Merge tag 'v3.19-rockchip-dts2' of...

Merge tag 'v3.19-rockchip-dts2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt

Pull "ARM: rockchip: second batch of dts related changes" from Heiko Stuebner:

- the dts part of the rk3288 smp support
- rate init for rk3288 clocks
- enablement of various peripherals
- new boardfile for Haoyu Marsboard (rk3066 based)

* tag 'v3.19-rockchip-dts2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  ARM: dts: rockchip: enable PWM on Radxa Rock
  ARM: dts: rockchip: fix invalid unit-address in rk3188.dtsi
  ARM: dts: rk3288: add VOP iommu nodes
  ARM: dts: rockchip: add reset for CPU nodes
  ARM: dts: rockchip: add intmem node for rk3288 smp support
  ARM: dts: rockchip: add pmu references to cpus nodes
  ARM: dts: rockchip: add serial aliases for rk3066 and rk3188
  ARM: dts: rockchip: Add devicetree source for MarsBoard RK3066
  ARM: dts: rockchip: Add EMAC Rockchip for RK3066 SoCs
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Documentation/devicetree/bindings/arm/rockchip.txt

 Rockchip platforms device tree bindings
 ---------------------------------------
 
+- MarsBoard RK3066 board:
+    Required root node properties:
+      - compatible = "haoyu,marsboard-rk3066", "rockchip,rk3066a";
+
 - bq Curie 2 tablet:
     Required root node properties:
       - compatible = "mundoreader,bq-curie2", "rockchip,rk3066a";

arch/arm/boot/dts/Makefile

@@ -376,6 +376,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
 dtb-$(CONFIG_ARCH_REALVIEW) += arm-realview-pb1176.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += \
 	rk3066a-bqcurie2.dtb \
+	rk3066a-marsboard.dtb \
 	rk3188-radxarock.dtb \
 	rk3288-evb-act8846.dtb \
 	rk3288-evb-rk808.dtb

arch/arm/boot/dts/rk3066a-marsboard.dts

+/*
+ * Copyright (c) 2014 Romain Perier <romain.perier@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "rk3066a.dtsi"
+
+/ {
+	model = "MarsBoard RK3066";
+	compatible = "haoyu,marsboard-rk3066", "rockchip,rk3066a";
+
+	memory {
+		reg = <0x60000000 0x40000000>;
+	};
+
+	vcc_sd0: sdmmc-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "sdmmc-supply";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		gpio = <&gpio3 7 GPIO_ACTIVE_LOW>;
+		startup-delay-us = <100000>;
+		vin-supply = <&vcc_io>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	tps: tps@2d {
+		reg = <0x2d>;
+
+		interrupt-parent = <&gpio6>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+
+		vcc5-supply = <&vcc_io>;
+		vcc6-supply = <&vcc_io>;
+
+		regulators {
+			vcc_rtc: regulator@0 {
+				regulator-name = "vcc_rtc";
+				regulator-always-on;
+			};
+
+			vcc_io: regulator@1 {
+				regulator-name = "vcc_io";
+				regulator-always-on;
+			};
+
+			vdd_arm: regulator@2 {
+				regulator-name = "vdd_arm";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vcc_ddr: regulator@3 {
+				regulator-name = "vcc_ddr";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vcc18_cif: regulator@5 {
+				regulator-name = "vcc18_cif";
+				regulator-always-on;
+			};
+
+			vdd_11: regulator@6 {
+				regulator-name = "vdd_11";
+				regulator-always-on;
+			};
+
+			vcc_25: regulator@7 {
+				regulator-name = "vcc_25";
+				regulator-always-on;
+			};
+
+			vcc_18: regulator@8 {
+				regulator-name = "vcc_18";
+				regulator-always-on;
+			};
+
+			vcc25_hdmi: regulator@9 {
+				regulator-name = "vcc25_hdmi";
+				regulator-always-on;
+			};
+
+			vcca_33: regulator@10 {
+				regulator-name = "vcca_33";
+				regulator-always-on;
+			};
+
+			vcc_rmii: regulator@11 {
+				regulator-name = "vcc_rmii";
+			};
+
+			vcc28_cif: regulator@12 {
+				regulator-name = "vcc28_cif";
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+/* must be included after &tps gets defined */
+#include "tps65910.dtsi"
+
+&emac {
+	status = "okay";
+
+	phy = <&phy0>;
+	phy-supply = <&vcc_rmii>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&phy_int>;
+
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&pinctrl {
+	lan8720a {
+		phy_int: phy-int {
+			rockchip,pins = <RK_GPIO1 26 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&wdt {
+	status = "okay";
+};

arch/arm/boot/dts/rk3066a.dtsi

@@ -234,6 +234,24 @@ pcfg_pull_none: pcfg_pull_none {
 			bias-disable;
 		};
 
+		emac {
+			emac_xfer: emac-xfer {
+				rockchip,pins = <RK_GPIO1 16 RK_FUNC_2 &pcfg_pull_none>, /* mac_clk */
+						<RK_GPIO1 17 RK_FUNC_2 &pcfg_pull_none>, /* tx_en */
+						<RK_GPIO1 18 RK_FUNC_2 &pcfg_pull_none>, /* txd1 */
+						<RK_GPIO1 19 RK_FUNC_2 &pcfg_pull_none>, /* txd0 */
+						<RK_GPIO1 20 RK_FUNC_2 &pcfg_pull_none>, /* rx_err */
+						<RK_GPIO1 21 RK_FUNC_2 &pcfg_pull_none>, /* crs_dvalid */
+						<RK_GPIO1 22 RK_FUNC_2 &pcfg_pull_none>, /* rxd1 */
+						<RK_GPIO1 23 RK_FUNC_2 &pcfg_pull_none>; /* rxd0 */
+			};
+
+			emac_mdio: emac-mdio {
+				rockchip,pins = <RK_GPIO1 24 RK_FUNC_2 &pcfg_pull_none>, /* mac_md */
+						<RK_GPIO1 25 RK_FUNC_2 &pcfg_pull_none>; /* mac_mdclk */
+			};
+		};
+
 		emmc {
 			emmc_clk: emmc-clk {
 				rockchip,pins = <RK_GPIO3 31 RK_FUNC_2 &pcfg_pull_default>;
@@ -587,3 +605,7 @@ &uart3 {
 &wdt {
 	compatible = "rockchip,rk3066-wdt", "snps,dw-wdt";
 };
+
+&emac {
+	compatible = "rockchip,rk3066-emac";
+};

arch/arm/boot/dts/rk3188-radxarock.dts

@@ -243,6 +243,18 @@ &mmc0 {
 	disable-wp;
 };
 
+&pwm1 {
+	status = "okay";
+};
+
+&pwm2 {
+	status = "okay";
+};
+
+&pwm3 {
+	status = "okay";
+};
+
 &pinctrl {
 	pcfg_output_low: pcfg-output-low {
 		output-low;

arch/arm/boot/dts/rk3188.dtsi

@@ -111,7 +111,7 @@ pinctrl: pinctrl {
 		#size-cells = <1>;
 		ranges;
 
-		gpio0: gpio0@0x2000a000 {
+		gpio0: gpio0@2000a000 {
 			compatible = "rockchip,rk3188-gpio-bank0";
 			reg = <0x2000a000 0x100>;
 			interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
@@ -124,7 +124,7 @@ gpio0: gpio0@0x2000a000 {
 			#interrupt-cells = <2>;
 		};
 
-		gpio1: gpio1@0x2003c000 {
+		gpio1: gpio1@2003c000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x2003c000 0x100>;
 			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/boot/dts/rk3288.dtsi

@@ -46,11 +46,14 @@ aliases {
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
+		enable-method = "rockchip,rk3066-smp";
+		rockchip,pmu = <&pmu>;
 
 		cpu0: cpu@500 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a12";
 			reg = <0x500>;
+			resets = <&cru SRST_CORE0>;
 			operating-points = <
 				/* KHz    uV */
 				1608000 1350000
@@ -73,16 +76,19 @@ cpu@501 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a12";
 			reg = <0x501>;
+			resets = <&cru SRST_CORE1>;
 		};
 		cpu@502 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a12";
 			reg = <0x502>;
+			resets = <&cru SRST_CORE2>;
 		};
 		cpu@503 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a12";
 			reg = <0x503>;
+			resets = <&cru SRST_CORE3>;
 		};
 	};
 
@@ -462,6 +468,18 @@ pwm3: pwm@ff680030 {
 		status = "disabled";
 	};
 
+	bus_intmem@ff700000 {
+		compatible = "mmio-sram";
+		reg = <0xff700000 0x18000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xff700000 0x18000>;
+		smp-sram@0 {
+			compatible = "rockchip,rk3066-smp-sram";
+			reg = <0x00 0x10>;
+		};
+	};
+
 	pmu: power-management@ff730000 {
 		compatible = "rockchip,rk3288-pmu", "syscon";
 		reg = <0xff730000 0x100>;
@@ -517,6 +535,24 @@ i2s: i2s@ff890000 {
 		status = "disabled";
 	};
 
+	vopb_mmu: iommu@ff930300 {
+		compatible = "rockchip,iommu";
+		reg = <0xff930300 0x100>;
+		interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "vopb_mmu";
+		#iommu-cells = <0>;
+		status = "disabled";
+	};
+
+	vopl_mmu: iommu@ff940300 {
+		compatible = "rockchip,iommu";
+		reg = <0xff940300 0x100>;
+		interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "vopl_mmu";
+		#iommu-cells = <0>;
+		status = "disabled";
+	};
+
 	gic: interrupt-controller@ffc01000 {
 		compatible = "arm,gic-400";
 		interrupt-controller;

arch/arm/boot/dts/rk3xxx.dtsi

@@ -29,6 +29,10 @@ aliases {
 		mshc0 = &emmc;
 		mshc1 = &mmc0;
 		mshc2 = &mmc1;
+		serial0 = &uart0;
+		serial1 = &uart1;
+		serial2 = &uart2;
+		serial3 = &uart3;
 		spi0 = &spi0;
 		spi1 = &spi1;
 	};