Merge branch 'omap/dt' into next/late

As pointed out by Stephen Rothwell, commit e5211763 ("ARM: dts:
omap3: Add DT entries for OMAP 3 ISP") conflicts with b8845074
("ARM: dts: omap3: add minimal l4 bus layout with control module support")
in non-obvious ways, causing a build failure when both patches
are present.

This merges the two branches that introduce the respective changes
into the next/late branch to resolve the way that Stephen suggested,
as confirmed by Tony.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lkml.org/lkml/2015/4/6/436Acked-by: Tony Lindgren <tony@atomide.com>

Documentation/devicetree/bindings/media/ti,omap3isp.txt

+OMAP 3 ISP Device Tree bindings
+===============================
+
+The DT definitions can be found in include/dt-bindings/media/omap3-isp.h.
+
+Required properties
+===================
+
+compatible	: must contain "ti,omap3-isp"
+
+reg		: the two registers sets (physical address and length) for the
+		  ISP. The first set contains the core ISP registers up to
+		  the end of the SBL block. The second set contains the
+		  CSI PHYs and receivers registers.
+interrupts	: the ISP interrupt specifier
+iommus		: phandle and IOMMU specifier for the IOMMU that serves the ISP
+syscon		: the phandle and register offset to the Complex I/O or CSI-PHY
+		  register
+ti,phy-type	: 0 -- OMAP3ISP_PHY_TYPE_COMPLEX_IO (e.g. 3430)
+		  1 -- OMAP3ISP_PHY_TYPE_CSIPHY (e.g. 3630)
+#clock-cells	: Must be 1 --- the ISP provides two external clocks,
+		  cam_xclka and cam_xclkb, at indices 0 and 1,
+		  respectively. Please find more information on common
+		  clock bindings in ../clock/clock-bindings.txt.
+
+Port nodes (optional)
+---------------------
+
+More documentation on these bindings is available in
+video-interfaces.txt in the same directory.
+
+reg		: The interface:
+		  0 - parallel (CCDC)
+		  1 - CSIPHY1 -- CSI2C / CCP2B on 3630;
+		      CSI1 -- CSIb on 3430
+		  2 - CSIPHY2 -- CSI2A / CCP2B on 3630;
+		      CSI2 -- CSIa on 3430
+
+Optional properties
+===================
+
+vdd-csiphy1-supply : voltage supply of the CSI-2 PHY 1
+vdd-csiphy2-supply : voltage supply of the CSI-2 PHY 2
+
+Endpoint nodes
+--------------
+
+lane-polarities	: lane polarity (required on CSI-2)
+		  0 -- not inverted; 1 -- inverted
+data-lanes	: an array of data lanes from 1 to 3. The length can
+		  be either 1 or 2. (required on CSI-2)
+clock-lanes	: the clock lane (from 1 to 3). (required on CSI-2)
+
+
+Example
+=======
+
+		isp@480bc000 {
+			compatible = "ti,omap3-isp";
+			reg = <0x480bc000 0x12fc
+			       0x480bd800 0x0600>;
+			interrupts = <24>;
+			iommus = <&mmu_isp>;
+			syscon = <&scm_conf 0x2f0>;
+			ti,phy-type = <OMAP3ISP_PHY_TYPE_CSIPHY>;
+			#clock-cells = <1>;
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};

Documentation/devicetree/bindings/serial/omap_serial.txt

@@ -4,7 +4,27 @@ Required properties:
 - compatible : should be "ti,omap2-uart" for OMAP2 controllers
 - compatible : should be "ti,omap3-uart" for OMAP3 controllers
 - compatible : should be "ti,omap4-uart" for OMAP4 controllers
+- reg : address and length of the register space
+- interrupts or interrupts-extended : Should contain the uart interrupt
+                                      specifier or both the interrupt
+                                      controller phandle and interrupt
+                                      specifier.
 - ti,hwmods : Must be "uart<n>", n being the instance number (1-based)
 
 Optional properties:
 - clock-frequency : frequency of the clock input to the UART
+- dmas : DMA specifier, consisting of a phandle to the DMA controller
+         node and a DMA channel number.
+- dma-names : "rx" for receive channel, "tx" for transmit channel.
+
+Example:
+
+                uart4: serial@49042000 {
+                        compatible = "ti,omap3-uart";
+                        reg = <0x49042000 0x400>;
+                        interrupts = <80>;
+                        dmas = <&sdma 81 &sdma 82>;
+                        dma-names = "tx", "rx";
+                        ti,hwmods = "uart4";
+                        clock-frequency = <48000000>;
+                };

Documentation/devicetree/bindings/sound/omap-twl4030.txt

@@ -4,9 +4,9 @@ Required properties:
 - compatible: "ti,omap-twl4030"
 - ti,model: Name of the sound card (for example "omap3beagle")
 - ti,mcbsp: phandle for the McBSP node
-- ti,codec: phandle for the twl4030 audio node
 
 Optional properties:
+- ti,codec: phandle for the twl4030 audio node
 - ti,mcbsp-voice: phandle for the McBSP node connected to the voice port of twl
 - ti, jack-det-gpio: Jack detect GPIO
 - ti,audio-routing: List of connections between audio components.
@@ -59,5 +59,4 @@ sound {
 	ti,model = "omap3beagle";
 
 	ti,mcbsp = <&mcbsp2>;
-	ti,codec = <&twl_audio>;
 };

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -77,6 +77,7 @@ giantplus	Giantplus Technology Co., Ltd.
 globalscale	Globalscale Technologies, Inc.
 gmt	Global Mixed-mode Technology, Inc.
 google	Google, Inc.
+grinn	Grinn
 gumstix	Gumstix, Inc.
 gw	Gateworks Corporation
 hannstar	HannStar Display Corporation

MAINTAINERS

@@ -7079,6 +7079,7 @@ OMAP IMAGING SUBSYSTEM (OMAP3 ISP and OMAP4 ISS)
 M:	Laurent Pinchart <laurent.pinchart@ideasonboard.com>
 L:	linux-media@vger.kernel.org
 S:	Maintained
+F:	Documentation/devicetree/bindings/media/ti,omap3isp.txt
 F:	drivers/media/platform/omap3isp/
 F:	drivers/staging/media/omap4iss/
 

arch/arm/boot/dts/Makefile

@@ -388,6 +388,8 @@ dtb-$(CONFIG_ARCH_OMAP3) += \
 	omap3-overo-storm-tobi.dtb \
 	omap3-overo-summit.dtb \
 	omap3-overo-tobi.dtb \
+	omap3-pandora-600mhz.dtb \
+	omap3-pandora-1ghz.dtb \
 	omap3-sbc-t3517.dtb \
 	omap3-sbc-t3530.dtb \
 	omap3-sbc-t3730.dtb \
@@ -403,7 +405,8 @@ dtb-$(CONFIG_SOC_AM33XX) += \
 	am335x-evmsk.dtb \
 	am335x-nano.dtb \
 	am335x-pepper.dtb \
-	am335x-lxm.dtb
+	am335x-lxm.dtb \
+	am335x-chiliboard.dtb
 dtb-$(CONFIG_ARCH_OMAP4) += \
 	omap4-duovero-parlor.dtb \
 	omap4-panda.dtb \

arch/arm/boot/dts/am335x-chiliboard.dts

+/*
+ * Copyright (C) 2015 Jablotron s.r.o. -- http://www.jablotron.com/
+ * Author: Rostislav Lisovy <lisovy@jablotron.cz>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+#include "am335x-chilisom.dtsi"
+
+/ {
+	model = "AM335x Chiliboard";
+	compatible = "grinn,am335x-chiliboard", "grinn,am335x-chilisom",
+		     "ti,am33xx";
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_gpio_pins>;
+
+		led0 {
+			label = "led0";
+			gpios = <&gpio3 7 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+			linux,default-trigger = "heartbeat";
+		};
+
+		led1 {
+			label = "led1";
+			gpios = <&gpio3 8 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+		};
+	};
+};
+
+&am33xx_pinmux {
+	usb1_drvvbus: usb1_drvvbus {
+		pinctrl-single,pins = <
+			0x234 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* usb1_drvvbus.usb1_drvvbus */
+		>;
+	};
+
+	sd_pins: pinmux_sd_card {
+		pinctrl-single,pins = <
+			0xf0 (PIN_INPUT | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */
+			0xf4 (PIN_INPUT | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */
+			0xf8 (PIN_INPUT | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */
+			0xfc (PIN_INPUT | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */
+			0x100 (PIN_INPUT | MUX_MODE0) /* mmc0_clk.mmc0_clk */
+			0x104 (PIN_INPUT | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */
+			0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */
+		>;
+	};
+
+	led_gpio_pins: led_gpio_pins {
+		pinctrl-single,pins = <
+			0x1e4 (PIN_OUTPUT | MUX_MODE7) /* emu0.gpio3_7 */
+			0x1e8 (PIN_OUTPUT | MUX_MODE7) /* emu1.gpio3_8 */
+		>;
+	};
+};
+
+&ldo4_reg {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+};
+
+/* Ethernet */
+&cpsw_emac0 {
+	phy_id = <&davinci_mdio>, <0>;
+	phy-mode = "rmii";
+};
+
+&phy_sel {
+	rmii-clock-ext;
+};
+
+/* USB */
+&usb {
+	status = "okay";
+};
+
+&usb_ctrl_mod {
+	status = "okay";
+};
+
+&usb1_phy {
+	status = "okay";
+};
+
+&usb1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb1_drvvbus>;
+
+	status = "okay";
+	dr_mode = "host";
+};
+
+&cppi41dma  {
+	status = "okay";
+};
+
+/* microSD */
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd_pins>;
+	vmmc-supply = <&ldo4_reg>;
+	bus-width = <0x4>;
+	cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};

arch/arm/boot/dts/am335x-chilisom.dtsi

+/*
+ * Copyright (C) 2015 Jablotron s.r.o. -- http://www.jablotron.com/
+ * Author: Rostislav Lisovy <lisovy@jablotron.cz>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include "am33xx.dtsi"
+
+/ {
+	model = "Grinn AM335x ChiliSOM";
+	compatible = "grinn,am335x-chilisom", "ti,am33xx";
+
+	cpus {
+		cpu@0 {
+			cpu0-supply = <&dcdc2_reg>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>; /* 512 MB */
+	};
+};
+
+&am33xx_pinmux {
+	pinctrl-names = "default";
+
+	i2c0_pins: pinmux_i2c0_pins {
+		pinctrl-single,pins = <
+			0x188 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c0_sda.i2c0_sda */
+			0x18c (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c0_scl.i2c0_scl */
+		>;
+	};
+
+	uart0_pins: pinmux_uart0_pins {
+		pinctrl-single,pins = <
+			0x170 (PIN_INPUT_PULLUP | MUX_MODE0)	/* uart0_rxd.uart0_rxd */
+			0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart0_txd.uart0_txd */
+		>;
+	};
+
+	cpsw_default: cpsw_default {
+		pinctrl-single,pins = <
+			/* Slave 1 */
+			0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1)  /* mii1_crs.rmii1_crs */
+			0x110 (PIN_INPUT_PULLUP | MUX_MODE1)	/* mii1_rxerr.rmii1_rxerr */
+			0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE1)	/* mii1_txen.rmii1_txen */
+			0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE1)	/* mii1_txd1.rmii1_txd1 */
+			0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE1)	/* mii1_txd0.rmii1_txd0 */
+			0x13c (PIN_INPUT_PULLUP | MUX_MODE1)	/* mii1_rxd1.rmii1_rxd1 */
+			0x140 (PIN_INPUT_PULLUP | MUX_MODE1)	/* mii1_rxd0.rmii1_rxd0 */
+			0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* rmii1_ref_clk.rmii_ref_clk */
+		>;
+	};
+
+	cpsw_sleep: cpsw_sleep {
+		pinctrl-single,pins = <
+			/* Slave 1 reset value */
+			0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
+
+	davinci_mdio_default: davinci_mdio_default {
+		pinctrl-single,pins = <
+			/* mdio_data.mdio_data */
+			0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)
+			/* mdio_clk.mdio_clk */
+			0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0)
+		>;
+	};
+
+	davinci_mdio_sleep: davinci_mdio_sleep {
+		pinctrl-single,pins = <
+			/* MDIO reset value */
+			0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
+
+	nandflash_pins: nandflash_pins {
+		pinctrl-single,pins = <
+			0x00 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad0.gpmc_ad0 */
+			0x04 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad1.gpmc_ad1 */
+			0x08 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad2.gpmc_ad2 */
+			0x0c (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad3.gpmc_ad3 */
+			0x10 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad4.gpmc_ad4 */
+			0x14 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad5.gpmc_ad5 */
+			0x18 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad6.gpmc_ad6 */
+			0x1c (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad7.gpmc_ad7 */
+
+			0x70 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_wait0.gpmc_wait0 */
+			0x7c (PIN_OUTPUT_PULLUP | MUX_MODE0)	/* gpmc_csn0.gpmc_csn0 */
+			0x90 (PIN_OUTPUT_PULLUP | MUX_MODE0)	/* gpmc_advn_ale.gpmc_advn_ale */
+			0x94 (PIN_OUTPUT_PULLUP | MUX_MODE0)	/* gpmc_oen_ren.gpmc_oen_ren */
+			0x98 (PIN_OUTPUT_PULLUP | MUX_MODE0)	/* gpmc_wen.gpmc_wen */
+			0x9c (PIN_OUTPUT_PULLUP | MUX_MODE0)	/* gpmc_be0n_cle.gpmc_be0n_cle */
+		>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+
+	status = "okay";
+	clock-frequency = <400000>;
+
+	tps: tps@24 {
+		reg = <0x24>;
+	};
+
+};
+
+/include/ "tps65217.dtsi"
+
+&tps {
+	regulators {
+		dcdc1_reg: regulator@0 {
+			regulator-name = "vdds_dpr";
+			regulator-always-on;
+		};
+
+		dcdc2_reg: regulator@1 {
+			/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
+			regulator-name = "vdd_mpu";
+			regulator-min-microvolt = <925000>;
+			regulator-max-microvolt = <1325000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		dcdc3_reg: regulator@2 {
+			/* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
+			regulator-name = "vdd_core";
+			regulator-min-microvolt = <925000>;
+			regulator-max-microvolt = <1150000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		ldo1_reg: regulator@3 {
+			regulator-name = "vio,vrtc,vdds";
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		ldo2_reg: regulator@4 {
+			regulator-name = "vdd_3v3aux";
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		ldo3_reg: regulator@5 {
+			regulator-name = "vdd_1v8";
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		ldo4_reg: regulator@6 {
+			regulator-name = "vdd_3v3d";
+			regulator-boot-on;
+			regulator-always-on;
+		};
+	};
+};
+
+/* Ethernet MAC */
+&mac {
+	slaves = <1>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&cpsw_default>;
+	pinctrl-1 = <&cpsw_sleep>;
+	status = "okay";
+};
+
+&davinci_mdio {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&davinci_mdio_default>;
+	pinctrl-1 = <&davinci_mdio_sleep>;
+	status = "okay";
+};
+
+/* NAND Flash */
+&elm {
+	status = "okay";
+};
+
+&gpmc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&nandflash_pins>;
+	ranges = <0 0 0x08000000 0x01000000>; /* CS0 0 @addr 0x08000000, size 0x01000000 */
+	nand@0,0 {
+		reg = <0 0 4>;	/* CS0, offset 0, IO size 4 */
+		ti,nand-ecc-opt = "bch8";
+		ti,elm-id = <&elm>;
+		nand-bus-width = <8>;
+		gpmc,device-width = <1>;
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <44>;
+		gpmc,cs-wr-off-ns = <44>;
+		gpmc,adv-on-ns = <6>;
+		gpmc,adv-rd-off-ns = <34>;
+		gpmc,adv-wr-off-ns = <44>;
+		gpmc,we-on-ns = <0>;
+		gpmc,we-off-ns = <40>;
+		gpmc,oe-on-ns = <0>;
+		gpmc,oe-off-ns = <54>;
+		gpmc,access-ns = <64>;
+		gpmc,rd-cycle-ns = <82>;
+		gpmc,wr-cycle-ns = <82>;
+		gpmc,wait-on-read = "true";
+		gpmc,wait-on-write = "true";
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <0>;
+		gpmc,clk-activation-ns = <0>;
+		gpmc,wait-monitoring-ns = <0>;
+		gpmc,wr-access-ns = <40>;
+		gpmc,wr-data-mux-bus-ns = <0>;
+	};
+};

arch/arm/boot/dts/am335x-nano.dts

@@ -213,7 +213,9 @@ &i2c0 {
 	pinctrl-0 = <&i2c0_pins>;
 
 	gpio@20 {
-		compatible = "mcp,mcp23017";
+		compatible = "microchip,mcp23017";
+		gpio-controller;
+		#gpio-cells = <2>;
 		reg = <0x20>;
 	};
 
@@ -222,7 +224,7 @@ tps: tps@24 {
 	};
 
 	eeprom@53 {
-		compatible = "mcp,24c02";
+		compatible = "microchip,24c02";
 		reg = <0x53>;
 		pagesize = <8>;
 	};
@@ -297,8 +299,8 @@ MTD partition table
 		|            |-->0x004FFFFF-> Kernel end
 		|            |-->0x00500000-> File system start
 		|            |
-		|            |-->0x014FFFFF-> File system end
-		|            |-->0x01500000-> User data start
+		|            |-->0x01FFFFFF-> File system end
+		|            |-->0x02000000-> User data start
 		|            |
 		|            |-->0x03FFFFFF-> User data end
 		|            |-->0x04000000-> Data storage start
@@ -327,12 +329,12 @@ partition@3 {
 
 		partition@4 {
 			label = "rootfs";
-			reg = <0x00500000 0x01000000>; /* 16MB */
+			reg = <0x00500000 0x01b00000>; /* 27MB */
 		};
 
 		partition@5 {
 			label = "user";
-			reg = <0x01500000 0x02b00000>; /* 43MB */
+			reg = <0x02000000 0x02000000>; /* 32MB */
 		};
 
 		partition@6 {
@@ -343,7 +345,7 @@ partition@6 {
 };
 
 &mac {
-	dual_emac = <1>;
+	dual_emac;
 	status = "okay";
 };
 
@@ -353,11 +355,13 @@ &davinci_mdio {
 
 &cpsw_emac0 {
 	phy_id = <&davinci_mdio>, <0>;
+	phy-mode = "mii";
 	dual_emac_res_vlan = <1>;
 };
 
 &cpsw_emac1 {
 	phy_id = <&davinci_mdio>, <1>;
+	phy-mode = "mii";
 	dual_emac_res_vlan = <2>;
 };
 

arch/arm/boot/dts/am4372.dtsi

@@ -897,7 +897,7 @@ qspi: qspi@47900000 {
 		};
 
 		hdq: hdq@48347000 {
-			compatible = "ti,am43xx-hdq";
+			compatible = "ti,am4372-hdq";
 			reg = <0x48347000 0x1000>;
 			interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&func_12m_clk>;

arch/arm/boot/dts/am437x-idk-evm.dts

@@ -133,6 +133,20 @@ i2c0_pins_sleep: i2c0_pins_sleep {
 		>;
 	};
 
+	i2c2_pins_default: i2c2_pins_default {
+		pinctrl-single,pins = <
+			0x1e8 (PIN_INPUT | SLEWCTRL_FAST | MUX_MODE3) /* cam1_data1.i2c2_scl */
+			0x1ec (PIN_INPUT | SLEWCTRL_FAST | MUX_MODE3) /* cam1_data0.i2c2_sda */
+		>;
+	};
+
+	i2c2_pins_sleep: i2c2_pins_sleep {
+		pinctrl-single,pins = <
+			0x1e8 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x1ec (PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
+
 	mmc1_pins_default: pinmux_mmc1_pins_default {
 		pinctrl-single,pins = <
 			0x100 (PIN_INPUT | MUX_MODE0) /* mmc0_clk.mmc0_clk */
@@ -263,6 +277,14 @@ tps: tps62362@60 {
 	};
 };
 
+&i2c2 {
+	status = "okay";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c2_pins_default>;
+	pinctrl-1 = <&i2c2_pins_sleep>;
+	clock-frequency = <100000>;
+};
+
 &epwmss0 {
 	status = "okay";
 };

arch/arm/boot/dts/am57xx-beagle-x15.dts

@@ -8,7 +8,6 @@
 /dts-v1/;
 
 #include "dra74x.dtsi"
-#include <dt-bindings/clk/ti-dra7-atl.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 
@@ -551,6 +550,14 @@ &usb1 {
 	pinctrl-0 = <&usb1_pins>;
 };
 
+&omap_dwc3_1 {
+	extcon = <&extcon_usb1>;
+};
+
+&omap_dwc3_2 {
+	extcon = <&extcon_usb2>;
+};
+
 &usb2 {
 	dr_mode = "peripheral";
 };

arch/arm/boot/dts/dm8168-evm.dts

@@ -29,22 +29,22 @@ vmmcsd_fixed: fixedregulator@0 {
 &dm816x_pinmux {
 	mcspi1_pins: pinmux_mcspi1_pins {
 		pinctrl-single,pins = <
-			DM816X_IOPAD(0x0a94, PIN_INPUT | MUX_MODE0)	/* SPI_SCLK */
-			DM816X_IOPAD(0x0a98, PIN_OUTPUT | MUX_MODE0)	/* SPI_SCS0 */
-			DM816X_IOPAD(0x0aa8, PIN_INPUT | MUX_MODE0)	/* SPI_D0 */
-			DM816X_IOPAD(0x0aac, PIN_INPUT | MUX_MODE0)	/* SPI_D1 */
+			DM816X_IOPAD(0x0a94, MUX_MODE0)			/* SPI_SCLK */
+			DM816X_IOPAD(0x0a98, MUX_MODE0)			/* SPI_SCS0 */
+			DM816X_IOPAD(0x0aa8, MUX_MODE0)			/* SPI_D0 */
+			DM816X_IOPAD(0x0aac, MUX_MODE0)			/* SPI_D1 */
 		>;
 	};
 
 	usb0_pins: pinmux_usb0_pins {
 		pinctrl-single,pins = <
-			DM816X_IOPAD(0x0d00, MUX_MODE0)			/* USB0_DRVVBUS */
+			DM816X_IOPAD(0x0d04, MUX_MODE0)			/* USB0_DRVVBUS */
 		>;
 	};
 
-	usb1_pins: pinmux_usb0_pins {
+	usb1_pins: pinmux_usb1_pins {
 		pinctrl-single,pins = <
-			DM816X_IOPAD(0x0d04, MUX_MODE0)			/* USB1_DRVVBUS */
+			DM816X_IOPAD(0x0d08, MUX_MODE0)			/* USB1_DRVVBUS */
 		>;
 	};
 };

arch/arm/boot/dts/dm816x.dtsi

@@ -386,6 +386,29 @@ usb0: usb@47401000 {
 				mentor,num-eps = <16>;
 				mentor,ram-bits = <12>;
 				mentor,power = <500>;
+
+				dmas = <&cppi41dma  0 0 &cppi41dma  1 0
+					&cppi41dma  2 0 &cppi41dma  3 0
+					&cppi41dma  4 0 &cppi41dma  5 0
+					&cppi41dma  6 0 &cppi41dma  7 0
+					&cppi41dma  8 0 &cppi41dma  9 0
+					&cppi41dma 10 0 &cppi41dma 11 0
+					&cppi41dma 12 0 &cppi41dma 13 0
+					&cppi41dma 14 0 &cppi41dma  0 1
+					&cppi41dma  1 1 &cppi41dma  2 1
+					&cppi41dma  3 1 &cppi41dma  4 1
+					&cppi41dma  5 1 &cppi41dma  6 1
+					&cppi41dma  7 1 &cppi41dma  8 1
+					&cppi41dma  9 1 &cppi41dma 10 1
+					&cppi41dma 11 1 &cppi41dma 12 1
+					&cppi41dma 13 1 &cppi41dma 14 1>;
+				dma-names =
+					"rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7",
+					"rx8", "rx9", "rx10", "rx11", "rx12", "rx13",
+					"rx14", "rx15",
+					"tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7",
+					"tx8", "tx9", "tx10", "tx11", "tx12", "tx13",
+					"tx14", "tx15";
 			};
 
 			usb1: usb@47401800 {
@@ -403,6 +426,43 @@ usb1: usb@47401800 {
 				mentor,num-eps = <16>;
 				mentor,ram-bits = <12>;
 				mentor,power = <500>;
+
+				dmas = <&cppi41dma 15 0 &cppi41dma 16 0
+					&cppi41dma 17 0 &cppi41dma 18 0
+					&cppi41dma 19 0 &cppi41dma 20 0
+					&cppi41dma 21 0 &cppi41dma 22 0
+					&cppi41dma 23 0 &cppi41dma 24 0
+					&cppi41dma 25 0 &cppi41dma 26 0
+					&cppi41dma 27 0 &cppi41dma 28 0
+					&cppi41dma 29 0 &cppi41dma 15 1
+					&cppi41dma 16 1 &cppi41dma 17 1
+					&cppi41dma 18 1 &cppi41dma 19 1
+					&cppi41dma 20 1 &cppi41dma 21 1
+					&cppi41dma 22 1 &cppi41dma 23 1
+					&cppi41dma 24 1 &cppi41dma 25 1
+					&cppi41dma 26 1 &cppi41dma 27 1
+					&cppi41dma 28 1 &cppi41dma 29 1>;
+				dma-names =
+					"rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7",
+					"rx8", "rx9", "rx10", "rx11", "rx12", "rx13",
+					"rx14", "rx15",
+					"tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7",
+					"tx8", "tx9", "tx10", "tx11", "tx12", "tx13",
+					"tx14", "tx15";
+			};
+
+			cppi41dma: dma-controller@47402000 {
+				compatible = "ti,am3359-cppi41";
+				reg =  <0x47400000 0x1000
+					0x47402000 0x1000
+					0x47403000 0x1000
+					0x47404000 0x4000>;
+				reg-names = "glue", "controller", "scheduler", "queuemgr";
+				interrupts = <17>;
+				interrupt-names = "glue";
+				#dma-cells = <2>;
+				#dma-channels = <30>;
+				#dma-requests = <256>;
 			};
 		};
 

arch/arm/boot/dts/dra7-evm.dts

@@ -543,6 +543,14 @@ partition@9 {
 	};
 };
 
+&omap_dwc3_1 {
+	extcon = <&extcon_usb1>;
+};
+
+&omap_dwc3_2 {
+	extcon = <&extcon_usb2>;
+};
+
 &usb1 {
 	dr_mode = "peripheral";
 	pinctrl-names = "default";

arch/arm/boot/dts/dra7.dtsi

@@ -700,7 +700,6 @@ timer5: timer@48820000 {
 			reg = <0x48820000 0x80>;
 			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "timer5";
-			ti,timer-dsp;
 		};
 
 		timer6: timer@48822000 {
@@ -708,8 +707,6 @@ timer6: timer@48822000 {
 			reg = <0x48822000 0x80>;
 			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "timer6";
-			ti,timer-dsp;
-			ti,timer-pwm;
 		};
 
 		timer7: timer@48824000 {
@@ -717,7 +714,6 @@ timer7: timer@48824000 {
 			reg = <0x48824000 0x80>;
 			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "timer7";
-			ti,timer-dsp;
 		};
 
 		timer8: timer@48826000 {
@@ -725,8 +721,6 @@ timer8: timer@48826000 {
 			reg = <0x48826000 0x80>;
 			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "timer8";
-			ti,timer-dsp;
-			ti,timer-pwm;
 		};
 
 		timer9: timer@4803e000 {
@@ -748,7 +742,6 @@ timer11: timer@48088000 {
 			reg = <0x48088000 0x80>;
 			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "timer11";
-			ti,timer-pwm;
 		};
 
 		timer13: timer@48828000 {

arch/arm/boot/dts/dra72-evm.dts

@@ -380,6 +380,14 @@ &usb2_phy2 {
 	phy-supply = <&ldo4_reg>;
 };
 
+&omap_dwc3_1 {
+	extcon = <&extcon_usb1>;
+};
+
+&omap_dwc3_2 {
+	extcon = <&extcon_usb2>;
+};
+
 &usb1 {
 	dr_mode = "peripheral";
 	pinctrl-names = "default";

arch/arm/boot/dts/dra7xx-clocks.dtsi

@@ -1421,6 +1421,14 @@ l3init_60m_fclk: l3init_60m_fclk {
 		ti,dividers = <1>, <8>;
 	};
 
+	clkout2_clk: clkout2_clk {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&clkoutmux2_clk_mux>;
+		ti,bit-shift = <8>;
+		reg = <0x06b0>;
+	};
+
 	l3init_960m_gfclk: l3init_960m_gfclk {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";

arch/arm/boot/dts/omap3-beagle-xm.dts

@@ -60,7 +60,6 @@ sound {
 		ti,model = "omap3beagle";
 
 		ti,mcbsp = <&mcbsp2>;
-		ti,codec = <&twl_audio>;
 	};
 
 	gpio_keys {

arch/arm/boot/dts/omap3-beagle.dts

@@ -71,7 +71,6 @@ sound {
 		ti,model = "omap3beagle";
 
 		ti,mcbsp = <&mcbsp2>;
-		ti,codec = <&twl_audio>;
 	};
 
 	gpio_keys {
@@ -379,3 +378,55 @@ venc_out: endpoint {
 		};
 	};
 };
+
+&gpmc {
+	status = "ok";
+	ranges = <0 0 0x30000000 0x1000000>;	/* CS0 space, 16MB */
+
+	/* Chip select 0 */
+	nand@0,0 {
+		reg = <0 0 4>;		/* NAND I/O window, 4 bytes */
+		interrupts = <20>;
+		ti,nand-ecc-opt = "ham1";
+		nand-bus-width = <16>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		gpmc,device-width = <2>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <36>;
+		gpmc,cs-wr-off-ns = <36>;
+		gpmc,adv-on-ns = <6>;
+		gpmc,adv-rd-off-ns = <24>;
+		gpmc,adv-wr-off-ns = <36>;
+		gpmc,oe-on-ns = <6>;
+		gpmc,oe-off-ns = <48>;
+		gpmc,we-on-ns = <6>;
+		gpmc,we-off-ns = <30>;
+		gpmc,rd-cycle-ns = <72>;
+		gpmc,wr-cycle-ns = <72>;
+		gpmc,access-ns = <54>;
+		gpmc,wr-access-ns = <30>;
+
+		partition@0 {
+			label = "X-Loader";
+			reg = <0 0x80000>;
+		};
+		partition@80000 {
+			label = "U-Boot";
+			reg = <0x80000 0x1e0000>;
+		};
+		partition@1c0000 {
+			label = "U-Boot Env";
+			reg = <0x260000 0x20000>;
+		};
+		partition@280000 {
+			label = "Kernel";
+			reg = <0x280000 0x400000>;
+		};
+		partition@780000 {
+			label = "Filesystem";
+			reg = <0x680000 0xf980000>;
+		};
+	};
+};

arch/arm/boot/dts/omap3-cm-t3x30.dtsi

@@ -16,7 +16,6 @@ sound {
 		ti,model = "cm-t35";
 
 		ti,mcbsp = <&mcbsp2>;
-		ti,codec = <&twl_audio>;
 	};
 };
 

arch/arm/boot/dts/omap3-devkit8000.dts

@@ -48,7 +48,6 @@ sound {
 		ti,model = "devkit8000";
 
 		ti,mcbsp = <&mcbsp2>;
-		ti,codec = <&twl_audio>;
 		ti,audio-routing =
 			"Ext Spk", "PREDRIVEL",
 			"Ext Spk", "PREDRIVER",

arch/arm/boot/dts/omap3-gta04.dtsi

@@ -46,7 +46,6 @@ sound {
 		ti,model = "gta04";
 
 		ti,mcbsp = <&mcbsp2>;
-		ti,codec = <&twl_audio>;
 	};
 
 	spi_lcd {

arch/arm/boot/dts/omap3-igep.dtsi

@@ -22,7 +22,6 @@ sound {
 		compatible = "ti,omap-twl4030";
 		ti,model = "igep2";
 		ti,mcbsp = <&mcbsp2>;
-		ti,codec = <&twl_audio>;
 	};
 
 	vdd33: regulator-vdd33 {

arch/arm/boot/dts/omap3-lilly-a83x.dtsi

@@ -38,7 +38,6 @@ sound {
 		ti,model = "lilly-a83x";
 
 		ti,mcbsp = <&mcbsp2>;
-		ti,codec = <&twl_audio>;
 	};
 
 	reg_vcc3: vcc3 {

arch/arm/boot/dts/omap3-n9.dts

@@ -16,3 +16,40 @@ / {
 	model = "Nokia N9";
 	compatible = "nokia,omap3-n9", "ti,omap36xx", "ti,omap3";
 };
+
+&i2c2 {
+	smia_1: camera@10 {
+		compatible = "nokia,smia";
+		reg = <0x10>;
+		/* No reset gpio */
+		vana-supply = <&vaux3>;
+		clocks = <&isp 0>;
+		clock-frequency = <9600000>;
+		nokia,nvm-size = <(16 * 64)>;
+		port {
+			smia_1_1: endpoint {
+				link-frequencies = /bits/ 64 <199200000 210000000 499200000>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+				remote-endpoint = <&csi2a_ep>;
+			};
+		};
+	};
+};
+
+&isp {
+	vdd-csiphy1-supply = <&vaux2>;
+	vdd-csiphy2-supply = <&vaux2>;
+	ports {
+		port@2 {
+			reg = <2>;
+			csi2a_ep: endpoint {
+				remote-endpoint = <&smia_1_1>;
+				clock-lanes = <2>;
+				data-lanes = <1 3>;
+				crc = <1>;
+				lane-polarities = <1 1 1>;
+			};
+		};
+	};
+};

arch/arm/boot/dts/omap3-n900.dts

@@ -9,9 +9,23 @@
 
 /dts-v1/;
 
-#include "omap34xx-hs.dtsi"
+#include "omap34xx.dtsi"
 #include <dt-bindings/input/input.h>
 
+/*
+ * Default secure signed bootloader (Nokia X-Loader) does not enable L3 firewall
+ * for omap AES HW crypto support. When linux kernel try to access memory of AES
+ * blocks then kernel receive "Unhandled fault: external abort on non-linefetch"
+ * and crash. Until somebody fix omap-aes.c and omap_hwmod_3xxx_data.c code (no
+ * crash anymore) omap AES support will be disabled for all Nokia N900 devices.
+ * There is "unofficial" version of bootloader which enables AES in L3 firewall
+ * but it is not widely used and to prevent kernel crash rather AES is disabled.
+ * There is also no runtime detection code if AES is disabled in L3 firewall...
+ */
+&aes {
+	status = "disabled";
+};
+
 / {
 	model = "Nokia N900";
 	compatible = "nokia,omap3-n900", "ti,omap3430", "ti,omap3";

arch/arm/boot/dts/omap3-n950-n9.dtsi

@@ -8,7 +8,7 @@
  * published by the Free Software Foundation.
  */
 
-#include "omap36xx-hs.dtsi"
+#include "omap36xx.dtsi"
 
 / {
 	cpus {

arch/arm/boot/dts/omap3-n950.dts

@@ -16,3 +16,40 @@ / {
 	model = "Nokia N950";
 	compatible = "nokia,omap3-n950", "ti,omap36xx", "ti,omap3";
 };
+
+&i2c2 {
+	smia_1: camera@10 {
+		compatible = "nokia,smia";
+		reg = <0x10>;
+		/* No reset gpio */
+		vana-supply = <&vaux3>;
+		clocks = <&isp 0>;
+		clock-frequency = <9600000>;
+		nokia,nvm-size = <(16 * 64)>;
+		port {
+			smia_1_1: endpoint {
+				link-frequencies = /bits/ 64 <210000000 333600000 398400000>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+				remote-endpoint = <&csi2a_ep>;
+			};
+		};
+	};
+};
+
+&isp {
+	vdd-csiphy1-supply = <&vaux2>;
+	vdd-csiphy2-supply = <&vaux2>;
+	ports {
+		port@2 {
+			reg = <2>;
+			csi2a_ep: endpoint {
+				remote-endpoint = <&smia_1_1>;
+				clock-lanes = <2>;
+				data-lanes = <3 1>;
+				crc = <1>;
+				lane-polarities = <1 1 1>;
+			};
+		};
+	};
+};

arch/arm/boot/dts/omap3-overo-base.dtsi

@@ -27,7 +27,6 @@ sound {
 		ti,model = "overo";
 
 		ti,mcbsp = <&mcbsp2>;
-		ti,codec = <&twl_audio>;
 	};
 
 	/* HS USB Port 2 Power */

arch/arm/boot/dts/omap3-pandora-1ghz.dts

+/*
+ * Copyright (C) 2015
+ *   Nikolaus Schaller <hns@goldelico.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * device tree for OpenPandora 1GHz with DM3730
+ */
+
+/dts-v1/;
+
+#include "omap36xx.dtsi"
+#include "omap3-pandora-common.dtsi"
+
+/ {
+	model = "Pandora Handheld Console 1GHz";
+
+	compatible = "ti,omap36xx", "ti,omap3";
+};
+
+&omap3_pmx_core2 {
+
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		&hsusb2_2_pins
+		&control_pins
+	>;
+
+	hsusb2_2_pins: pinmux_hsusb2_2_pins {
+		pinctrl-single,pins = <
+			OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)		/* etk_d10.hsusb2_clk */
+			OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)		/* etk_d11.hsusb2_stp */
+			OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d12.hsusb2_dir */
+			OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d13.hsusb2_nxt */
+			OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d14.hsusb2_data0 */
+			OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d15.hsusb2_data1 */
+		>;
+	};
+
+	mmc3_pins: pinmux_mmc3_pins {
+		pinctrl-single,pins = <
+			OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_clk.sdmmc3_clk */
+			OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_ctl.sdmmc3_cmd */
+			OMAP3630_CORE2_IOPAD(0x25e2, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_d3.sdmmc3_dat3 */
+			OMAP3630_CORE2_IOPAD(0x25e4, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_d4.sdmmc3_dat0 */
+			OMAP3630_CORE2_IOPAD(0x25e6, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_d5.sdmmc3_dat1 */
+			OMAP3630_CORE2_IOPAD(0x25e8, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_d6.sdmmc3_dat2 */
+		>;
+	};
+
+	control_pins: pinmux_control_pins {
+		pinctrl-single,pins = <
+			OMAP3630_CORE2_IOPAD(0x25dc, PIN_INPUT_PULLDOWN | MUX_MODE4)	/* etk_d0.gpio_14 =  HP_SHUTDOWN */
+			OMAP3630_CORE2_IOPAD(0x25de, PIN_OUTPUT | MUX_MODE4)		/* etk_d1.gpio_15 =  BT_SHUTDOWN */
+			OMAP3630_CORE2_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE4)		/* etk_d2.gpio_16 =  RESET_USB_HOST */
+			OMAP3630_CORE2_IOPAD(0x25ea, PIN_INPUT | MUX_MODE4)		/* etk_d7.gpio_21 =  WIFI IRQ */
+			OMAP3630_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4)		/* etk_d8.gpio_22 =  MSECURE */
+			OMAP3630_CORE2_IOPAD(0x25ee, PIN_OUTPUT | MUX_MODE4)		/* etk_d9.gpio_23 =  WIFI_POWER */
+			OMAP3_WKUP_IOPAD(0x2a54, PIN_INPUT | MUX_MODE4)   		/* reserved.gpio_127 = MMC2_WP */
+			OMAP3_WKUP_IOPAD(0x2a56, PIN_INPUT | MUX_MODE4)   		/* reserved.gpio_126 = MMC1_WP */
+			OMAP3_WKUP_IOPAD(0x2a58, PIN_OUTPUT | MUX_MODE4)   		/* reserved.gpio_128 = LED_MMC1 */
+			OMAP3_WKUP_IOPAD(0x2a5a, PIN_OUTPUT | MUX_MODE4)   		/* reserved.gpio_129 = LED_MMC2 */
+
+		>;
+	};
+};

arch/arm/boot/dts/omap3-pandora-600mhz.dts

+/*
+ * Copyright (C) 2015
+ *   Nikolaus Schaller <hns@goldelico.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * device tree for OpenPandora with OMAP3530
+ */
+
+/dts-v1/;
+
+#include "omap34xx.dtsi"
+#include "omap3-pandora-common.dtsi"
+
+/ {
+	model = "Pandora Handheld Console";
+
+	compatible = "ti,omap3";
+};
+
+&omap3_pmx_core2 {
+
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		&hsusb2_2_pins
+		&control_pins
+	>;
+
+	hsusb2_2_pins: pinmux_hsusb2_2_pins {
+		pinctrl-single,pins = <
+			OMAP3430_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)		/* etk_d10.hsusb2_clk */
+			OMAP3430_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)		/* etk_d11.hsusb2_stp */
+			OMAP3430_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d12.hsusb2_dir */
+			OMAP3430_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d13.hsusb2_nxt */
+			OMAP3430_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d14.hsusb2_data0 */
+			OMAP3430_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d15.hsusb2_data1 */
+		>;
+	};
+
+	mmc3_pins: pinmux_mmc3_pins {
+		pinctrl-single,pins = <
+			OMAP3430_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_clk.sdmmc3_clk */
+			OMAP3430_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_ctl.sdmmc3_cmd */
+			OMAP3430_CORE2_IOPAD(0x25e2, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_d3.sdmmc3_dat3 */
+			OMAP3430_CORE2_IOPAD(0x25e4, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_d4.sdmmc3_dat0 */
+			OMAP3430_CORE2_IOPAD(0x25e6, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_d5.sdmmc3_dat1 */
+			OMAP3430_CORE2_IOPAD(0x25e8, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_d6.sdmmc3_dat2 */
+		>;
+	};
+
+	control_pins: pinmux_control_pins {
+		pinctrl-single,pins = <
+			OMAP3430_CORE2_IOPAD(0x25dc, PIN_INPUT_PULLDOWN | MUX_MODE4)	/* etk_d0.gpio_14 =  HP_SHUTDOWN */
+			OMAP3430_CORE2_IOPAD(0x25de, PIN_OUTPUT | MUX_MODE4)		/* etk_d1.gpio_15 =  BT_SHUTDOWN */
+			OMAP3430_CORE2_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE4)		/* etk_d2.gpio_16 =  RESET_USB_HOST */
+			OMAP3430_CORE2_IOPAD(0x25ea, PIN_INPUT | MUX_MODE4)		/* etk_d7.gpio_21 =  WIFI IRQ */
+			OMAP3430_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4)		/* etk_d8.gpio_22 =  MSECURE */
+			OMAP3430_CORE2_IOPAD(0x25ee, PIN_OUTPUT | MUX_MODE4)		/* etk_d9.gpio_23 =  WIFI_POWER */
+		>;
+	};
+};

arch/arm/boot/dts/omap3-tao3530.dtsi

@@ -8,7 +8,16 @@
  */
 /dts-v1/;
 
-#include "omap34xx-hs.dtsi"
+#include "omap34xx.dtsi"
+
+/* Secure omaps have some devices inaccessible depending on the firmware */
+&aes {
+	status = "disabled";
+};
+
+&sham {
+	status = "disabled";
+};
 
 / {
 	cpus {
@@ -45,7 +54,6 @@ sound {
 
 		/* McBSP2 is used for onboard sound, same as on beagle */
 		ti,mcbsp = <&mcbsp2>;
-		ti,codec = <&twl_audio>;
 	};
 
 	/* Regulator to enable/switch the vcc of the Wifi module */

arch/arm/boot/dts/omap34xx-hs.dtsi

-/* Disabled modules for secure omaps */
-
-#include "omap34xx.dtsi"
-
-/* Secure omaps have some devices inaccessible depending on the firmware */
-&aes {
-	status = "disabled";
-};
-
-&sham {
-	status = "disabled";
-};
-
-&timer12 {
-	status = "disabled";
-};

arch/arm/boot/dts/omap34xx.dtsi

@@ -8,6 +8,8 @@
  * kind, whether express or implied.
  */
 
+#include <dt-bindings/media/omap3-isp.h>
+
 #include "omap3.dtsi"
 
 / {
@@ -37,6 +39,21 @@ omap3_pmx_core2: pinmux@480025d8 {
 			pinctrl-single,register-width = <16>;
 			pinctrl-single,function-mask = <0xff1f>;
 		};
+
+		isp: isp@480bc000 {
+			compatible = "ti,omap3-isp";
+			reg = <0x480bc000 0x12fc
+			       0x480bd800 0x017c>;
+			interrupts = <24>;
+			iommus = <&mmu_isp>;
+			syscon = <&scm_conf 0xdc>;
+			ti,phy-type = <OMAP3ISP_PHY_TYPE_COMPLEX_IO>;
+			#clock-cells = <1>;
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
 	};
 };
 

arch/arm/boot/dts/omap36xx-hs.dtsi

-/* Disabled modules for secure omaps */
-
-#include "omap36xx.dtsi"
-
-/* Secure omaps have some devices inaccessible depending on the firmware */
-&aes {
-	status = "disabled";
-};
-
-&sham {
-	status = "disabled";
-};
-
-&timer12 {
-	status = "disabled";
-};

arch/arm/boot/dts/omap36xx.dtsi

@@ -8,6 +8,8 @@
  * kind, whether express or implied.
  */
 
+#include <dt-bindings/media/omap3-isp.h>
+
 #include "omap3.dtsi"
 
 / {
@@ -69,6 +71,21 @@ omap3_pmx_core2: pinmux@480025a0 {
 			pinctrl-single,register-width = <16>;
 			pinctrl-single,function-mask = <0xff1f>;
 		};
+
+		isp: isp@480bc000 {
+			compatible = "ti,omap3-isp";
+			reg = <0x480bc000 0x12fc
+			       0x480bd800 0x0600>;
+			interrupts = <24>;
+			iommus = <&mmu_isp>;
+			syscon = <&scm_conf 0x2f0>;
+			ti,phy-type = <OMAP3ISP_PHY_TYPE_CSIPHY>;
+			#clock-cells = <1>;
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
 	};
 };
 

include/dt-bindings/media/omap3-isp.h

+/*
+ * include/dt-bindings/media/omap3-isp.h
+ *
+ * Copyright (C) 2015 Sakari Ailus
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ */
+
+#ifndef __DT_BINDINGS_OMAP3_ISP_H__
+#define __DT_BINDINGS_OMAP3_ISP_H__
+
+#define OMAP3ISP_PHY_TYPE_COMPLEX_IO	0
+#define OMAP3ISP_PHY_TYPE_CSIPHY	1
+
+#endif /* __DT_BINDINGS_OMAP3_ISP_H__ */