Commit 326e5751 authored by Dongjin Kim's avatar Dongjin Kim Committed by Kevin Hilman

arm64: dts: meson-sm1: add support for Hardkernel ODROID-C4

Add the board support for the Hardkernel Odroid-C4 single board computer.

The Odroid-C4 is the Odroid-C2 successor with same form factor, but using
a modern Amlogic S905X3 (SM1) SoC and 4x USB3 ports.
Signed-off-by: default avatarDongjin Kim <tobetter@gmail.com>
Signed-off-by: default avatarNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: default avatarKevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200506080702.6645-3-narmstrong@baylibre.com
parent 838f0905
...@@ -40,4 +40,5 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxm-s912-libretech-pc.dtb ...@@ -40,4 +40,5 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxm-s912-libretech-pc.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxm-vega-s96.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxm-vega-s96.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-sm1-sei610.dtb dtb-$(CONFIG_ARCH_MESON) += meson-sm1-sei610.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-sm1-khadas-vim3l.dtb dtb-$(CONFIG_ARCH_MESON) += meson-sm1-khadas-vim3l.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-sm1-odroid-c4.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-a1-ad401.dtb dtb-$(CONFIG_ARCH_MESON) += meson-a1-ad401.dtb
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (c) 2020 Dongjin Kim <tobetter@gmail.com>
*/
/dts-v1/;
#include "meson-sm1.dtsi"
#include <dt-bindings/gpio/meson-g12a-gpio.h>
#include <dt-bindings/leds/common.h>
/ {
compatible = "hardkernel,odroid-c4", "amlogic,sm1";
model = "Hardkernel ODROID-C4";
aliases {
serial0 = &uart_AO;
ethernet0 = &ethmac;
};
chosen {
stdout-path = "serial0:115200n8";
};
memory@0 {
device_type = "memory";
reg = <0x0 0x0 0x0 0x40000000>;
};
emmc_pwrseq: emmc-pwrseq {
compatible = "mmc-pwrseq-emmc";
reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
};
leds {
compatible = "gpio-leds";
led-blue {
color = <LED_COLOR_ID_BLUE>;
function = LED_FUNCTION_STATUS;
gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
panic-indicator;
};
};
tflash_vdd: regulator-tflash_vdd {
compatible = "regulator-fixed";
regulator-name = "TFLASH_VDD";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>;
enable-active-high;
regulator-always-on;
};
tf_io: gpio-regulator-tf_io {
compatible = "regulator-gpio";
regulator-name = "TF_IO";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
gpios = <&gpio_ao GPIOAO_6 GPIO_ACTIVE_HIGH>;
gpios-states = <0>;
states = <3300000 0>,
<1800000 1>;
};
flash_1v8: regulator-flash_1v8 {
compatible = "regulator-fixed";
regulator-name = "FLASH_1V8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
vin-supply = <&vcc_3v3>;
regulator-always-on;
};
main_12v: regulator-main_12v {
compatible = "regulator-fixed";
regulator-name = "12V";
regulator-min-microvolt = <12000000>;
regulator-max-microvolt = <12000000>;
regulator-always-on;
};
vcc_5v: regulator-vcc_5v {
compatible = "regulator-fixed";
regulator-name = "5V";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-always-on;
vin-supply = <&main_12v>;
};
vcc_1v8: regulator-vcc_1v8 {
compatible = "regulator-fixed";
regulator-name = "VCC_1V8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
vin-supply = <&vcc_3v3>;
regulator-always-on;
};
vcc_3v3: regulator-vcc_3v3 {
compatible = "regulator-fixed";
regulator-name = "VCC_3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
vin-supply = <&vddao_3v3>;
regulator-always-on;
/* FIXME: actually controlled by VDDCPU_B_EN */
};
vddcpu: regulator-vddcpu {
/*
* MP8756GD Regulator.
*/
compatible = "pwm-regulator";
regulator-name = "VDDCPU";
regulator-min-microvolt = <721000>;
regulator-max-microvolt = <1022000>;
vin-supply = <&main_12v>;
pwms = <&pwm_AO_cd 1 1250 0>;
pwm-dutycycle-range = <100 0>;
regulator-boot-on;
regulator-always-on;
};
hub_5v: regulator-hub_5v {
compatible = "regulator-fixed";
regulator-name = "HUB_5V";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
vin-supply = <&vcc_5v>;
/* Connected to the Hub CHIPENABLE, LOW sets low power state */
gpio = <&gpio GPIOH_4 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
usb_pwr_en: regulator-usb_pwr_en {
compatible = "regulator-fixed";
regulator-name = "USB_PWR_EN";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
vin-supply = <&vcc_5v>;
/* Connected to the microUSB port power enable */
gpio = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
vddao_1v8: regulator-vddao_1v8 {
compatible = "regulator-fixed";
regulator-name = "VDDAO_1V8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
vin-supply = <&vddao_3v3>;
regulator-always-on;
};
vddao_3v3: regulator-vddao_3v3 {
compatible = "regulator-fixed";
regulator-name = "VDDAO_3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
vin-supply = <&main_12v>;
regulator-always-on;
};
hdmi-connector {
compatible = "hdmi-connector";
type = "a";
port {
hdmi_connector_in: endpoint {
remote-endpoint = <&hdmi_tx_tmds_out>;
};
};
};
};
&cpu0 {
cpu-supply = <&vddcpu>;
operating-points-v2 = <&cpu_opp_table>;
clocks = <&clkc CLKID_CPU_CLK>;
clock-latency = <50000>;
};
&cpu1 {
cpu-supply = <&vddcpu>;
operating-points-v2 = <&cpu_opp_table>;
clocks = <&clkc CLKID_CPU1_CLK>;
clock-latency = <50000>;
};
&cpu2 {
cpu-supply = <&vddcpu>;
operating-points-v2 = <&cpu_opp_table>;
clocks = <&clkc CLKID_CPU2_CLK>;
clock-latency = <50000>;
};
&cpu3 {
cpu-supply = <&vddcpu>;
operating-points-v2 = <&cpu_opp_table>;
clocks = <&clkc CLKID_CPU3_CLK>;
clock-latency = <50000>;
};
&ext_mdio {
external_phy: ethernet-phy@0 {
/* Realtek RTL8211F (0x001cc916) */
reg = <0>;
max-speed = <1000>;
interrupt-parent = <&gpio_intc>;
/* MAC_INTR on GPIOZ_14 */
interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
};
};
&ethmac {
pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
pinctrl-names = "default";
status = "okay";
phy-mode = "rgmii";
phy-handle = <&external_phy>;
amlogic,tx-delay-ns = <2>;
};
&gpio {
gpio-line-names =
/* GPIOZ */
"", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "",
/* GPIOH */
"", "", "", "", "",
"PIN_36", /* GPIOH_5 */
"PIN_26", /* GPIOH_6 */
"PIN_32", /* GPIOH_7 */
"",
/* BOOT */
"", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "",
/* GPIOC */
"", "", "", "", "", "", "", "",
/* GPIOA */
"", "", "", "", "", "", "", "",
"", "", "", "", "", "",
"PIN_27", /* GPIOA_14 */
"PIN_28", /* GPIOA_15 */
/* GPIOX */
"PIN_16", /* GPIOX_0 */
"PIN_18", /* GPIOX_1 */
"PIN_22", /* GPIOX_2 */
"PIN_11", /* GPIOX_3 */
"PIN_13", /* GPIOX_4 */
"PIN_7", /* GPIOX_5 */
"PIN_33", /* GPIOX_6 */
"PIN_15", /* GPIOX_7 */
"PIN_19", /* GPIOX_8 */
"PIN_21", /* GPIOX_9 */
"PIN_24", /* GPIOX_10 */
"PIN_23", /* GPIOX_11 */
"PIN_8", /* GPIOX_12 */
"PIN_10", /* GPIOX_13 */
"PIN_29", /* GPIOX_14 */
"PIN_31", /* GPIOX_15 */
"PIN_12", /* GPIOX_16 */
"PIN_3", /* GPIOX_17 */
"PIN_5", /* GPIOX_18 */
"PIN_35"; /* GPIOX_19 */
/*
* WARNING: The USB Hub on the Odroid-C4 needs a reset signal
* to be turned high in order to be detected by the USB Controller
* This signal should be handled by a USB specific power sequence
* in order to reset the Hub when USB bus is powered down.
*/
usb-hub {
gpio-hog;
gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>;
output-high;
line-name = "usb-hub-reset";
};
};
&gpio_ao {
gpio-line-names =
/* GPIOAO */
"", "", "", "",
"PIN_47", /* GPIOAO_4 */
"", "",
"PIN_45", /* GPIOAO_7 */
"PIN_46", /* GPIOAO_8 */
"PIN_44", /* GPIOAO_9 */
"PIN_42", /* GPIOAO_10 */
"",
/* GPIOE */
"", "", "";
};
&hdmi_tx {
status = "okay";
pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
pinctrl-names = "default";
hdmi-supply = <&vcc_5v>;
};
&hdmi_tx_tmds_port {
hdmi_tx_tmds_out: endpoint {
remote-endpoint = <&hdmi_connector_in>;
};
};
&ir {
status = "okay";
pinctrl-0 = <&remote_input_ao_pins>;
pinctrl-names = "default";
linux,rc-map-name = "rc-odroid";
};
&pwm_AO_cd {
pinctrl-0 = <&pwm_ao_d_e_pins>;
pinctrl-names = "default";
clocks = <&xtal>;
clock-names = "clkin1";
status = "okay";
};
&saradc {
status = "okay";
};
/* SD card */
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_c_pins>;
pinctrl-1 = <&sdcard_clk_gate_c_pins>;
pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
max-frequency = <200000000>;
sd-uhs-sdr12;
sd-uhs-sdr25;
sd-uhs-sdr50;
sd-uhs-sdr104;
disable-wp;
cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
vmmc-supply = <&tflash_vdd>;
vqmmc-supply = <&tf_io>;
};
/* eMMC */
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
pinctrl-1 = <&emmc_clk_gate_pins>;
pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
mmc-ddr-1_8v;
mmc-hs200-1_8v;
max-frequency = <200000000>;
disable-wp;
mmc-pwrseq = <&emmc_pwrseq>;
vmmc-supply = <&vcc_3v3>;
vqmmc-supply = <&flash_1v8>;
};
&uart_AO {
status = "okay";
pinctrl-0 = <&uart_ao_a_pins>;
pinctrl-names = "default";
};
&usb {
status = "okay";
vbus-supply = <&usb_pwr_en>;
};
&usb2_phy0 {
phy-supply = <&vcc_5v>;
};
&usb2_phy1 {
/* Enable the hub which is connected to this port */
phy-supply = <&hub_5v>;
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment