igb: Add support for DH89xxCC

This patch adds support for the Intel(r) DH89xxCC series. The new
device will be using Intel(r) i347-AT4 and Marvell(r) M88E1322 and
M88E1112 PHYs. Support for these devices has also been added here.
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/igb/e1000_82575.c

@@ -132,6 +132,8 @@ static s32 igb_get_invariants_82575(struct e1000_hw *hw)
 	case E1000_DEV_ID_82580_SERDES:
 	case E1000_DEV_ID_82580_SGMII:
 	case E1000_DEV_ID_82580_COPPER_DUAL:
+	case E1000_DEV_ID_DH89XXCC_SGMII:
+	case E1000_DEV_ID_DH89XXCC_SERDES:
 		mac->type = e1000_82580;
 		break;
 	case E1000_DEV_ID_I350_COPPER:
@@ -282,10 +284,18 @@ static s32 igb_get_invariants_82575(struct e1000_hw *hw)
 
 	/* Verify phy id and set remaining function pointers */
 	switch (phy->id) {
+	case I347AT4_E_PHY_ID:
+	case M88E1112_E_PHY_ID:
 	case M88E1111_I_PHY_ID:
 		phy->type                   = e1000_phy_m88;
 		phy->ops.get_phy_info       = igb_get_phy_info_m88;
-		phy->ops.get_cable_length   = igb_get_cable_length_m88;
+
+		if (phy->id == I347AT4_E_PHY_ID ||
+		    phy->id == M88E1112_E_PHY_ID)
+			phy->ops.get_cable_length = igb_get_cable_length_m88_gen2;
+		else
+			phy->ops.get_cable_length = igb_get_cable_length_m88;
+
 		phy->ops.force_speed_duplex = igb_phy_force_speed_duplex_m88;
 		break;
 	case IGP03E1000_E_PHY_ID:
@@ -1058,7 +1068,11 @@ static s32 igb_setup_copper_link_82575(struct e1000_hw *hw)
 	}
 	switch (hw->phy.type) {
 	case e1000_phy_m88:
-		ret_val = igb_copper_link_setup_m88(hw);
+		if (hw->phy.id == I347AT4_E_PHY_ID ||
+		    hw->phy.id == M88E1112_E_PHY_ID)
+			ret_val = igb_copper_link_setup_m88_gen2(hw);
+		else
+			ret_val = igb_copper_link_setup_m88(hw);
 		break;
 	case e1000_phy_igp_3:
 		ret_val = igb_copper_link_setup_igp(hw);

drivers/net/igb/e1000_defines.h

@@ -634,6 +634,8 @@
  * E = External
  */
 #define M88E1111_I_PHY_ID    0x01410CC0
+#define M88E1112_E_PHY_ID    0x01410C90
+#define I347AT4_E_PHY_ID     0x01410DC0
 #define IGP03E1000_E_PHY_ID  0x02A80390
 #define I82580_I_PHY_ID      0x015403A0
 #define I350_I_PHY_ID        0x015403B0
@@ -702,6 +704,35 @@
 #define M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X    0x0100
 #define M88E1000_EPSCR_TX_CLK_25      0x0070 /* 25  MHz TX_CLK */
 
+/* Intel i347-AT4 Registers */
+
+#define I347AT4_PCDL                   0x10 /* PHY Cable Diagnostics Length */
+#define I347AT4_PCDC                   0x15 /* PHY Cable Diagnostics Control */
+#define I347AT4_PAGE_SELECT            0x16
+
+/* i347-AT4 Extended PHY Specific Control Register */
+
+/*
+ *  Number of times we will attempt to autonegotiate before downshifting if we
+ *  are the master
+ */
+#define I347AT4_PSCR_DOWNSHIFT_ENABLE 0x0800
+#define I347AT4_PSCR_DOWNSHIFT_MASK   0x7000
+#define I347AT4_PSCR_DOWNSHIFT_1X     0x0000
+#define I347AT4_PSCR_DOWNSHIFT_2X     0x1000
+#define I347AT4_PSCR_DOWNSHIFT_3X     0x2000
+#define I347AT4_PSCR_DOWNSHIFT_4X     0x3000
+#define I347AT4_PSCR_DOWNSHIFT_5X     0x4000
+#define I347AT4_PSCR_DOWNSHIFT_6X     0x5000
+#define I347AT4_PSCR_DOWNSHIFT_7X     0x6000
+#define I347AT4_PSCR_DOWNSHIFT_8X     0x7000
+
+/* i347-AT4 PHY Cable Diagnostics Control */
+#define I347AT4_PCDC_CABLE_LENGTH_UNIT 0x0400 /* 0=cm 1=meters */
+
+/* Marvell 1112 only registers */
+#define M88E1112_VCT_DSP_DISTANCE       0x001A
+
 /* M88EC018 Rev 2 specific DownShift settings */
 #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK  0x0E00
 #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X    0x0800

drivers/net/igb/e1000_hw.h

@@ -54,6 +54,8 @@ struct e1000_hw;
 #define E1000_DEV_ID_82580_SERDES             0x1510
 #define E1000_DEV_ID_82580_SGMII              0x1511
 #define E1000_DEV_ID_82580_COPPER_DUAL        0x1516
+#define E1000_DEV_ID_DH89XXCC_SGMII           0x0436
+#define E1000_DEV_ID_DH89XXCC_SERDES          0x0438
 #define E1000_DEV_ID_I350_COPPER              0x1521
 #define E1000_DEV_ID_I350_FIBER               0x1522
 #define E1000_DEV_ID_I350_SERDES              0x1523

drivers/net/igb/e1000_phy.c

@@ -569,6 +569,89 @@ s32 igb_copper_link_setup_m88(struct e1000_hw *hw)
 	return ret_val;
 }
 
+/**
+ *  igb_copper_link_setup_m88_gen2 - Setup m88 PHY's for copper link
+ *  @hw: pointer to the HW structure
+ *
+ *  Sets up MDI/MDI-X and polarity for i347-AT4, m88e1322 and m88e1112 PHY's.
+ *  Also enables and sets the downshift parameters.
+ **/
+s32 igb_copper_link_setup_m88_gen2(struct e1000_hw *hw)
+{
+	struct e1000_phy_info *phy = &hw->phy;
+	s32 ret_val;
+	u16 phy_data;
+
+	if (phy->reset_disable) {
+		ret_val = 0;
+		goto out;
+	}
+
+	/* Enable CRS on Tx. This must be set for half-duplex operation. */
+	ret_val = phy->ops.read_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+	if (ret_val)
+		goto out;
+
+	/*
+	 * Options:
+	 *   MDI/MDI-X = 0 (default)
+	 *   0 - Auto for all speeds
+	 *   1 - MDI mode
+	 *   2 - MDI-X mode
+	 *   3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
+	 */
+	phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;
+
+	switch (phy->mdix) {
+	case 1:
+		phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE;
+		break;
+	case 2:
+		phy_data |= M88E1000_PSCR_MDIX_MANUAL_MODE;
+		break;
+	case 3:
+		/* M88E1112 does not support this mode) */
+		if (phy->id != M88E1112_E_PHY_ID) {
+			phy_data |= M88E1000_PSCR_AUTO_X_1000T;
+			break;
+		}
+	case 0:
+	default:
+		phy_data |= M88E1000_PSCR_AUTO_X_MODE;
+		break;
+	}
+
+	/*
+	 * Options:
+	 *   disable_polarity_correction = 0 (default)
+	 *       Automatic Correction for Reversed Cable Polarity
+	 *   0 - Disabled
+	 *   1 - Enabled
+	 */
+	phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL;
+	if (phy->disable_polarity_correction == 1)
+		phy_data |= M88E1000_PSCR_POLARITY_REVERSAL;
+
+	/* Enable downshift and setting it to X6 */
+	phy_data &= ~I347AT4_PSCR_DOWNSHIFT_MASK;
+	phy_data |= I347AT4_PSCR_DOWNSHIFT_6X;
+	phy_data |= I347AT4_PSCR_DOWNSHIFT_ENABLE;
+
+	ret_val = phy->ops.write_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+	if (ret_val)
+		goto out;
+
+	/* Commit the changes. */
+	ret_val = igb_phy_sw_reset(hw);
+	if (ret_val) {
+		hw_dbg("Error committing the PHY changes\n");
+		goto out;
+	}
+
+out:
+	return ret_val;
+}
+
 /**
  *  igb_copper_link_setup_igp - Setup igp PHY's for copper link
  *  @hw: pointer to the HW structure
@@ -1124,18 +1207,25 @@ s32 igb_phy_force_speed_duplex_m88(struct e1000_hw *hw)
 			goto out;
 
 		if (!link) {
-			/*
-			 * We didn't get link.
-			 * Reset the DSP and cross our fingers.
-			 */
-			ret_val = phy->ops.write_reg(hw,
-						     M88E1000_PHY_PAGE_SELECT,
-						     0x001d);
-			if (ret_val)
-				goto out;
-			ret_val = igb_phy_reset_dsp(hw);
-			if (ret_val)
-				goto out;
+			if (hw->phy.type != e1000_phy_m88 ||
+			    hw->phy.id == I347AT4_E_PHY_ID ||
+			    hw->phy.id == M88E1112_E_PHY_ID) {
+				hw_dbg("Link taking longer than expected.\n");
+			} else {
+
+				/*
+				 * We didn't get link.
+				 * Reset the DSP and cross our fingers.
+				 */
+				ret_val = phy->ops.write_reg(hw,
+							     M88E1000_PHY_PAGE_SELECT,
+							     0x001d);
+				if (ret_val)
+					goto out;
+				ret_val = igb_phy_reset_dsp(hw);
+				if (ret_val)
+					goto out;
+			}
 		}
 
 		/* Try once more */
@@ -1145,6 +1235,11 @@ s32 igb_phy_force_speed_duplex_m88(struct e1000_hw *hw)
 			goto out;
 	}
 
+	if (hw->phy.type != e1000_phy_m88 ||
+	    hw->phy.id == I347AT4_E_PHY_ID ||
+	    hw->phy.id == M88E1112_E_PHY_ID)
+		goto out;
+
 	ret_val = phy->ops.read_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data);
 	if (ret_val)
 		goto out;
@@ -1557,6 +1652,93 @@ s32 igb_get_cable_length_m88(struct e1000_hw *hw)
 	return ret_val;
 }
 
+s32 igb_get_cable_length_m88_gen2(struct e1000_hw *hw)
+{
+	struct e1000_phy_info *phy = &hw->phy;
+	s32 ret_val;
+	u16 phy_data, phy_data2, index, default_page, is_cm;
+
+	switch (hw->phy.id) {
+	case I347AT4_E_PHY_ID:
+		/* Remember the original page select and set it to 7 */
+		ret_val = phy->ops.read_reg(hw, I347AT4_PAGE_SELECT,
+					    &default_page);
+		if (ret_val)
+			goto out;
+
+		ret_val = phy->ops.write_reg(hw, I347AT4_PAGE_SELECT, 0x07);
+		if (ret_val)
+			goto out;
+
+		/* Get cable length from PHY Cable Diagnostics Control Reg */
+		ret_val = phy->ops.read_reg(hw, (I347AT4_PCDL + phy->addr),
+					    &phy_data);
+		if (ret_val)
+			goto out;
+
+		/* Check if the unit of cable length is meters or cm */
+		ret_val = phy->ops.read_reg(hw, I347AT4_PCDC, &phy_data2);
+		if (ret_val)
+			goto out;
+
+		is_cm = !(phy_data & I347AT4_PCDC_CABLE_LENGTH_UNIT);
+
+		/* Populate the phy structure with cable length in meters */
+		phy->min_cable_length = phy_data / (is_cm ? 100 : 1);
+		phy->max_cable_length = phy_data / (is_cm ? 100 : 1);
+		phy->cable_length = phy_data / (is_cm ? 100 : 1);
+
+		/* Reset the page selec to its original value */
+		ret_val = phy->ops.write_reg(hw, I347AT4_PAGE_SELECT,
+					     default_page);
+		if (ret_val)
+			goto out;
+		break;
+	case M88E1112_E_PHY_ID:
+		/* Remember the original page select and set it to 5 */
+		ret_val = phy->ops.read_reg(hw, I347AT4_PAGE_SELECT,
+					    &default_page);
+		if (ret_val)
+			goto out;
+
+		ret_val = phy->ops.write_reg(hw, I347AT4_PAGE_SELECT, 0x05);
+		if (ret_val)
+			goto out;
+
+		ret_val = phy->ops.read_reg(hw, M88E1112_VCT_DSP_DISTANCE,
+					    &phy_data);
+		if (ret_val)
+			goto out;
+
+		index = (phy_data & M88E1000_PSSR_CABLE_LENGTH) >>
+			M88E1000_PSSR_CABLE_LENGTH_SHIFT;
+		if (index >= M88E1000_CABLE_LENGTH_TABLE_SIZE - 1) {
+			ret_val = -E1000_ERR_PHY;
+			goto out;
+		}
+
+		phy->min_cable_length = e1000_m88_cable_length_table[index];
+		phy->max_cable_length = e1000_m88_cable_length_table[index + 1];
+
+		phy->cable_length = (phy->min_cable_length +
+				     phy->max_cable_length) / 2;
+
+		/* Reset the page select to its original value */
+		ret_val = phy->ops.write_reg(hw, I347AT4_PAGE_SELECT,
+					     default_page);
+		if (ret_val)
+			goto out;
+
+		break;
+	default:
+		ret_val = -E1000_ERR_PHY;
+		goto out;
+	}
+
+out:
+	return ret_val;
+}
+
 /**
  *  igb_get_cable_length_igp_2 - Determine cable length for igp2 PHY
  *  @hw: pointer to the HW structure

drivers/net/igb/e1000_phy.h

@@ -45,9 +45,11 @@ s32  igb_check_downshift(struct e1000_hw *hw);
 s32  igb_check_reset_block(struct e1000_hw *hw);
 s32  igb_copper_link_setup_igp(struct e1000_hw *hw);
 s32  igb_copper_link_setup_m88(struct e1000_hw *hw);
+s32  igb_copper_link_setup_m88_gen2(struct e1000_hw *hw);
 s32  igb_phy_force_speed_duplex_igp(struct e1000_hw *hw);
 s32  igb_phy_force_speed_duplex_m88(struct e1000_hw *hw);
 s32  igb_get_cable_length_m88(struct e1000_hw *hw);
+s32  igb_get_cable_length_m88_gen2(struct e1000_hw *hw);
 s32  igb_get_cable_length_igp_2(struct e1000_hw *hw);
 s32  igb_get_phy_id(struct e1000_hw *hw);
 s32  igb_get_phy_info_igp(struct e1000_hw *hw);

drivers/net/igb/igb_main.c

@@ -71,6 +71,8 @@ static DEFINE_PCI_DEVICE_TABLE(igb_pci_tbl) = {
 	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_82580_SERDES), board_82575 },
 	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_82580_SGMII), board_82575 },
 	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_82580_COPPER_DUAL), board_82575 },
+	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_DH89XXCC_SGMII), board_82575 },
+	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_DH89XXCC_SERDES), board_82575 },
 	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_82576), board_82575 },
 	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_82576_NS), board_82575 },
 	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_82576_NS_SERDES), board_82575 },