Merge branch 'fixes-for-3.9' of git://gitorious.org/linux-can/linux-can

Marc Kleine-Budde says:

====================
here's a patch series for net for the v3.9 release cycle. Fengguang Wu found
two problems with the sja1000 drivers:

A macro in the SH architecture collides with one in the sja1000 driver. I
created a minimal patch suited for stable, only changing this particular
define. (Once net is merged back to net-next, I'll post a patch to uniformly
use a SJA1000_ prefix for the sja100 private defines.) If you prefer, I can
squash both patches together.

Fengguang further noticed that the peak pcmcia driver will not compile on archs
without ioport support. I created a patch to limit the driver to archs which
select HAS_IOPORT in Kconfig.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/can/sja1000/Kconfig

@@ -46,6 +46,7 @@ config CAN_EMS_PCI
 config CAN_PEAK_PCMCIA
 	tristate "PEAK PCAN-PC Card"
 	depends on PCMCIA
+	depends on HAS_IOPORT
 	---help---
 	  This driver is for the PCAN-PC Card PCMCIA adapter (1 or 2 channels)
 	  from PEAK-System (http://www.peak-system.com). To compile this

drivers/net/can/sja1000/plx_pci.c

@@ -348,7 +348,7 @@ static inline int plx_pci_check_sja1000(const struct sja1000_priv *priv)
 	 */
 	if ((priv->read_reg(priv, REG_CR) & REG_CR_BASICCAN_INITIAL_MASK) ==
 	    REG_CR_BASICCAN_INITIAL &&
-	    (priv->read_reg(priv, REG_SR) == REG_SR_BASICCAN_INITIAL) &&
+	    (priv->read_reg(priv, SJA1000_REG_SR) == REG_SR_BASICCAN_INITIAL) &&
 	    (priv->read_reg(priv, REG_IR) == REG_IR_BASICCAN_INITIAL))
 		flag = 1;
 
@@ -360,7 +360,7 @@ static inline int plx_pci_check_sja1000(const struct sja1000_priv *priv)
 	 * See states on p. 23 of the Datasheet.
 	 */
 	if (priv->read_reg(priv, REG_MOD) == REG_MOD_PELICAN_INITIAL &&
-	    priv->read_reg(priv, REG_SR) == REG_SR_PELICAN_INITIAL &&
+	    priv->read_reg(priv, SJA1000_REG_SR) == REG_SR_PELICAN_INITIAL &&
 	    priv->read_reg(priv, REG_IR) == REG_IR_PELICAN_INITIAL)
 		return flag;
 

drivers/net/can/sja1000/sja1000.c

@@ -92,7 +92,7 @@ static void sja1000_write_cmdreg(struct sja1000_priv *priv, u8 val)
 	 */
 	spin_lock_irqsave(&priv->cmdreg_lock, flags);
 	priv->write_reg(priv, REG_CMR, val);
-	priv->read_reg(priv, REG_SR);
+	priv->read_reg(priv, SJA1000_REG_SR);
 	spin_unlock_irqrestore(&priv->cmdreg_lock, flags);
 }
 
@@ -502,7 +502,7 @@ irqreturn_t sja1000_interrupt(int irq, void *dev_id)
 
 	while ((isrc = priv->read_reg(priv, REG_IR)) && (n < SJA1000_MAX_IRQ)) {
 		n++;
-		status = priv->read_reg(priv, REG_SR);
+		status = priv->read_reg(priv, SJA1000_REG_SR);
 		/* check for absent controller due to hw unplug */
 		if (status == 0xFF && sja1000_is_absent(priv))
 			return IRQ_NONE;
@@ -530,7 +530,7 @@ irqreturn_t sja1000_interrupt(int irq, void *dev_id)
 			/* receive interrupt */
 			while (status & SR_RBS) {
 				sja1000_rx(dev);
-				status = priv->read_reg(priv, REG_SR);
+				status = priv->read_reg(priv, SJA1000_REG_SR);
 				/* check for absent controller */
 				if (status == 0xFF && sja1000_is_absent(priv))
 					return IRQ_NONE;

drivers/net/can/sja1000/sja1000.h

@@ -56,7 +56,7 @@
 /* SJA1000 registers - manual section 6.4 (Pelican Mode) */
 #define REG_MOD		0x00
 #define REG_CMR		0x01
-#define REG_SR		0x02
+#define SJA1000_REG_SR		0x02
 #define REG_IR		0x03
 #define REG_IER		0x04
 #define REG_ALC		0x0B