Commit 2d62a33e authored by Scott Teel's avatar Scott Teel Committed by Martin K. Petersen

hpsa: eliminate fake lun0 enclosures

We don't need to create fake enclosure devices at Lun0
in external target array configurations anymore.
This was done to support Pre-SCSI rev 5 controllers
that didn't suppoprt report luns commands, so the
SCSI layer had to scan targets. If there was no
LUN at LUN 0, then the target scan would stop, and
move to the next target.  Lun0 enclosure device
was added to prevent sparsely-numbered LUNs from
being missed.
Reviewed-by: default avatarScott Teel <scott.teel@pmcs.com>
Reviewed-by: default avatarJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: default avatarKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: default avatarMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: default avatarHannes Reinecke <hare@suse.de>
Reviewed-by: default avatarTomas Henzl <thenzl@redhat.com>
Signed-off-by: default avatarDon Brace <don.brace@pmcs.com>
Signed-off-by: default avatarMartin K. Petersen <martin.petersen@oracle.com>
parent 66749d0d
...@@ -3571,60 +3571,6 @@ static void figure_bus_target_lun(struct ctlr_info *h, ...@@ -3571,60 +3571,6 @@ static void figure_bus_target_lun(struct ctlr_info *h,
0, lunid & 0x3fff); 0, lunid & 0x3fff);
} }
/*
* If there is no lun 0 on a target, linux won't find any devices.
* For the external targets (arrays), we have to manually detect the enclosure
* which is at lun zero, as CCISS_REPORT_PHYSICAL_LUNS doesn't report
* it for some reason. *tmpdevice is the target we're adding,
* this_device is a pointer into the current element of currentsd[]
* that we're building up in update_scsi_devices(), below.
* lunzerobits is a bitmap that tracks which targets already have a
* lun 0 assigned.
* Returns 1 if an enclosure was added, 0 if not.
*/
static int add_ext_target_dev(struct ctlr_info *h,
struct hpsa_scsi_dev_t *tmpdevice,
struct hpsa_scsi_dev_t *this_device, u8 *lunaddrbytes,
unsigned long lunzerobits[], int *n_ext_target_devs)
{
unsigned char scsi3addr[8];
if (test_bit(tmpdevice->target, lunzerobits))
return 0; /* There is already a lun 0 on this target. */
if (!is_logical_dev_addr_mode(lunaddrbytes))
return 0; /* It's the logical targets that may lack lun 0. */
if (!tmpdevice->external)
return 0; /* Only external target devices have this problem. */
if (tmpdevice->lun == 0) /* if lun is 0, then we have a lun 0. */
return 0;
memset(scsi3addr, 0, 8);
scsi3addr[3] = tmpdevice->target;
if (is_hba_lunid(scsi3addr))
return 0; /* Don't add the RAID controller here. */
if (is_scsi_rev_5(h))
return 0; /* p1210m doesn't need to do this. */
if (*n_ext_target_devs >= MAX_EXT_TARGETS) {
dev_warn(&h->pdev->dev, "Maximum number of external "
"target devices exceeded. Check your hardware "
"configuration.");
return 0;
}
if (hpsa_update_device_info(h, scsi3addr, this_device, NULL))
return 0;
(*n_ext_target_devs)++;
hpsa_set_bus_target_lun(this_device,
tmpdevice->bus, tmpdevice->target, 0);
hpsa_update_device_supports_aborts(h, this_device, scsi3addr);
set_bit(tmpdevice->target, lunzerobits);
return 1;
}
/* /*
* Get address of physical disk used for an ioaccel2 mode command: * Get address of physical disk used for an ioaccel2 mode command:
...@@ -3952,20 +3898,6 @@ static void hpsa_update_scsi_devices(struct ctlr_info *h) ...@@ -3952,20 +3898,6 @@ static void hpsa_update_scsi_devices(struct ctlr_info *h)
hpsa_update_device_supports_aborts(h, tmpdevice, lunaddrbytes); hpsa_update_device_supports_aborts(h, tmpdevice, lunaddrbytes);
this_device = currentsd[ncurrent]; this_device = currentsd[ncurrent];
/*
* For external target devices, we have to insert a LUN 0 which
* doesn't show up in CCISS_REPORT_PHYSICAL data, but there
* is nonetheless an enclosure device there. We have to
* present that otherwise linux won't find anything if
* there is no lun 0.
*/
if (add_ext_target_dev(h, tmpdevice, this_device,
lunaddrbytes, lunzerobits,
&n_ext_target_devs)) {
ncurrent++;
this_device = currentsd[ncurrent];
}
*this_device = *tmpdevice; *this_device = *tmpdevice;
this_device->physical_device = physical_device; this_device->physical_device = physical_device;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment