcm_ctrl {
 
 /* These map to the positions used by the FCM hardware ECC generator */
 
-/* Small Page FLASH with FMR[ECCM] = 0 */
-static struct nand_ecclayout fsl_elbc_oob_sp_eccm0 = {
-	.eccbytes = 3,
-	.eccpos = {6, 7, 8},
-	.oobfree = { {0, 5}, {9, 7} },
-};
+static int fsl_elbc_ooblayout_ecc(struct mtd_info *mtd, int section,
+				  struct mtd_oob_region *oobregion)
+{
+	struct nand_chip *chip = mtd_to_nand(mtd);
+	struct fsl_elbc_mtd *priv = nand_get_controller_data(chip);
 
-/* Small Page FLASH with FMR[ECCM] = 1 */
-static struct nand_ecclayout fsl_elbc_oob_sp_eccm1 = {
-	.eccbytes = 3,
-	.eccpos = {8, 9, 10},
-	.oobfree = { {0, 5}, {6, 2}, {11, 5} },
-};
+	if (section >= chip->ecc.steps)
+		return -ERANGE;
 
-/* Large Page FLASH with FMR[ECCM] = 0 */
-static struct nand_ecclayout fsl_elbc_oob_lp_eccm0 = {
-	.eccbytes = 12,
-	.eccpos = {6, 7, 8, 22, 23, 24, 38, 39, 40, 54, 55, 56},
-	.oobfree = { {1, 5}, {9, 13}, {25, 13}, {41, 13}, {57, 7} },
-};
+	oobregion->offset = (16 * section) + 6;
+	if (priv->fmr & FMR_ECCM)
+		oobregion->offset += 2;
 
-/* Large Page FLASH with FMR[ECCM] = 1 */
-static struct nand_ecclayout fsl_elbc_oob_lp_eccm1 = {
-	.eccbytes = 12,
-	.eccpos = {8, 9, 10, 24, 25, 26, 40, 41, 42, 56, 57, 58},
-	.oobfree = { {1, 7}, {11, 13}, {27, 13}, {43, 13}, {59, 5} },
+	oobregion->length = chip->ecc.bytes;
+
+	return 0;
+}
+
+static int fsl_elbc_ooblayout_free(struct mtd_info *mtd, int section,
+				   struct mtd_oob_region *oobregion)
+{
+	struct nand_chip *chip = mtd_to_nand(mtd);
+	struct fsl_elbc_mtd *priv = nand_get_controller_data(chip);
+
+	if (section > chip->ecc.steps)
+		return -ERANGE;
+
+	if (!section) {
+		oobregion->offset = 0;
+		if (mtd->writesize > 512)
+			oobregion->offset++;
+		oobregion->length = (priv->fmr & FMR_ECCM) ? 7 : 5;
+	} else {
+		oobregion->offset = (16 * section) -
+				    ((priv->fmr & FMR_ECCM) ? 5 : 7);
+		if (section < chip->ecc.steps)
+			oobregion->length = 13;
+		else
+			oobregion->length = mtd->oobsize - oobregion->offset;
+	}
+
+	return 0;
+}
+
+static const struct mtd_ooblayout_ops fsl_elbc_ooblayout_ops = {
+	.ecc = fsl_elbc_ooblayout_ecc,
+	.free = fsl_elbc_ooblayout_free,
 };
 
 /*
@@ -657,8 +678,8 @@ static int fsl_elbc_chip_init_tail(struct mtd_info *mtd)
 	        chip->ecc.bytes);
 	dev_dbg(priv->dev, "fsl_elbc_init: nand->ecc.total = %d\n",
 	        chip->ecc.total);
-	dev_dbg(priv->dev, "fsl_elbc_init: nand->ecc.layout = %p\n",
-	        chip->ecc.layout);
+	dev_dbg(priv->dev, "fsl_elbc_init: mtd->ooblayout = %p\n",
+		mtd->ooblayout);
 	dev_dbg(priv->dev, "fsl_elbc_init: mtd->flags = %08x\n", mtd->flags);
 	dev_dbg(priv->dev, "fsl_elbc_init: mtd->size = %lld\n", mtd->size);
 	dev_dbg(priv->dev, "fsl_elbc_init: mtd->erasesize = %d\n",
@@ -675,14 +696,6 @@ static int fsl_elbc_chip_init_tail(struct mtd_info *mtd)
 	} else if (mtd->writesize == 2048) {
 		priv->page_size = 1;
 		setbits32(&lbc->bank[priv->bank].or, OR_FCM_PGS);
-		/* adjust ecc setup if needed */
-		if ((in_be32(&lbc->bank[priv->bank].br) & BR_DECC) ==
-		    BR_DECC_CHK_GEN) {
-			chip->ecc.size = 512;
-			chip->ecc.layout = (priv->fmr & FMR_ECCM) ?
-			                   &fsl_elbc_oob_lp_eccm1 :
-			                   &fsl_elbc_oob_lp_eccm0;
-		}
 	} else {
 		dev_err(priv->dev,
 		        "fsl_elbc_init: page size %d is not supported\n",
@@ -780,15 +793,14 @@ static int fsl_elbc_chip_init(struct fsl_elbc_mtd *priv)
 	if ((in_be32(&lbc->bank[priv->bank].br) & BR_DECC) ==
 	    BR_DECC_CHK_GEN) {
 		chip->ecc.mode = NAND_ECC_HW;
-		/* put in small page settings and adjust later if needed */
-		chip->ecc.layout = (priv->fmr & FMR_ECCM) ?
-				&fsl_elbc_oob_sp_eccm1 : &fsl_elbc_oob_sp_eccm0;
+		mtd_set_ooblayout(mtd, &fsl_elbc_ooblayout_ops);
 		chip->ecc.size = 512;
 		chip->ecc.bytes = 3;
 		chip->ecc.strength = 1;
 	} else {
 		/* otherwise fall back to default software ECC */
 		chip->ecc.mode = NAND_ECC_SOFT;
+		chip->ecc.algo = NAND_ECC_HAMMING;
 	}
 
 	return 0;

drivers/mtd/nand/fsl_upm.c

@@ -170,6 +170,7 @@ static int fun_chip_init(struct fsl_upm_nand *fun,
 	fun->chip.read_buf = fun_read_buf;
 	fun->chip.write_buf = fun_write_buf;
 	fun->chip.ecc.mode = NAND_ECC_SOFT;
+	fun->chip.ecc.algo = NAND_ECC_HAMMING;
 	if (fun->mchip_count > 1)
 		fun->chip.select_chip = fun_select_chip;
 

drivers/mtd/nand/gpio.c

@@ -273,6 +273,7 @@ static int gpio_nand_probe(struct platform_device *pdev)
 	nand_set_flash_node(chip, pdev->dev.of_node);
 	chip->IO_ADDR_W		= chip->IO_ADDR_R;
 	chip->ecc.mode		= NAND_ECC_SOFT;
+	chip->ecc.algo		= NAND_ECC_HAMMING;
 	chip->options		= gpiomtd->plat.options;
 	chip->chip_delay	= gpiomtd->plat.chip_delay;
 	chip->cmd_ctrl		= gpio_nand_cmd_ctrl;

drivers/mtd/nand/gpmi-nand/gpmi-nand.c

@@ -25,7 +25,6 @@
 #include <linux/mtd/partitions.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
-#include <linux/of_mtd.h>
 #include "gpmi-nand.h"
 #include "bch-regs.h"
 
@@ -47,10 +46,44 @@ static struct nand_bbt_descr gpmi_bbt_descr = {
  * We may change the layout if we can get the ECC info from the datasheet,
  * else we will use all the (page + OOB).
  */
-static struct nand_ecclayout gpmi_hw_ecclayout = {
-	.eccbytes = 0,
-	.eccpos = { 0, },
-	.oobfree = { {.offset = 0, .length = 0} }
+static int gpmi_ooblayout_ecc(struct mtd_info *mtd, int section,
+			      struct mtd_oob_region *oobregion)
+{
+	struct nand_chip *chip = mtd_to_nand(mtd);
+	struct gpmi_nand_data *this = nand_get_controller_data(chip);
+	struct bch_geometry *geo = &this->bch_geometry;
+
+	if (section)
+		return -ERANGE;
+
+	oobregion->offset = 0;
+	oobregion->length = geo->page_size - mtd->writesize;
+
+	return 0;
+}
+
+static int gpmi_ooblayout_free(struct mtd_info *mtd, int section,
+			       struct mtd_oob_region *oobregion)
+{
+	struct nand_chip *chip = mtd_to_nand(mtd);
+	struct gpmi_nand_data *this = nand_get_controller_data(chip);
+	struct bch_geometry *geo = &this->bch_geometry;
+
+	if (section)
+		return -ERANGE;
+
+	/* The available oob size we have. */
+	if (geo->page_size < mtd->writesize + mtd->oobsize) {
+		oobregion->offset = geo->page_size - mtd->writesize;
+		oobregion->length = mtd->oobsize - oobregion->offset;
+	}
+
+	return 0;
+}
+
+static const struct mtd_ooblayout_ops gpmi_ooblayout_ops = {
+	.ecc = gpmi_ooblayout_ecc,
+	.free = gpmi_ooblayout_free,
 };
 
 static const struct gpmi_devdata gpmi_devdata_imx23 = {
@@ -141,7 +174,6 @@ static int set_geometry_by_ecc_info(struct gpmi_nand_data *this)
 	struct bch_geometry *geo = &this->bch_geometry;
 	struct nand_chip *chip = &this->nand;
 	struct mtd_info *mtd = nand_to_mtd(chip);
-	struct nand_oobfree *of = gpmi_hw_ecclayout.oobfree;
 	unsigned int block_mark_bit_offset;
 
 	if (!(chip->ecc_strength_ds > 0 && chip->ecc_step_ds > 0))
@@ -229,12 +261,6 @@ static int set_geometry_by_ecc_info(struct gpmi_nand_data *this)
 	geo->page_size = mtd->writesize + geo->metadata_size +
 		(geo->gf_len * geo->ecc_strength * geo->ecc_chunk_count) / 8;
 
-	/* The available oob size we have. */
-	if (geo->page_size < mtd->writesize + mtd->oobsize) {
-		of->offset = geo->page_size - mtd->writesize;
-		of->length = mtd->oobsize - of->offset;
-	}
-
 	geo->payload_size = mtd->writesize;
 
 	geo->auxiliary_status_offset = ALIGN(geo->metadata_size, 4);
@@ -797,6 +823,7 @@ static void gpmi_free_dma_buffer(struct gpmi_nand_data *this)
 
 	this->cmd_buffer	= NULL;
 	this->data_buffer_dma	= NULL;
+	this->raw_buffer	= NULL;
 	this->page_buffer_virt	= NULL;
 	this->page_buffer_size	=  0;
 }
@@ -1037,14 +1064,87 @@ static int gpmi_ecc_read_page(struct mtd_info *mtd, struct nand_chip *chip,
 	/* Loop over status bytes, accumulating ECC status. */
 	status = auxiliary_virt + nfc_geo->auxiliary_status_offset;
 
+	read_page_swap_end(this, buf, nfc_geo->payload_size,
+			   this->payload_virt, this->payload_phys,
+			   nfc_geo->payload_size,
+			   payload_virt, payload_phys);
+
 	for (i = 0; i < nfc_geo->ecc_chunk_count; i++, status++) {
 		if ((*status == STATUS_GOOD) || (*status == STATUS_ERASED))
 			continue;
 
 		if (*status == STATUS_UNCORRECTABLE) {
+			int eccbits = nfc_geo->ecc_strength * nfc_geo->gf_len;
+			u8 *eccbuf = this->raw_buffer;
+			int offset, bitoffset;
+			int eccbytes;
+			int flips;
+
+			/* Read ECC bytes into our internal raw_buffer */
+			offset = nfc_geo->metadata_size * 8;
+			offset += ((8 * nfc_geo->ecc_chunk_size) + eccbits) * (i + 1);
+			offset -= eccbits;
+			bitoffset = offset % 8;
+			eccbytes = DIV_ROUND_UP(offset + eccbits, 8);
+			offset /= 8;
+			eccbytes -= offset;
+			chip->cmdfunc(mtd, NAND_CMD_RNDOUT, offset, -1);
+			chip->read_buf(mtd, eccbuf, eccbytes);
+
+			/*
+			 * ECC data are not byte aligned and we may have
+			 * in-band data in the first and last byte of
+			 * eccbuf. Set non-eccbits to one so that
+			 * nand_check_erased_ecc_chunk() does not count them
+			 * as bitflips.
+			 */
+			if (bitoffset)
+				eccbuf[0] |= GENMASK(bitoffset - 1, 0);
+
+			bitoffset = (bitoffset + eccbits) % 8;
+			if (bitoffset)
+				eccbuf[eccbytes - 1] |= GENMASK(7, bitoffset);
+
+			/*
+			 * The ECC hardware has an uncorrectable ECC status
+			 * code in case we have bitflips in an erased page. As
+			 * nothing was written into this subpage the ECC is
+			 * obviously wrong and we can not trust it. We assume
+			 * at this point that we are reading an erased page and
+			 * try to correct the bitflips in buffer up to
+			 * ecc_strength bitflips. If this is a page with random
+			 * data, we exceed this number of bitflips and have a
+			 * ECC failure. Otherwise we use the corrected buffer.
+			 */
+			if (i == 0) {
+				/* The first block includes metadata */
+				flips = nand_check_erased_ecc_chunk(
+						buf + i * nfc_geo->ecc_chunk_size,
+						nfc_geo->ecc_chunk_size,
+						eccbuf, eccbytes,
+						auxiliary_virt,
+						nfc_geo->metadata_size,
+						nfc_geo->ecc_strength);
+			} else {
+				flips = nand_check_erased_ecc_chunk(
+						buf + i * nfc_geo->ecc_chunk_size,
+						nfc_geo->ecc_chunk_size,
+						eccbuf, eccbytes,
+						NULL, 0,
+						nfc_geo->ecc_strength);
+			}
+
+			if (flips > 0) {
+				max_bitflips = max_t(unsigned int, max_bitflips,
+						     flips);
+				mtd->ecc_stats.corrected += flips;
+				continue;
+			}
+
 			mtd->ecc_stats.failed++;
 			continue;
 		}
+
 		mtd->ecc_stats.corrected += *status;
 		max_bitflips = max_t(unsigned int, max_bitflips, *status);
 	}
@@ -1064,11 +1164,6 @@ static int gpmi_ecc_read_page(struct mtd_info *mtd, struct nand_chip *chip,
 		chip->oob_poi[0] = ((uint8_t *) auxiliary_virt)[0];
 	}
 
-	read_page_swap_end(this, buf, nfc_geo->payload_size,
-			this->payload_virt, this->payload_phys,
-			nfc_geo->payload_size,
-			payload_virt, payload_phys);
-
 	return max_bitflips;
 }
 
@@ -1327,18 +1422,19 @@ static int gpmi_ecc_read_oob(struct mtd_info *mtd, struct nand_chip *chip,
 static int
 gpmi_ecc_write_oob(struct mtd_info *mtd, struct nand_chip *chip, int page)
 {
-	struct nand_oobfree *of = mtd->ecclayout->oobfree;
+	struct mtd_oob_region of = { };
 	int status = 0;
 
 	/* Do we have available oob area? */
-	if (!of->length)
+	mtd_ooblayout_free(mtd, 0, &of);
+	if (!of.length)
 		return -EPERM;
 
 	if (!nand_is_slc(chip))
 		return -EPERM;
 
-	chip->cmdfunc(mtd, NAND_CMD_SEQIN, mtd->writesize + of->offset, page);
-	chip->write_buf(mtd, chip->oob_poi + of->offset, of->length);
+	chip->cmdfunc(mtd, NAND_CMD_SEQIN, mtd->writesize + of.offset, page);
+	chip->write_buf(mtd, chip->oob_poi + of.offset, of.length);
 	chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1);
 
 	status = chip->waitfunc(mtd, chip);
@@ -1840,6 +1936,7 @@ static void gpmi_nand_exit(struct gpmi_nand_data *this)
 static int gpmi_init_last(struct gpmi_nand_data *this)
 {
 	struct nand_chip *chip = &this->nand;
+	struct mtd_info *mtd = nand_to_mtd(chip);
 	struct nand_ecc_ctrl *ecc = &chip->ecc;
 	struct bch_geometry *bch_geo = &this->bch_geometry;
 	int ret;
@@ -1861,7 +1958,7 @@ static int gpmi_init_last(struct gpmi_nand_data *this)
 	ecc->mode	= NAND_ECC_HW;
 	ecc->size	= bch_geo->ecc_chunk_size;
 	ecc->strength	= bch_geo->ecc_strength;
-	ecc->layout	= &gpmi_hw_ecclayout;
+	mtd_set_ooblayout(mtd, &gpmi_ooblayout_ops);
 
 	/*
 	 * We only enable the subpage read when:
@@ -1914,16 +2011,6 @@ static int gpmi_nand_init(struct gpmi_nand_data *this)
 	/* Set up swap_block_mark, must be set before the gpmi_set_geometry() */
 	this->swap_block_mark = !GPMI_IS_MX23(this);
 
-	if (of_get_nand_on_flash_bbt(this->dev->of_node)) {
-		chip->bbt_options |= NAND_BBT_USE_FLASH | NAND_BBT_NO_OOB;
-
-		if (of_property_read_bool(this->dev->of_node,
-						"fsl,no-blockmark-swap"))
-			this->swap_block_mark = false;
-	}
-	dev_dbg(this->dev, "Blockmark swapping %sabled\n",
-		this->swap_block_mark ? "en" : "dis");
-
 	/*
 	 * Allocate a temporary DMA buffer for reading ID in the
 	 * nand_scan_ident().
@@ -1938,6 +2025,16 @@ static int gpmi_nand_init(struct gpmi_nand_data *this)
 	if (ret)
 		goto err_out;
 
+	if (chip->bbt_options & NAND_BBT_USE_FLASH) {
+		chip->bbt_options |= NAND_BBT_NO_OOB;
+
+		if (of_property_read_bool(this->dev->of_node,
+						"fsl,no-blockmark-swap"))
+			this->swap_block_mark = false;
+	}
+	dev_dbg(this->dev, "Blockmark swapping %sabled\n",
+		this->swap_block_mark ? "en" : "dis");
+
 	ret = gpmi_init_last(this);
 	if (ret)
 		goto err_out;