Commit 3307e902 authored by Krzysztof Kozlowski's avatar Krzysztof Kozlowski Committed by Mark Brown

regulator: max77686: Add GPIO control

Add enable control over GPIO for regulators supporting this: LDO20,
LDO21, LDO22, buck8 and buck9.

This is needed for proper (and full) configuration of the Maxim 77686
PMIC without creating redundant 'regulator-fixed' entries.
Signed-off-by: default avatarKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: default avatarMark Brown <broonie@kernel.org>
parent bfa21a0d
......@@ -26,6 +26,7 @@
#include <linux/bug.h>
#include <linux/err.h>
#include <linux/gpio.h>
#include <linux/of_gpio.h>
#include <linux/slab.h>
#include <linux/platform_device.h>
#include <linux/regulator/driver.h>
......@@ -45,6 +46,11 @@
#define MAX77686_DVS_MINUV 600000
#define MAX77686_DVS_UVSTEP 12500
/*
* Value for configuring buck[89] and LDO{20,21,22} as GPIO control.
* It is the same as 'off' for other regulators.
*/
#define MAX77686_GPIO_CONTROL 0x0
/*
* Values used for configuring LDOs and bucks.
* Forcing low power mode: LDO1, 3-5, 9, 13, 17-26
......@@ -82,6 +88,8 @@ enum max77686_ramp_rate {
};
struct max77686_data {
u64 gpio_enabled:MAX77686_REGULATORS;
/* Array indexed by regulator id */
unsigned int opmode[MAX77686_REGULATORS];
};
......@@ -100,6 +108,26 @@ static unsigned int max77686_get_opmode_shift(int id)
}
}
/*
* When regulator is configured for GPIO control then it
* replaces "normal" mode. Any change from low power mode to normal
* should actually change to GPIO control.
* Map normal mode to proper value for such regulators.
*/
static unsigned int max77686_map_normal_mode(struct max77686_data *max77686,
int id)
{
switch (id) {
case MAX77686_BUCK8:
case MAX77686_BUCK9:
case MAX77686_LDO20 ... MAX77686_LDO22:
if (max77686->gpio_enabled & (1 << id))
return MAX77686_GPIO_CONTROL;
}
return MAX77686_NORMAL;
}
/* Some BUCKs and LDOs supports Normal[ON/OFF] mode during suspend */
static int max77686_set_suspend_disable(struct regulator_dev *rdev)
{
......@@ -136,7 +164,7 @@ static int max77686_set_suspend_mode(struct regulator_dev *rdev,
val = MAX77686_LDO_LOWPOWER_PWRREQ;
break;
case REGULATOR_MODE_NORMAL: /* ON in Normal Mode */
val = MAX77686_NORMAL;
val = max77686_map_normal_mode(max77686, id);
break;
default:
pr_warn("%s: regulator_suspend_mode : 0x%x not supported\n",
......@@ -160,7 +188,7 @@ static int max77686_ldo_set_suspend_mode(struct regulator_dev *rdev,
{
unsigned int val;
struct max77686_data *max77686 = rdev_get_drvdata(rdev);
int ret;
int ret, id = rdev_get_id(rdev);
switch (mode) {
case REGULATOR_MODE_STANDBY: /* switch off */
......@@ -170,7 +198,7 @@ static int max77686_ldo_set_suspend_mode(struct regulator_dev *rdev,
val = MAX77686_LDO_LOWPOWER_PWRREQ;
break;
case REGULATOR_MODE_NORMAL: /* ON in Normal Mode */
val = MAX77686_NORMAL;
val = max77686_map_normal_mode(max77686, id);
break;
default:
pr_warn("%s: regulator_suspend_mode : 0x%x not supported\n",
......@@ -184,7 +212,7 @@ static int max77686_ldo_set_suspend_mode(struct regulator_dev *rdev,
if (ret)
return ret;
max77686->opmode[rdev_get_id(rdev)] = val;
max77686->opmode[id] = val;
return 0;
}
......@@ -197,7 +225,7 @@ static int max77686_enable(struct regulator_dev *rdev)
shift = max77686_get_opmode_shift(id);
if (max77686->opmode[id] == MAX77686_OFF_PWRREQ)
max77686->opmode[id] = MAX77686_NORMAL;
max77686->opmode[id] = max77686_map_normal_mode(max77686, id);
return regmap_update_bits(rdev->regmap, rdev->desc->enable_reg,
rdev->desc->enable_mask,
......@@ -229,6 +257,36 @@ static int max77686_set_ramp_delay(struct regulator_dev *rdev, int ramp_delay)
MAX77686_RAMP_RATE_MASK, ramp_value << 6);
}
static int max77686_of_parse_cb(struct device_node *np,
const struct regulator_desc *desc,
struct regulator_config *config)
{
struct max77686_data *max77686 = config->driver_data;
switch (desc->id) {
case MAX77686_BUCK8:
case MAX77686_BUCK9:
case MAX77686_LDO20 ... MAX77686_LDO22:
config->ena_gpio = of_get_named_gpio(np,
"maxim,ena-gpios", 0);
config->ena_gpio_flags = GPIOF_OUT_INIT_HIGH;
config->ena_gpio_initialized = true;
break;
default:
return 0;
}
if (gpio_is_valid(config->ena_gpio)) {
max77686->gpio_enabled |= (1 << desc->id);
return regmap_update_bits(config->regmap, desc->enable_reg,
desc->enable_mask,
MAX77686_GPIO_CONTROL);
}
return 0;
}
static struct regulator_ops max77686_ops = {
.list_voltage = regulator_list_voltage_linear,
.map_voltage = regulator_map_voltage_linear,
......@@ -283,6 +341,7 @@ static struct regulator_ops max77686_buck_dvs_ops = {
.name = "LDO"#num, \
.of_match = of_match_ptr("LDO"#num), \
.regulators_node = of_match_ptr("voltage-regulators"), \
.of_parse_cb = max77686_of_parse_cb, \
.id = MAX77686_LDO##num, \
.ops = &max77686_ops, \
.type = REGULATOR_VOLTAGE, \
......@@ -355,6 +414,7 @@ static struct regulator_ops max77686_buck_dvs_ops = {
.name = "BUCK"#num, \
.of_match = of_match_ptr("BUCK"#num), \
.regulators_node = of_match_ptr("voltage-regulators"), \
.of_parse_cb = max77686_of_parse_cb, \
.id = MAX77686_BUCK##num, \
.ops = &max77686_ops, \
.type = REGULATOR_VOLTAGE, \
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment