Commit 2f7f4efb authored by Randy Dunlap's avatar Randy Dunlap Committed by Benjamin Tissoires

Documentation: hid: correct spelling

Correct spelling problems for Documentation/hid/ as reported
by codespell.
Signed-off-by: default avatarRandy Dunlap <rdunlap@infradead.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: linux-input@vger.kernel.org
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Acked-by: default avatarSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20230127064005.1558-11-rdunlap@infradead.orgSigned-off-by: default avatarBenjamin Tissoires <benjamin.tissoires@redhat.com>
parent 0c2d5728
......@@ -9,7 +9,7 @@ Currently ALPS HID driver supports U1 Touchpad device.
U1 device basic information.
========== ======
Vender ID 0x044E
Vendor ID 0x044E
Product ID 0x120B
Version ID 0x0121
========== ======
......
......@@ -307,7 +307,7 @@ sysfs path: ``/sys/bus/hid/devices/xxxx:yyyy:zzzz:0000``)
We can not rely on hidraw to bind a BPF program to a HID device. hidraw is an
artefact of the processing of the HID device, and is not stable. Some drivers
even disable it, so that removes the tracing capabilies on those devices
even disable it, so that removes the tracing capabilities on those devices
(where it is interesting to get the non-hidraw traces).
On the other hand, the ``hid_id`` is stable for the entire life of the HID device,
......
......@@ -8,7 +8,7 @@ Introduction
In addition to the normal input type HID devices, USB also uses the
human interface device protocols for things that are not really human
interfaces, but have similar sorts of communication needs. The two big
examples for this are power devices (especially uninterruptable power
examples for this are power devices (especially uninterruptible power
supplies) and monitor control on higher end monitors.
To support these disparate requirements, the Linux USB system provides
......
......@@ -163,7 +163,7 @@ HIDIOCGOUTPUT(len):
Get an Output Report
This ioctl will request an output report from the device using the control
endpoint. Typically, this is used to retrive the initial state of
endpoint. Typically, this is used to retrieve the initial state of
an output report of a device, before an application updates it as necessary either
via a HIDIOCSOUTPUT request, or the regular device write() interface. The format
of the buffer issued with this report is identical to that of HIDIOCGFEATURE.
......
......@@ -199,7 +199,7 @@ the sender that the memory region for that message may be reused.
DMA initialization is started with host sending DMA_ALLOC_NOTIFY bus message
(that includes RX buffer) and FW responds with DMA_ALLOC_NOTIFY_ACK.
Additionally to DMA address communication, this sequence checks capabilities:
if thw host doesn't support DMA, then it won't send DMA allocation, so FW can't
if the host doesn't support DMA, then it won't send DMA allocation, so FW can't
send DMA; if FW doesn't support DMA then it won't respond with
DMA_ALLOC_NOTIFY_ACK, in which case host will not use DMA transfers.
Here ISH acts as busmaster DMA controller. Hence when host sends DMA_XFER,
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment